Adhesion of surface‐grafted low‐density polyethylene plates with enzymatically modified chitosan solutions

An investigation was undertaken on application of dilute chitosan solutions modified by tyrosinase‐catalyzed reaction with 3,4‐dihydroxyphenetylamine (dopamine) to adhesion of the low‐density polyethylene (LDPE) plates surface‐grafted with hydrophilic monomers. Tensile shear adhesive strength effectively increased with an increase in the grafted amount for methacrylic acid‐grafted and acrylic acid‐grafted LDPE (LDPE‐g‐PMAA and LDPE‐g‐PAA) plates. In particular, substrate breaking was observed at higher grafted amounts for LDPE‐g‐PAA plates. The increase in the amino group concentration of the chitosan solutions and molecular mass of the chitosan samples led to the increase in adhesive strength. Adhesive strength of the PE‐g‐PMAA plates prepared at lower monomer concentrations sharply increased at lower grafted amounts, which indicates that the formation of shorter grafted PMAA chains is an effective procedure to increase adhesive strength at lower grafted amounts. Infrared measurements showed that the reaction of quinone derivatives enzymatically generated from dopamine with carboxyl groups was an important factor to increase adhesive strength in addition to the formation of the grafted layers with a high water absorptivity. The above‐mentioned results suggested that enzymatically modified dilute chitosan solutions can be applied to an adhesive to bond polymer substrates. The emphasis is on the fact that water is used as a solvent for preparation of chitosan solutions and photografting without any organic solvents. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Adhesion of polyethylene plates photografted with methacrylic acid and acrylic acid with enzymatically modified chitosan solutions and X‐ray photoelectron spectroscopy analysis of failed surfaces

An investigation was carried out on the application of dilute chitosan solutions modified by a tyrosinase‐catalyzed reaction with 3,4‐dihydroxyphenetylamine (dopamine) to the adhesion of low‐density polyethylene (LDPE) and high‐density polyethylene (HDPE) plates photografted with carboxyl‐group‐containing hydrophilic monomers, such as methacrylic acid (MAA) and acrylic acid (AA). In the case where photografting was carried out at lower monomer concentrations or at lower temperatures, the adhesive strength sharply increased with lower grafted amounts. A sharp increase in the adhesive strength was found to be due to the formation of shorter grafted polymer chains at lower monomer concentrations and/or the restriction of the location of grafting to the outer surface region at lower temperatures. In addition, the adhesive strength also sharply increased at even lower grafted amounts for photografting onto the HDPE plates and/or that of AA because the location of grafting was restricted to the outer surface region. For the AA‐grafted LDPE and HDPE plates, substrate breaking was observed. This was attributed to the coverage of the substrate surfaces with grafted poly(acrylic acid) chains at lower grafted amounts and a high water absorptivity of the grafted layer. X‐ray photoelectron spectroscopy (XPS) analysis of the grafted LDPE plates incubated in a dopamine solution containing tyrosinase suggested that the increase in the adhesive strength was caused by the penetration of enzymatically modified chitosan solutions in the grafted layers and the subsequent reaction of quinone derivatives enzymatically generated with grafted polymer chains. In addition, the surface analysis of the failed surfaces by XPS showed that as the adhesive strength increased, the location of failure was shifted from the interface between the layers mixed with enzymatically modified chitosan materials and grafted polymer chains to the inside the grafted layer containing enzymatically modified chitosan materials. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Estimation of surface properties of grafted layers formed on low- and high-density polyethylene plates by photografting of methacrylic acid and acrylic acid at different monomer concentrations and temperatures

An investigation was carried out on estimation of hydrophilicity, wettability and water-absorptivity, and surface analysis by X-ray photoelectron spectroscopy of the low- and high-density polyethylene (LDPE and HDPE) plates photografted with methacrylic acid (MAA) and acrylic acid (AA) at different monomer concentrations or temperatures. Wettability of the MAA-grafted LDPE and HDPE plates increased with grafted amounts, and became constant when the substrate surfaces were fully covered with the grafted polymer chains. On the other hand, for the AA-grafted LDPE and HDPE plates, wettability had the maximum value, and then gradually decreased against the grafted amount probably due to aggregation of grafted PAA chains, although the surfaces were covered with grafted PAA chains at lower grafted amounts compared with grafted PMAA chains. Water-absorptivity sharply increased at lower grafted amounts due to formation of shorter grafted polymer chains for photografting at lower monomer concentrations or due to restriction of the location of grafting to the outer surface region for photografting at lower temperatures. Therefore, for photograftings of AA or onto the HDPE plates, the substrate surfaces were covered with grafted polymer chains and the grafted layers formed possessed higher water-absorptivity at lower grafted amounts. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Improvement of autohesive and adhesive properties of polyethylene plates by photografting with glycidyl methacrylate

Glycidyl methacrylate (GMA) was photografted with the low‐ and high‐density polyethylene (LDPE and HDPE) plates to provide their surfaces with autohesive and adhesive properties. The chemical composition and wettability of the GMA‐grafted LDPE and HDPE (LDPE‐g‐PGMA and HDPE‐g‐PGMA) plates remained constant above full coverage of the surfaces with grafted PGMA chains. Autohesive strength obtained with 1,4‐dioxane as a good solvent of PGMA increased with an increase in the grafted amount and substrate breaking was observed at the grafted amount of 117 μmol/cm². The grafted amount at substrate breaking was decreased by increasing the temperature and load during heat pressing. Adhesive strength was effectively enhanced by use of multi‐functional amine compounds because of the increase in the reaction between primary or secondary amine groups and epoxy groups appended to the grafted PGMA chains. In addition, the decrease in the amine compound concentration and the increase in the number of amino groups in the amine compounds used led to the decrease in the grafted amounts at substrate breaking. Substrate breaking occurred at lower grafted amounts for the HDPE‐g‐PGMA plates than for the LDPE‐g‐PGMA plates because the location of the photografting was restricted to the outer surface region for the HDPE plate. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 493–500, 2007     

Adhesion of grafted polypropylene plates with enzymatically modified chitosan solutions and analysis of failed surfaces by X‐ray photoelectron spectroscopy

In this study, hydrophilic monomers were photografted onto the PP plates at different monomer concentrations and temperatures, and grafted PP plates were bonded with enzymatically modified chitosan solutions. Their adhesive strength properties were discussed in relation to the grafting conditions and hydrophilic properties such as wettability and water‐absorptivity. In addition, the location of failure was investigated by X‐ray photoelectron spectroscopy analysis of failed surfaces. Wettability of the grafted PP plates except for the PP grafted with acrylic acid (PP‐g‐PAA) plates remained constant above the grafted amounts at which the PP surfaces were fully covered with grafted polymer chains. On the other hand, wettability of the PP‐g‐PAA plates passed through the maximum value and then gradually decreased with the grafted amount probably because of the aggregation of grafted PAA chains. Water‐absorptivity of the grafted layers formed at lower monomer concentrations or temperatures sharply increased at lower grafted amounts. The adhesive strength increased with an increase in the grafted amount and substrate breaking was observed for PP‐g‐PAA plates because enzymatically modified chitosan solutions were successfully penetrated in the grafted layers and quinone derivatives reacted with carboxy groups of grafted PAA chains. Failure occurred in the layers composed of grafted PAA chains and components containing in enzymatically modified chitosan solutions and the location was shifted to the inside of grafted layer, as the grafted amount increased. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1369‐1376, 2013     

Adhesion of ultrahigh molecular weight polyethylene plates photografted with hydrophilic monomers and evaluation of failure location by X‐ray photoelectron spectroscopy

In this study, methacrylic acid (MAA) and acrylic acid (AA) were photografted onto the ultrahigh molecular weight polyethylene (UHMWPE) plates at different monomer concentrations and temperatures, and the grafted UHMWPE plates were bonded with aqueous polyvinyl alcohol (PVA) solutions. The tensile shear adhesive strength of both grafted UHMWPE plates was also discussed in relation to wettability and water absorptivity. The location of failure was also estimated by X‐ray photoelectron spectroscopy (XPS). Wettability of the MAA‐grafted UHMWPE plates became constant, when the UHMWPE surface was fully covered with grafted PMAA chains. Conversely, wettability of the AA‐grafted UHMWPE plates passed through the maximum value and then gradually decreased against the grafted amount probably due to aggregation of grafted PAA chains. Water absorptivity of the grafted layers formed at lower monomer concentrations or temperatures sharply increased at lower grafted amounts. The adhesive strength increased with the grafted amount and substrate breaking was observed at higher grafted amounts, indicating that a main factor to increase the adhesive strength is the formation of a grafted layer by shorter grafted polymer chains and/or the restriction of the location of photografting to the outer surface region. In addition, surface analysis by XPS showed that failure occurred in the boundary between the layer composed of grafted polymer chains and PVA chains and the ungrafted layer at a low adhesive strength, and the location of failure was shifted to the grafted layer containing PVA chains at the grafted amount increased. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40133.     

Autohesive properties of polyolefins photografted with hydrophilic monomers

In an attempt to provide polyolefins such as low‐ and high‐density polyethylene and polypropylene with autohesive properties, hydrophilic monomers such as methacrylic acid (MAA), acrylic acid (AA), and 2‐(dimethylamino)ethyl methacrylate (DMAEMA) were photografted onto their surfaces. The wettabilities of the grafted plates stayed constant above full coverage of the substrate surfaces with grafted polymer chains, except for the AA‐grafted plates. The amount of absorbed water for the grafted layers formed increased with an increase in the number of grafted polymer chains. The autohesive strength increased with an increase in the wettability and water absorptivity of the grafted plates as well as the temperature and load on heat pressing. For all grafted plates substrate breaking at autohesive strength measurements was observed for grafted amounts 2–3 times as much as those at adhesive strength measurements. The substrate breakings for the HDPE and PP plates photografted with AA and DMAEMA at adhesive strength measurements were observed at lower grafted amounts compared with those photografted with MAA. This study has made it clear that the photografting of hydrophilic monomers onto polyolefin materials can markedly enhance autohesivity without any adhesives as well as the adhesivity for high grafted amounts. Therefore, polyolefin materials with improved autohesivity and adhesivity can be widely applied in adhesive fields, including for novel uses. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2244–2252, 2003     

Adsorption and desorption properties of cationic polyethylene film gels to organic anions and their regeneration

An investigation was undertaken on the adsorption and desorption properties of 2‐(dimethylamino)ethyl methacrylate grafted polyethylene (PE‐g‐PDMAEMA) films to anionic dye anions with one to three sulfonic groups in response to pH and temperature changes. The amounts of dye anions adsorbed on the PE‐g‐PDMAEMA films passed through the maximum values at about pH 3 because of an increase in the protonation of dimethylamino groups caused by a decrease in the pH value. The amounts of adsorbed dye anions decreased below pH 3 because the ionic strength increased with the addition of HCl to adjust the initial pH values of the aqueous dye solutions. The amounts of adsorbed dye anions decreased with an increase in the number of sulfonic groups in the dye molecules at the same pH value because electrostatic repulsion was generated between free sulfonic groups of the dye anions adsorbed onto the PE‐g‐PDMAEMA films and free dye anions in the medium. A large number of dye anions adsorbed were desorbed from the PE‐g‐PDMAEMA film with initial pH values above 11.0. The cyclic processes of adsorption at pH 3.0 and desorption at pH 11.0 were repeated without considerable fatigue. The PE‐g‐PDMAEMA films showed practically regenerative adsorption and desorption behavior in response to the pH changes. In addition, when the dye‐anion‐adsorbed PE‐g‐PDMAEMA films were alternately immersed in water at two different temperatures, dye anions were desorbed in water at higher temperatures without any chemical agents because of the deprotonation of dimethylamino groups and thermosensitive contraction of grafted PDMAEMA chains. These results indicate that PE‐g‐PDMAEMA films can be applied as regenerative ion‐exchange membranes for adsorption and desorption processes of anionic compounds in response to the pH and temperature. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 381–391, 2006     

Crystalline morphology at the interface between polyethylene‐grafted glass and polyethylene

Adhesion measurements performed on a polyethylene (PE)‐grafted‐glass interface showed that the structure of the PE free chains (matrix) was an important parameter. The fracture energy was higher for interfaces prepared from a linear matrix, such as high‐density polyethylene (HDPE), than for those from a branched PE [low‐density polyethylene (LDPE)]. Therefore, the microstructure of the grafted PE/PE matrix interface or interphase was investigated as a function of the molar masses of the connectors and the structure (linear or branched) of the free PE matrix chains. As the grafted chains were linear, a cocrystalline structure with free chains of the HDPE matrix was generated. PE connecting chains led to a low capacity for cocrystallization with LDPE. Cocrystallization was studied with blends based on functionalized PE chains and PE matrices. These blends were assumed to be miscible, as substantiated by a single differential scanning calorimetry (DSC) peak. The DSC analyses were confirmed by wide‐angle X‐ray scattering, which revealed a crystalline orientation of the chains in the interphase, that is, in the vicinity of the glass surface. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 214–229, 2003     

Adsorption and desorption properties of expanded poly(tetrafluoroethylene) films grafted with DMAEMA and their regeneration

An investigation was undertaken on the adsorption and desorption properties of the expanded poly (tetrafluoroethylene) (ePTFE) films grafted with 2‐(dimethylamino)ethyl methacrylate (DMAEMA) to anionic dye anions with one to three sulfonic groups in response to temperature changes. The amount of adsorbed metanil yellow (MY) anions increased with the grafted amount and most of the dimethylamino groups appended to the grafted PDMAEMA chains worked as an adsorption site to MY anions for the DMAEMA‐grafted ePTFE (ePTFE‐g‐PDMAEMA) films with the grafted amounts of higher than 1.1 mmol/g. When the dye‐anion‐adsorbed ePTFE‐g‐PDMAEMA films were alternately immersed in water at two different temperatures, dye anions were desorbed from the ePTFE‐g‐PDMAEMA films at higher temperatures without any chemical agents. The amount of desorbed dye anions increased with an increase in the temperature of water from 40 to 80°C. Desorption of dye anions is caused by either deprotonation of dimethylamino groups appended to the grafted PDMAEMA chains or thermosensitive contraction of the grafted PDMAEMA chains. These results indicate that the ePTFE‐g‐PDMAEMA films can be applied as a regenerative ion‐exchange membrane for adsorption and desorption processes of anionic compounds in response to the temperature change. The thermally regenerative ion‐exchange properties of the ePTFE‐g‐PDMAEMA films was superior to that of the PE‐g‐PDMAEMA films reported in our previous article in the fact that the total degree of desorption was higher for the ePTFE‐g‐PDMAEMA films. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Retention and reusability of trypsin activity by covalent immobilization onto grafted polyethylene plates

This study investigated the activity of trypsin that had been covalently immobilized onto acrylic acid (AA)– and methacrylic acid (MAA)–grafted polyethylene (PE) plates—PE–g–PAA and PE–g–PMAA—using a water‐soluble carbodiimide as a coupling agent, as a function of the immobilized amount, the grafted amount, the pH value on immobilization, and the pH value and temperature at the activity measurement. The activity of trypsin immobilized on the PE–g–PAA plates at pH 6.0 decreased with an increase in the immobilized amount because of the crowding of trypsin molecules in the vicinity of the surfaces of the grafted PAA layers. The increase in the grafted amount resulted in a decrease in the activity of immobilized trypsin because of a decrease in the diffusivity of BANA molecules caused by the formation of dense grafted PAA layers for the PE–g–PAA plates and led to the increased activity because of the increase in the hydrophilicity of the whole grafted layers for the PE–g–PMAA plates. The activity of trypsin immobilized on the PE–g–PAA and PE–g–PMAA plates at pH 6 increased with an increase in the pH value, probably because of the expansion of trypsin‐carrying grafted PAA and PMAA chains and the increased diffusivity of Nα‐benzoyl‐DL ‐arginine‐nitroanilide hydrochloride molecules in the grafted layers. The optimum temperature of the activity of immobilized trypsin shifted to 50°C from 30°C for native trypsin. Immobilized trypsin was reusable without any denaturation and isolation at temperatures ranging from 20°C to 60°C and pH values ranging from 6 to 10. Trypsin immobilized on a PE–g–PAA plate had 95% of the remaining activity in relation to native trypsin at 30°C after preservation in a pH 7.8 buffer at 4°C over 6 months. These results made clear that alkaline and thermal stability, reusability, and storage stability can be much improved by the covalent coupling of trypsin on PE–g–PAA and PE–g–PMAA plates. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3574–3581, 2003     

Synthesis and evaluation of compatibilizer based on interpenetrating polymer networks (IPN) for PET/LDPE blends

The present work considers the evaluation of recycled polymers, which are generally incompatible and are degraded during recycling with fatal consequences to their thermal and mechanical properties. Regarding this subject, the synthesis of a new compatibilizer in network form was carried out in order to counter such incompatibility. In this sense, low density polyethylene (LDPE) and poly(ethylene terephthalate) (PET) were compatibilized via the implementation of an interpenetrating polymer network (IPN), which was specifically synthesized to possess chemical groups that are akin to both plastics, PET and LDPE. The effects of the relative amount of poly(acrylic acid) (PAA) in the compatibilizer and the amount in the blends of PET/LDPE were evaluated. The results show that mechanical properties and interfacial adhesion of PET/LDPE blends were modified and improved with the addition of the synthesized compatibilizer compared with a commercial compatibilizer (polyethylene grafted with maleic anhydride, PE‐g‐AA). © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43704.     

Analysis of polyolefin blends by crystallization analysis fractionation

Crystallization analysis fractionation (CRYSTAF) is a new technique for the analysis of the composition of polyolefin blends. CRYSTAF fractionates blend components of different crystallizability by slow cooling of a polymer solution. During the crystallization step the concentration of the polymer solution is monitored as a function of temperature. Different from DSC, blends of HDPE, LDPE and PP are separated into the components and quantitative information can be obtained directly from the crystallization curves. Even very low amounts of one component in PE/PP and HDPE/LDPE blends can be quantified with good accuracy. The applicability of the technique for the analysis of Ziegler‐Natta, and metallocene‐catalyzed polyolefins is demonstrated and the analysis of waste plastics fractions is discussed.     

Amine modified polyethylenes,prepared in near critical propane,as adhesion promoting agents in multilayered HDPE/PET films

High density polyethylene [HDPE] grafted with 0.13, 0.04 and 1.04 wt% maleic anhydride (abbr.: PEMA) was modified with an excess of a variety of diamines in near critical propane. The resulting amic acid groups were quatitatively imidized to the corresponding imide (PEMI) in the melt. Increasing the percentage maleic anhydride grafted on the HDPE resulted, upon reaction with the diamines, in an increased gel content, due to crosslinking. Three‐layered films were prepared using HDPE film and polyethylene dterephathalate (PET) film as the outer layers and the PEMAs and PEMIs as the inner layer. Adhesion strengths were measured using a T‐peel test. Increasing the bonding temperature resulted in an improved adhesion. The most optimal system for adhesion proved to be HDPE grafted with 0.40 wt% MA and modified with a pendent secondary amine group. For this system the lowest number of reactive amine groups was lost owing to crosslinking reactions, so the highest concentration of amines is available for interactions with the PET film. The absence of extensive HDPE crosslinking in addition implies a better flow of the adhesive layer during lamination. From contact angle measurements, it was observed for all samples that after delamination of the three‐layered system, PET was present on the PE‐surface and PE was present on the PET‐surface.     

聚乙烯反应挤出接枝马来酸酐的研究

以过氧化二异丙苯(DCP)为引发剂,使用反应挤出机研究了不同种类聚乙烯及其共混物接枝马来酸酐的反应规律。实验结果表明:产物的接枝率和熔体流动速率(MFR)变化与聚乙烯的种类有直接关系,接枝性能从优到差的顺序为:LDPE>LLDPE>HDPE;引发剂DCP对LDPE接枝产物的MFR影响显著,对LLDPE次之,对HDPE的MFR几乎没有影响;聚乙烯共混物的接枝性能取决于组成共混物的聚乙烯种类和用量。接枝产物及纯化后样品的红外光谱分析表明,酐基是以化学键连接到聚乙烯分子链上,接枝产物几乎不含游离态的马来酸酐。     

Influence of Processing Additives on Adhesive Properties of Surface‐Modified Low‐Density Polyethylene

Summary: The paper deals with the surface and adhesive properties of low‐density polyethylene modified by corona discharge, which appear during the long‐term hydrophobic recovery of the modified polymer. The study was aimed at the change in polarity during aging of low‐density polyethylene modified by corona discharge reducing the surface free energy, its polar component and the mechanical work of adhesion. During the long‐term hydrophobization of low‐density polyethylene the main decrease of the surface properties appeared within the first 30 d after modification. In the course of further aging the hydrophobic recovery of the polymer proceeded more slowly. It has been found that the value of the surface and adhesive properties of low‐density polyethylene after modification with corona discharge as well as the dynamics of their decrease during the aging is to a great extent dependent on the presence of the processing additives in the polymer.

Mechanical work of adhesion of LDPE modified by corona discharge to poly(vinyl acetate) during hydrophobic recovery: a) additive‐free LDPE, b) LDPE with additives.     

Phase structural analyses of polyethylene coatings on high‐density papers. III. Determination of the crystallite thicknesses by T1 measurements

Two different extrusion‐coating qualities of polyethylene, namely LDPE and HDPE, were coated on high‐density papers. Differences were observed with respect to their response to storage and low temperature heat treatment. HDPE does not respond to storage at ambient temperature and heat treatment in the same way as LDPE. The LDPE‐coating exhibits an increase in the monoclinic crystalline fraction at the paper surface as a result of heat treatment. The nature of this response appears to be a result of adhesion to a paper surface, the properties of this surface, orientation of polymer chains, and chain mobility differences. The increase of the monoclinic fraction is shown to relate to an increase of the mean crystallite thickness and initiation of new crystallites at the paper surface. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 235–241, 2004     

Morphology and properties of nylon 6 and high density polyethylene blends in presence of nanoclay and PE‐g‐MA

In this study, we report the synergistic effect of nanoclay and maleic anhydride grafted polyethylene (PE‐g‐MA) on the morphology and properties of (80/20 w/w) nylon 6/high density polyethylene (HDPE) blend. Polymer blend nanocomposites containing nanoclay with and without compatibilizer (PE‐g‐MA) were prepared by melt mixing, and their morphologies and structures were examined with scanning electron microscopy (SEM) and wide angle X‐ray diffractometer (WAXD) study. The size of phase‐separated domains decreased considerably with increasing content of nanoclay and PE‐g‐MA. WAXD study and transmission electron microscopy (TEM) revealed the presence of exfoliated clay platelets in nylon 6 matrix, as well as, at the interface of the (80/20 w/w) nylon 6/HDPE blend–clay nanocomposites. Addition of PE‐g‐MA in the blend–clay nanocomposites enhanced the exfoliation of clays in nylon 6 matrix and especially at the interface. Thus, exfoliated clay platelets in nylon 6 matrix effectively restricted the coalescence of dispersed HDPE domains while PE‐g‐MA improved the adhesion between the phases at the interface. The use of compatibilizer and nanoclay in polymer blends may lead to a high performance material which combines the advantages of compatibilized polymer blends and the merits of polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Hydrophilic and adhesive properties of methacrylic acid-grafted polyethylene plates

Methacrylic acid (MAA) was grafted onto polyethylene (PE) surfaces by simultaneous irradiation with UV rays in the liquid phase to estimate hydrophilic and mechanical properties for MAA-grafted PE plates. The amount of grafted MAA increased sigmoidally with UV irradiation time, and the higher grafted amount was obtained at higher monomer concentrations. With an increase in grafting of MAA, the wettabilities from the contact angles of water were enhanced and the refractive indices from the ellipsometry decreased. Though the contact angles remained constant above the grafted amount of 0.02 mmol/cm², the refractive indices approached the value of PMAA around 0.009 mmol/cm², indicating that the PE surfaces were fully covered with grafted PMAA chains. Then, at a fixed grafted amount, the grafted layer can absorb more water and the grafted PE plates possessed higher tensile shear adhesive strength, in case grafting was carried out at lower monomer concentrations. Surface properties depended on the density of carboxyl group at the surfaces of grafted layers, whereas adhesive properties depended on the structural properties of grafted chains as well as on the density of carboxyl group of the whole grafted layers.     

Thermal and mechanical properties of silane‐grafted water crosslinked polyethylene

The effects of linear low density polyethylene (LLDPE) grafting with vinyltrimethoxysilane by different types and contents of peroxide were studied. When grafting silane onto LLDPE, with 0.10 phr of Dicumyl peroxide (DCP) or 0.05 phr content of 2,5‐Dimethyl‐2,5‐di (tert‐butyl‐peroxy)‐hexane (DHBP), it was found that the grafting effect was improved; however, as Di(2‐tert‐butylperoxypropyl ‐(2))‐benzene (DIPP) or excess DHBP was used, LLDPE was supposed to cause self‐crosslinking, which reduced the grafting effect of silane and was invalid in the processing of extrusion. In this study, vinyl trimethoxysilane (VTMS) was grafted onto various polyethylenes (HDPE, LLDPE, and LDPE) using DCP as an initiator in a twin screw extruder. The grafted polyethylenes were able to crosslink utilizing water as the crosslinking agent. The effects of varied crosslinking time on the mechanical properties of the crosslinked polyethylenes were studied. It was found that the HDPE and LLDPE were apt to crosslink during the grafting process and thus decreased the grafting ratio. Multiple melting behavior was observed for crosslinked LDPE and LLDPE. Mechanical and thermal properties of the crosslinked PE are much better than that of uncrosslinked PE. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2383–2391, 2005