Energy recovery from grass of urban roadside verges by anaerobic digestion and combustion after pre-processing

Grass from urban roadside verges is a potential, though widely unused, resource for bioenergy recovery. Two possible bioenergy recovery techniques were tested, i.e. i) direct anaerobic digestion of the whole parent material and ii) the “integrated generation of solid fuel and biogas from biomass” (IFBB) procedure, which divides biomass into a press fluid and a press cake by mashing and mechanical dewatering. Biomass yield, chemical composition and canopy height of biomass, contribution of functional groups, fermentation characteristics of silage and press fluids, as well as characteristics of the produced solid fuel was investigated, applying a 4-cut management for anaerobic digestion, a 2-cut management for IFBB and an 8 times mulching as a reference. Mean annual biomass yield (2013 and 2014) was 3.24, 3.33 and 5.68 t dry matter ha⁻¹ for the mulching, 4-cut management and 2-cut management, respectively. Yields were higher in 2014 due to more favourable weather conditions. Fibre concentration was higher in material of the 2-cut management than in the 4-cut management, however, methane yield of the corresponding silages was the same. Highest methane yield was gained from press fluids with 292 l_N kg⁻¹ volatile solids. The press cake had a lower heating value of 16 MJ kg⁻¹ dry matter and a K₂O/CaO index of 0.51–0.88. Gross energy output was 26.4 GJ ha⁻¹ for anaerobic digestion and 84.4 GJ ha⁻¹ for IFBB. Thus, an altered roadside verge management with reduced cutting frequency might allow a significant energy recovery and improved ecosystem services, i.e. increased biodiversity.     

Supercritical water gasification of timothy grass as an energy crop in the presence of alkali carbonate and hydroxide catalysts

This study is focused on identifying the candidature of timothy grass as an energy crop for hydrogen-rich syngas production through supercritical water gasification. Timothy grass was gasified in supercritical water to investigate the impacts of temperature (450–650 °C), biomass-to-water ratio (1:4 and 1:8) and reaction time (15–45 min) in the pressure range of 23–25 MPa. The impacts of carbonate catalysts (e.g., Na₂CO₃ and K₂CO₃) and hydroxide catalysts (e.g., NaOH and KOH) at variable mass fractions (1–3%) were examined to maximize hydrogen yields. In the non-catalytic gasification of timothy grass, highest hydrogen (5.15 mol kg⁻¹) and total gas yields (17.2 mol kg⁻¹) with greater carbon gasification efficiency (33%) and lower heating value (2.21 MJ m⁻³) of the gas products were obtained at 650 °C with 1:8 biomass-to-water ratio for 45 min. However, KOH at 3% mass fraction maximized hydrogen and total gas yields up to 8.91 and 30.6 mol kg⁻¹, respectively. Nevertheless, NaOH demonstrated highest carbon gasification efficiency (61.3%) and enhanced lower heating value of the gas products (4.68 MJ m⁻³). Timothy grass biochars were characterized through Fourier transform infrared spectroscopy, Raman spectroscopy and scanning electron microscopy to understand the behavior of the feedstock to rising temperature and reaction time. The overall findings suggest that timothy grass is a promising feedstock for hydrogen production via supercritical water gasification.     

Changes in feedstock quality in willow chip piles created in winter from a commercial scale harvest

Storage and handling are important facets of biomass logistics because there are associated costs and biomass properties can change significantly as material proceeds through the supply chain. Thus, this aspect of biomass supply systems requires continued study. Shrub willow chips were harvested, and used to create six piles that each contained between 10 and 22 Mg (fresh biomass). Material was monitored for several months in temporary storage to assess changes in biomass quality (moisture, ash and energy content). Internal pile temperatures increased due to biological activity and conditions within a pile quickly differentiated based on location (shell, core, top, and side). Mean moisture content increased from 42 to 47% (mass fraction) between harvest and delivery of the chips, but ranged between 37 and over 60% over the next three months depending on pile location with the shell generally drier than the core. Mean ash content increased 1 to 2% points (mass fraction) between harvesting, reloading and delivery to the trial location, but became more variable during storage. Higher heating values (HHV) were stable between 18.6 and 19.0 MJ kg⁻¹ over the six months, but lower heating values (LHV) ranged between 8.6 and 11.7 MJ kg⁻¹ and mirrored changes in moisture content. There was minimal change in chip quality over two months, but quality became more variable over longer time periods. This period could be extended, and negative effects on chip quality could be mitigated, by improving storage methods, blending different types of chips, or employing pretreatments.     

Enhanced substrate degradation and methane yield with maleic acid pre-treatments in biomass crops and residues

Organic acids are envisaged as alternative catalysts to strong mineral acids, in pre-treatment of ligno-cellulosic biomass for anaerobic digestion (AD). To evaluate this hypothesis, an untreated control and four pre-treatments (25 °C for 24 h) involving two levels of maleic acid (34.8 and 69.6 kg m⁻³), alone and combined with sulphuric acid (4 kg m⁻³), were studied in three agricultural substrates: Arundo (aka giant reed), Barley straw and B133 fibre sorghum. Methane production was assessed in a batch AD assay (35 °C for 51 days) with 4 g L⁻¹ of volatile solid (VS) load. Fibre composition and structure were investigated through chemical analysis and Fourier transform infrared (FTIR) spectrometry. Arundo and B133 that were the most and least recalcitrant substrate, respectively, staged the highest and lowest increase in methane with high maleic acid: +62% over 218 cm³ g⁻¹ of VS in untreated Arundo; +36% over 284 cm³ g⁻¹ of VS in untreated B133. Barley straw showed an intermediate behaviour (+41% over 269 cm³ g⁻¹ of VS). H₂SO₄ addition to maleic acid did not improve CH₄ output. The large increase in methane yield determined by pre-treatments was reflected in the concurrent decrease of fibre (between 14 and 39% depending on fibrous component). Based on FTIR spectra, bands assigned to hemicellulose and cellulose displayed lower absorbance after pre-treatment, supporting the hypothesis of solubilisation of structural carbohydrates and change in fibre structure. Hence, maleic acid was shown a suitable catalyst to improve biodegradability of ligno-cellulosic biomass, especially in recalcitrant substrates as Arundo.     

Sickle bush (Dichrostachys cinerea L.) field performance and physical–chemical property assessment for energy purposes

The sickle bush (Dichrostachys cinerea (L.) Wight & Arn.) comprises a woody legume shrub which is widely distributed throughout of the tropical areas of Africa, Asia and Oceania, being found as well in Cuba where it represents a difficult to control invasive plant. It holds great silvopasture and energy crop potentials. In southwestern Spain a two year field trial was conducted contemplating also another six hardwood taxa commonly used as energy crops. The sickle bush above ground dry biomass fraction was 60.4%; sickle bush displayed a high transpiration rate during hot days (3.02 kg m⁻² d⁻¹ to 6.82 kg m⁻² d⁻¹); cold winter temperatures (<−2 °C) together with hot and dry summer air (<20% relative humidity) committed survival and growth. The physical-chemical wood properties and the pellets thereof derived were analyzed and compared to those of the other energy crop taxa. The within other woody species normal chemical composition range coupled to a high wood density and energetic use properties (19.2 MJ kg⁻¹ higher heating value, 29 g kg⁻¹ ash content) all allow for an industrial use. Pellets evidenced also good physical and mechanical properties (690 kg m⁻³ bulk density, 42 g kg⁻¹ moisture content). However, the mechanical durability (93.9%) was slightly less than that required by the non-industrial use standards, therefore further improvements should be studied. All of the above could encourage scrubland cuts in Cuba as a mechanical control method, in addition to the expansion of plantations within of their tropical climate based natural habitats.     

Compositional differences among upland and lowland switchgrass ecotypes grown as a bioenergy feedstock crop

Feedstock quality mainly depends upon the biomass composition and bioenergy conversion system being used. Higher cellulose and hemicellulose concentrations are desirable for biochemical conversion, whereas higher lignin is favored for thermochemical conversion. The efficiency of these conversion systems is influenced by the presence of high nitrogen and ash concentrations. Switchgrass (Panicum virgatum L.) varieties are classified into two ecotypes based on their habitat preferences, i.e., upland and lowland. The objectives of this study were to quantify the chemical composition of switchgrass varieties as influenced by harvest management, and to determine if ecotypic differences exist among them. A field study was conducted near Ames, IA during 2012 and 2013. Upland (‘Cave-in-Rock’, ‘Trailblazer’ and ‘Blackwell’) and lowland switchgrass varieties (‘Kanlow’ and ‘Alamo’) were grown in a randomized block design with six replications. Six biomass harvests were collected at approximately 2-week intervals each year. In both years, delaying harvest increased cellulose, hemicellulose and lignin concentrations while decreasing nitrogen and ash concentrations in all varieties. On average, Kanlow had the highest cellulose and hemicellulose concentration (354 and 321 g kg⁻¹ DM respectively), and Cave-in-Rock had the highest lignin concentration (33 g kg⁻¹ DM). The lowest nitrogen and ash concentrations were observed in Kanlow (14 and 95 g kg⁻¹ DM respectively). In general, our results indicate that delaying harvest until fall improves feedstock quality, and ecotypic differences do exist between varieties for important feedstock quality traits. These findings also demonstrate potential for developing improved switchgrass cultivars as bioenergy feedstock by intermating lowland and upland ecotypes.     

Optimization of mechanical pre-treatment of Laminariaceae spp. biomass-derived biogas

Macroalgae have not met their full potential to date as biomass for the production of energy. One reason is the high cost associated with the pretreatment which breaks the biomass's crystalline structure and better exposes the fermentable sugars to anaerobes. In the attempt to overcome this technological barrier, the performance of a Hollander beater mechanical pretreatment is assessed in this paper. This pretreatment has been applied to a batch of Laminariaceae biomass and inoculated with sludge from a wastewater treatment plant. The derived biogas and methane yields were used as the responses of a complex system in order to identify the optimal system input variables by using the response surface methodology (RSM). The system's inputs considered are the mechanical pretreatment time (5–15 min range), the machine's chopping gap (76–836 μm) and the mesophilic to thermophilic range of temperatures (30–50 °C). The mechanical pretreatment was carried out with the purpose of enhancing the biodegradability of the macroalgal feedstock by increasing the specific surface area available during the anaerobic co-digestion. The pretreatment effects on the two considered responses are estimated, discussed and optimized using the tools provided by the statistical software Design-Expert v.8. The best biogas yield of treated macroalgae was found at 50 °C after 10 min of treatment, providing 52% extra biogas and 53% extra methane yield when compared to untreated samples at the same temperature conditions. The highest biogas rate achieved by treating the biomass was 685 cc gTS⁻¹, which is 430 cc gTS⁻¹ in terms of CH₄ yield.     

Characterization,pretreatment and saccharification of spent seaweed biomass for bioethanol production using baker's yeast

Seaweeds are marine macroalgae found abundantly and viewed as potential source of phycocolloids to produce biofuel. In this study, seaweed spent biomass obtained from alginate production industry and biomass obtained after pigment extraction were found to contain a considerable amount of phycocolloids. These two spent biomasses were investigated for the production of ethanol. In this study, the red seaweed spent biomass of Gracilaria corticata var corticata showed higher content of polysaccharide (190.71 ± 30.67 mg g⁻¹ dry weight) than brown seaweed spent biomass (industrial) (136.28 ± 30.09 mg g⁻¹ dry weight). Hydrolysis of spent biomasses with different concentrations of sulfuric acid (0.1%, 0.5% and 1%) was also investigated. Brown seaweed spent biomass and red seaweed spent biomass exhibited high amount of sugar in 0.5% and 1% sulfuric acid treatment, respectively. Proximate and ultimate composition of seaweed spent biomasses were analysed for energy value. The FT-Raman spectra exhibited similar stretches for both acid hydrolysed spent biomasses with their respective standards. Ethanol produced through a fermentation process using spent hydrolysates with baker's yeast at pH 5.3 was found to be significant. The ethanol yield from brown seaweed spent biomass and red seaweed spent biomass was observed to be 0.011 g g⁻¹ and 0.02 ± 0.003 g g⁻¹ respectively, when compared with YPD (0.42 ± 0.03 g g⁻¹) and d-galactose (0.37 ± 0.04 g g⁻¹) as standard on day 4. The present study revealed the possibility of effective utilization of spent biomass from seaweed industry for ethanol production.     

Combined ethanol and methane production from switchgrass (Panicum virgatum L.) impregnated with lime prior to steam explosion

Pretreatments are crucial to achieve efficient conversion of lignocellulosic biomass to soluble sugars. In this light, switchgrass was subjected to 13 pretreatments including steam explosion alone (195 °C for 5, 10 and 15 min) and after impregnation with the following catalysts: Ca(OH)₂ at low (0.4%) and high (0.7%) concentration; Ca(OH)₂ at high concentration and higher temperature (205 °C for 5, 10 and 15 min); H₂SO₄ (0.2% at 195 °C for 10 min) as reference acid catalyst before steam explosion. Enzymatic hydrolysis was carried out to assess pretreatment efficiency in both solid and liquid fraction. Thereafter, in selected pretreatments the solid fraction was subjected to simultaneous saccharification and fermentation (SSF), while the liquid fraction underwent anaerobic digestion (AD). Lignin removal was lowest (12%) and highest (35%) with steam alone and 0.7% lime, respectively. In general, higher cellulose degradation and lower hemicellulose hydrolysis were observed in this study compared to others, depending on lower biomass hydration during steam explosion. Mild lime addition (0.4% at 195 °C) enhanced ethanol in SSF (+28% than steam alone), while H₂SO₄ boosted methane in AD (+110%). However, methane represented a lesser component in combined energy yield (ethanol, methane and energy content of residual solid). Mild lime addition was also shown less aggressive and secured more residual solid after SSF, resulting in higher energy yield per unit raw biomass. Decreased water consumption, avoidance of toxic compounds in downstream effluents, and post process recovery of Ca(OH)₂ as CaCO₃ represent further advantages of pretreatments involving mild lime addition before steam explosion.     

GIS-based assessment of sustainable crop residue potentials in European regions

In this paper a novel model based on a geographic information system (GIS) is presented for the assessment of sustainable crop residue potentials. The approach is applied to analyse the amount and the spatial distribution (1 km × 1 km grid cells) of cereal straw, root crop and oil plant residues for five European regions, considering spatially differentiated environmental sustainability issues, i.e. organic carbon content in topsoil, soil erodibility, and protected areas. The maximum sustainable residue potential varies strongly between the regions and residue types. In the scenarios Basis and Restrict, it accounts for 45–59% and 24–48% of the theoretical potential respectively without considering competing uses. Among the crop residues, cereal straw shows the highest energy potential in all regions under investigation. In terms of wet mass it accounts for 3.7 Mio. t_wet/a in North Rhine-Westphalia, 1.6 Mio. t_wet/a in Île-the-France, 1.2 Mio. t_wet/a in Wallonia, 0.9 Mio. t_wet/a in West Midlands, and 0.3 Mio. t_wet/a in South Netherlands (scenario Basis). Our survey shows that spatially differentiated potential estimations and the inclusion of crop residues other than cereal straw are urgently needed to improve the present rough estimations for crop residues which can be used in a sustainable way. The rather high spatial resolution of our analyses particularly allows for the support of regional stakeholders and prospective investors when it comes to questions of regional availability of biomass resources, transport distances to biomass conversion plants, and identification of suitable plant sites and sizes, respectively.     

Assessing sustainable forest biomass potential and bioenergy implications for the northern Lake States region,USA

Forestlands in the United States have tremendous potential for providing feedstocks necessary to meet emerging renewable energy standards. The Lake States region is one area recognized for its high potential of supplying forest-derived biomass; however, the long-term availability of roundwood harvests and associated residues from this region has not been fully explored. Better distribution and temporal availability estimates are needed to formulate emerging state policies regarding renewable energy development. We used a novel predictive methodology to quantify sustainable biomass availability and likely harvest levels over a 100-year period in the Lake States region. USDA Forest Inventory and Analysis estimates of timberland were combined with published growth and yield models, and historic harvest data using the Forest Age Class Change Simulator (FACCS) to generate availability estimates. Monte-Carlo simulation was used to develop probability distributions of biomass harvests and to incorporate the uncertainty of future harvest levels. Our results indicate that 11.27–15.71 Mt y⁻¹ dry roundwood could be sustainably harvested from the Lake States. Assuming 65% collection rate, 1.87–2.62 Mt y⁻¹ residue could be removed, which if substituted for coal would generate 2.12–2.99 GW h of electricity on equivalent energy basis while reducing GHG (CO₂e) emission by 1.91–2.69 Mt annually. In addition to promoting energy security and reducing GHG emissions, forest residues for energy may create additional revenues and employment opportunities in a region historically dependent on forest-based industries.     

Steam explosion pretreatment and enzymatic saccharification of duckweed (Lemna minor) biomass

Our previous research has shown that duckweed is potentially an ideal feedstock for the production of biofuels because it can be effectively saccharified enzymatically. Here we report the results of experiments in which duckweed was pre-treated by steam explosion prior to enzyme digestion. A range of temperatures, from 130 to 230 °C with a fixed retention time of 10 min, were employed. The best pretreatment conditions were 210 °C for 10 min; these conditions produced the highest amount of water-soluble material (70%), the greatest levels of starch solubilisation (21%) and hemicellulose and pectic polysaccharides degradation (60%). The use of these steam explosion conditions enabled large reductions in the concentrations of enzymes required for effective saccharification. The amount of Celluclast required was reduced from 100 U (4.35 FPU) g⁻¹ substrate to 20 U g⁻¹ substrate, and additional beta-glucosidase was reduced from 100 to 2 U g⁻¹ substrate.     

Estimating sustainable crop residue removal rates and costs based on soil organic matter dynamics and rotational complexity

The government of Ontario, Canada, has committed to stopping the use of coal for electrical generation by 2014 and agricultural biomass is being considered as replacement. However, there is limited information on whether the annual 2 million Mg of biomass required to replace coal could be sustainably supplied by agriculture and at what costs. This study assesses the sustainable availability and the farm-gate break-even cost of residue biomass from three crops (corn, soybean and winter wheat) grown under two common rotation scenarios in Ontario. Sustainably removable residue (SRR) rates are determined using a five-step approach that accounts for maintenance soil organic matter (MSOM) in the presence of yield and rotation variations across counties. Under typical SOM formation and decomposition conditions and assuming typical corn-soybean and corn-soybean-winter wheat rotation scenarios, about 1.1 million Mg of residue could be sustainably removed each year, primarily from the major agricultural counties in the province. While rotational complexity enhances SRR, the inclusion of soybean decreases available residue compared to corn and winter wheat. The break-even price for crop residues, representing the minimum price necessary to cover all variable and fixed costs for the farmer, is between $57 Mg⁻¹ and $87 Mg⁻¹. However, the actual amount supplied for each biomass price depends critically on the opportunity costs associated with not growing typical crops in the conventional manner.     

Mild alkaline pre-treatments loosen fibre structure enhancing methane production from biomass crops and residues

Three ligno-cellulosic substrates representing varying levels of biodegradability (giant reed, GR; fibre sorghum, FS; barley straw, BS) were combined with mild alkaline pre-treatments (NaOH 0.05, 0.10 and 0.15 N at 25 °C for 24 h) plus untreated controls, to study pre-treatment effects on physical-chemical structure, anaerobic digestibility and methane output of the three substrates. In a batch anaerobic digestion (AD) assay (58 days; 35 °C; 4 g VS l⁻¹), the most recalcitrant substrate (GR) staged the highest increase in cumulative methane yield: +30% with NaOH 0.15 N over 190 ml CH₄ g⁻¹ VS in untreated GR. Conversely, the least recalcitrant substrate (FS) exhibited the lowest gain (+10% over 248 ml CH₄ g⁻¹ VS), while an intermediate behaviour was shown by BS (+15% over 232 ml CH₄ g⁻¹ VS). Pre-treatments speeded AD kinetics and reduced technical digestion time (i.e., the time needed to achieve 80% methane potential), which are the premises for increased production capacity of full scale AD plants. Fibre components (cellulose, hemicellulose and acid insoluble lignin determined after acid hydrolysis) and substrate structure (Fourier transform infra-red spectroscopy and scanning electron microscopy) outlined reductions of the three fibre components after pre-treatments, supporting claims of loosened binding of lignin with cellulose and hemicellulose. Hence, mild alkaline pre-treatments were shown to improve the biodegradability of ligno-cellulosic substrates to an extent proportional to their recalcitrance. In turn, this contributes to mitigate the food vs. fuel controversy raised by the use of whole plant cereals (namely, maize) as feedstocks for biogas production.     

Ni/Ru–Mn/Al2O3 catalysts for steam reforming of toluene as model biomass tar

The catalytic steam reforming of the major biomass tar component, toluene, was studied over two commercial Ni-based catalysts and two prepared Ru–Mn-promoted Ni-base catalysts, in the temperatures range 673–1073 K. Generally, the conversion of toluene and the H₂ content in the product gas increased with temperature. A H₂-rich gas was generated by the steam reforming of toluene, and the CO and CO₂ contents in the product gas were reduced by the reverse Boudouard reaction. A naphtha-reforming catalyst (46-5Q) exhibited better performance in the steam reforming of toluene at temperatures over 873 K than a methane-reforming catalyst (Reformax 330). Ni/Ru–Mn/Al₂O₃ catalysts showed high toluene reforming performance at temperatures over 873 K. The results indicate that the observed high stability and coking resistance may be attributed to the promotional effects of Mn on the Ni/Ru–Mn/Al₂O₃ catalyst.     

Growth,yield, fiber content and lodging resistance in eight varieties of Cenchrus purpureus (Schumach.) Morrone intended as energy crop

Growth, biomass yield, fiber content and lodging resistance were studied, during a six month growth period, for eight varieties of Cenchrus purpureus, intended as energy crop, in Veracruz, Mexico. Then, only yield at day 182 was assessed for two additional years. The varieties were: CT115 (CT), African Cane (AC), Taiwan (TAI), King Grass (KG), Vruckwona (VRU), Roxo (RX), OM22 (OM) and Cameroon (CAM). Local weather is warm and sub-humid, historical data for monthly average temperature and annual rainfall were 25.8 °C and 1142 mm, respectively. Height, diameter and light interception were measured monthly from day 65–185. At day 185, biomass yield and tiller density were measured. Number of lying tillers was counted to estimate lodging resistance. Cellulose and hemicellulose content were estimated in leaf and stem. No differences were found for dry matter yield or stem yield at day 185 in the first year. Regarding the next two years, TAI yielded above CT, OM or ROX. Average dry matter yield was higher in the second year than in the establishment cycle (38.6 vs 21.1 Mg ha⁻¹), but decreased in the third year (32.2 Mg ha⁻¹). In both stem and whole plant, AC and KG showed higher hemicellulose content than RX, OM or CT; while AC and VRU had higher cellulose than RX in stem, or than CT in the whole plant. Furthermore, varieties AC, KG, VRU and TAI were resistant to lodging and had a higher fiber content, so they are recommended as energetic crops.     

Biopower from direct firing of crop and forestry residues in China: A review of developments and investment outlook

This paper reviews developments in the direct-fired biomass power sector and provides an up to date investment outlook by calculating the Net Present Value of new investments, and the appropriate level of Feed-in-Tariff needed to stimulate future investment. An overview is provided of support policies, historical growth in installations, and main market players. A number of data sources is combined to build a database with detailed information of individual biopower projects. This data is used to describe technological and market trends, which are used in a cash flow model to calculate the NPV of a typical project. The NPV for new projects is estimated to be negative, and investment should be expected to stall without proper policy intervention. Increasing fuel prices, local competition over biomass fuel resources, lower than expected operational performance and a downturn in carbon markets have deteriorated the investment outlook. In order to ensure reasonable profitability, the Feed-In-Tariff should be increased, from the current level of 90.9 € MWh⁻¹, to between 97 and 105 € MWh⁻¹. Where possible, government organizations should help organize demand for the supply of heat. Local rural energy bureaus may help organize supply networks for biomass fuels throughout the country, in order to reduce seasonal and local fuel scarcity and price fluctuations.     

An oil palm-based biorefinery concept for cellulosic ethanol and phytochemicals production: Sustainability evaluation using exergetic life cycle assessment

In this study, thermo-environmental sustainability of an oil palm-based biorefinery concept for the co-production of cellulosic ethanol and phytochemicals from oil palm fronds (OPFs) was evaluated based on exergetic life cycle assessment (ExLCA). For the production of 1 tonne bioethanol, the exergy content of oil palm seeds was upgraded from 236 MJ to 77,999 MJ during the farming process for OPFs production. Again, the high exergy content of the OPFs was degraded by about 62.02% and 98.36% when they were converted into cellulosic ethanol and phenolic compounds respectively. With a total exergy destruction of about 958,606 MJ (internal) and 120,491 MJ (external or exergy of wastes), the biorefinery recorded an overall exergy efficiency and thermodynamic sustainability index (TSI) of about 59.05% and 2.44 per tonne of OPFs' bioethanol respectively. Due to the use of fossil fuels, pesticides, fertilizers and other toxic chemicals during the production, the global warming potential (GWP = 2265.69 kg CO₂ eq.), acidification potential (AP = 355.34 kg SO₂ eq.) and human toxicity potential (HTP = 142.79 kg DCB eq.) were the most significant environmental impact categories for a tonne of bioethanol produced in the biorefinery. The simultaneous saccharification and fermentation (SSF) unit emerged as the most exergetically efficient (89.66%), thermodynamically sustainable (TSI = 9.67) and environmentally friendly (6.59% of total GWP) production system.     

Sweet sorghum as a whole-crop feedstock for ethanol production

The potential of sweet sorghum as an alternative crop for ethanol production was investigated in this study. Initially, the enzymatic hydrolysis of sorghum grains was optimized, and the hydrolysate produced under optimal conditions was used for ethanol production with an industrial strain of Saccharomyces cerevisiae, resulting in an ethanol concentration of 87 g L⁻¹. From the sugary fraction (sweet sorghum juice), 72 g L⁻¹ ethanol was produced. The sweet sorghum bagasse was submitted to acid pretreatment for hemicellulose removal and hydrolysis, and a flocculant strain of Scheffersomyces stipitis was used to evaluate the fermentability of the hemicellulosic hydrolysate. This process yielded an ethanol concentration of 30 g L⁻¹ at 23 h of fermentation. After acid pretreatment, the remaining solid underwent an alkaline extraction for lignin removal. This partially delignified material, known as partially delignified lignin (PDC), was enriched with nutrients in a solid/liquid ratio of 1 g/3.33 mL and subjected to simultaneous saccharification and fermentation (SSF) process, resulting in an ethanol concentration of 85 g L⁻¹ at 21 h of fermentation. Thus, from the conversion of starchy, sugary and lignocellulosic fractions approximately 160 L ethanol.ton⁻¹ sweet sorghum was obtained. This amount corresponds to 13,600 L ethanol.ha⁻¹.     

Effects of delayed winter harvest on biomass yield and quality of napiergrass and energycane

Napiergrass (Cenchrus purpureus (Schumach.) Morrone) and energycane (Saccharum hyb.) are perennial grasses that are well-suited for biomass production in the southeastern USA. The purpose of this study was to determine the effects of delayed winter harvest on biomass yield and quality of these grasses. The study was conducted on two adjacent sites near Midville, GA. Each site used a split-plot design with four replications, with species as the main plot, and harvest times (December, January, or February) as sub-plots. Dry matter (DM) yields were measured by mechanical harvesting, and a sample of biomass was taken from each harvest for determination of ethanol production by simultaneous saccharification and fermentation (SSF). Biomass moisture, N, P, K, and ash mass fractions were also measured. Energycane DM yields were stable from December (46.8 Mg ha⁻¹) to January (42.9 Mg ha⁻¹), but then declined (36.8 Mg ha⁻¹), while napiergrass yields declined sharply from December (47.0 Mg ha⁻¹) to January (35.0 Mg ha⁻¹). Napiergrass moisture mass fraction was reduced by an average of 18% in February harvests compared to December. Mass fractions of N, K, and ash tended to decrease with later harvesting, but sometimes increased due to changes in biomass composition. Delaying harvest of napiergrass from December to January reduced N removal by an average of 144 kg ha⁻¹, while delaying harvest of energycane to February reduced N removal by an average of 54 kg ha⁻¹. In SSF, later-harvested energycane produced less ethanol per unit of DM while napiergrass was less affected by harvest date.