PP/LDPE blends produced by reactive processing. I. Grafting efficiency and rheological and high‐elastic properties of [PP/LDPE]‐g‐IA melts

Itaconic acid (IA) was grafted onto polypropylene/low‐density polyethylene (PP/LDPE) blends. The ratio of polymeric components was varied from 100 : 0 to 0 : 100. The effect of the variation in the ratios of the components on grafting efficiency and concomitant side processes was studied. Grafting of IA (1 wt %) was initiated by 2,5‐dimethyl‐2,5‐di(tert‐butyl peroxy)‐hexane (0.3 wt %) and was carried out in an extruder reactor equipped with a dynamic mixer. An increase in the PP content of the blend led to a lower yield of the grafted product. With low concentrations of LDPE in the blend (up to 25 wt %), grafting efficiency was observed to increase, and this increase was greater in comparison with the additive rule. Between 25 and 99 wt % of LDPE in the blend, grafting efficiency rose monotonically with LDPE concentration. At or below an LDPE content of 25 wt %, the melt flow index (MFI) of [PP/LDPE]‐g‐IA would increase unlike with PP‐g‐IA systems. But a small quantity of PP (below 25 wt %) in the [PP/LDPE]‐g‐IA blends would result in a decreased MFI unlike with LDPE‐g‐IA. The dependence of swell index and melt strength on the ratio of polymeric components in [PP/LDPE]‐g‐IA blends also was investigated. ©2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5095–5104, 2006     

Structure and properties of polyamide 6 blends with low‐density polyethylene grafted by itaconic acid and with neutralized carboxyl groups

A comparative study of the structure and properties of two‐phase blends of polyamide 6 (PA6) and low‐density polyethylene (LDPE) modified in the course of reactive extrusion, by grafting of itaconic acid (IA) without neutralization of carboxyl groups (LDPE‐g‐IA) and with neutralized carboxyl groups (LDPE‐g‐IA^?M⁺) was carried out. It was shown that 30 wt % of LDPE‐g‐IA^?M⁺ introduced to PA6 resulted in blends of higher Charpy impact strength compared with that of PA6/LDPE‐g‐IA blends. The maximum increase was achieved when Mg(OH)₂ was used as a neutralizing agent. The blend morphology has a two‐phase structure with blurred interphases because of increased adhesion between the phases. The neutralization of carboxyl groups in grafted IA did not lead to two‐phase morphology of blends, which had a negative influence on the mechanical properties. It is believed that the differences in the impact strength were caused by the influence of the added neutralizing agents on the structure of interphases, which depends on both the interfaces adhesion and structural effects resulting from the nucleating behavior of the neutralizing agent. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1702–1708, 2004     

Investigation of molecular structure of LDPE modified by itaconic acid grafting

Using thermomechanical spectroscopy, the molecular‐weight distribution and relaxation transitions have been investigated in commercial LDPE and grafted by itaconic acid (LDPE‐g‐IA). This grafting in the molten LDPE was done by reactive extrusion with varied content of reactants in the blend under alternating of a shearing rate applied onto the melt. The dependence of structural relaxation changes in LDPE is shown upon the depth of the mechanochemical transformations and the competing reactions at IA grafting, and also on the chemical crosslinking of the macromolecules. The reason for MWD bimodality for LDPE‐g‐IA obtained in dynamic mixing is the raised homogenization degree of the reactive blend and the higher grafted product yield compared with static mixers. The mixer type substantially affects the structure of the LDPE‐g‐IA amorphous phase. The data obtained reflect chemical transformations of LDPE molecules in IA's presence without an initiator of radical reactions (DCP). Most probable is the IA initiation of molecular crosslinking reactions. There could also occur IA thermodegradation and oligomerization. LDPE and IA or products of acid chemical transformations do not agree thermodynamically (the calculated solubility parameters are 16.1 (MJ/m³)^0.5 for polyethylene and 26.4 (MJ/m³)^0.5 for IA). From the above procedure it can be supposed that nongrafted IA (or its oligomers) exerts an antiplastifying effect on LDPE and LDPE‐g‐IA. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1771–1779, 1999     

Investigation of thermal behavior of poly(2‐hydroxyethyl methacrylate‐co‐itaconic acid) networks

The thermal behavior of poly(2‐hydroxyethyl methacrylate) [PHEMA] homopolymer and poly(2‐hydroxyethyl methacrylate‐co‐itaconic acid) [P(HEMA/IA)] copolymeric networks synthesized using a radiation‐induced polymerization technique was investigated by differential scanning calorimetry, thermogravimetric analysis, and Fourier transform infrared spectroscopy. The glass‐transition temperature (T_g) of the PHEMA homopolymer was found to be 87°C. On the other hand, the T_g of the P(HEMA/IA) networks increased from 88°C to 117°C with an increasing amount of IA in the network system. The thermal degradation reaction mechanism of the P(HEMA/IA) networks was determined to be different from the PHEMA homopolymer, as confirmed by thermogravimetric analysis. It was observed that the initial thermal degradation temperature of these copolymeric networks increased from 271°C to 300°C with IA content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1602–1607, 2007     

Preparation and performance characteristics of short‐glass‐fiber/maleated styrene–ethylene–butylene–styrene/polypropylene hybrid composites

Eighty/twenty polypropylene (PP)/styrene–ethylene–butylene–styrene (SEBS) and 80/20 PP/maleated styrene–ethylene–butylene–styrene (SEBS‐g‐MA) blends reinforced with 30 wt % short glass fibers (SGFs) were prepared by extrusion and subsequent injection molding. The influence of the maleic anhydride (MA) functional group grafted to SEBS on the properties of SGF/SEBS/PP hybrid composites was studied. Tensile and impact tests showed that the SEBS‐g‐MA copolymer improved the yield strength and impact toughness of the hybrid composites. Extensive plastic deformation occurred at the matrix interface layer next to the fibers of the SGF/SEBS‐g‐MA/PP composites during impact testing. This was attributed to the MA functional group, which enhanced the adhesion between SEBS and SGF. Differential scanning calorimetry measurements indicated that SEBS promoted the crystallization of PP spherulites by acting as active nucleation sites. However, the MA functional group grafted to SEBS retarded the crystallization of PP. Finally, polarized optical microscopy observations confirmed the absence of transcrystallinity at the glass‐fiber surfaces of both SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrid composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1303–1311, 2002     

Tensile deformation mechanisms of polypropylene/elastomer blends reinforced with short glass fiber

Polypropylene hybrid composites reinforced with short glass fiber (SGF) and toughened with styrene–ethylene butylenes–styrene (SEBS) elastomer were prepared using extrusion and injection‐molding techniques. Moreover, hybrids compatibilized with SEBS‐grafted maleic anhydride (SEBS‐g‐MA) and hybrid compatibilized with PP grafted with maleic anhydride (PP‐g‐MA) were also fabricated. The matrix of the latter hybrid was designated as mPP and consisted of 95% PP and 5% PP‐g‐MA. Tensile dilatometry was carried out to characterize the fracture mechanisms of hybrid composites. Dilatometric responses showed that the elastic deformation was the dominant deformation mechanism for the SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrids. However, cavitation deformation prevailed over shearing deformation for both hybrids at the higher strain regime. The cavitation strain resulted from the debonding of glass fibers and from the crazing of the matrix in the SGF/SEBS/PP hybrid. In contrast, the cavitation was caused by the debonding of SEBS particles from the matrix of the SGF/SEBS‐g‐MA/PP hybrid. The use of PP‐g‐MA resulting in elastic deformation was the main mode of deformation in the low‐strain region for the SGF/SEBS/mPP and SEBS/SEBS‐g‐MA/mPP hybrids; thereafter, shearing appeared to dominate at the higher strain regime. This was attributed to the MA functional group improving the bonding between the SGF and PP. The correlation between fracture morphology and dilatometric responses also is presented in the article. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 441–451, 2003     

Toughening and compatibilization of polypropylene/polyamide‐6 blends with a maleated–grafted ethylene‐co‐vinyl acetate

In this article, maleated–grafted ethylene‐co‐vinyl acetate (EVA‐g‐MA) was used as the interfacial modifier for polypropylene/polyamide‐6 (PP/PA6) blends, and effects of its concentration on the mechanical properties and the morphology of blends were investigated. It was found that the addition of EVA‐g‐MA improved the compatibility between PP and PA6 and resulted in a finer dispersion of dispersed PA6 phase. In comparison with uncompatibilized PP/PA6 blend, a significant reduction in the size of dispersed PA6 domain was observed. Toluene‐etched micrographs confirmed the formation of interfacial copolymers. Mechanical measurement revealed that the addition of EVA‐g‐MA markedly improved the impact toughness of PP/PA6 blend. Fractograph micrographs revealed that matrix shear yielding began to occur when EVA‐g‐MA concentration was increased upto 18 wt %. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99:3300–3307, 2006     

Effects of rosin‐type nucleating agent and low density polyethylene on the crystallization process of polypropylene

In this article, the influence of rosin‐type nucleating agent (Nu–Na) and low density polyethylene (LDPE) on the crystallization process of polypropylene (PP) from the melt state was studied by differential scanning calorimeter and polarization microscope. It was found that LDPE obstructed the crystallization of PP, decreased the crystallization rate of PP. The rosin‐type nucleating agent Nu–Na substantially improved the rate of crystallization, and decreased the size of spherulites also. The cooperative effect of LDPE and Nu–Na made the crystallization rate of PP increase greatly, the spherulites of PP became much smaller and dispersed more uniformly, and the transparency of PP was further improved evidently. The crystallization temperature (T_c) and melting temperature (T_m) of PP and LDPE in PP/LDPE/Nu–Na (97:3:0.5) were not affected by the number of mixed passes—the nuclei migration from PP to PE had not happened in the mixed passes. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2804–2809, 2003     

The effect of addition of poly(propylene‐g‐acrylic acid) on the morphology of poly(vinyl methylether) and isotactic polypropylene blend

The interfacial adhesion of blend of isotactic polypropylene/poly(vinyl methylether) (i‐PP/PVME) has been improved by the addition of poly(propylene‐g‐acrylic acid) (PP‐g‐AA) as a compatibilizing agent. The phase morphologies of the blends are investigated by optical microscopy (OM) and lateral force microscopy (LFM). The i‐PP/PVME (80/20) blend with no addition of PP‐g‐AA from extrusion process shows a coarse morphology with the dispersed domain size as large as several micrometers; After the addition of 2.5% PP‐g‐AA in the blends, the dispersed PVME domain size decreases greatly. The addition of 5% PP‐g‐AA results in a homogeneous morphology. The blending of PP‐g‐AA with PVME reduces the crystallization temperature of PP‐g‐AA, which is different from that of blending i‐PP with PVME. The increase of the interfacial adhesion is attributed to the specific intermolecular interaction between the acrylic acid group of PP‐g‐AA and the ether group of PVME. The specific interaction is studied by Fourier transform infrared spectroscopy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4098–4103, 2006     

Study of dynamically cured PP/MAH‐g‐PP/talc/epoxy composites

In the present study, an epoxy resin was dynamically cured in a polypropylene (PP)/maleic anhydride–grafted PP (MAH‐g‐PP)/talc matrix to prepare dynamically cured PP/MAH‐g‐PP/talc/epoxy composites. An increase in the torque at equilibrium showed that epoxy resin in the PP/MAH‐g‐PP/talc composites had been cured by 2‐ethylene‐4‐methane‐imidazole. Scanning electron microscopy analysis showed that MAH‐g‐PP and an epoxy resin had effectively increased the interaction adhesion between PP and the talc in the PP/talc composites. Dynamic curing of the epoxy resin further increased the interaction adhesion. The dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had higher crystallization peaks than did the PP/talc composites. Thermogravimetric analysis showed that the addition of MAH‐g‐PP and the epoxy resin into the PP/talc composites caused an obvious improvement in the thermal stability. The dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had the best thermal stability of all the PP/talc composites. The PP/MAH‐g‐PP/talc/epoxy composites had better mechanical properties than did the PP/MAH‐g‐PP/talc composites, and the dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had the best mechanical properties of all the PP/talc composites, which can be attributed to the better interaction adhesion between the PP and the talc. The suitable content of epoxy resin in the composites was about 5 wt %. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Grafting of itaconic acid onto LDPE by the reactive extrusion: Effect of neutralizing agents

Grafting of itaconic acid (IA) onto low‐density polyethylene (LDPE) was performed by reactive extrusion where the initiator was dicumyl peroxide, and the neutralizing agents (NAs) were zinc oxides and hydroxides as well as magnesium oxides and hydroxides. The carboxyl groups were neutralized in molten LDPE directly in the course of acid grafting, and in prefabricated functionalized polyethylene (LDPE‐g‐IA). It was found that neutralizing agents introduced into the initial reaction mixture increase the yield of LDPE‐g‐IA while the carboxyl groups were neutralized partially or totally through chemical reactions. The physical structure of LDPE‐g‐IA did not in fact suffer any substantial changes. From the standpoint of neutralization activity, the NAs studied could be arranged as follows: Zn(OH)₂ > ZnO > Mg(OH)₂ > MgO. NA, added into the initial reaction mixture improved the grafting efficiency of IA onto LDPE. In case of the one‐step process (neutralization simultaneously with grafting), the neutralizing effect appears stronger than that in the two‐step process (neutralization of prepared LDPE‐g‐IA). This means that neutralization of carboxyl groups in IA was less effective when NA was introduced into LDPE‐g‐IA than for the case of the initial reactive mixture. Chemical neutralization of grafted IA results in products of improved resistance to thermal oxidation and thermal stability of melt. This result is of practical importance to the opportunities for widening the application range for PE modified by grafting IA, while preparing polymer blends to be compounded, processed, and used at elevated temperatures. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 828–836, 2003     

Reactive extrusion for the synthesis of nylon 12 and maleated low‐density polyethylene blends via the anionic ring‐opening polymerization of lauryllactam

Nylon 12 was successfully synthesized in a twin‐screw extruder via the anionic ring‐opening polymerization of lauryllactam (LL). Maleated low‐density polyethylene (LDPE–MAH) was added to improve the mechanical properties of nylon 12. The in situ blends of nylon 12 and LDPE–MAH were characterized by mechanical testing and scanning electron microscopy. With increasing LDPE–MAH content, the tensile strength and flexural strength decreased, whereas the blend had improved impact strength and achieved supertoughness when the content of LDPE–MAH was 30 wt %. In the in situ formed low‐density polyethylene‐g‐PA12 copolymer, the domain of the LDPE–MAH phase was finely dispersed in the nylon 12 matrix. The good interface between the two phases demonstrated that LDPE–MAH could be used as a macromolecular activator to induce the polymerization of LL. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Predictors of glass transition in the biodegradable poly‐lactide and poly‐lactide‐co‐glycolide polymers

The biodegradable polylactide (PLA) and polylactide‐co‐glycolides (PLGAs) are being widely investigated for use as scaffolds in bone and ligament reconstruction. The glass transition temperatures (T_g) for these polymers are generally greater than 37°C, causing PLA and PLGA devices to possess brittle characteristics in physiological conditions. To evaluate the possibility of obtaining PLGA polymers with T_g values below 37°C, we evaluated the determinants of T_g in PLA and PLGA copolymers. The T_g, changes in specific heat capacity (ΔC_p), and enthalpic relaxation (ΔH_g) in two consecutive heating cycles were correlated with lactide/glycolide content and intrinsic viscosity [η] for PLA, PLGAs 90:10, 75:25, 65:35, and 50:50. A linear correlation was observed between T_g and intrinsic viscosity, with 0.1 dL/g increase in viscosity resulting in an increase in T_g by about 3.55°C. The selection of PLA and PLGA copolymers with [η] values <0.19 dL/g, corresponding to a viscosity average molecular weight of <70 kDa, will obtain PLA/PLGA polymers with T_g values below 37°C. The lowest attainable T_g values were found to be 28–30°C. Intrinsic viscosity also correlated with ΔC_p differences between aged and rapidly cooled polymers, and is therefore important in predicting free volume changes within these polymers upon aging. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1983–1987, 2006     

Polypropylene/polypropylene‐grafted acrylic acid copolymer/ethylene–Acrylic acid copolymer ternary blends for hydrophilic polypropylene

Ternary blends of polypropylene (PP), a polypropylene‐grafted acrylic acid copolymer (PP‐g‐AA), and an ethylene–acrylic acid copolymer (EAA) were prepared by melt blending. The surfaces of films with different contents of these three components were characterized with contact‐angle measurements. Scanning electron microscopy, Fourier transform infrared spectroscopy, differential scanning calorimetry, and thermogravimetric analysis were used to characterize the microstructure, melting and crystalline behavior, and thermal stability of the blends. The contact angles of the PP/PP‐g‐AA blends decreased monotonically with increasing PP‐g‐AA content. With the incorporation of EAA, the contact angles of the PP/PP‐g‐AA/EAA ternary blends decreased with increasing EAA content. When the concentration of EAA was higher than 15 wt %, the contact angles of the ternary blends began to increase. Scanning electron microscopy observations confirmed that PP‐g‐AA acted as a compatibilizer and improved the compatibility between PP and EAA in the ternary blends. Differential scanning calorimetry analysis suggested that acrylic acid moieties could act as nucleating agents for PP in the polymer blends. Thermogravimetric analysis and differential thermogravimetry confirmed the optimal blend ratio for the PP/PP‐g‐AA/EAA ternary blends was 70/15/15. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 436–442, 2006     

Morphological,thermal, rheological,and mechanical properties of PP/EVOH blends compatibilized with PP‐g‐IA

We prepared some blends of polypropylene (PP) and ethylene vinyl alcohol (EVOH) with and without a compatibilizer. As a new compatibilizer, we synthesized polypropylene grafted with itaconic acid (PP‐g‐IA) using Brabender mixing system. We investigated the morphological, thermal, rheological, and mechanical properties of a compatibilized blends (PP/EVOH/PP‐g‐IA) and not compatibilized blends (PP/EVOH). Our experiments showed that carboxylic acid groups in PP‐g‐IA and hydroxyl group in EVOH formed strong in situ hydrogen bond in the compatibilized blends, resulting in better morphological and mechanical properties of the compatibilized blends than those of not compatibilized blends. POLYM. ENG. SCI., 56:1240–1247, 2016. © 2016 Society of Plastics Engineers     

Influence of Copolymer Composition and Curing on Toughness of Isotactic Polypropene Blended Together with Metallocene‐EPDM and Ethene/Propene/Vinylcyclohexane Terpolymers

Ethene/propene terpolymers containing either 1‐vinylcylohexene‐4 (VCHen) or vinylcyclohexane (VCHan) as termonomer component were prepared using MAO‐activated rac‐Me₂Si(2‐MeBenz[e]Ind)₂ZrCl₂ (MBI). Propene content was varied between 26 and 72 wt.‐% with less than 1 mol‐% termonomer incorporation. Blends containing 85 vol.‐% isotactic polypropene (i‐PP) and 15 vol.‐% of the two EP terpolymer families were prepared by melt‐compounding in a twin‐screw kneader at 200°C to examine the role of sulfur‐mediated crosslinking of the unsaturated EPDM terpolymer phase in comparison to the corresponding blends containing non‐crosslinked saturated EP/VCHan terpolymers. The observed glass temperature (T_g) depression of the T_g of EP(D)M phases with respect to the T_g of the corresponding bulk EP(D)M was attributed to the presence of thermally induced stresses in both blend systems. Blends of i‐PP with crosslinked EPDM showed smaller T_g depression with respect to those of iPP/EPM blends containing non‐crosslinked EP and EPM dispersed phases. Morphology differences were detected for i‐PP/EPM and dynamically vulcanized i‐PP/EPDM blends by means of atomic force microscopy (AFM). The crosslinked i‐PP/EPDM blends exhibited significantly improved low temperature toughness as compared to the corresponding non‐crosslinked i‐PP/EPM blends. Curing of the EPDM elastomer phase in i‐PP/EPDM (85 vol.‐%/15 vol.‐%) blends afforded significantly improved toughness/stiffness balance and a wider toughness window with respect to the corresponding i‐PP/EPM and i‐PP/EP blends without sulfur‐cured rubber phases.     

Dynamic study of free volume properties in polyethylene/styrene butadiene rubber blends by positron annihilation lifetime method

Positronium (Ps) formation in low and high‐density polyethylene (LDPE and HDPE) and styrene butadiene rubber (SBR), as well as in their blends (LDPE/SBR: 50/50 and HDPE/SBR: 50/50) has been investigated by positron annihilation lifetime (PAL) measurements as a function of low temperature (100–300 K). The glass transition temperature (T_g) for the initial polymers and their blends are determined by ortho‐positronium (o‐Ps) lifetime, τ₃ versus temperature as well as by differential scanning calorimetry (DSC) measurements. The temperature dependence of nanoscale free volume size shows similar trend for all the investigated samples indicating an abrupt change at T_g, which is found to be higher for SBR sample characterized by its high chain mobility. In addition, The T_g values deduced from PAL measurements are compared with the corresponding data deduced from DSC. The variation of o‐Ps formation probability I₃ versus temperature for polyethylene and their blends were interpreted in the frame work of spur reaction model of Ps formation. On the other hand, the lifetime coefficient below and above T_g is found to be one order of magnitude larger than the linear expansion coefficient. This constitutes evidence that Ps is only probing free volumes. The results obtained from change in free volume–hole distribution with temperature reflect both thermal expansion and increase in free volume–hole size with the rise in temperature. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Poly(ethylene terephthalate)/polypropylene reactive blends through isocyanate functional group

To evaluate the compatibilization effects of an isocyanate group on poly(ethylene terephthalate)/polypropylene (PET/PP) blends through a reactive blend, PP grafted with 2‐hydroxyethyl methacrylate‐isophorone diisocyanate (PP‐g‐HI) was prepared and blended with PET. In view of the blend morphology, the presence of PP‐g‐HI reduced the particle size of the dispersed phase by the reduced interfacial tension between the PP and PET phases, indicating the in situ copolymer (PP‐g‐PET) generated during the melt blending. The DSC thermograms for the cooling run indicated that the PET crystallization in the PP‐g‐HI rich phase was affected by the chemical reactions of PET and PP‐g‐HI. The improved mechanical properties for the PET/PP‐g‐HI blends were shown in the measurement of the tensile and flexural properties. In addition, the water absorption test indicated that the PET/PP‐g‐HI blend was more effective than the PET/PP blend in improving the water resistance of PET. The positive properties of PET/PP‐g‐HI blends stemmed from the improved compatibilization of the PET/PP blend. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1056–1062, 2001     

Synthesis and characterization of fluorine and nitrile containing polyimides

A series of polyimides were synthesized from new diamine, Bis [4,4′‐amino‐5,5′ trifluoromethyl phenoxy‐(hexafluoro isopropylidine) phenoxy phenyl] benzonitrile [BATFB] and various aromatic tetracarboxylic anhydrides by thermal and chemical imidization routes. The BATFB was synthesized in two steps by nucleophilic displacement reaction of 2,6‐dichloro benzonitrile, 4,4′‐(hexafluoro isopropylidine) diphenol and 2‐amino‐5‐fluoro benzotrifluoride in the presence of anhydrous potassium carbonate in N,N′‐dimethyl acetamide (DMAc) and the structure was confirmed by FTIR spectroscopy and CHNSO analyzer. The polymers were characterized by FTIR spectroscopy and thermal analysis were performed by differential scanning calorimetry and thermogravimetric analysis methods. The prepared polyimides had glass transition temperatures between 230 and 290°C and their 10% weight loss were recorded in the range 550–590°C in N₂ atmosphere. Majority of polymers are found to be soluble in most of the organic solvents such as DMSO, DMF, DMAc, m‐cresol, and THF even at room temperature and few becomes soluble on heating. The prepared polyimides showed water uptake values 0.34–0.54 wt % at room temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3455–3461, 2006     

Synthesis,characterization, and optoelectronic properties of two new polyfluorenes/poly(p‐phenylenevinylene)s copolymers

Two novel copolymers of polyfluorenes/poly(p‐phenylenevinylene)s copolymers with p‐tert‐butyl‐phenylenemethylene groups in the C‐9 position of alternating fluorene unit, poly[1,4‐(2,5‐dibutyloxyl)‐phenyleneviny lene‐alt‐9‐(p‐tert‐butyl‐phenylenemethylene)fluorene] and poly[1,4‐(2,5‐dioctyloxyl)‐phenylenevinylene‐alt‐9‐(p‐tert‐butyl‐phenylenemethylene)fluorine], have been synthesized via the Heck polycondensation reaction. The synthesized polymers were characterized by FTIR, NMR, DSC, TGA, UV–vis, and PL spectra. The polymers showed high glass transition temperatures and good thermal stability. A polymer light‐emitting diode with the configuration ITO/PEDOT:PSS/P2/Ca/Al has been fabricated. The device emitted a yellow light with a peak wavelength of 578 nm similar to the PL spectra of the copolymer film. A maximal luminance of 534 cd/m² was obtained at a driving voltage of 24.5 V. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3955–3962, 2006