XPS study of Li ion intercalation in V2O5 thin films prepared by thermal oxidation of vanadium metal

The intercalation and deintercalation mechanisms of lithium into V₂O₅ thin films prepared by thermal oxidation of vanadium metal have been studied by X-ray photoelectron spectroscopy (XPS) using a direct anaerobic and anhydrous transfer from the glove box (O₂ and H₂O < 1ppm), where the samples were electrochemically treated, to the XPS analysis chamber. Vanadium in the as-prepared oxide films is mostly (from 93 to 96% depending on samples) in a pentavalent state (V⁵⁺) with a stoichiometric O/V concentration ratio fitting that of V₂O₅. Four to seven percent of VO₂ is also observed. After the 1st and the 2nd intercalation steps at E = 3.3 and 2.8 V versus Li/Li⁺, respectively, the V2p core level spectra evidence a partial reduction to V⁴⁺ states with a remaining concentration of 73 and 56% of V⁵⁺, in agreement with the intercalation of about 1/2 mol of Li per V₂O₅ mol at each intercalation step. Intercalated lithium was observed at a binding energy of 56.1 eV for Li1s. Changes of the electronic structure of the V₂O₅ thin film after intercalation are evidenced by the observation, at a binding energy of 1.3 eV, of occupied V3d states (V⁴⁺) originally empty in the pristine film (V⁵⁺). The V2p and Li1s core level spectra show that the process of Li intercalation is partially irreversible. In the first cycle, 34 and 14% of the vanadium ions remain in the V⁴⁺ state after deintercalation at E = 3.4 and 3.8 V versus Li/Li⁺, respectively, indicating a partially irreversible process already after the 1st deintercalation. The analyses of C1s and O1s XP spectra show the formation of a solid-electrolyte interface (SEI). The analyzed surface layer includes lithium carbonate and Li-alkoxides.     

Li6V10O28, a novel cathode material for Li-ion battery

A novel cathode material, lithium decavanadate Li₆V₁₀O₂₈ with a large tunnel within the framework structure for lithium ion battery has been prepared by hydrothermal synthesis and annealing dehydration treatment. The structure and electrochemical properties of the sample have been investigated. The novel material shows good reversibility for Li⁺ insertion/extraction and long cycle life. High discharge capacity (132 mAh/g) is obtained at 0.2 mA/cm² discharge current and potential range between 2.0 and 4.2 V versus Li⁺/Li. AC impedance of the Li/Li₆V₁₀O₂₈ cell reveals that the cathode process is controlled mainly by Li⁺ diffusion in the active material. The novel material would be a promising cathode material for Li-ion batteries.     

Lithium insertion property of Li2 2V2O5·nH2O

Lithium vanadium oxides have been prepared by the new solution processing in an aqueous hydrogen peroxide solution with lithium and vanadium alkoxides, LiO-n-C₃H₇ and VO(O-i-C₃H₇)₃, at low temperature, compared with conventional high temperature solid state reaction. Oxides having a layered structure isomorphic to that of γ-phase Li_xV₂O₅ were obtained. This “γ-like phase” oxide can be obtained at the nominal Li/V ratio of 1.5 almost as a single phase. However, formation of ω phase cannot be confirmed. The γ-like phase oxide contained water and organic compounds, and the water content n in Li_xV₂O₅·nH₂O was found to be about 2.4 for the γ-like phase oxide. Further as the result of the atomic absorption spectrometric method, the lithium content x in Li_xV₂O₅·nH₂O was estimated to be 2.2, and water molecules presumably exist in the interlayer space.Water content of the γ-like phase oxides, affects charge and discharge behaviours markedly. The lithium extraction-insertion capacity of the γ-like phase oxides were smaller, but the oxides had higher average potential compared with those of γ-phase oxide. As water content of γ-like phase oxides decreased, the lithium extraction-insertion capacity increased. Moreover, it should be noted that the average potential of γ-like phase oxides is at least 1 V higher than that of γ-LiV₂O₅.     

XPS, time-of-flight-SIMS and polarization modulation IRRAS study of Cr2O3 thin film materials as anode for lithium ion battery

Ultra-thin Cr₂O₃ films (12.0, 17.3 and 29.6 nm thick) were produced on Cr metal by thermal oxidation, and their electrochemical properties in 1 M LiClO₄ in propylene carbonate (PC) were investigated by cyclic voltammetry and chronopotentiometry. The reductive electrolyte decomposition and the conversion/deconversion process were observed and analyzed by X-ray photoelectron spectroscopy (XPS), polarization modulation infrared reflection absorption spectroscopy (PM-IRRAS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The initial irreversible capacity due to the reduction of electrolyte and the incomplete deconversion process during the first cycle is 70% of the first discharge capacity. A stable charge/discharge capacity of 460 mAh g⁻¹ was obtained in the 3rd to 10th cycles. XPS and PM-IRRAS evidenced the growth of a solid electrolyte interphase (SEI) layer that is constituted of Li₂CO₃ formed by reductive decomposition of the electrolyte. The SEI layer thickness and/or density is modified by the conversion/deconversion reaction. ToF-SIMS evidenced the volume expansion/shrink resulting from the conversion/deconversion reaction. ToF-SIMS also revealed an incomplete conversion process limited by mass transport, which partitions the oxide into a converted outer part assigned to Li₂O containing Cr traces and an unconverted inner part ascribed to Cr₂O₃ or lower Cr oxide containing Li. It was found that the deconversion re-homogenizes the oxide film in a single layer but with lithium trapped in it. The present study provides a detailed understanding of the interfacial reaction on the oxide anode undergoing a conversion/deconversion reaction.     

Rheological phase reaction synthesis and electrochemical performance of Li3V2(PO4)3/carbon cathode for lithium ion batteries

Monoclinic lithium vanadium phosphate/carbon (Li₃V₂(PO₄)₃/C) cathode has been synthesized for applications in lithium ion batteries, via a rheological phase reaction (RPR) method. The sample is characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). This material exhibits high initial discharge capacity of 189 and 177 mAh g⁻¹ at 0.1 and 0.2 C between 3.0 and 4.8 V, respectively. Moreover, it displays good fast rate performance, which discharge capacities of 140, 133, 129 and 124 mAh g⁻¹ can be delivered after 100 cycles between 3.0 and 4.8 V vs. Li at a different rate of 0.5, 1, 2 and 5 C, respectively. The electrochemical impedance spectroscopy (EIS) is also investigated.     

Li-intercalation behaviour of vanadium oxide thin film prepared by thermal oxidation of vanadium metal

In order to produce thin films of crystalline V₂O₅, vanadium metal was thermally oxidised at 500 °C under oxygen pressures between 250 and 1000 mbar for 1-5 min. The oxide films were characterised by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), X-ray diffraction (XRD) and Rutherford backscattering spectrometry (RBS). The lithium intercalation performance of the oxide films was investigated by cyclic voltammetry (CV), chronopotentiometry and electrochemical impedance spectroscopy (EIS). It was shown that the composition, the crystallinity and the related lithium intercalation properties of the thin oxide films were critically dependent on the oxidation conditions. The formation of crystalline V₂O₅ films was stimulated by higher oxygen pressure and longer oxidation time. Exposure for 5 min at 750 mbar O₂ at 500 °C resulted in a surface oxide film composed of V₂O_5, and consisting of crystallites up to 200 nm in lateral size. The thickness of the layer was about 100 nm. This V₂O₅ oxide film was found to have good cycling performance in a potential window between 3.8 and 2.8 V, with a stable capacity of 117 ± 10 mAh/g at an applied current density of 3.4 μA/cm². The diffusion coefficients corresponding to the two plateaus at 3.4 and 3.2 V were determined from the impedance measurements to (5.2 and 3.0) × 10⁻¹³ cm² s⁻¹, respectively. Beneath the V₂O₅ layer, lower oxides (mainly VO₂) were found close to the metal. At lower oxygen pressure and shorter exposure times, the oxide films were less crystalline and the amount of V⁴⁺ increased in the surface oxide film, as revealed by XPS. At intermediate oxygen pressures and exposure times a mixture of crystalline V₂O₅ and V₆O₁₃ was found in the oxide film.     

Mixed oxides Ca2Fe2O5 and Ca2Co2O5 as anode materials for Li-ion batteries

The electrochemical performance of mixed oxides, Ca₂Fe₂O₅ and Ca₂Co₂O₅ for use in Li-ion batteries was studied with Li as the counter electrode. The compounds were prepared and characterized by X-ray diffraction and SEM. Ca₂Fe₂O₅ showed a reversible capacity of 226 mAh/g at the 14th cycle and retained 183 mAh/g at the end of 50 cycles at 60 mA/g in the voltage window 0.005-2.5 V. A reversible capacity in the range, 365-380 mAh/g, which is stable up to 50 charge-discharge cycles is exhibited by Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V and at 60 mA/g. This corresponds to recycleable moles of Li of 3.9±0.1 (theoretical: 4.0). Significant improvement in the cycling performance and attainable reversible capacity were noted for Ca₂Co₂O₅ on cycling to an upper cut-off voltage of 3.0 V as compared to 2.5 V. Coulombic efficiency for both compounds is >98%. Electrochemical impedance spectroscopy (EIS) data clearly indicate the reversible formation/decomposition of polymeric surface film on the electrode surface of Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V. Cyclic voltammetry results compliment the galvanostatic cycling data.     

Preparation of micro-dot electrodes of LiCoO2 and Li4Ti5O12 for lithium micro-batteries

Fabrications of micro-dot electrodes of LiCoO₂ and Li₄Ti₅O₁₂ on Au substrates were demonstrated using a sol-gel process combined with a micro-injection technology. A typical size of prepared dots was about 100 μm in diameter, and the dot population on the substrate was 2400 dots cm⁻². The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were characterized with scanning electron microscopy, X-ray diffraction, micro-Raman spectroscopy, and cyclic voltammetry. The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were evaluated in an organic electrolyte as cathode and anode for lithium micro-battery, respectively. The LiCoO₂ micro-dot electrode exhibited reversible electrochemical behavior in a potential range from 3.8 to 4.2 V versus Li/Li⁺, and the Li₄Ti₅O₁₂ micro-dot electrode showed sharp redox peaks at 1.5 V.     

Electrochemical performance of the carbon coated Li3V2(PO4)3 cathode material synthesized by a sol-gel method

A carbon coated Li₃V₂(PO₄)₃ cathode material for lithium ion batteries was synthesized by a sol-gel method using V₂O₅, H₂O₂, NH₄H₂PO₄, LiOH and citric acid as starting materials, and its physicochemical properties were investigated using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDAX), transmission electron microscope (TEM), and electrochemical methods. The sample prepared displays a monoclinic structure with a space group of P2₁/n, and its surface is covered with a rough and porous carbon layer. In the voltage range of 3.0-4.3 V, the Li₃V₂(PO₄)₃ electrode displays a large reversible capacity, good rate capability and excellent cyclic stability at both 25 and 55 °C. The largest reversible capacity of 130 mAh g⁻¹ was obtained at 0.1C and 55 °C, nearly equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). It was found that the increase in total carbon content can improve the discharge performance of the Li₃V₂(PO₄)₃ electrode. In the voltage range of 3.0-4.8 V, the extraction and reinsertion of the third lithium ion in the carbon coated Li₃V₂(PO₄)₃ host are almost reversible, exhibiting a reversible capacity of 177 mAh g⁻¹ and good cyclic performance. The reasons for the excellent electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ cathode material were also discussed.     

Crystal structure and electrochemical performance of Li3V2(PO4)3 synthesized by optimized microwave solid-state synthesis route

To investigate the crystal structure and electrochemical performance of samples synthesized under different microwave solid-state synthesis condition, a series of Li₃V₂(PO₄)₃ samples has been synthesized at five different temperatures for 3-5 min and at 750 °C for various time. The as-synthesized Li₃V₂(PO₄)₃ samples are characterized and studied by ICP-AES analysis, X-ray diffraction (XRD), Rietveld analysis, scanning and transmission electron microcopy (SEM and TEM). At relatively lower temperature (650 °C) and very short reaction time (3 min), pure phase of Li₃V₂(PO₄)₃ could be synthesized in microwave irradiation field. The crystal structure and Li atomic fractional coordinate present a significant deviation upon the change of microwave irradiation temperature and time. Relatively, the diffusion ability of lithium cations and the electrochemical performance are affected. Under the proper reaction temperature and time, the carbon-free samples MW750C5m and MW850C3m show the best specific discharge capacity 126.4 and 132 mAh g⁻¹ at the voltage range of 3.0-4.3 V, near the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). At the voltage range of 3-4.8 V, the sample MW750C5m presents the best initial specific charge capacity of 197 mAh g⁻¹, equivalent to the reversible cycling of three lithium ions per Li₃V₂(PO₄)₃ formula unit (197 mAh g⁻¹). The initial discharge capacity, the samples MW750C5m and MW850C3m present high specific discharge capacity 183.4 and 175.7 mAh g⁻¹, respectively. The relationship among microwave irradiation condition, crystal structure, lithium atomic fractional coordinates and the electrochemical performance have been discussed in detail.     

A kinetic study of electrochemical lithium insertion into oriented V2O5 thin films prepared by rf sputtering

The kinetics of the electrochemical lithium insertion reaction in crystalline V₂O₅ thin films in liquid electrolyte has been investigated using ac impedance spectroscopy. The experimental data are obtained for sputtered films characterized by a common morphology corresponding to an arrangement of V₂O₅ platelets perpendicular to the substrate (h 0 0 or 1 1 0 preferred orientation). The results are discussed as a function of the Li content for 0 < x < 1 in Li_xV₂O₅, the film thickness in the range of 0.6-3.6 μm and temperature 15-55 °C. The moderate evolution of the chemical diffusion coefficient D vs. the lithium content is related with the specific structural response of these pure thin film materials which exhibit a single phase behavior. A comparison of the kinetic parameters for different thickness values allows to indicate the same Li diffusion rate whatever the film thickness and the diffusion pathway does not correspond to the thickness but to the length of the edge (≈1 μm) of V₂O₅ platelets. For the first time, an experimental evaluation of the activation energy for Li diffusion in crystalline V₂O₅ is obtained. A value of 0.98 eV is found for a diffusion phenomenon along the b direction. This work demonstrates the excellent capacity-rate performance as well as the efficient and homogeneous behavior of these oriented films can be explained by their specific microstructure.     

Atomic force microscopy studies of surface and dimensional changes in LixCoO2 crystals during lithium de-intercalation

An in situ electrochemical atomic force microscopy (EC-AFM) cell was developed to study surface and dimensional changes of individual Li_xCoO₂ crystals during lithium de-intercalation. Discrete Li₂CO₃ particles having 50-250 nm in diameter and 5-15 nm in height were observed on the surface of stoichiometric LiCoO₂ crystals and they were shown to gradually dissolve into the LiPF₆-containing electrolyte. The dimensional change of individual Li_xCoO₂ crystals along the c_hex. axis was monitored in situ during lithium de-intercalation. Evidence of surface instability or structural instability was not found in Li_xCoO₂ single crystals upon de-intercalation to 4.2 V versus Li.     

A delithiated LiNi0.65Co0.25Mn0.10O2 electrode material: A structural, magnetic and electrochemical study

A crystalline LiNi_0.65Co_0.25Mn_0.10O₂ electrode material was synthesized by the combustion method at 900 °C for 1 h. Rietveld refinement shows less than 3% of Li/Ni disorder in the structure. Lithium extraction involves only the Ni²⁺/Ni⁴⁺ redox couple while Co³⁺ and Mn⁴⁺ remain electrochemically inactive. No structural transition was detected during cycling in the whole composition range 0 < x < 1.0. Furthermore, the hexagonal cell volume changes by only 3% when all lithium was removed indicating a good mechanical stability of the studied compound. LiNi_0.65Co_0.25Mn_0.10O₂ has a discharge capacity of 150 mAh/g in the voltage range 2.5-4.5 V, but the best electrochemical performance was obtained with an upper cut-off potential of 4.3 V. Magnetic measurements reveal competing antiferromagnetic and ferromagnetic interactions - varying in strength as a function of lithium content - yielding a low temperature magnetically frustrated state. The evolution of the magnetic properties with lithium content confirms the preferential oxidation of Ni ions compared to Co³⁺ and Mn⁴⁺ during the delithiation process.     

Lithium insertion/deinsertion properties of new layered vanadium oxides obtained by oxidation of the precursor H2V3O8

The electrochemical behavior of the three new vanadium oxides M_yH_1−yV₃^VO₈ (M=Li, Na, K; y=0.6-0.9) towards lithium insertion was studied. For each compound, the main insertion phenomena, and the lithium amount which can be inserted, were determined from galvanostatic studies performed at different rates. In order to better explain the differences between the compounds, the galvanostatic intermittent titration technique was used and chronoamperometry experiments were performed. Cyclability studies have shown that the performances of M_0.6H_0.4V₃O₈ (M=Li, K) are not better than those of H₂V₃O₈. On the contrary, Na_0.9H_0.1V₃O₈ presents very interesting lithium insertion properties, with a specific capacity of 215 mAh g⁻¹ in the 1.5-4 V voltage range at C/10, and a capacity loss at the 40th cycle remaining smaller than 2.5%. Na_0.9H_0.1V₃O₈ is therefore a good candidate as positive electrode material for rechargeable lithium batteries.     

Structural and electrochemical behaviors of metastable Li2/3[Ni1/3Mn2/3]O2 modified by metal element substitution

Layered metastable lithium manganese oxides, Li_2/3[Ni_1/3−xMn_2/3−yM_x+y]O₂ (x = y = 1/36 for M = Al, Co, and Fe and x = 2/36, y = 0 for M = Mg) were prepared by the ion exchange of Li for Na in P2-Na_2/3[Ni_1/3−xMn_2/3−yM_x+y]O₂ precursors. The Al and Co doping produced the T^#2 structure with the space group Cmca. On the other hand, the Fe and Mg doped samples had the O6 structure with space group R-3m. Electron diffraction revealed the 1:2 type ordering within the Ni_1/3−xMn_2/3−yM_x+yO₂ slab. It was found that the stacking sequence and electrochemical performance of the Li cells containing T^#2-Li_2/3[Ni_1/3Mn_2/3]O₂ were affected by the doping with small amounts of Al, Co, Fe, and Mg. The discharge capacity of the Al doped sample was around 200 mAh g⁻¹ in the voltage range between 2.0 and 4.7 V at the current density of 14.4 mA g⁻¹ along with a good capacity retention. Moreover, for the Al and Co doped and undoped oxides, the irreversible phase transition of the T^#2 into the O2 structure was observed during the initial lithium deintercalation.     

Microwave solid-state synthesis and electrochemical properties of carbon-free Li3V2(PO4)3 as cathode materials for lithium batteries

Monoclinic Li₃V₂(PO₄)₃ can be rapidly synthesized at 750 °C for 5 min (MW5m) by using microwave solid-state synthesis method. The refined cell parameters and atomic coordination of the sample MW5m show some deviations compared with those of the sample synthesized in conventional solid-state synthesis method, especially the coordinate of Li atoms. Compared with the electrochemical properties of the carbon-coating sample Li₃V₂(PO₄)₃, the carbon-free sample MW5m presents well electrochemical properties. In the cut-off voltage of 3.0-4.3 V, MW5m sample presents a specific charge capacity of 132 mAh g⁻¹, almost equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹), and specific discharge capacity of 126.4 mAh g⁻¹. In the cut-off voltage of 3.0-4.8 V, MW5m shows an initial specific discharge capacity of 183.4 mAh g⁻¹ at 0.1 C, near the theoretical discharge capacity. In the cycle performance, the capacity fade of Li₃V₂(PO₄)₃ is dependent on the cut-off voltage and the preparation method, more capacity lost at relatively higher charge/discharge voltage. The reasons for the excellent electrochemical properties of Li₃V₂(PO₄)₃ rapidly synthesized in microwave field are discussed in detail.     

Electrochemical properties of microwave irradiated synthesis of poly(3,4-ethylenedioxythiophene)/V2O5 nanocomposites as cathode materials for rechargeable lithium batteries

A series of poly(3,4-ethylenedioxythiophene) (PEDOT)/V₂O₅ nanocomposites are prepared via the redox intercalative polymerization reaction of 3,4-ethylenedioxythiophene (EDOT) monomer and crystalline V₂O₅ within 10 min by using rapid 2.45 GHz microwave irradiation with full power (800 W). The unique properties of the resultant nanocomposites are investigated by various characterization techniques using powder XRD, TGA/DTA and four-point probe conductivity analysis supports the intercalation of polymer nanosheet between V₂O₅ layers leading to enhanced bi-dimensionality. X-ray photoelectron spectroscopy analysis clearly shows the presence of mixed valent V⁴⁺/V⁵⁺ in the V₂O₅ framework after the redox intercalative polymerization which also confirms charge transfer from the polymer to the V₂O₅ framework. The application potential of these composites as cathode materials in rechargeable lithium batteries is also demonstrated by the electrochemical intercalation of lithium into the PEDOT/V₂O₅ nanocomposites, where an enhancement in the discharge capacity (370 mAh/g) is observed compared to that of crystalline V₂O₅.     

In situ XAS investigation of the oxidation state and local structure of vanadium in discharged and charged V2O5 aerogel cathodes

We have examined the evolution of the oxidation state and atomic structure of vanadium(V) in discharged and charged nanophase vanadium pentoxide (V₂O₅) aerogel cathodes under in situ conditions using X-ray absorption spectroscopy (XAS). We show that the oxidation state of V in V₂O₅ aerogel cathode heated under vacuum (100 μTorr) at 220 °C for 20.5 h is similar to that of V in a commercially obtained sample of orthorhombic V₂O₅. In addition, lithium (Li) insertion during the first cycle of discharging leads to the reduction of V(V) to V(IV) and V(IV) to V(III) in a manner consistent with the stoichiometry of the sample (i.e. Li_xV₂O₅). Li extraction during charging leads to oxidation of V(III) to V(IV) and then V(IV) to V(V). Furthermore, the oxidation state of V in fully charged cathodes remains unchanged with cycling (upto at least the 16th cycle) from that of V in the control V₂O₅ aerogel cathode. However, the average oxidation state of V in discharged V₂O₅ cathodes increased with cycling. Moreover, the local structure of V in the discharged state has a higher degree of symmetry than that of the fully charged state. A significant change in the structure of the VV correlation of discharged cathodes is observed with cycling indicating the formation of electrochemically irreversible phases.     

A kinetic study of lithium transport in the sol–gel Cr0.11V2O5.16 mixed oxide

The kinetics of the electrochemical lithium insertion reaction in the sol–gel chromium–vanadium mixed oxide Cr_0.11V₂O_5.16 has been investigated using ac impedance spectroscopy. The chemical lithium diffusion coefficient is found to be in the range 10⁻⁸/10⁻¹² cm²/s depending the Li content over the wide Li composition range 0 < x < 2 in Li_xCr_0.11V₂O_5.16. The evolution of the cathode impedance is investigated as a function of the lithium content and cycles. The results are discussed in relation with the cycling properties of the electrode material and the unusual structural response of the sol–gel mixed oxide which consists of a single phase behaviour with a continuous cell volume expansion of 6–7% in the 0 < x < 2 range for Li_xCr_0.11V₂O_5.16. For x < 1, a comparison with available kinetic data for the parent oxide indicates a very close behaviour. Cr_0.11V₂O_5.16 is shown to be the best V₂O₅-based cathode material with an initial specific capacity of 280 mAh/g at C/10 rate and still 240 mAh/g after 50 cycles in the 3.8–2 V potential range. The present kinetic data seem to indicate its better cycling behaviour mainly originates from its specific structural response rather than from kinetic reasons.     

Effect of synthesis condition on the structural and electrochemical properties of Li[Ni1/3Mn1/3Co1/3]O2 prepared by the metal acetates decomposition method

In order to get homogeneous layered oxide Li[Ni_1/3Mn_1/3Co_1/3]O₂ as a lithium insertion positive electrode material, we applied the metal acetates decomposition method. The oxide compounds were calcined at various temperatures, which results in greater difference in morphological (shape, particle size and specific surface area) and the electrochemical (first charge profile, reversible capacity and rate capability) differences. The Li[Ni_1/3Mn_1/3Co_1/3]O₂ powders were characterized by means of X-ray diffraction (XRD), charge/discharge cycling, cyclic voltammetry and SEM. XRD experiment revealed that the layered Li[Ni_1/3Mn_1/3Co_1/3]O₂ material can be best synthesized at temperature of 800 °C. In that synthesized temperature, the sample showed high discharge capacity of 190 mAh g⁻¹ as well as stable cycling performance at a current density of 0.2 mA cm⁻² in the voltage range 2.3-4.6 V. The reversible capacity after 100 cycles is more than 190 mAh g⁻¹ at room temperature.