The role of ε-martensite in the impact toughness of an Fe-17Mn alloy

The influence of -martensite on the cryogenic toughness of an Fe-17 wt% Mn alloy was studied in this work. Alloys were tempered at various temperatures in order to systematically increase the volume fraction of -martensite. This was followed by Charpy impact testing conducted at room temperature and at–196°C. The experimental results indicated that although room-temperature toughness was not influenced by the -martensite content, the cryogenic toughness was strongly dependent on the volume fraction of -martensite. In particular, with the exception of the alloys tempered at 400 and 450°C, the impact toughness consistently increased with -martensite content. Microstructural and fractographic evaluations using SEM and TEM suggested that the toughness improvements were attributed to the stress-induced martensite transformation. No microstructural evidence was found which could be ascribed to an effect of -martensite on the low-temperature embrittlement exhibited by Fe-Mn alloys tempered at 400–450°C.     

The dielectric properties of glass-ceramic-on-metal substrates for microelectronics packaging

The dielectric properties of some glass-ceramic-on-metal substrates have been determined over the frequency range 500 Hz to 5 MHz using a.c. bridge techniques. The substrates consisted of cordierite-based glass-ceramics screen printed on molybdenum. For glass layers of thickness greater than 100 m both the permittivity, and the dielectric loss, , are frequency independent over this frequency range at room temperature giving the value of =6.5 and tan =8×10^–3; the room-temperature data are consistent with the universal law of dielectric response. The variation of permittivity with temperature has also been examined and, below 120 °C, the temperature coefficient [(–1) (+2)]^–1 (/T)_p, was found to be 1.3×10^–5 K^–1. The results are compared with those previously reported for Al₂O₃ and AIN substrates.     

On the analysis of tunneling data for A15 superconductors

We examine the applicability of the standard McMillan inversion of Eliashberg's equations for superconductors with a nonconstant electronic density of statesN(). We do this usign simple models forN() and a realistically shapedN() taken from recent band structure work for Nb₃Sn. It turns out that peak structure inN() near _F may lead to gross errors in the derived Eliashberg function ²F() when the energy dependence ofN() is omitted in the inversion procedure. For Nb₃Sn, this leads to a 40% overestimate of when ²F() is evaluated via the standard McMillan program.     

Heat exchange in two-phase flow about a surface located in a rectangular channel

Similitude equations are obtained on the basis of the principle of superposition of separate effects to calculate heat exchange between surfaces with complexshaped cross sections located in a rectangular channel during their cooling by a two-phase flow.Notation T, q temperature and heat flux - T_w mean surface temperature - I, R current and electrical resistance - V volume of the material - , , anda heat-transfer coefficients, thermal conductivity, and linear expansion of the material - relative functions - =_m; ^* = _m ^{* *} _s ^* ; temperature factor - X relative weight content of liquid phase Indices w surface - f incoming flow - v volume - m two-phase flow - angle of attack - s shape of surface - * pertains to surface with swirl vanes Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 40, No. 5, pp. 780–786, May, 1980.     

Study of the paramagnetic-antiferromagnetic transition and the γ → ε martensitic transformation in Fe-Mn alloys

The paramagnetic-antiferromagnetic transition and the martensitic transformation of Fe-Mn (Mn 15–32 wt%) alloys have been investigated by resistivity, dilatometry and X-ray diffraction (XRD). The results show that paramagnetic-antiferromagnetic transition increases the resistivity and the volume of alloys, whereas the martensitic transformation reduces the resistivity and volume of alloys. The A _f that was determined by the dilatometric method is not the temperature that martensites in the Fe-Mn alloys have reverse transformed to austenites completely. Mn additions reduce M _s, increase T _N and the lattice parameter of austenite in the Fe-Mn alloys. Both the antiferromagnetic transition and the martensitic transformation lead to an increase in the lattice parameter of austenite. The lattice parameters both above T _N and below T _N decrease linearly with temperature. The lattice parameter below M _s increases first and then decreases. Moreover, the (110) and (002) atomic planes in the Fe-15Mn-0.15C alloy are separated into two peaks: 2 for (002) is 44.16°, 2 for (110) is 44.47°.     

Aligned microstructure of some particulate polymer composites obtained with an electric field

Alignment by an electric field was obtained for a variety of particles dispersed in photopolymerizable fluids. The particle shapes studied were irregular, spherical, rhombohedral, rod-like (fibres), and platelet. The sizes ranged from sub-micrometres to tens of micrometres, and the dielectric constants of the particles varied from less than that of the lquid matrix to very much greater than that of the matrix. Polymerization or hardening of the matrix was possible at room temperature, required only a few seconds, and the aligned structures obtained were able to be examined by both light and scanning electron microscopy after fracture or sectioning. Nominally equiaxed particles, containing a statistical proportion of non-equiaxed particles, could be completely aligned at 48 vol% concentration in a fluid having a viscosity of about 2.5 Pa s, but at 57 vol%, the mixture behaved as a paste, and only particle rotation and local rearrangements were possible. The rate of alignment seemed to depend generally on the magnitude of 1(a)2, where 1 is the relative dielectric constant of the liquid resin, a is the particle radius, and is the particle dipole coefficient given by (2–1)/(2+21), where 2 is the relative dielectric constant of the particles. 1(a)2 emphasizes the importance of particle size and the relative unimportance of the particle dielectric constant for alignment, except when 21. Platelets were more rapidly aligned than fibres.     

A method of joint determination of the effective coefficients of horizontal mixing of large particles and of external heat exchange in an organized fluidized bed

A method is proposed for the joint determination of the coefficients of horizontal particle diffusion and external heat exchange in a stagnant fluidized bed.Notation c_f, c_s, c_n specific heat capacities of gas, particles, and nozzle material, respectively, at constant pressure - D effective coefficient of particle diffusion horizontally (coefficient of horizontal thermal diffusivity of the bed) - d equivalent particle diameter - d_t tube diameter - H₀, H heights of bed at gas filtration velocities u₀ and u, respectively - H_a height of active section - l width of bed - L tube length - l _o width of heating chamber - N number of partition intervals - p=H/H₀ expansion of bed - s_n surface area of nozzle per unit volume of bed - S_h, S_v horizontal and vertical spacings between tubes - t_c, t₀, t_s, t_n, t_w initial temperature of heating chamber, entrance temperature of gas, particle temperature, nozzle temperature, and temperature of apparatus walls, respectively - u₀, u velocity of start of fluidization and gas filtration velocity - y horizontal coordinate - ^*, coefficient of external heat exchange between bed and walls of apparatus and nozzle - ₁, ₁, ₂, ... coefficients in (4) - thickness of tube wall - _b bubble concentration in bed - ₀ porosity of emulsion phase of bed - _n porosity of nozzle - =(t_s – t₀)/(t_c – t₀) dimensionless relative temperature of particles - _n coefficient of thermal conductivity of nozzle material - f, _s, _n densities of gas, particles, and nozzle material, respectively - _be=_s(1 – ₀) (1 – _b) average density of bed - time - _max time of onset of temperature maximum at a selected point of the bed - R =l _o/l Fourier number - Pe = ₁ l ²/D Péclet number - Bi = /_n Biot number Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 41, No. 3, pp. 457–464, September, 1981.     

A model with length scales for composites with periodic structure. Steady state heat conduction problem

A new high-order model for analysing distribution of temperature in periodic composites is proposed. The original scalar elliptic problem with Y-periodic coefficients (Y is a cube) is replaced with a vectorial elliptic problem of constant coefficients. The unknown fields are: the averaged distribution of temperature and the vector field which stands for perturbation of the temperature within the cells of periodicity. The recovery of temperature in the original composite is given by the approximation: 0(x)=0(x) +h ^a (x/) _a (x) analogous with the first terms of the two-scale asymptotic expansion known from the homogenization theory. The functions h are defined as approximations of the solutions to the basic cell problems. In contrast to the two-scale expansion the expression for satisfies the boundary condition.     

Effect of crystalline phase, orientation and temperature on the dielectric properties of poly (vinylidene fluoride) (PVDF)

The effect of crystalline phase, uniaxial drawing and temperature on the real () and imaginary () parts of the relative complex permittivity of poly (vinylidene fluoride) (PVDF) was studied in the frequency range between 10² and 10⁶ Hz. Samples containing predominantly and phases, or a mixture of these, were obtained by crystallization from a DMF solution at different temperatures. phase samples were also obtained from melt crystallization and from commercial films supplied by Bemberg Folien. Different molecular orientations were obtained by uniaxial drawing of and phase samples. The results showed that the crystalline phase exerts strong influence on the values of and , indicating that the _a relaxation process, associated with the glass transition of PVDF, is not exclsively related to the amorphous region of the polymer. An interphase region, which maintains the conformational characteristics of the crystalline regions, should influence the process decisively. The molecular orientation increased the values of for both PVDF phases and modified its dependence with temperature over the whole frequency range studied. The influence of the crystallization and molecular orientation conditions on the dc electric conductivity (_dc) were also verified. The value of _dc was slightly higher for samples crystallized from solution at the lowest temperature and decreased with draw ratio.     

Effects of Bonding Configuration and Structural Perfection on the Properties of Doped NaNbO -Based Solid Solutions

The effects of bonding configuration (electronegativity) and doping-produced vacancies on the properties of doped NaNbO₃-based solid solutions were studied. The results demonstrate that there is an average electronegativity of the elements involved above which the uniform distortion parameter increases and the relative dielectric permittivity ^T ₃₃/₀decreases with increasing electronegativity, as is common in other solid-solution systems. Below this value, both and ^T ₃₃/₀vary in the opposite way. An explanation for the anomalous behavior of is proposed.     

The morphology of α′ martensite in a two-phase (α+γ) Fe-Cr-Ni stainless steel

Both lath-shaped and martensites are induced by tensile deformation within of a two-phase ( + ) Fe-Cr-Ni stainless steel, forms from the through the at an intersection of two crystals. These are observed both when is surrounded by and when borders . The amount of strain at which both and nucleate, increases with test temperatures in the range –196 to 50° C. Adjacent laths are either twin-related, or 5, 9, 15 or 19° off the twin relationship, as found by analysing electron diffraction patterns.     

Effect of Gamma Irradiation on the Piezoelectric Properties of K2Sr4Nb10O30–K6Li4Nb10O30 Solid Solutions

The effect of gamma irradiation on the dielectric ( ₃₃/₀, tan) and piezoelectric (d ₃₁, g ₃₁, K _p, Q _m) properties of ₂Sr₄Nb₁₀O₃₀–K₆Li₄Nb₁₀O₃₀ solid solutions (tetragonal tungsten bronze structure) was studied as a function of K₆Li₄Nb₁₀O₃₀ content. The results demonstrate that increasing the gamma dose to 9 × 10⁵ Gy reduces ₃₃/₀ and tan. With increasing Li⁺ content (filling of triangular channels), d ₃₁, g ₃₁, K _p, and Q _m increase. The results are interpreted in terms of the generation of stable defects and effective redistribution of the energy of gamma radiation over the ceramic sample.     

On the resonance of acoustic waves in slightly deformed and slowly moving slabs

The stability is studied of acoustic waves generated by a time harmonic force in slabs described by: 0z1±g(x, y). By using a recently developed method, the exact solution of the Dirichlet problem is found for =0. It is shown that the solution is unstable against values of the frequency: =n,n. This is in agreement with the result already known in the literature, but found by other means. In a slightly deformed slab, 0<1, it is shown that stabilization of the resonant wave occurs at a time of order ^–. This is valid if the upper boundary is a concave surface. In case of a slab with slowly moving upper boundary, only the growth rate of the amplitude of the resonant wave is reduced. This holds for a non-oscillating motion of the upper boundary. In the case of an oscillating motion a further resonance is produced.     

Some electrical characteristics of lithium and yttrium sialons

Some electrical properties of hot-pressed lithium sialons, Li _x/8Si_6–3x/4Al_5x/8O _x N_8–x havingx<5 and an yttrium sialon were measured between 291 and 775 K; the former consisted essentially of a single crystalline phase whereas the latter contained 98% glassy phase. For lithium sialons, the charging and discharging current followed al(t) t ^–nlaw withn=0.8 at room temperature. The d.c. conductivities were about 10^–13 ohm^–1 cm^–1 at 291 K and rose to 5×10^–7 ohm^–1 cm^–1 at 775 K. At high temperatures electrode polarization effects were observed in d.c. measurements. The variation of the conductivity over the frequency range 200 Hz to 9.3 GHz followed the () ⁿ law. The data also fitted the Universal dielectric law,() ^n–1 well, and approximately fitted the Kramers-Kronig relation()/()– =cot (n/2) withn decreasing from 0.95 at 291 K to 0.4 at 775 K. The temperature variations of conductivities did not fit linearly in Arrhenius plots. Very similar behaviour was observed for yttrium sialon except that no electrode polarization was observed. The results have been compared with those obtained previously for pure sialon; the most striking feature revealed being that _d.c. for lithium sialon can be at least 10³ times higher than that of pure sialon. Interpretation of the data in terms of hopping conduction suggests that very similar processes are involved in all three classes of sialon.     

Slip flow past an approximate spheroid

Summary Creeping axisymmetric slip flow past a spheroid whose shape deviates slightly from that of a sphere is investigated. An exact solution is obtained to the first order in the small parameter characterizing the deformation. As an application, the case of flow past an oblate spheroid is considered and the drag experienced by it is evaluated. Special well-known cases are deduced and some observations made.Notation A _n, B_n, C_n, D_n, E_n, F_n, b₂, d₂ Constants - a, b radii of spheres - coefficient of sliding fraction - D drag - , _m parameters characterizing the deformation of the sphere - c a(1+) - viscosity coefficient - - dimensionless coordinate - I _n Gegenbauer function - P _n Legendre function - Stream function - U stream velocity at infinity     

The effect of explosive loading on the microstructure of some metals and alloys

The effects of explosive pulses on the microstructure of Al-4.5% Cu duralumin, tough pitch copper, pure magnetic iron and 18 chromium 8 nickel stainless steel have been studied using transmission electron microscopy. An explosive loading assembly was designed to investigate the effect of both the flanks and the length of shock pulses on the material microstructure. In copper and duralumin it was found that the microhardness increased with the duration of the rarefaction flank. The size of the shock transformed martensite particles in stainless steel also increased with rarefaction time. Three wave interactions could be related to the microstructure of baratol-loaded iron and were attributed to the double shock front caused by the a to phase transformation. Twinning was found to occur when the reflected elastic wave interacted with the first part of the double shock front. The abrupt hardness increase caused by the interaction of the first reflected wave and the second transformation shock front was observed. In addition, a second more gradual hardness increase is attributed to the interaction between the low pressure and the high pressure rarefaction waves which caused a relatively slowly increasing rarefaction shock. The microstructure of shocked stainless steel showed that hexagonal plates and twins could occur in the same grain and that martensite particles were formed at the intersection of two twins, or of plates and twins. Both Kurdjumov-Sachs and Nishyama-Wassermann orientations were observed and sometimes occurred on the same fault band. The short rise and fall times in the pulse flanks made it possible to discuss formation mechanisms for twins and martensite particles in terms of the available formation times.     

Ageing characteristics of cast Zn-Al based alloy (ZnAl7Cu3)

Microstructure and ageing characteristics of a cast Zn-Al based alloy (ZnAl7Cu3) were studied using X-ray diffraction, electron scanning microscopy and back-scattered diffraction techniques. Two stages of phase transformation, i.e., decomposition of zinc rich phase and four phase transformation, + T + , were detected during ageing at 150°C. Electron back-scattered diffraction technique was applied in distinguishing both zinc rich and phases.     

The Possibility of Reproducing the Units of Complex Permittivity at High Frequencies

The results of theoretical investigations of the reproduction of the units of the components of complex permittivity and by a method based on the use of the wave properties of a coaxial line are presented. The errors in reproducing and are analyzed.     

Dielectric Properties of Pb(Ti,Zr)O3–∑n=14 (PbB"1-αB""αO3)nSolid Solutions

Dielectric permittivity measurements in Pb(Ti,Zr)O₃–_n=1 ⁴ (PbB^" _{1 -} B^" O₃) _n solid-solution systems demonstrate that the permittivity ^T ₃₃/₀of the solid solutions correlates with the molar ratio of the more soft-electric to the less soft-electric component of PbB^" _{1 -} B^" O₃(). With increasing , ^T ₃₃/₀rises because of the decrease in the uniform cell distortion parameter. The permittivity is also sensitive to structural disordering at > 1 and reduction in the density of the materials at 1.     

An Improved Transient Calorimetric Technique for Measuring the Total Hemispherical Emittance of Nonconducting Materials (Emittance Evaluation of Glass Sheets)

For measurements of the total hemispherical emittance _h of nonconducting materials, a problem of the thermal gradient produced in a sample specimen arises. An improved transient calorimetric technique to reduce the thermal gradient is proposed in this study. Glass sheets (borosilicate), semi-transparent for radiation, are selected as the nonconducting test material. The _h values of the glass sheets for various thicknesses are measured, and their results are presented as functions of thickness and temperature. The thermal gradients in the specimens are calculated by a three-dimensional analysis, and the corner effect due to them on the measured _h is estimated. It is shown that the proposed technique is useful for measuring the emittance _h of nonconducting materials.