Crystallization kinetics of poly (L‐lactic acid)/montmorillonite nanocomposites under isothermal crystallization condition

Poly(L ‐lactic acid)/o‐MMT nanocomposites, incorporating various amounts of organically modified montmorillonite (o‐MMT; 0–10 wt %), were prepared by solution intercalation. The montmorillonite (MMT) was organically modified with dilauryl dimethyl ammonium bromide (DDAB) by ion exchange. Transmission electron microscopy (TEM) and X‐ray diffraction (XRD) reveal that the o‐MMT was exfoliated in a poly(L ‐lactic acid), (PLLA) matrix. A series of the test specimens were prepared and subjected to isothermal crystallization at various temperatures (T₁–T₅). The DSC plots revealed that the PLLA/o‐MMT nanocomposites that were prepared under nonisothermal conditions exhibited an obvious crystallization peak and recrystallization, but neat PLLA exhibited neither. The PLLA/o‐MMT nanocomposites (2–10 wt %) yielded two endothermic peaks only under isothermal conditions at low temperature (T₁), and the intensity of Tm₂ (the higher melting point) was proportional to the o‐MMT content (at around 171°C). The melting point of the test samples increased with the isothermal crystallization temperature. In the Avrami equation, the constant of the crystallization rate (k) was inversely proportional to the isothermal crystallization temperature and increased with the o‐MMT content, especially at low temperature (T₁). The Avrami exponent (n) of the PLLA/o‐MMT nanocomposites (4–10 wt %) was 2.61–3.56 higher than that of neat PLLA, 2.10–2.56, revealing that crystallization occurred in three dimensions. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and Thermal Properties of Boron-Nitrogen Containing Phenol Formaldehyde Resin/MMT Nanocomposites

The nanocomposites of boron-nitrogen containing phenol formaldehyde resin (BNPFR) and organic-montmorillonite (O-MMT) (BNPFR/MMT) were synthesized from phenol, formaldehyde, boric acid, ammonia water and montmorillonite. The thermal properties of nanocomposites were characterized. The results show that the remaining weight fraction of BNPFR is 68.82% at 750°C, but the hybrid nanocomposite (BNPFR/MMT) is 75.51%. At 900°C, the remaining weight fraction of 7% O-MMT containing nanocomposites is 72.89%, which is 11.46% higher than BNPFR. The mechanical loss peak temperature T _p of BNPFR/MMT nanocomposites is 194.6°C, which is higher 7.3°C than that of BNPFR.     

Polymerizable ionic liquids for the preparation of polystyrene/clay composites

Polymerizable ionic liquids (ILs) 1‐methyl‐3‐(4‐vinylbenzyl)imidazolium chloride, 1‐hexyl‐3‐(4‐vinylbenzyl)imidazolium chloride and 1‐dodecyl‐3‐(4‐vinylbenzyl)imidazolium chloride were prepared and used as new surfactants for the modification of montmorillonite (MMT). Functionalized MMTs were prepared by cationic exchange between sodium MMT and each of the ILs. Polystyrene (PS)/MMT composites were subsequently prepared by in situ intercalative free radical polymerization of styrene containing dispersed organophilic MMT. Exfoliation of MMT in the PS matrix was achieved only for MMT functionalized with the 1‐dodecyl‐3‐(4‐vinylbenzyl)imidazolium‐based IL as revealed by X‐ray diffraction and electron microscopy. The exfoliated composites showed good transparency and higher decomposition temperature than virgin polymer matrix, particularly pronounced under air atmosphere (ΔT_max = 66 °C), data comparable to or even greater than those reported in the literature for exfoliated PS nanocomposites. Copyright © 2012 Society of Chemical Industry     

Physical properties of poly(trimethylene terephthalate)/organoclay nanocomposites obtained via melt compounding and in situ polymerization

Two series of poly(trimethylene terephthalate) (PTT) nanocomposites, containing an organically modified montmorillonite (MMT) clay (1,2‐aminododecanoic acid (ADA)–intercalated MMT) were prepared via melt compounding and in situ polymerization methods using dimethyl terephthalate (DMT) and 1,3‐propanediol (PDO). The effect of different methods of preparation and varying organoclay contents (1−5 wt%) on the structural, morphological, thermal, and mechanical properties were investigated. The results of wide‐angle X‐ray diffraction (WAXD) and transmission electron microscope (TEM) suggested the possible existence of intercalation morphology between ADA‐MMT and the PTT matrix obtained from melt compounding, and mostly exfoliation state from in situ polymerization depending on the amount of organoclay. From DSC studies, in melt compounding case, the addition of ADA‐MMT in PTT increases melt‐crystallization (T_cm) peak temperature by 14−15°C irrespective of the clay content. However, the melting temperature (T_m) of pristine PTT remains unchanged with increasing clay content. In the case of in situ polymerization, the T_cm and T_m peaks are shifted towards lower temperature with increasing clay content. Dynamic mechanical thermal analysis (DMTA) studies on melt compounded samples revealed a marginal lowering of glass transition temperature (T_g) irrespective of clay content, and a noticeable decrease in T_g with increasing clay content for in situ polymerized samples. The PTT/ADA‐MMT nanocomposites via melt compounding showed higher initial modulus and yield stress, and lower strain at break compared with in situ polymerization with increasing clay content. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Super-crosslinked ionic liquid-intercalated montmorillonite/epoxy nanocomposites: Cure kinetics,viscoelastic behavior and thermal degradation mechanism

Super-crosslinked epoxy nanocomposites containing N-octadecyl-N′-octadecyl imidazolium iodide (IM)-functionalized montmorillonite (MMT-IM) nanoplatelets were developed and examined for cure kinetics, viscoelastic behavior and thermal degradation kinetics. The structure and morphology of MMT-IM were characterized by FTIR, XRD, TEM, and TGA. Synthesized MMT-IM revealed synergistic effects on the network formation, the glass transition temperature (T_g) and thermal stability of epoxy. Cure and viscoelastic behaviors of epoxy nanocomposites containing 0.1 wt% MMT and MMT-IM were compared based on DSC and DMA, respectively. Activation energy profile as a function of the extent of cure was obtained. DMA results indicated a strong interface between imidazole groups of MMT-IM and epoxy, which caused a significant improvement in storage modulus and the T_g of epoxy. Network degradation kinetics of epoxy containing 0.5, 2.0, and 5.0 wt% MMT and MMT-IM were compared by using Friedman, Kissinger-Akahira-Sunose (KAS), Flynn-Wall-Ozawa (FWO) and the modified Coats-Redfern methods. Although addition of MMT to epoxy was detrimental to the T_g value, as featured by a fall from 94.1°C to 89.7°C detected by DMA method, and from 103.3°C to 97.9°C by DSC method, respectively. By contrast, meaningful increase in such values were observed in the same order from 94.1°C to 94.7°C and from 103.3°C to 104.7°C for super-crosslinked epoxy/MMT-IM systems.     

Crystallization behavior of polypropylene/polyamide 6/montmorillonite nanocomposites

Polymer blended materials such as polyamide 6 (PA6)/polypropylene (PP) blends have received considerable attention in recent years. To improve the compatibility of PA6 and PP, compatibilizers like maleic anhydride‐g‐polypropylene (MPP) are often added. In addition, organically modified montmorillonite (MMT) is also used to improve the properties of various materials. In this work, the crystallization behavior of PP/PA6/MMT nanocomposites with MPP compatibilizer was investigated systematically. The annealing process effectively improved the crystallization of α‐PP. The crystallization temperature (T_c) of PA6 was increased by ca 2–3 °C on introducing MPP or MMT alone to the PP/PA6 system, whereas T_c of PP underwent no obvious change. However, when MPP and MMT were added simultaneously, T_c of PP and PA6 increased by 6.6 and 4.2 °C, respectively, and a new crystallization peak corresponding to PP‐g‐PA6 copolymer phase was observed at 162.5 °C. The combined effect of MPP and MMT led to better compatibility of PP with PA6. Moreover, the results of a non‐isothermal crystallization kinetics experiment revealed that the simultaneous introduction of MPP and MMT markedly shortened the crystallization time. Copyright © 2010 Society of Chemical Industry     

Preparation and properties of bio‐based epoxy montomorillonite nanocomposites derived from polyglycerol polyglycidyl ether and ε‐polylysine

Glycerol polyglycidyl ether (GPE) and polyglycerol polyglycidyl ether (PGPE) were cured with ε‐poly(L ‐lysine) (PL) using epoxy/amine ratios of 1 : 1 and 2 : 1 to create bio‐based epoxy cross‐linked resins. When PGPE was used as an epoxy resin and the epoxy/amine ratio was 1 : 1, the cured neat resin showed the greatest glass transition temperature (T_g), as measured by differential scanning calorimetry. Next, the mixture of PGPE, PL, and montomorillonite (MMT) at an epoxy/amine ratio of 1 : 1 in water was dried and cured finally at 110°C to create PGPE‐PL/MMT composites. The X‐ray diffraction and transmission electron microscopy measurements revealed that the composites with MMT content 7–15 wt % were exfoliated nanocomposites and the composite with MMT content 20 wt % was an intercalated nanocomposite. The T_g and storage modulus at 50–100°C for the PGPE‐PL/MMT composites measured by DMA increased with increasing MMT content until 15 wt % and decreased at 20 wt %. The tensile strength and modulus of the PGPE‐PL/MMT composites (MMT content 15 wt %: 42 and 5300 MPa) were much greater than those of the cured PGPE‐PL resin (4 and 6 MPa). Aerobic biodegradability of the PGPE‐PL in an aqueous medium was ～ 4% after 90 days, and the PGPE‐PL/MMT nanocomposites with MMT content 7–15 wt % showed lower biodegradability. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and properties of polystyrene–clay nanocomposites via in situ intercalative polymerization

Organophilic montmorillonite (MMT) was prepared by ion exchange between Na⁺ ions in the clay and twin benzyldimethyloctadecylammonium bromine cations in an aqueous medium. The organophilic MMT particles were easily dispersed and swollen in styrene monomer. Polystyrene–MMT nanocomposites were prepared by the free‐radical polymerization of styrene containing dispersed clay. The intercalation spacing in the nanocomposites and the degree of dispersion of these composites were investigated with X‐ray diffraction and transmission electron microscopy, respectively. The nanocomposites had higher weight‐average molecular weights, lower glass‐transition temperatures, and better thermal stability (the decomposition temperature was improved by ca. 70°C) than the virgin polystyrene. The rheological behavior of the polystyrene–MMT nanocomposites was also studied. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 201–207, 2005     

Polylactide/transition metal ion modified montmorillonite nanocomposite—a critical evaluation of mechanical performance and thermal stability

Polylactide (PLA) nanocomposite was prepared by melt blending of PLA and transition metal ion (TMI) adsorbed montmorillonite (MMT). PLA nanocomposite was characterized for mechanical performance, and the results revealed that the tensile modulus, flexural modulus, and impact strength were increased marginally. The nanocomposite was optimized at 5 wt% of TMI‐modified MMT (TMI‐MMT) loading. Thermogravimetric analysis displayed increase in onset of degradation temperature, and differential scanning calorimetry showed marginal increase in glass transition temperature (T_g) and melting temperature (T_m) in case of PLA nanocomposites, when compared with virgin PLA. The flammability testing of nanocomposites indicated good fire retardance characters. X‐ray diffraction patterns of TMI‐MMT and the corresponding nanocomposites indicated an intercalation of the metal ions into the clay interlayer. Fourier transform infrared spectroscopy analysis indicate formation of [Zn(EDA)₂]²⁺ and [Cu(EDA)₂]²⁺ complexes in the MMT interlayer. Dynamic mechanical analysis shows increase in glass transition temperature (T_g) and storage modulus (E′) in case of PLA nanocomposites reinforced with 5 wt% modified MMT. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Preparation,characterization, and thermal properties of polystyrene‐block‐quaternized poly(4‐vinylpyridine)/Montmorillonite nanocomposites

Polystyrene‐block‐poly(4‐vinylpyridine) (PS‐b‐P4VP) was synthesized by two steps of reversible addition‐fragmentation transfer (RAFT) polymerization of styrene (St) and 4‐vinylpyridine (4VP) successively. After P4VP block was quaternized with CH₃I, PS‐b‐quaternized P4VP/montmorillonite (PS‐b‐QP4VP/MMT) nanocomposites were prepared by cationic exchange reactions of quaternary ammonium ion in the PS‐b‐QP4VP with ions in MMT. The results obtained from X‐ray diffraction (XRD) and transmission electron microscopy (TEM) images demonstrate that the block copolymer/MMT nanocomposites are of intercalated and exfoliated structures, and also a small amount of silicates' layers remained in the original structure; differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) results show that the nanocomposites displayed higher glass transition temperature (T_g) and higher thermal stability than that of the corresponding copolymers. The blending of PS‐b‐QP4VP/MMT with commercial PS makes MMT to be further separated, and the MMT was homogeneously dispersed in the polymer matrix. The enhancement of thermal stability of PS/PS‐b‐QP4VP/MMT is about 20°C in comparison with commercial PS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:1950–1958, 2006     

Synthesis and properties of polyimide (containing naphthalene) nanocomposites with organo‐modified montmorillonites

2,7‐Bis(4‐aminophenoxy) naphthalene (BAPN), a naphthalene‐containing diamine, was synthesized and polymerized with a 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride (BTDA) to obtain a polyimide (PI) via thermal imidization. To enhance the thermal and mechanical properties of the polymer, PI–Montmorillonite (MMT) nanocomposites were prepared from a DMAc solution of poly(amic acid) and a DMAc dispersion of MMT, which were organo‐modified with various amounts of n‐dodecylamine (DOA) or cetylpyridium chloride (CPC). FTIR, XRD, and TEM (transmission electron microscopy) were used to verify the incorporation of the modifying agents into the clay structure and the intercalation of the organoclay into the PI matrix. Results demonstrated that the introduction of a small amount of MMT (up to 5%) led to the improvement in thermal stability and mechanical properties of PI. The decomposition temperature of 5% weight loss (T_d,5%) in N₂ was increased by 46 and 36°C in comparison with pristine PI for the organoclay content of 5% with DOA and CPC, respectively. The nanocomposites were simultaneously strengthened and toughened. The dielectric constant, CTE, and water absorption were decreased. However, at higher organoclay contents (5–10%), these properties were reduced because the organoclay was poorly dispersed and resulted in aggregate formation. The effects of different organo‐modifiers on the properties of PI–MMT nanocomposite were also studied; the results showed that DOA was comparable with CPC. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Effect of organic modifiers and silicate type on filler dispersion,thermal, and mechanical properties of ABS‐clay nanocomposites

Acrylonitrile–butadiene–styrene (ABS)–clay composite and intercalated nanocomposites were prepared by melt processing, using Na‐montmorillonite (MMT), several chemically different organically modified MMT (OMMT) and Na‐laponite clays. The polymer–clay hybrids were characterized by WAXD, TEM, DSC, TGA, tensile, and impact tests. Intercalated nanocomposites are formed with organoclays, a composite is obtained with unmodified MMT, and the nanocomposite based on synthetic laponite is almost exfoliated. An unintercalated nanocomposite is formed by one of the organically modified clays, with similar overall stack dispersion as compared to the intercalated nanocomposites. T_g of ABS is unaffected by incorporation of the silicate filler in its matrix upto 4 wt % loading for different aspect ratios and organic modifications. A significant improvement in the onset of thermal decomposition (40–44°C at 4 wt % organoclay) is seen. The Young's modulus shows improvement, the elongation‐at‐break shows reduction, and the tensile strength shows improvement. Notched and unnotched impact strength of the intercalated MMT nanocomposites is lower as compared to that of ABS matrix. However, laponite and overexchanged organomontmorillonite clay lead to improvement in ductility. For the MMT clays, the Young's modulus (E) correlates with the intercalation change in organoclay interlayer separation (Δd₀₀₁) as influenced by the chemistry of the modifier. Although ABS‐laponite composites are exfoliated, the intercalated OMMT‐based nanocomposites show greater improvement in modulus. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of poly(urethane‐benzoxazine)/clay hybrid nanocomposites

Poly(urethane‐benzoxazine)/clay hybrid nanocomposites (PU/Pa–OMMTs) were prepared from an in situ copolymerization of a polyurethane (PU) prepolymer and a monofunctional benzoxazine monomer, 3‐phenyl‐3,4‐dihydro‐2H‐1,3‐benzoxazine (Pa), in the presence of an organophilic montmorillonite (OMMT), by solvent method using DMAc. OMMT was made from cation‐exchange of Na‐montmorillonite (MMT) with dodecyl ammonium chloride. The formation of the exfoliated nanocomposite structures of PU/Pa‐OMMT was confirmed by XRD from the disappearance of the peak due to the basal diffraction of the layer‐structured clay found in both MMT and OMMT. DSC showed that, in the presence of OMMT, the curing temperature of PU/Pa lowered by ca. 60°C for the onset and ca. 20°C for the maximum. After curing at 190°C for 1 h, the exothermic peak on DSC disappeared. All the obtained films of PU/Pa–OMMT were deep yellow and transparent. As the content of OMMT increased, both the tensile modulus and strength of PU/Pa–OMMT films increased, while the elongation decreased. The characteristics of the PU/Pa–OMMT films changed from plastics to elastomers depending on OMMT content and PU/Pa ratio. PU/Pa–OMMT films also exhibited excellent resistance to the solvents such as tetrahydrofuran, N,N‐dimethylformamide and N‐methyl‐2‐pyrrolidinone. The thermal stability of PU/Pa were enhanced remarkably even with small amount of OMMT. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 4075–4083, 2003     

Crystallization kinetics of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/clay nanocomposites

The preparation and properties of nanocomposites, consisting of a poly(3‐Hydroxybutyrate‐co‐3‐hydroxyvalerate) and an organophilic clay are described. The effect of organophilic clay on the crystallization behavior of (PHBV) was studied. A differential scanning calorimeter (DSC) was used to monitor the energy of the crystallization process from the melt. During the crystallization process from the melt, the organophilic clay led to an increase in crystallization temperature (T_c) of PHBV compared with that for plain PHBV. During isothermal crystallization, dependence of the relative degree of crystallization on time was described by the Avrami equation. The addition of organophilic clay caused an increase in the overall crystallization rate of PHBV, but did not influence the mechanism of nucleation, and growth of the PHBV crystals and the increase caused by a small quantity of clay is move effective than that large one. The equilibrium melting temperature of PHBV was determined as 186°C. Analysis of kinetic data according to nucleation theories showed that the increase in crystallization rate of PHBV in the composite is due to the decrease in surface energy of the extremity surface. The mechanical test shows that the tensile strength of hybrid increased to 35.6 MPa, which is about 32% higher than that of the original PHBV with the incorporation of 3 wt % clay, and the tensile modulus was also increased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 655–661, 2004     

High‐temperature‐resistant polyimide/montmorillonite nanocomposite foams by solid blending

A series of high‐temperature‐resistant polyimide/montmorillonite (PI/MMT) nanocomposite foams were prepared by solid blending method. The dispersion of MMT and effects of MMT content on the properties of the PI/MMT nanocomposite foams were investigated. Results indicated that MMT could be exfoliated effectively and dispersed uniformly in the PI matrix by the solid blending method. The introduction of MMT could considerably increase the reduced compressive strength, thermal resistance, and decrease the dielectric constant of the PI/MMT nanocomposite foams. The reduced compressive strength of nanocomposite foams showed a maximum value at the MMT content of 5 wt%, which was 197% higher than that of pure PI foams. It was worth noting that a significant increase in glass‐transition temperature (T _g) could be achieved with the increase of MMT content, and the maximum T _g was as high as 436°C at the MMT content of 7 wt%. This study may provide a useful method to prepare PI/MMT nanocomposite foams with improved properties for targeted high‐temperature applications. POLYM. ENG. SCI., 2011. ©2011 Society of Plastics Engineers     

Phosphonium‐based layered silicate—Poly(ethylene terephthalate) nanocomposites: Stability,thermal and mechanical properties

PET‐clay nanocomposites were prepared using alkyl quaternary ammonium and phosphonium modified clays by melt‐mixing at 280°C using a micro twin screw extruder. The latter clays were prepared by synthesizing phosphonium surfactants using a simple one‐step method followed by a cation exchange reaction. The onset temperature of decomposition (T_onset) for phosphonium clays (>300°C) was found to be significantly higher than that of ammonium clays (around 240°C). The clay modified with a lower concentration (0.8 meq) of phosphonium surfactant showed a higher T_onset as compared to the clay modified with a higher concentration (1.5 meq) of surfactants. Nanocomposites prepared with octadecyltriphenyl phosphonium (C18P) modified clay showed a higher extent of polymer intercalation as compared with benzyltriphenylphosphonium (BTP) and dodecyltriphenylphosphonium (C12P) modified clays. The nanocomposites prepared with ammonium clays showed a significant decrease in the molecular weight of PET during processing due to thermal degradation of ammonium surfactants. This resulted in a substantial decrease in the mechanical properties. The molecular weight of PET was not considerably reduced during processing upon addition of phosphonium clay. The nanocomposites prepared using phosphonium clays showed an improvement in thermal properties as compared with ammonium clay‐based nanocomposites. T_onset increased significantly in the phosphonium clay‐based nanocomposites and was higher for nanocomposites which contained clay modified with lower amount of surfactant. The tensile strength decreased slightly; however, the modulus showed a significant improvement upon addition of phosphonium clays, as compared with PET. Elongation at break decreased sharply with clay. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Nanostructure and viscoelasticity of layered silicate nanocomposite–electrolyte supports

There is the need for novel polyelectrolytes with enhanced thermal and mechanical properties. In this report, we have reinforced a polyelectrolyte based on poly(dimethylaminoethylmethacrylate) (PDMAEM) using nanoclay montmorillonite (MMT), and have studied the thermal and viscoelastic properties. The protonated polymer (PDMAEMH) was solution mixed with functionalized MMT. Recognizing that the sort of surfactant may have a profound influence on the physical properties of the polymer matrix, neat MMT, and MMT treated with different surfactants (sulfobetaine and ammonia) were used, and the concentration of the nanofiller was varied from 1 to 5%w/w. Strikingly, while PDMAEM exhibited a glass transition temperature T_g of 32°C, the protonated PDMAEMH showed T_g = 155°C. Master curves obtained by applying the time‐temperature superposition principle showed that PDMAEM behaved predominantly elastic (G″ < G′) suggesting an entangled polymer melt. However, PDMAEMH exhibited much longer relaxation times, a shift of ca. seven decades in frequency, suggesting that ionic interactions significantly hampered the molecular dynamics. X‐ray scattering demonstrated that lower concentration and sulfobetaine surfactant favored exfoliation whereas ammonia and untreated MMT favored intercalation of the nanoplates. Furthermore, an enhancement in dynamic storage shear modulus was observed for the nanocomposites exhibiting intercalated morphologies relative to those displaying an exfoliated morphology. It is then suggested that the molecular dynamics is further slowed down due to confinement of the macromolecules between the nanoplates. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation,properties, and anticorrosion application of poly(methyl methacrylate)/montmorillonite nanocomposites coating on brass via solution polymerization

The aim of this study is to improve the anticorrosive property of 7Cu3Zn brass. The methyl‐methacrylate (MMA) monomer solution, modified with fluorine radical and silicone, was used as the polymer matrix to mix with the different percentages of modified montmorillonite (MMT) loading and to exfoliate the lamellar structure of MMT on a nanometer scale during the solution polymerization process, and then form a thin nanocomposites coating on brass as a protective layer. The structural characterization was examined using Fourier transform infrared spectroscopy, X‐ray diffraction (XRD), and transmission electron microscope (TEM). The anticorrosive property of nanocomposites was evaluated using potentiodynamics polarization and electrochemical impedance spectra. The results show that the d‐spacing of MMT was increased, and both exfoliation and intercalation microstructure were observed. Moreover, with the MMT loading increase, the appearance of the intercalation microstructure was more remarkable as a result of silicate layers aggregation. The 1.0 wt %‐coated brass coupons presented the optimistic property of anticorrosion, whose oxygen permeability, corrosion current (i_corr), polarization resistance (R_p), and corrosion rate (R_corr) were 3.5 g/(m²°h), 6.86 nA/cm², 5.81 × 10⁵ Ω°cm², and 0.103 × 10^?3 mm/year, respectively. These results indicate that nanocomposites have potential for anticorrosion application. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 4135–4143, 2007     

Thermal transitions and stability of melt mixed TiO2/Poly(L‐lactic acid) nanocomposites

Poly(L‐lactic acid) (PLLA) nanocomposites containing 5, 10, and 20 wt% titanium dioxide (TiO₂), were prepared by mixing in a co‐rotating twin‐screw extruder. By X‐ray diffraction, a transformation of less ordered (α’‐form) to better organized crystalline (α‐form) structure of PLLA was observed with increasing TiO₂ content. Differential scanning calorimetry (DSC) tests revealed that cold crystallization was facilitated, as shown by the decrease of cold crystallization temperature (T_cc). The main melting peak of PLLA phase in nanocomposites, shifted towards higher temperatures and a shoulder appeared in the lower temperature flank of the curve, revealing a second peak for 20/80 w/w TiO₂/PLLA nanocomposites. The effect of TiO₂ on the isothermal crystallization of PLLA, in the temperature range T_ic: 100–120°C, was also investigated by DSC. At lower temperatures (T_ic: 100 and 110°C), the effect of TiO₂ nanoparticles is an increase of the crystallization rate, leading to lower time for the completion of crystallization, in comparison with that of pure PLLA. The inverse effect was observed at higher crystallization temperatures (T_ic: 115 and 120°C). The kinetic analysis of the crystallization behavior of the examined nanocomposites fits the Avrami equation quite well and gives values for exponent (n) varying between 2 and 3, suggesting a spherulitic crystalline morphology. POLYM. ENG. SCI., 59:704–713, 2019. © 2018 Society of Plastics Engineers     

Preparation and characterization of polystyrene–clay nanocomposites by free‐radical polymerization

The polymerizable cationic surfactant, vinylbenzyldimethylethanolammouium chloride (VBDEAC), was synthesized to functionalize montmorillonite (MMT) clay and used to prepare exfoliated polystyrene–clay nanocomposites. The organophilic MMT was prepared by Na⁺ exchanged montmorillonite and ammonium cations of the VBDEAC in an aqueous medium. Polystyrene–clay nanocomposites were prepared by free‐radical polymerization of the styrene containing intercalated organophilic MMT. Dispersion of the intercalated montmorillonite in the polystyrene matrix determined by X‐ray diffraction reveals that the basal spacing is higher than 17.6 nm. These nanocomposites were characterized by differential scanning calorimetry (DSC), transmission electron micrograph (TEM), thermal gravimetric analysis (TGA), and mechanical properties. The exfoliated nanocomposites have higher thermal stability and better mechanical properties than the pure polystyrene. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1370–1377, 2002