共查询到19条相似文献,搜索用时 218 毫秒
1.
2.
3.
4.
5.
在使用聚酯成形网之前抄造胶印新闻纸,基本上用的都是65目的铜质成形网。聚酯成形网一般选用4综系列单层网,网号为27254者居多,其T值为50~57,开孔率为16%~17%。这两种成形网,对上网纤维在成纸里的留着量、网下白水质量的影响,是值得进一步研究和探讨的。我们选用Baner-McNett纤维筛分仪或类似功能的筛分仪,对不同成形网的上网浆和卷取处的成纸以及网下白水进行筛分,然后分别对它们的筛分结果数据进行分析对比。所得的筛分结果数据分述于下列各表。分析与结论由表1、表2数据分析,使用65目铜网和27254聚酯成形网抄造胶印新闻… 相似文献
6.
本文讨论北美所有夹网成形器的配置,以及如何为每种类型的成形器及其使用位置、生产纸种来选择成形网。塑料成形网在夹网纸机上的运行效能取决于很多可变因素,包括纸机型式、浆料、纸种、定量以及抄速等。本文将详细讨论在全部北美生产中的夹网成形器上使用塑料成形网时 相似文献
7.
本文在工业用呢织物纹板图的分解和组合的基础上,进一步分析了多层接结及多层接结摺织或管状的结构。这类织物用于高线压毛毯、聚酯成形网、造纸帆布、工业用带及其他工业用呢等。 相似文献
8.
随着纸机车速的不断提高,对清洗的要求越来越严格,而且,抄纸过程中要加入更多的研磨性填料,因此,需要不断提高成形网的耐磨性和使用寿命.如何判断、描述成形网的磨损率尤为重要.同时,在不同纸机成形网磨损率最小化的研究中,计算成形网的磨损系数是非常必要的. 相似文献
9.
夹网成形的高速造纸技术的结合,必须着重考虑成形网的特性。这里所使用的成形网之特性,不同于过去的长网纸机和混合成形技术对成形网的要求。因为纸页的两面性、高浓抄造、清洁运转甚至纸页的剖面结构都与成形网的特性有关。这些问题在成形网的发展过程中,都大大地作了改进,满足了各种成形器对成形网的要求。(图1) 相似文献
10.
该文论述了关于造纸压榨织物毯体设计,制造和运行技术的现状和未来的发展。主要述及在其运行过程里提高毯体结构以抵抗被化学介质腐蚀使机械部件磨蚀及杂质污物过早填塞和压榨装置压紧压实等性能而延长织物运行寿命。这也是造纸压榨织物在设计、制造和运行技术未来发展的方向。 相似文献
11.
Hydroentanglement is a fast-growing process for manufacturing non-woven fabrics. In this process, multiple fine jets of highly pressurised water are directed towards a fibreweb composed initially of loose fibres, supported by the forming belt. The impact of the jets causes fibre entanglement in the fibreweb and produces an integrated fabric with desired aesthetics. It is important that, at the end of the process, the fibreweb could be easily separated from the forming wires. In this paper, the peeling force required for the separation of the hydroentangled fabric from the forming wires is measured experimentally. Numerical simulations of the hydroentanglement process are also carried out to predict the probability of fibres to be pushed in the knuckles of the forming wires. The fibres that get caught in the knuckles are mainly responsible for the peeling force of the fabric from the forming wires. The fibreweb is modelled as a porous layer, which is supported by forming wires. By correlating experimental results with simulations, a mathematical model, which is based on simulating average vorticity around the forming wires, is developed to predict the peeling force. The effect of the thickness of the fibreweb layer on the peeling force is investigated. 相似文献
12.
13.
该文对机械面设计采用变化重平组织、绑紧采用纬线自接结方式的三层成形网设计进行了探讨,为新三层成形网的设计和开发提供一种有益思路。 相似文献
14.
为了研究正交机织物的实际结构,采用玻璃纤维在剑杆织机上织制了纬纱接结的6层经纱5层纬纱的正交机织物,然后利用VARI工艺与聚酯树脂复合,制成了复合材料板材试样,并在显微镜下观测纱线的形状。研究发现:三维正交机织物的经、纬纱基本呈直线状态,接结纬纱是曲线与直线组合的形状,且形状与在织物中的位置有关,越靠近织物中央,接结纬纱的直线部分越短;接结纬纱使其限定的经纱产生聚集现象,在复合材料中产生贫富树脂区,接结纬纱形状的变化也使织物的结构不均匀。对织造过程的分析表明,造成接结纬纱形状变化的原因是织物形成过程中接结纬纱的滑动,从织物边部到中央,接结纬纱的滑动阻力逐渐增大,接结纬纱的张力也逐渐增大。 相似文献
15.
16.
为提高F-12芳纶织物与橡胶之间的粘结性能,采用环氧树脂和偶联剂A187对F-12芳纶织物进行改性。通过成膜分析确定出环氧树脂的最佳用量;通过改性后F-12芳纶织物的浸水高度以及浸渍间苯二酚-甲醛树脂乳液后的拉伸强度和断裂强度测试,确定出偶联剂A187的最佳用量。在此基础上,对改性后的F-12芳纶织物进行硫化成型,测试织物与橡胶的剥离强度确定出最佳改性工艺。结果表明:环氧树脂用量为25%(o.w.f),偶联剂A187用量为1.2%(o.w.f)时,制备的F-12芳纶织物轻薄输送带的综合性能最佳;改性后浸水高度值最低的F-12芳纶织物制备的轻薄输送带的剥离强力达到最高,为12.1 N/mm,其剥离强度高于行业标准;制备的单层铺层输送带的扯断强力为6 495.25 N,断裂伸长率为13%,双层铺层输送带的扯断强力为14 493.25 N,断裂伸长率为14%。 相似文献
17.
角度联锁三维机织物的设计与生产 总被引:7,自引:4,他引:7
介绍了三维织物在国内外的应用及角度联锁三维机织物及其变化织物的特点与使用情况,重点对角度联锁三维机织物及其变化织物(加有衬型纱的角度联锁织物和正交机织物)的交织原理进行分析,对其织物组织结构、织物组织的设计要点以及织物形成过程进行了探讨. 相似文献
18.
采用仿形织造方法织造带织物,并用该带织物层叠缠绕生产玻璃钢管道是一种新方法。在缠绕成型过程中,为了使管道的成型性良好,需要对缠绕角度、经纱长度、织物幅宽等进行设计,同时选择成型效果好的织物组织。试验结果表明:圆直管道预成型织物的缠绕角取决于织物幅宽、缠绕层数和管道直径;织物的经纱长度不等,按照一定的规律随缠绕层数的增加而增加;2/2斜纹组织织物的成型效果较好。 相似文献
19.
Magdi ElMessiry 《纺织学会志》2017,108(9):1618-1627
The manufacturing of composites often requires transformation of 2-D fabrics into various structural 3-D shapes through preform processing without over straining of the yarns or wrinkling. Sheet forming of woven fabric composite by combined cyclic stretch and deep drawing was suggested. In order to prevent the wrinkling, the geometrical and mechanical properties of fabric should be chosen to get the final form of the prepregs beforehand. Geometrical investigation of the final bagged form dimensions are based on geometrical aspects of the wrapping of the fabric. In this study, an approach was proposed to form the reinforcement fabric composite through the dynamic bagging of the fabric by the application of cyclic stretching on the fabric during formation of 3-D reinforcement structure in hot environment. The dimensions of the flat fabric were calculated and the parameters of the forming process analyzed in two cases: hemisphere and flat top cone shape. 相似文献