Kinetics of CO and H2 oxidation over CuO-CeO2 catalyst in H2 mixtures with CO2 and H2O

The kinetics of CO and H₂ oxidation over a CuO-CeO₂ catalyst were simultaneously investigated under reaction conditions of preferential CO oxidation (PROX) in hydrogen-rich mixtures with CO₂ and H₂O. An integral packed-bed tubular reactor was used to produce kinetic data for power-law kinetics for both CO and H₂ oxidations. The experimental results showed that the CO oxidation rate was essentially independent of H₂ and O₂ concentrations, while the H₂ oxidation rate was practically independent of CO and O₂ concentrations. In the CO oxidation, the reaction orders were 0.91, −0.37 and −0.62 with respect to the partial pressure of CO, CO₂ and H₂O, respectively. In the H₂ oxidation, the orders were 1.0, −0.48 and −0.69 with respect to the partial pressure of H₂, CO₂ and H₂O, respectively. The activation energies of the CO oxidation and the H₂ oxidation were 94.4 and 142 kJ/mol, respectively. The rate expressions of both oxidations were able to predict the performance of the PROX reactor with accuracy. The independence between the CO and the H₂ oxidation suggested different sites for CO and H₂ adsorption on the CuO-CeO₂ catalyst. Based on the results, we proposed a new reaction model for the preferential CO oxidation. The model assumes that CO adsorbs selectively on the Cu⁺ sites; H₂ dissociates and adsorbs on the Cu⁰ sites; the adsorbed species migrates to the interface between the copper components and the ceria support, and reacts there with the oxygen supplied by the ceria support; and the oxygen deficiency on the support is replenished by the oxygen in the reaction mixture.     

Design of a novel bifunctional catalyst IrFe/Al2O3 for preferential CO oxidation

In this study, a novel bifunctional catalyst IrFe/Al₂O₃, which is very active and selective for preferential oxidation of CO under H₂-rich atmosphere, has been developed. When the molar ratio of Fe/Ir was 5/1, the IrFe/Al₂O₃ catalyst performed best, with CO conversion of 68% and oxygen selectivity towards CO₂ formation of 86.8% attained at 100 °C. It has also been found that the impregnation sequence of Ir and Fe species on the Al₂O₃ support had a remarkable effect on the catalytic performance; the activity decreased following the order of IrFe/Al₂O₃ > co-IrFe/Al₂O₃ > FeIr/Al₂O₃. The three catalysts were characterized by XRD, H₂-TPR, FT-IR and microcalorimetry. The results demonstrated that when Ir was supported on the pre-formed Fe/Al₂O₃, the resulting structure (IrFe/Al₂O₃) allowed more metallic Ir sites exposed on the surface and accessible for CO adsorption, while did not interfere with the O₂ activation on the FeO_x species. Thus, a bifunctional catalytic mechanism has been proposed where CO adsorbed on Ir sites and O₂ adsorbed on FeO_x sites; the reaction may take place at the interface of Ir and FeO_x or via a spill-over process.     

The nature of metal oxide on adsorptive and catalytic properties of Pd/MeOx/Al2O3 catalysts

The role of ceria, niobium and molybdenum oxides on the promotion of the NO reduction by CO was studied. A bifunctional mechanism was discussed as a function of both the nature of interaction between metal oxide and palladium and the redox properties of each metal oxide.

The NO dissociation was better on the Pd/MoO₃/Al₂O₃ catalyst than on the Pd/CeO₂/Al₂O₃ and Pd/Nb₂O₅/Al₂O₃ catalysts. The explanation for the very high N₂ production on Pd–Mo catalyst during the TPD analysis may be attributed to the NO+Me^δ+ stoichiometric reaction.

The promoting effect of a reducible oxide for the NO+CO reaction at low temperature can be ascribed mainly to its easiness for a redox interchange and its interaction with the noble metal particles. This would increase the surface redox ability and favor the dynamic equilibrium needed for high N₂ selectivity.     

Reduction of NOx in C3H6/air mixtures over Cu/Al2O3 catalysts

The reduction of nitrogen oxides by propene in the presence of air under net oxidising conditions has been studied for two Cu/alumina catalysts of low (1%) and high (5%) copper loadings in a flow microreactor and by DRIFT. The reaction was studied in the range 473–773 K using mixtures of 2.5% NO, 1% C₃H₆ and 10% O₂ with a balance of nitrogen or helium, using samples which were pretreated in air at 673 K and also over samples which had been pre-exposed to SO₂ at 473 K. The surface species present under reaction conditions have been identified and the sensitivity of their adsorption sites in the two different loaded catalysts to SO₂ pre-treatment has been investigated. SO₂ adsorption enhanced NO adsorption at 473 K in the absence of oxygen and, in reaction, enhanced formation of NCO species leading to increased levels of adsorbed CO as a decomposition product.     

CO oxidation and oxygen-assisted CO adsorption/desorption on Ag/MnOx catalysts

A series of Ag-doped manganese oxide catalyst were synthesized by the reflux method in an acid medium. The surface structure of the catalysts was characterized by N₂ adsorption, XRD and TEM experiments. The catalysts showed excellent catalytic activity for CO oxidation. The adsorption and oxidation of CO on a 1.0% Ag/MnO_x catalyst between 393 and 493 K were studied by means of single pulse experiments in a TAP reactor. The adsorption of CO was reversible at these temperatures and CO₂ was formed in an oxidation reaction of CO and lattice oxygen. Curve fitting to the experimental TAP response curves of the reactant and product was used to determine the kinetic parameters for the elementary steps. The activation energies were 83 kJ/mol for CO desorption, 31 kJ/mol for CO₂ desorption, and 116 kJ/mol for the surface CO oxidation by lattice oxygen. In addition, the effect of coadsorbed O₂ on CO adsorption was studied by the TAP technique. Below 353 K, there was a sharp increase, by about one order of magnitude, in the rate constant of CO adsorption promoted by the presence of coadsorbed O₂.     

Investigation of CO oxidation and NO reduction on three-way monolith catalysts with transient response techniques

The kinetics of CO oxidation and NO reduction reactions over alumina and alumina-ceria supported Pt, Rh and bimetallic Pt/Rh catalysts coated on metallic monoliths were investigated using the step response technique at atmospheric pressure and at temperatures 30–350°C. The feed step change experiments from an inert flow to a flow of a reagent (O₂, CO, NO and H₂) showed that the ceria promoted catalysts had higher adsorption capacities, higher reaction rates and promoting effects by preventing the inhibitory effects of reactants, than the alumina supported noble metal catalysts. The effect of ceria was explained with adsorbate spillover from the noble metal sites to ceria. The step change experiments CO/O₂ and O₂/CO also revealed the enhancing effect of ceria. The step change experiments NO/H₂ and H₂/NO gave nitrogen as a main reduction product and N₂O as a by-product. Preadsorption of NO on the catalyst surface decreased the catalyst activity in the reduction of NO with H₂. The CO oxidation transients were modeled with a mechanism which consistent of CO and O₂ adsorption and a surface reaction step. The NO reduction experiments with H₂ revealed the role of N₂O as a surface intermediate in the formation of N₂. The formation of NN bonding was assumed to take place prior to, partly prior to or totally following to the NO bond breakage. High NO coverage favors N₂O formation. Pt was shown to be more efficient than Rh for NO reduction by H₂.     

Study of the reaction of NOx and soot on Fe2O3 catalyst in excess of O2

This study addresses the catalytic reaction of NO_x and soot into N₂ and CO₂ under O₂-rich conditions. To elucidate the mechanism of the soot/NO_x/O₂ reaction and particularly the role of the catalyst -Fe₂O₃ is used as model sample. Furthermore, a series of examinations is also made with pure soot for reference purposes. Temperature programmed oxidation and transient experiments in which the soot/O₂ and soot/NO reaction are temporally separated show that the NO reduction occurs on the soot surface without direct participation of the Fe₂O₃ catalyst. The first reaction step is the formation of CC(O) groups that is mainly associated with the attack of oxygen on the soot surface. The decomposition of these complexes leads to active carbon sites on which NO is adsorbed. Furthermore, the oxidation of soot by oxygen provides a specific configuration of active carbon sites with suitable atomic orbital orientation that enables the chemisorption and dissociation of NO as well as the recombination of two adjacent N atoms to evolve N₂. Moreover, carbothermal reaction, high resolution transmission electron microscopy and isotopic studies result in a mechanistic model that describes the role of the Fe₂O₃ catalyst. This model includes the dissociative adsorption of O₂ on the iron oxide, surface migration of the oxygen to the contact points of soot and catalyst and then final transfer of O to the soot. Moreover, our experimental data suggest that the contact between both solids is maintained up to high conversion levels thus resulting in continuous oxygen transfer from catalyst to soot. As no coordinative interaction of soot and Fe₂O₃ catalyst is evidenced by diffuse reflectance infrared Fourier transform spectroscopy a van der Waals type interaction is supposed.     

An infrared study of the behavior of SO2 and NOx over carbon and carbon-supported catalysts

The heterogeneous reactivity of NO_x and SO₂ with carbon has been investigated with FT-IR spectroscopy. The interaction between NO and SO₂ on carbon surface have been studied in the presence and in the absence of oxygen. Thermal stabilities of surface structures, formed as a result of NO_x and SO₂ chemisorption have been determined by means of FT-IR spectroscopy. During the reaction of NO/O₂ mixture with carbon the surface species, including C–NO₂, C–ONO, C–NCO and anhydride structures are formed. It has been found that SO₂ retards the oxidation reaction of carbon by oxygen. The oxidation of SO₂ on carbon was found to be greatly enhanced by the presence of NO + O₂ mixture. The adsorption capacity of cellulose based carbon, catalytic NO_x decomposition and TPD was studied using a fixed bed flow reactor.     

Catalytic effect of platinum on the kinetics of carbon oxidation by NO2 and O2

The effect of a commercial Pt/Al₂O₃ catalyst on the oxidation by NO₂ and O₂ of a model soot (carbon black) in conditions close to automotive exhaust gas aftertreatment is investigated. Isothermal oxidations of a physical mixture of carbon black and catalyst in a fixed bed reactor were performed in the temperature range 300–450 °C. The experimental results indicate that no significant effect of the Pt catalyst on the direct oxidation of carbon by O₂ and NO₂ is observed. However, in presence of NO₂–O₂ mixture, it is found that besides the well established catalytic reoxidation of NO into NO₂, Pt also exerts a catalytic effect on the cooperative carbon–NO₂–O₂ oxidation reaction. An overall mechanism involving the formation of atomic oxygen over Pt sites followed by its transfer to the carbon surface is established. Thus, the presence of Pt catalyst increases the surface concentration of –C(O) complexes which then react with NO₂ leading to an enhanced carbon consumption. The resulting kinetic equation allows to model more precisely the catalytic regeneration of soot traps for automotive applications.     

New degradation mechanism of Ti/IrO2 + MnO2 anode for oxygen evolution in 0.5 M H2SO4 solution

Degradation mechanism of Ti/IrO₂(0.7) + MnO₂(0.3) anode for oxygen evolution was studied in 0.5 M H₂SO₄ solution by field emission scanning electron microscopes (FESEM), Tafel slope, X-ray diffraction (XRD) and electrochemical impedance spectroscopic (EIS). The whole surface of the non-electrolyzed Ti/IrO₂(0.7) + MnO₂(0.3) anode consisted of nano-IrO₂ poles array. The anode surface had hardly discovered cracks and had compact morphology that can prevent the electrolyte from entering the Ti/oxide interface and an insulating TiO₂ film from growing on the Ti-based surface. An insulating TiO₂ phase had not been generated on the Ti/oxide interface during the process of O₂ evolution and the inactive anode surface still remained mass of the IrO₂ and MnO₂ oxides. The chemical dissolution of Ti/IrO₂(0.7) + MnO₂(0.3) anode coating was not the main reason for electrode degradation in 0.5 M H₂SO₄ solution. The degradation mechanism of Ti/IrO₂(0.7) + MnO₂(0.3) anode differed from other conventional oxide electrodes for O₂ evolution in acid medium. The platforms of Tafel slope and anode potential (900–1050 h) indicated that the change of the oxygen evolution reaction (OER) mechanism was the main reason for degradation of Ti/IrO₂(0.7) + MnO₂(0.3) anode due to the change of adsorption intermediate.     

Properties of adsorbed oxygen on Au/SiO2

Oxygen adsorption on silica-supported gold catalyst from NO₂ and O₂ exposures were investigated by temperature-programmed desorption spectroscopy under a vacuum condition. NO₂ and O₂ exposures of the surface of the catalyst at room temperature gave adsorbed oxygen in atomic state. Adsorbed oxygen penetrated beneath the gold with lower activation energy for NO₂ exposure than for O₂ exposure. Adsorbed oxygen in oxidic state which was desorbed above 600 K altered the surface properties of gold and resulted in the decrease of activation energy for oxygen to penetrate beneath the gold surface.     

The effect of Fe on the catalytic behavior of model Pd-Rh/CeO2-Al2O3 three-way catalyst

The present work attempts to address the issue whether iron (Fe) which is accumulated on the surface of “three-way” catalysts (TWCs) used in gasoline-driven cars is a true chemical poison of their catalytic activity. This important issue from a scientific and technological point of view is addressed via catalytic activity, temperature-programmed surface reaction (TPSR), and X-ray photoelectron spectroscopy (XPS) measurements over a model TWC (1 wt% Pd–Rh/20 wt% CeO₂–Al₂O₃). It was found that deposition of Fe up to the level of 0.4 wt% (an average concentration found in aged commercial TWCs) on the model TWC does not deteriorate its activity towards CO and C₃H₆ oxidation, and reduction of NO by H₂. Instead it was found that iron improves significantly the T₅₀ parameter in the activity versus temperature profile. Small Fe clusters in contact with the noble metal (Pd and Rh) particles due to the lower work function of Fe compared to Pd and Rh act likely as a source of electron flow towards the noble metals (as evidenced by XPS measurements), thus altering their surface work function and adsorption energetics of reaction intermediates. The latter have increased significantly the activity of the model TWC towards oxidation of CO and propylene, and to a lesser extent the activity towards the reduction of NO by H₂. The presence of Fe on the surface of the model TWC provided and/or created also new active catalytic sites for the reactions investigated. According to previous work from this laboratory, iron up to the level of 0.4 wt% was shown not to deteriorate the oxygen storage capacity (OSC) of the same model TWC used in the present work. Thus, it could be concluded that Fe when deposited on a commercial TWC at least up to the level of 0.4 wt% acts likely as a promoter than a poison of its catalytic activity.     

Passivation of a Co–Ru/γ-Al2O3 Fischer–Tropsch catalyst

Passivation of highly dispersed metal catalysts after reduction is necessary prior to exposure to air due to the exothermicity of metal oxidation. This exothermicity can result in a significant increase in temperature of the catalyst resulting in catalyst degradation and a potential fire hazard. This paper reports the results of a study of passivation of Ru-promoted Co/alumina. Passivations using CO and CO+H₂ mixtures were compared to the standard method of passivation using small concentrations of O₂. Passivation by CO+H₂ resulted in a lower temperature rise upon exposure to air than oxygen passivation. Passivation using CO/H₂=10 resulted in a catalyst whose catalytic activity for CO hydrogenation was able to be recovered after exposure to air by re-reduction similar to after oxygen passivation. CO passivation yielded a catalyst that was not able to be as well recovered upon re-reduction, probably due to the formation of graphitic carbon. Exposure of the CO/H₂ passivated catalyst to air for at least 90 min actually made it easier to recover the original activity upon re-reduction. This is probably related to the oxidation of the carbidic passivation layer during air exposure.     

Re-investigating the CO oxidation mechanism over unsupported MnO, Mn2O3 and MnO2 catalysts

Kinetic study of CO oxidation in combination with experiments of temperature-programmed oxidation (TPO) and reduction (TPR) have been performed on various unsupported crystalline manganese oxides (MnO_x); while the reactivity shows an order of MnO ≤ MnO₂ < Mn₂O₃ in a mixture of unit ratio of O₂/CO at/below 523 K. We propose that under the current conditions the interaction of adsorbed CO and O is mainly responsible for CO₂ formation on Mn₂O₃ and MnO₂ catalysts, following either the Langmuir–Hinshelwood mechanism or Eley–Rideal mechanism. Meanwhile, direct evidence from transient CO oxidation suggests that the Mars-van-Krevelen mechanism may occur for all catalysts simultaneously, especially, it is predominant for the MnO catalyst. The evidence of structural modifications during reaction was confirmed by Raman spectra obtained from used MnO.     

Comparison of catalytic activity and selectivity of Pd/(OSC + Al2O3) and (Pd + OSC)/Al2O3 catalysts

The effect of the Pd addition method into the fresh Pd/(OSC + Al₂O₃) and (Pd + OSC)/Al₂O₃ catalysts (OSC material = Ce_xZr_1−xO₂ mixed oxides) was investigated in this study. The CO + NO and CO + NO + O₂ model reactions were studied over fresh and aged catalysts. The differences in the fresh catalysts were insignificant compared to the aged catalysts. During the CO + NO reaction, only small differences were observed in the behaviour of the fresh catalysts. The light-off temperature of CO was about 20 °C lower for the fresh Pd/(OSC + Al₂O₃) catalyst than for the fresh (Pd + OSC)/Al₂O₃ catalyst during the CO + NO + O₂ reaction. For the aged catalysts lower NO reduction and CO oxidation activities were observed, as expected. Pd on OSC-containing alumina was more active than Pd on OSC material after the agings. The activity decline is due to a decrease in the number of active sites on the surface, which was observed as a larger Pd particle size for aged catalysts than for fresh catalysts. In addition, the oxygen storage capacity of the aged Pd/(OSC + Al₂O₃) catalyst was higher than that of the (Pd + OSC)/Al₂O₃ catalyst.     

In situ IR and pulse reaction studies on the active oxygen species over SrF2/Nd2O3 catalyst for oxidative coupling of methane

Pulse reaction method and in situ IR spectroscopy were used to characterize the active oxygen species for oxidative coupling of methane (OCM) over SrF₂/Nd₂O₃ catalyst. It was found that OCM activity of the catalyst was very low in the absence of gas phase oxygen, which indicated that lattice oxygen species contributed little to the yield of C₂ hydrocarbons. IR band of superoxide species (O₂⁻) was detected on the O₂-preadsorbed SrF₂/Nd₂O₃. The substitution of ¹⁸O₂ isotope for ¹⁶O₂ caused the IR band of O₂⁻ at 1128 cm⁻¹ to shift to lower wavenumbers (1094 and 1062 cm⁻¹), consistent with the assignment of the spectra to the O₂⁻ species. A good correlation between the rate of disappearance of surface O₂⁻ and the rate of formation of gas phase C₂H₄ was observed upon interaction of CH₄ with O₂-preadsorbed catalyst at 700 °C. The O₂⁻ species was also observed on the catalyst under working condition. These results suggest that O₂⁻ species is the active oxygen species for OCM reaction on SrF₂/Nd₂O₃ catalyst.     

Catalytic activity of RuO2(1 1 0) in the oxidation of CO

The primary reason why the RuO₂(1 1 0) surface is much more active in the oxidation of CO than the corresponding metal Ru(0 0 0 1) surface is correlated with the weaker oxygen bonding on RuO₂(1 1 0) compared to chemisorbed oxygen on Ru(0 0 0 1). The RuO₂(1 1 0) surface stabilizes at least two potentially active oxygen species, i.e., bridging O and on-top O atoms. Together with various adsorption sites for CO during the reaction, the CO oxidation reaction over RuO₂(1 1 0) becomes quite complex. Using the techniques of temperature programmed reaction and desorption in combination with state-of-the-art density functional theory calculation we studied the CO oxidation reaction over RuO₂(1 1 0) in the temperature range of 300–400 K. We show that the CO oxidation on RuO₂(1 1 0) surface is not dominated by the recombination of CO with on-top O, although the binding energy of the on-top O is 1.4 eV lower than that of the bridging O atom.     

Influence of the pre-treatment on the structure and reactivity of Ir/γ-Al2O3 catalysts in the selective reduction of nitric oxide by propene

The selective catalytic reduction (SCR) of nitric oxide by propene over Ir/Al₂O₃ under lean-burn conditions (1000 vpm NO, 2000 vpm C₃H₆, 500 vpm CO, 10 vol.% O₂) was studied. The activity was shown to be strongly enhanced after exposure of the catalyst at 600°C under the reaction mixture, irrespective of the oxidising or reducing pre-treatment. Simultaneously, the Ir dispersion decreased from 78 to 10%. The influence of each component of the reaction mixture on the activation process was examined. The presence of both CO and O₂ was found to be necessary to activate Ir/Al₂O₃ while NO would not be. In situ FT-IR results revealed that initially fully oxidised Ir particles partially reduced in the feed to form Ir⁰ reduced surface sites (νCO at 2060 cm⁻¹) which adsorbed CO up to 350–400°C. The activation under reactants was related to the formation of these sites. The presence of reduced (or partially reduced) Ir sites, possibly siting at the surface of IrO₂ particles and stabilised by CO adsorption, was proposed to be responsible for the SCR activity.     

Potential rare earth modified CeO2 catalysts for soot oxidation: I. Characterisation and catalytic activity with O2

Ceria (CeO₂) and rare-earth modified ceria (CeReO_x with Re = La, Pr, Sm, Y) catalysts are prepared by nitrate precursor calcination and are characterised by BET surface area, XRD, H₂-TPR, and Raman spectroscopy. Potential of the catalysts in the soot oxidation is evaluated in TGA with a feed gas containing O₂. Seven hundred degree Celsius calcination leads to a decrease in the surface area of the rare-earth modified CeO₂ compared with CeO₂. However, an increase in the meso/macro pore volume, an important parameter for the soot oxidation with O₂, is observed. Rare-earth ion doping led to the stabilisation of the CeO₂ surface area when calcined at 1000 °C. XRD, H₂-TPR, and Raman characterisation show a solid solution formation in most of the mixed oxide catalysts. Surface segregation of dopant and even separate phases, in CeSmO_x and CeYO_x catalysts, are, however, observed. CePrO_x and CeLaO_x catalysts show superior soot oxidation activity (100% soot oxidation below 550 °C) compared with CeSmO_x, CeYO_x, and CeO₂. The improved soot oxidation activity of rare-earth doped CeO₂ catalysts with O₂ can be correlated with the increased meso/micro pore volume and stabilisation of external surface area. The segregation of the phases and the enrichment of the catalyst surface with unreducible dopant decrease the intrinsic soot oxidation activity of the potential CeO₂ catalytic sites. Doping CeO₂ with a reducible ion such as Pr^4+/3+ shows an increase in the soot oxidation. However, the ease of catalyst reduction and the bulk oxygen-storage capacity is not a critical parameter in the determination of the soot oxidation activity. During the soot oxidation with O₂, the function of the catalyst is to increase the ‘active oxygen’ transfer to the soot surface, but it does not change the rate-determining step, as evident from the unchanged apparent activation energy (around 150 kJ mol⁻¹), for the catalysed and un-catalysed soot oxidation. Spill over of oxygen on the soot surface and its subsequent adsorption at the active carbon sites is an important intermediate step in the soot oxidation mechanism.     

High combustion activity of methane induced by reforming gas over Ni/Al2O3 catalysts

During the reactions related to oxidative steam reforming and combustion of methane over -alumina-supported Ni catalysts, the temperature profiles of the catalyst bed were studied using an infrared (IR) thermograph. IR thermographical images revealed an interesting result: that the temperature at the catalyst bed inlet is much higher under CH₄/H₂O/O₂/Ar = 20/10/20/50 than under CH₄/H₂O/O₂/Ar = 10/0/20/70; the former temperature is comparable to that over noble metal catalysts such as Pt and Pd. Based on the temperature-programmed reduction and oxidation measurements over fresh and used catalysts, the metallic Ni is recognized at the catalyst bed inlet under CH₄/H₂O/O₂/Ar = 20/10/20/50, although it is mainly oxidized to NiAl₂O₄ under CH₄/H₂O/O₂/Ar = 10/0/20/70. This result indicates that the addition of reforming gas (CH₄/H₂O = 10/10) to the combustion gas (CH₄/O₂ = 10/20) can stabilize Ni species in the metallic state even under the presence of oxygen in the gas phase. This would account for its extremely high combustion activity.