Blends of poly(vinyl chloride) with α‐methylstyrene‐acrylonitrile‐butadiene‐styrene copolymer: Thermal properties,mechanical properties,and morphology

Binary blends of poly(vinyl chloride) (PVC) with α‐methylstyrene‐acrylonitrile‐butadiene‐styrene copolymer (AMS‐ABS) were prepared via melt blending. A single glass transition temperature (T_g) was observed by differential scanning calorimetry, thus indicating that PVC is miscible with the α‐methylstyrene‐acrylonitrile‐styrene in AMS‐ABS. The results from attenuated total reflection Fourier transform infrared spectra indicated that specific strong interactions were not available in the blends. With increasing amounts of AMS‐ABS, both heat distortion temperature and thermal stability were increased considerably. With regard to mechanical properties, flexural and tensile properties decreased with increasing AMS‐ABS content. A synergism was observed in impact strength. The morphology of both impact‐fractured and tensile‐fractured surfaces, observed by scanning electron microscopy, correlated well with the mechanical properties. It is suggested that there was a transition of fracture mechanisms with the changing composition of the binary blends—from shear yielding for blends rich in PVC to cavitation for blends rich in AMS‐ABS. J. VINYL ADDIT. TECHNOL., 19:1–10, 2013. © 2013 Society of Plastics Engineers     

Toughening modification of poly(vinyl chloride)/ α‐methylstyrene‐acrylonitrile‐butadiene‐styrene copolymer blends via adding chlorinated polyethylene

In this study, poly (vinyl chloride) (PVC)/α‐methylstyrene‐acrylonitrile‐butadiene‐styrene copolymer (AMS‐ABS) (70/30)/chlorinated polyethylene (CPE) ternary blends was prepared. With the addition of CPE, it did not exert a negative influence in both the glass transition temperature and heat distortion temperature. Thermogravimetric analysis showed that addition of CPE did not play a negative role in the thermal stability. With regard to mechanical properties, high toughness was observed combined with the decrease in tensile strength and flexural strength. With the addition of 15 phr CPE, the impact strength increased by about 21.0 times and 8.5 times in comparison with pure PVC and PVC/AMS‐ABS (70/30) blends, respectively. The morphology correlated well with the impact strength. It was also suggested from the morphology that shear yielding was the major toughening mechanisms for the ternary blends. And there existed a change in the fibril structures that are observed in scanning electron microphotographs. Our present study shows that combination of AMS‐ABS and CPE improves the toughness without sacrificing the heat resistance, and the value of notched impact strength can be enhanced to the same level of super‐tough nylon. POLYM. ENG. SCI., 54:378–385, 2014. © 2013 Society of Plastics Engineers     

Toughening modification of (Acrylonitrile‐styrene‐acrylic copolymer)/(α‐Methylstyrene‐acrylonitrile copolymer) binary blend via using different impact modifiers

In this work, different impact modifiers such as acrylic resin impact modifier, chlorinated polyethylene (CPE), nitrile rubber, powdered nitrile rubber, and hydrogenated nitrile rubber, were chosen to improve the toughness of (acrylonitrile‐styrene‐acrylic copolymer)/(α‐methylstyrene‐acrylonitrile copolymer) (ASA/α‐MSAN) binary blend. The blend ratios of the ASA/(α‐MSAN)/(impact modifier) ternary system were 30/70/20 and 70/30/20 by mass, respectively. The results showed that the impact strength significantly increased, nearly 30 times (22.59 kJ·m^?2, 22.26 kJ·m^?2, and 25.24 kJ·m^?2) compared with that of control samples (0.80 kJ·m^?2) when nitrile rubber, powdered nitrile rubber, or hydrogenated nitrile rubber was added to the ASA/(α‐MSAN) (30/70) matrix, respectively. Moreover, the impact strength of ASA/(α‐MSAN) (70/30) was dramatically enhanced to 46 kJ·m^?2 with the addition of 20 parts by weight per hundred parts of resin of chlorinated polyethylene. The toughness of ASA/(α‐MSAN) with or without impact modifiers was also characterized via fracture energy calculated from stress‐strain curves. The results were perfectly consistent with that of impact strength. The results of dynamic mechanical analysis demonstrated the existence of α‐MSAN (glass transition temperature at approximately 140°C). The heat distortion temperature was barely changed, indicating the addition of impact modifiers barely affects the heat resistance. J. VINYL ADDIT. TECHNOL., 22:326–335, 2016. © 2014 Society of Plastics Engineers     

Toughness,dynamic mechanical property,and morphology of polyvinylchloride/acrylonitrile‐styrene‐butyl acrylate blends

Acrylonitrile‐styrene‐butyl acrylate (ASA) graft copolymers with different acrylonitrile (AN) contents, the core‐shell ratio, and tert‐dodecyl mercaptan (TDDM) amounts were synthesized by seed emulsion polymerization. Polyvinylchloride (PVC)/ASA blends were prepared by melt blending ASA graft copolymers with PVC resin. Then the toughness, dynamic mechanical property, and morphology of the PVC/ASA blends were investigated. The results indicated that the impact strength of the PVC/ASA blends increased and then decreased with the increase of the AN content in poly(styrene‐co‐acrylonitrile (SAN) copolymer, and increased with the increase of the core‐shell ratio of ASA. It was shown that brittle‐ductile transition of PVC/ASA blends was dependent on poly(butyl acrylate) (PBA) rubber content in blends and independent of AN content in SAN copolymer. The introduction of TDDM made the toughness of PVC/ASA blends poor. Dynamic mechanical analysis (DMA) curves exhibited that PVC and SAN copolymers were immiscible over the entire AN composition range. From scanning electron microscopy (SEM), it was found that the dispersion of ASA in PVC/ASA blends was dependent on the AN content in SAN copolymer and TDDM amounts. J. VINYL ADDIT. TECHNOL., 22:43–50, 2016. © 2014 Society of Plastics Engineers     

Mechanical and thermal properties of (acrylonitrile‐styrene‐acrylic)/(α‐methylstyrene‐acrylonitrile) binary blends

In this work, (acrylonitrile‐styrene‐acrylic)/(α‐methylstyrene‐acrylonitrile) copolymer (ASA/α‐MSAN) binary alloy was prepared with different composition ratios via melt blending. This work mainly focused on improving the heat resistance of ASA. According to the results of dynamic mechanical thermal analysis, the binary blends exhibited three glass transition temperatures (T_gs) and the shift of the T_gs indicated the partial miscibility of binary blends. This partial miscibility maintained the high T_g of α‐MSAN, which led to the outstanding heat resistance of binary blends. Furthermore, heat distortion temperature also showed that the heat resistance of binary blends was significantly enhanced with the addition of α‐MSAN. However, the introduction of this highly rigid polymer also brought with it the sharp decrease of the impact strength and elongation at break, which is reflected in the morphologies of the blend system obtained via scanning electron microscopy. In addition, the incorporation of α‐MSAN increased the tensile strength, flexural strength, and modulus. There were no new groups observed from Fourier‐transform infrared spectra, which means no strong specific intermolecular interactions existed between ASA and α‐MSAN. Moreover, the processibility of the blend system was obviously improved from the results of melt flow rate. J. VINYL ADDIT. TECHNOL., 22:156–162, 2016. © 2014 Society of Plastics Engineers     

Thermal properties and adhesion strength of amorphous poly(α‐olefins)/styrene–ethylene–butylene copolymer/terpene hot‐melt adhesive

The thermal stability and adhesion properties, such as lap‐shear strength of hot‐melt adhesives were obtained from amorphous poly(α‐olefins) and thermoplastic rubber [styrene–ethylene–butylene copolymer (SEBS)] blends. The addition of SEBS increased the toughness and viscosity and decreased the lap‐shear strength of the hot‐melt adhesive. Terpene tackifier resin offered enhanced lap‐shear strength; this was more effective when combined tackifier resin was added on the hot‐melt adhesive. Only a small amount of wax and antioxidant affected the thermal stability and lap‐shear strength of the hot‐melt adhesive. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

苯乙烯在MBS中的结合方式对PVC/MBS性能的影响

以乳液聚合法合成了化学组成恒定的具有核-壳结构的(甲基丙烯酸甲酯/丁二烯/苯乙烯)共聚物(MBS),通过改变原料及其配比,使苯乙烯(St)在MBS中以共聚或接枝方式结合,用动态力学热分析仪研究了MBS内耗与温度的关系。将MBS与聚氯乙烯(PVC)共混,研究了St结合方式对共混物冲击韧性及增韧机理的影响,结果表明,随着MBS核中St含量的增加,PVC/MBS共混物的脆-韧转变向高温移动;当St仅以接枝的方式结合时,橡胶粒子的空洞化及剪切屈服是主要的增韧机理,当St仅以共聚方式结合时,剪切屈服是主要的增韧机理。     

Improvement in the heat resistance of poly(vinyl chloride) profile with styrenic polymers

The styrenic polymers poly(α‐methylstyrene‐acrylonitrile) (α‐MSAN) and poly(acrylonitrile‐butadiene‐styrene) (ABS) and (three types) were used to improve the heat resistance of poly(vinyl chloride) (PVC). The glass transition temperature (T_g) and miscibility were analyzed by dynamic mechanical thermal analysis (DMTA). Effects of composition on heat distortion temperature (HDT) were investigated with the different styrenic polymers. Other physical properties such as mechanical properties and melt flow rate (MFR) were also determined. Morphology was observed by scanning electron microscopy (SEM) in order to support the mechanical property results. The PVC was miscible with α‐MSAN but partially miscible with the ABS series, and α‐MSAN was much more effective in enhancing the T_g and HDT of rigid PVC than the ABS series as for mechanical properties, the addition of α‐MSAN could improve the tensile strength, bending strength, and bending modulus but decrease the impact strength of the materials compared with the addition of the ABS series. Improvement in processability was observed in the MFR results with the addition of the styrenic polymers. On the basis of all the properties, the formulation with an α‐MSAN content of 30 phr (parts per hundred parts of resin) was superior for heat‐resistant PVC profile. The HDT of PVC could be increased from 76.9°C to 85.4°C (measured under the maximum bending stress of 0.45 MPa) and combined with good mechanical properties and processability by the addition of 30 phr of α‐MSAN. Also, a heat‐resistant PVC profile was successfully fabricated. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers     

Mechanical properties and deformation behaviors of acrylonitrile‐butadiene‐styrene under Izod impact test and uniaxial tension at various strain rates

Two polybutadiene‐graft‐acrylonitrile‐styrene copolymer (PBD‐g‐SAN) impact modifiers with different rubber particle size were synthesized by seeded emulsion polymerization. Acrylonitrile‐butadiene‐styrene (ABS) blends with a constant rubber concentration of 15 wt% were prepared by blending those impact modifiers and SAN resin. The major focus was the mechanical properties and deformation mechanisms of ABS blends under Izod impact test and uniaxial tension at various strain rates from 2.564 × 10^?4 S^?1 upto 1.282 × 10^?1 S^?1. By the combination of transmission electron microscope and scanning electron microscope, it was concluded that crazes and cavitation coexisted in ABS blends. The deformation mechanisms of ABS blend containing large rubber particles was rubber particles cavitation and shear yielding in the matrix including crazes, and they do not change with the strain rate. Different from ABS blend with large rubber particles, deformation mechanism of ABS with small rubber particles under tensile condition was only involved in shear yielding in the matrix and no crazes were formed. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Influence of the tert‐dodecyl mercaptan content in poly(acrylonitrile‐butadiene‐styrene) on properties of chlorinated polyvinyl chloride/poly(acrylonitrile‐butadiene‐styrene) blends

A series of poly(acrylonitrile‐butadiene‐styrene) (ABS) grafting modifiers were synthesized by emulsion grafting poly(acrylonitrile‐styrene) (SAN) copolymer onto polybutadiene (PB) latex rubber particles. The chain transfer reagent tert‐dodecyl mercaptan (TDDM) was used to regulate the grafting degree of ABS and the molecular weight of SAN copolymers. By blending these ABS modifiers with Chlorinated polyvinyl chloride (CPVC) resin, a series of CPVC/ABS blends were obtained. The morphology, compatibility, and the mechanical properties of CPVC/ABS blends were investigated. The scanning electron microscope (SEM) studies showed that the ABS domain all uniformly dispersed in CPVC matrix. Dynamic mechanical analyses (DMA) results showed that the compatibility between CPVC and SAN became enhanced with the TDDM content. From the mechanical properties study of the CPVC/ABS blends, it was revealed that the impact strength first increases and then decreases with the TDDM content, which means that the compatibility between CPVC and the SAN was not the only requirement for maximizing toughness. The decreasing of tensile strength and the elongations might attribute to the lower entanglement between chains of CPVC and SAN. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 toughened by maleated polystyrene‐based copolymers: Mechanical properties,morphology, and rheology

Poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 (PPO/PA6 30/70) blends were impact modified by addition of three kinds of maleated polystyrene‐based copolymers, i.e., maleated styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), maleated methyl methacrylate‐butadiene‐styrene copolymer (MBS‐g‐MA), and maleated acrylonitrile‐butadiene‐styrene copolymer (ABS‐g‐MA). The mechanical properties, morphology and rheological behavior of the impact modified PPO/PA6 blends were investigated. The selective location of the maleated copolymers in one phase or at interface accounted for the different toughening effects of the maleated copolymer, which is closely related to their molecular structure and composition. SEBS‐g‐MA was uniformly dispersed in PPO phase and greatly toughened PPO/PA6 blends even at low temperature. MBS‐g‐MA particles were mainly dispersed in the PA6 phase and around the PPO phase, resulting in a significant enhancement of the notched Izod impact strength of PPO/PA6 blends from 45 J/m to 281 J/m at the MBS‐g‐MA content of 20 phr. In comparison, the ABS‐g‐MA was mainly dispersed in PA6 phase without much influencing the original mechanical properties of the PPO/PA6 blend. The different molecule structure and selective location of the maleated copolymers in the blends were reflected by the change of rheological behavior as well. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effects of the polybutadiene/poly(styrene‐co‐acrylonitrile) ratio in a polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) impact modifier on the morphology and mechanical behavior of acrylonitrile–butadiene–styrene blends

Polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) (PB‐g‐SAN) impact modifiers with different polybutadiene (PB)/poly(styrene‐co‐acrylonitrile) (SAN) ratios ranging from 20.5/79.5 to 82.7/17.3 were synthesized by seeded emulsion polymerization. Acrylonitrile–butadiene–styrene (ABS) blends with a constant rubber concentration of 15 wt % were prepared by the blending of these PB‐g‐SAN copolymers and SAN resin. The influence of the PB/SAN ratio in the PB‐g‐SAN impact modifier on the mechanical behavior and phase morphology of ABS blends was investigated. The mechanical tests showed that the impact strength and yield strength of the ABS blends had their maximum values as the PB/SAN ratio in the PB‐g‐SAN copolymer increased. A dynamic mechanical analysis of the ABS blends showed that the glass‐transition temperature of the rubbery phase shifted to a lower temperature, the maximum loss peak height of the rubbery phase increased and then decreased, and the storage modulus of the ABS blends increased with an increase in the PB/SAN ratio in the PB‐g‐SAN impact modifier. The morphological results of the ABS blends showed that the dispersion of rubber particle in the matrix and its internal structure were influenced by the PB/SAN ratio in the PB‐g‐SAN impact modifiers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2165–2171, 2005     

The toughness and morphology of (chlorinated poly[vinyl chloride])/(methyl methacrylate‐butadiene‐styrene) blends

A series of methyl methacrylate‐butadiene‐styrene (MBS) graft copolymers were synthesized via seeded emulsion polymerization techniques by grafting styrene and methyl methacrylate on poly(butadiene‐co‐styrene) (SBR) particles. The chlorinated poly(vinyl chloride) (CPVC)/MBS blends were obtained by melting MBS graft copolymers with CPVC resin, and the effect of the core/shell ratio of MBS graft copolymer and SBR content of CPVC/MBS blends on the mechanical properties and morphology of CPVC/MBS blends was studied. The results showed that, with the increase in the core/shell ratio, the impact strength of the blend increased and then decreased. It was found that, when the core/shell ratio was 50/50, the impact strength was about 155 J/m, and the tensile strength evidently increased. The toughness of the CPVC/MBS blend was closely related to the SBR content of the blend, and with the increasing of SBR content of blend, the impact strength of the blend increased. The morphology of CPVC/MBS blends was observed via scanning electron microscopy. Scanning electron microscopy indicated that the toughness of CPVC/MBS blend was consistence with the dispersion of MBS graft copolymers in the CPVC matrix. J. VINYL ADDIT. TECHNOL., 22:501–505, 2016. © 2015 Society of Plastics Engineers     

Impact behavior and fracture morphology of acrylonitrile–butadiene–styrene resins toughened by linear random styrene–isoprene–butadiene rubber

A novel toughening modifier, styrene–isoprene–butadiene rubber (SIBR), was used to improve the impact resistance and toughness of acrylonitrile–butadiene–styrene (ABS) resin via bulk polymerization. For comparison, two kinds of ABS samples were prepared: ABS‐1 was toughened by a conventional modifier (a low‐cis polybutadiene rubber/styrene–butadiene block copolymer), and ABS‐2 was toughened by SIBR. The mechanical properties, microstructures of the as‐prepared materials, and fracture surface morphology of the specimens after impact were studied by instrumented notched Izod impact tests and tensile tests, transmission electron microscopy, and scanning electron microscopy, respectively. The mechanical test results show that ABS‐2 had a much higher impact strength and elongation at break than ABS‐1. The microscopic results suggested that fracture resistance of ABS‐1 only depended on voids, shear yielding, and few crazing, which resulted in less ductile fracture behavior. Compared with ABS‐1, ABS toughened by linear random SIBR (ABS‐2) displayed the synergistic toughening effect of crazing and shear yielding, which could absorb and dissipate massive energy, and presented high ductile fracture behavior. These results were also confirmed by instrumented impact tests. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Large stabilizing effect of titanium dioxide on photodegradation of PVC/α‐methylstyrene‐acrylonitrile copolymer/impact modifier‐matrix composites

A large stabilizing effect was obtained via adding titanium dioxide (TiO₂) into poly (vinyl chloride)/α‐methylstyrene‐acrylonitrile copolymer/impact modifier blends. A comparison between photodegradation of blends (without TiO₂) and composites (with TiO₂) was conducted. Results of color difference, surface morphology, and thermogravimetric analysis tests indicated the higher UV resistance of composites than blends. Composites exhibited a almost unchangeable tensile strength and a certain retention rate of elongation at break; while drastic loss in these two properties were observed for blends. Fourier transform infrared and rheological tests also revealed the stabilizing effect exerted by TiO₂, and it was found that different systems exhibited different stabilizing mechanisms. POLYM. COMPOS., 35:2365–2375, 2014. © 2014 Society of Plastics Engineers     

Acrylonitrile-styrene-acrylate particles with different acrylonitrile contents for improving the toughness of poly(vinyl chloride) resin

Poly(butyl acrylate) grafted styrene and acrylonitrile copolymer (PBA-g-SAN, ASA) with core–shell structures were prepared by emulsion polymerization technology to improve the toughness of the poly(vinyl chloride) (PVC). The mechanical properties of the PVC/ASA blends were investigated. The notch impact strength of the PVC/ASA blend could reach 1200 J/m when the 13 phr ASA was added to the PVC. This was several times more than pure PVC resin. Scanning electron microscopy analysis results indicated that the improvement in impact strength of the PVC/ASA blend was attributed to shear yielding induced by ASA particles. Additionally, subtle changes in the ratio of monomers in the shell layer led to significant fluctuations in the mechanical properties of the composites. Dynamic mechanical analysis showed that the intermolecular interaction forces between ASA particles and PVC resins played a key role in improving the toughness of PVC/ASA blend.     

Influence of epoxy resin on the properties of maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer toughened polyamide 6 blends

Maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer (ABS‐g‐MA) was used as an impact modifier of polyamide 6 (PA6). Epoxy resin was introduced into PA6/ABS‐g‐MA blends to further improve their properties. Notched Izod impact tests showed that the impact strength of PA6/ABS‐g‐MA could be improved from 253 to 800 J/m with the addition of epoxy resin when the ABS‐g‐MA content was set at 25 wt %. Differential scanning calorimetry results showed that the addition of epoxy resin made the crystallization temperature and melting temperature shift to lower temperatures; this indicated the decrease in the PA6 crystallization ability. Dynamic mechanical analysis testing showed that the addition of epoxy resin induced the glass‐transition temperature of PA6 and the styrene‐co‐acrylonitrile copolymer phase to shift to higher temperatures due to the chemical reactions between PA6, ABS‐g‐MA, and epoxy resin. The scanning electron microscopy results indicated that the ABS‐g‐MA copolymer dispersed into the PA6 matrix uniformly and that the phase morphology of the PA6/ABS‐g‐MA blends did not change with the addition of the epoxy resin. Transmission electron microscopy showed that the epoxy resin did not change the deformation mechanisms of the PA6/ABS‐g‐MA blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Blends of bisphenol A polycarbonate and rubber‐toughened styrene–maleic anhydride copolymers

The morphology and mechanical properties of polycarbonate (PC) blends with rubber‐toughened styrene–maleic anhydride copolymer materials (TSMA) were investigated and compared with the properties of blends of PC with acrylonitrile–butadiene–styrene (ABS) materials. The PC/TSMA blends showed similar composition dependence of properties as the comparable PC/ABS blends. Polycarbonate blends with TSMA exhibited higher notched Izod impact toughness than pure PC under sharp‐notched conditions but the improvements are somewhat less than observed for similar blends with ABS. Since PC is known for its impact toughness except under sharp‐notched conditions, this represents a significant advantage of the rubber‐modified blends. PC blends with styrene–maleic anhydride copolymer (SMA) were compared to those with a styrene–acrylonitrile copolymer (SAN). The trends in blend morphology and mechanical properties were found to be qualitatively similar for the two types of copolymers. PC/SMA blends are nearly transparent or slightly pearlescent. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1508–1515, 1999     

Influence of acrylonitrile–butadiene–styrene (ABS) morphology and poly(styrene‐co‐acrylonitrile) (SAN) content on fracture behavior of ABS/SAN blends

This study attempted to correlate morphological changes and physical properties for a high rubber content acrylonitrile–butadiene–styrene (ABS) and its diluted blends with a poly(styrene‐co‐acrylonitrile) (SAN) copolymer. The results showed a close relationship between rubber content and fracture toughness for the blends. The change of morphology in ABS/SAN blends explains in part some deviations in fracture behavior observed in ductile–brittle transition temperature shifts. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2606–2611, 2004     

Two‐component acrylic structural adhesive initiated by tributylborane for untreated PET adhesion

In order to improve the adhesion strength of acrylic adhesive to untreated poly(ethylene terephthalate) (PET) substrate, two‐component acrylic structural adhesives initiated by tributylborane were prepared. The effects of acrylic monomers, elastomers, decomplexers, and oligomers on the adhesion properties of two‐component acrylic structural adhesive were investigated in sequence. It is found that the shear strength on PET of adhesives toughened by acrylonitrile–butadiene–styrene copolymer and carboxyl‐terminated butadiene–acrylonitrile copolymer is higher than that of commercial adhesives Dp8010NS and Loctite 3030. A tailored oligomer was synthesized from hydroxyl propyl–terminated polydimethylsiloxane and 3‐isopropenyl‐α,α‐dimethylbenzyl isocyanate. It is also noticed that premature failure usually takes place in the lap shear test samples due to the brittleness of the acrylic adhesive, except in the sample of adhesive modified by tailored oligomer. Excellent adhesion to the PET substrate is achieved by this adhesive modified by tailored oligomer, with a lap shear strength above 11 MPa and T‐peel strength up to 5.34 N/mm. Additionally, the resulting adhesive is qualified for the structural bonding of PET materials. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46612.