Study on in situ reinforcing and toughening of a semiflexible thermotropic copolyesteramide in PBT/PA66 blends

Ternary in situ composites based on poly(butylene terephthalate) (PBT), polyamide 66 (PA66), and semixflexible liquid crystalline polymer (LCP) were systematically investigated. The LCP used was an ABA30/PET liquid crystalline copolyesteramide based on 30 mol % of p‐aminobenzoic acid (ABA) and 70 mol % of poly(ethylene terephthalate) (PET). The specimens for thermal and rheological measurements were prepared by batch mixing, while samples for mechanical tests were prepared by injection molding. The results showed that the melting temperatures of the PBT and PA66 phases tend to decrease with increasing LCP addition. They also shifted toward each other due to the compatibilization of the LCP. The torque measurements showed that the ternary blends exhibited an apparent maximum near 2.5–5 wt % LCP. Thereafter, the viscosity of the blends decreased dramatically at higher LCP concentrations. Furthermore, the torque curves versus the PA66 composition showed that the binary PBT/PA66 blends can be classified as negative deviation blends (NDBs). The PBT/PA66/LCP blends containing up to 15 wt % LCP were termed as positive deviation blends (PDBs), while the blends with the LCP ≥25 wt % exhibited an NDB behavior. Finally, the tensile tests showed that the stiffness and tensile strength of ternary in situ composites were generally improved with increasing LCP content. The impact strength of ternary composites initially increased by the LCP addition, then deteriorated when the LCP content was higher than 10 wt %. The correlation between the mechanical properties and morphology of the blends is discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1975–1988, 2000     

Crystallization kinetics of poly(ethylene terephthalate) with thermotropic liquid crystalline polymer blends

The isothermal and dynamic crystallization behaviors of polyethylene terephthalate (PET) blended with three types of liquid crystal polymers, i.e., PHB60–PET40, HBA73–HNA27, [(PHB60–PET40)–(HBA73–HNA27) 50 : 50], have been studied using differential scanning calorimetry (DSC). The kinetics were calculated using the slope of the crystallization versus time plot, the time for 50% reduced crystallinity, the time to attain maximum rate of crystallization, and the Avrami equation. All the liquid crystalline polymer reinforcements with 10 wt % added accelerated the rate of crystallization of PET; however, the order of the acceleration effect among the liquid crystalline polymers could not be defined from the isothermal crystallization kinetics. The order of the effect for liquid crystalline polymer on the crystallization of PET is as follows: (PHB60–PET40)–(HBA73–HNA27) (50 : 50); HBA73–HNA27; PHB60–PET40: This order forms the dynamic scan of the DSC measurements. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:1383–1392, 1998     

Morphological and mechanical properties of PET-LCP blend fibers

Blends of poly(ethylene terephthalate-co-p-oxybenzoate) (PET–PHB) with poly(ethylene terephthalate) (PET) have been studied in the form of as-spun and drawn fibers. Mechanical properties of drawn blend fibers (DR-6.0) up to 10 wt % liquid crystalline polymer (LCP) component exhibit significant improvement in modulus and strength. With the addition of 10 wt % LCP content in PET matrix, the modulus increases from 11.78 to 17.72 GPa, and the strength increases from 0.76 to 1.0 GPa in comparison to the PET homopolymer. With further addition of LCP content, the properties drop down. Scanning electron microscopy studies of drawn blend fibers show that up to 10 wt % LCP content the blends contain the LCP domains in the size range of 0.07–0.2 μm and are well distributed in the PET matrix. © 1995 John Wiley & Sons, Inc.     

Biodegradable polymer blends of poly(3-hydroxybutyrate) and poly(DL-lactide)-co-poly(ethylene glycol)

The melting and crystallization behavior and phase morphology of poly(3-hydroxybutyrate) (PHB) and poly(DL-lactide)-co-poly(ethylene glycol) (PELA) blends were studied by DSC, SEM, and polarizing optical microscopy. The melting temperatures of PHB in the blends showed a slight shift, and the melting enthalpy of the blends decreased linearly with the increase of PELA content. The glass transition temperatures of PHB/PELA (60/40), (40/60), and (20/80) blends were found at about 30°C, close to that of the pure PELA component, during DSC heating runs for the original samples and samples after cooling from the melt at a rate of 20°C/min. After a DSC cooling run at a rate of 100°C/min, the blends showed glass transitions in the range of 10–30°C. Uniform distribution of two phases in the blends was observed by SEM. The crystallization of PHB in the blends from both the melt and the glassy state was affected by the PELA component. When crystallized from the melt during the DSC nonisothermal crystallization run at a rate of 20°C/min, the temperatures of crystallization decreased with the increase of PELA content. Compared with pure PHB, the cold crystallization peaks of PHB in the blends shifted to higher temperatures. Well-defined spherulites of PHB were found in both pure PHB and the blends with PHB content of 80 or 60%. The growth of spherulites of PHB in the blends was affected significantly by 60% PELA content. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 1849–1856, 1997     

Phase structure and viscoelastic properties of compatibilized blends of PET and HDPE recyclates

Immiscible blends of recycled poly(ethylene terephthalate) (R‐PET), containing some amount of polymeric impurities, and high‐density polyethylene (R‐PE), containing admixture of other polyolefins, in weight compositions of 75 : 25 and 25 : 75 were compatibilized with selected compatibilizers: maleated styrene–ethylene/butylene–styrene block copolymer (SEBS‐g‐MA) and ethylene–glycidyl methacrylate copolymer (EGMA). The efficiency of compatibilization was investigated as a function of the compatibilizer content. The rheological properties, phase structure, thermal, and viscoelastic behavior for compatibilized and binary blends were studied. The results are discussed in terms of phase morphology and interfacial adhesion among components. It was shown that the addition of the compatibilizer to R‐PET‐rich blends and R‐PE‐rich blends increases the melt viscosity of these systems above the level characteristic for the respective binary blends. The dispersion of the minor phase improved with increasing compatibilizer content, and the largest effects were observed for blends compatibilized with EGMA. Calorimetric studies indicated that the presence of a compatibilizer had a slight affect on the crystallization behavior of the blends. The dynamic mechanical analysis provided evidence that the occurrence of interactions of the compatibilizer with blend components occurs through temperature shift and intensity change of a β‐relaxation process of the PET component. An analysis of the loss spectra behavior suggests that the optimal concentration of the compatibilizers in the considered blends is close to 5 wt %. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1423–1436, 2001     

Microstructure and crystallization of melt‐mixed poly(ethylene terephthalate)/poly(ethylene isophthalate) blends

Physical blends of poly(ethylene terephthalate) (PET) and poly(ethylene isophthalate) (PEI), abbreviated PET/PEI (80/20) blends, and of PET and a random poly(ethylene terephthalate‐co‐isophthalate) copolymer containing 40% ethylene isophthalate (PET₆₀I₄₀), abbreviated PET/PET₆₀I₄₀ (50/50) blends, were melt‐mixed at 270°C for different reactive blending times to give a series of copolymers containing 20 mol % of ethylene isophthalic units with different degrees of randomness. ¹³C‐NMR spectroscopy precisely determined the microstructure of the blends. The thermal and mechanical properties of the blends were evaluated by DSC and tensile assays, and the obtained results were compared with those obtained for PET and a statistically random PETI copolymer with the same composition. The microstructure of the blends gradually changed from a physical blend into a block copolymer, and finally into a random copolymer with the advance of transreaction time. The melting temperature and enthalpy of the blends decreased with the progress of melt‐mixing. Isothermal crystallization studies carried out on molten samples revealed the same trend for the crystallization rate. The effect of reaction time on crystallizability was more pronounced in the case of the PET/PET₆₀I₄₀ (50/50) blends. The Young's modulus of the melt‐mixed blends was comparable to that of PET, whereas the maximum tensile stress decreased with respect to that of PET. All blend samples showed a noticeable brittleness. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3076–3086, 2003     

Improvement of compatibility of poly(ethylene terephthalate) and poly(ethylene octene) blends by γ‐irradiation

Blends of poly(ethylene terephthalate) (PET) and poly(ethylene octene) (POE) were prepared by melt blending with various amounts of trimethylolpropane triacylate (TMPTA). The mechanical properties, phase morphologies, and gel fractions at various absorbed doses of γ‐irradiation have been investigated. It was found that the toughness of blends was enhanced effectively after irradiation as well as the tensile properties. The elongation at break for all studied PET/POE blends (POE being up to 15 wt %) with 2 wt % TMPTA reached 250–400% at most absorbed doses of γ‐irradiation, approximately 50–80 times of those of untreated PET/POE blends. The impact strength of PET/POE (85/15 wt/wt) blends with 2 wt % TMPTA irradiated with as little as 30 kGy absorbed dose exceeded 17 kJ/m², being approximately 3.4 times of those of untreated blends. The improvement of the mechanical properties was supported by the morphology changes. Scanning electron microscope images of fracture surfaces showed a smaller dispersed phase and more indistinct inter‐phase boundaries in the irradiated blends. This indicates increased compatibility of PET and POE in the PET/POE blends. The changes of the morphologies and the enhancement of the mechanical properties were ascribed to the enhanced inter‐phase boundaries by the formation of complex graft structures confirmed by the results of the gelation extraction and Fourier Transform Infrared analyses. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Rheological behavior of polyester blend and mechanical properties of the polypropylene–polyester blend fibers

The article deals with method of preparation, rheological properties, phase structure, and morphology of binary blend of poly(ethylene terephthalate) (PET)/poly(butylene terephthalate) (PBT) and ternary blends of polypropylene (PP)/(PET/PBT). The ternary blend of PET/PBT (PES) containing 30 wt % of PP is used as a final polymer additive (FPA) for blending with PP and subsequent spinning. In addition commercial montane (polyester) wax Licowax E (LiE) was used as a compatibilizer for spinning process enhancement. The PP/PES blend fibers containing 8 wt % of polyester as dispersed phase were prepared in a two‐step procedure: preparation of FPA using laboratory twin‐screw extruder and spinning of the PP/PES blend fibers after blending PP and FPA, using a laboratory spinning equipment. DSC analysis was used for investigation of the phase structure of the PES components and selected blends. Finally, the mechanical properties of the blend fibers were analyzed. It has been found that viscosity of the PET/PBT blends is strongly influenced by the presence of the major component. In addition, the major component suppresses crystallinity of the minor component phase up to a concentration of 30 wt %. PBT as major component in dispersed PES phase increases viscosity of the PET/PBT blend melts and increases the tensile strength of the PP/PES blend fibers. The impact of the compatibilizer on the uniformity of phase dispersion of PP/PES blend fibers was demonstrated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4222–4227, 2006     

Melting,crystallization behaviors,and nonisothermal crystallization kinetics of PET/PTT/PBT ternary blends

The melting, crystallization behaviors, and nonisothermal crystallization kinetics of the ternary blends composed of poly(ethylene terephthalate), poly(trimethylene terephthalate) (PTT) and poly(buthylene terephthalate) (PBT) were studied with differential scanning calorimeter (DSC). PBT content in all ternary blends was settled invariably to be one‐third, which improved the melt‐crystallization temperature of the ternary blends. All of the blend compositions in amorphous state were miscible as evidenced by a single, composition‐dependent glass transition temperature (T_g) observed in DSC curves. DSC melting thermograms of different blends showed different multiple melting and crystallization peaks because of their various polymer contents. During melt‐crystallization process, three components in blends crystallized simultaneously to form mixed crystals or separated crystals depending upon their content ratio. The Avrami equation modified by Jeziorny and the Ozawa theory were employed to describe the nonisothermal crystallization process of two selected ternary blends. The results spoke that the Avrami equation was successful in describing the nonisothermal crystallization process of the ternary blends. The values of the t_1/2 and the parameters Z_c showed that the crystallization rate of the ternary blends with more poly(ethylene terephthalate) content was faster than that with the lesser one at a given cooling rate. The crystal morphology of the five ternary blends investigated by polarized optical microscopy (POM) showed different size and distortional Maltese crosses or light spots when the PTT or poly(ethylene terephthalate) component varied, suggesting that the more the PTT content, the larger crystallites formed in ternary blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

PET/PEA共混物的非等温结晶及晶态结构

采用升、降温DSC和广角X射线衍射等测试手段研究了不同共混比的PET/液晶共聚酯酰胺(PEA)机械共混物、溶液共混物的非等混结晶和晶态结构。结果表明PEA在20％的范围内能起到成核剂的作用,促进PET结晶,并且当PEA的加入量为2.5％时,PET最易结晶;共混物中PET的晶态结构受PEA的影响不大,PEA的引入使共混物各晶面间距增大,共混物的结晶度呈现先上升而后降低之趋势。     

Lamellar Morphology of Poly(3-hydroxybutyrate)/Poly(ethylene oxide) Blends as Studied via Small Angle X-ray Scattering

The lamellar morphology of a melt-miscible blend consisting of two crystalline constituents, poly(3-hydroxybutyrate) (PHB) and poly(ethylene oxide) (PEO) have been investigated by means of small angle X-ray scattering (SAXS). The blend was a crystalline/amorphous system when temperatures lay between the melting point of PEO (ca. T _m ^PEO=60C) and that of PHB (ca. T _m ^PHB=170C), while it became a crystalline/crystalline system below T _m ^PEO. The crystalline microstructures of the blends were induced by two types of crystallization history, i.e. one-step and two-step crystallizations. In the one-step crystallization, the blends were directly quenched from the melt to room temperature to allow simultaneous PHB and PEO crystallization. The two-step crystallization involved first cooling to 70C to allow PHB crystallization for 72 h followed by cooling to room temperature (ca. 19C) to allow PEO crystallization. In the crystalline/crystalline state, two scattering peaks have been observed in the Lorentz-corrected SAXS profiles, irrespective of the crystallization histories, meaning that crystallization created separate PHB and PEO lamellar stack domains. One-step crystallization yielded lamellar stack domains containing almost pure PHB and PEO lamellae. Two-step crystallization generated almost pure PHB lamellar domains and the PEO lamellar domains with inserted PHB lamellae. In the crystalline/amorphous state, the composition dependence of the amorphous layer thickness (l _a), the presence of zero-angle scattering, and the volume fraction of the PHB lamellar stack (_s) revealed that both one-step and two-step crystallizations, generated the interfibrillar segregation morphology, where the extent of interfibrillar segregation of amorphous PEO increased with increasing PEO content.     

Recycled poly(ethylene terephthalate)/linear low‐density polyethylene blends through physical processing

Poly(styrene‐ethylene/butylene‐styrene) (SEBS) was used as a compatibilizer to improve the thermal and mechanical properties of recycled poly(ethylene terephthalate)/linear low‐density polyethylene (R‐PET/LLDPE) blends. The blends compatibilized with 0–20 wt % SEBS were prepared by low‐temperature solid‐state extrusion. The effect of SEBS content was investigated using scanning electron microscope, differential scanning calorimeter, dynamic mechanical analysis (DMA), and mechanical property testing. Morphology observation showed that the addition of 10 wt % SEBS led to the deformation of dispersed phase from spherical to fibrous structure, and microfibrils were formed at the interface between two phases in the compatibilized blends. Both differential scanning calorimeter and DMA results revealed that the blend with 20 wt % SEBS showed better compatibility between PET and LLDPE than other blends studied. The addition of 20 wt % of SEBS obviously improved the crystallizibility of PET as well as the modulus of the blends. DMA analysis also showed that the interaction between SEBS and two other components enhanced at high temperature above 130°C. The impact strength of the blend with 20 wt % SEBS increased of 93.2% with respect to the blend without SEBS, accompanied by only a 28.7% tensile strength decrease. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Rheological and thermal properties of blends of modified poly(ethylene terephthalate) with p‐acetoxybenzoic acid and poly(butylene terephthalate)

Blending of thermotropic liquid crystalline polyesters (LCPs) with conventional polymers could result in materials that can be used as an alternative for short fiber‐reinforced thermoplastic composites, because of their low melt viscosity as well as their inherent high stiffness and strength, high use temperature, and excellent chemical resistance and low coefficient of expansion. In most of the blends was used LCP of 40 mol % of poly(ethylene terephthalate) (PET) and 60 mol % of p‐acetoxybenzoic acid (PABA). In this work, blends of several copolyesters having various PABA compositions from 10 to 70 mol % and poly(butylene terephthalate) (PBT) were prepared and their rheological and thermal properties were investigated. For convenience, the copolyesters were designated as PETA‐x, where x is the mol % of PABA. It was found that PET‐60 and PET‐70 copolyesters decreased the melt viscosity of PBT in the blends and those PBT/PETA‐60 and PBT/PETA‐70 blends showed different melt viscosity behaviors with the change in shear rate, while blends of PBT and PET‐x having less than 50 mol % of PABA exhibited totally different rheological behaviors. The blends of PBT with PETA‐50, PETA‐60, and PETA‐70 showed the morphology of multiple layers of fibers. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1797–1806, 1999     

Molecular orientation of extruded PET/LCP blend films. Part I: Polarized infrared spectroscopy

The polarized infrared (IR) spectroscopy technique was used to evaluate the surface uniaxial molecular orientation of films of poly(ethylene terephthalate) (PET), two thermotropic liquid crystalline polymers (LCPs), Vectra®A950 and Rodrun®LC5000, and their blends obtained by extrusion. The molecular orientation of the LCP and of the crystalline and amorphous PET phases in the draw direction was evaluated along the transverse section of the films and as a function of the blend composition. A compatibilizer agent was used to improve the interfacial adhesion between the PET and LCPs. The results showed that the surface molecular orientation of both LCPs was very high along the draw direction. However, when blended, the orientation of the LCP phase decreased drastically, it was dependent of its content and varied along the transverse section of the extruded films. The maximum orientation was observed in the blend with 5 wt % LCP content and at the position where the shear rate was maxima. The LCP Vectra®A950 showed higher orientation than the Rodrun®LC5000, as a pure material and as blended. For the PET phases, an alignment of the amorphous phase in the draw direction due to the presence of LCP and compatibilizer agent was observed. The crystalline phase of PET, however, showed no significant orientation in the draw direction. The compatibilizer agent proved efficient for both PET/LCP systems. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2241–2248, 2006     

Miscibility study on blend of thermotropic liquid crystalline polymers and polyester

The miscibility of thermotropic liquid crystalline polymers (TLCPs) and polyester blends was investigated with thermal and morphological analyses, as well as transesterification. TLCPs composed of 80 mol % para‐hydroxybenzoate (PHB) and 20 mol % poly(ethylene terephthalate) (PET) or 60 mol % PHB and 40 mol % PET, and polyesters such as PET and poly(ethylene 2,6‐naphthalate) (PEN) were melt blended in an internal mixer. DSC analyses were performed to investigate the thermal transition behavior and to obtain thermodynamic parameters. All the blends showed only a single glass‐transition temperature, which means they are partially miscible in the molten state. The Flory–Huggins interaction parameter was calculated employing the Nishi–Wang approach, and negative values were obtained except for the P(HB8‐ET2)/PEN blends. Transesterification was investigated using ¹H‐NMR, and the change of chemical shift compared to pure PET or P(HB‐ET)s was observed in the P(HB‐ET)/PET blends. An intermediate chemical shift value (4.83 ppm) was observed in the P(HB6‐ET4)/PEN blends, which indicates transesterification occurred. The fractured surface morphology of scanning electron micrographs showed that the interfaces between the LC droplets and matrix were not distinct. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1842–1851, 2003     

PET/PLA共混物相容性和结晶性能的研究

研究了相容剂钛酸四丁酯[Ti(OBu)4]含量、聚乳酸(PLA)含量对聚对苯二甲酸乙二醇酯(PET)/PLA共混物相容性的影响,探讨了共混物的熔融和结晶行为,并对其结晶形貌进行了观察。结果表明,Ti(OBu)4含量为PLA的4%(质量分数,下同)时,PET/PLA共混物的相容性良好,但当PLA含量超过30%时,共混物出现相分离;PLA的加入使PET的结晶峰变窄,结晶速率增加,且结晶峰温度向高温方向移动;PLA的加入使PET的晶粒尺寸大幅减小,晶粒数目大幅增加,结晶更加完善。     

端苯基超支化聚酯对PET结晶行为和构象的影响

采用差示扫描量热法(DSC)和衰减全反射傅里叶变换红外光谱(ATR-FTIR)研究了不同代数和含量的端苯基超支化聚酯(HBP)对聚对苯二甲酸乙二醇酯(PET)结晶行为和构象的影响,计算了晶带与内标峰的吸光度比值以及左右式构象的相对含量.其中975 cm?1和1340 cm?1处的吸收峰归属于反式构象,1370 cm?1处归属于左右式构象,793 cm?1和873 cm?1处的吸收峰为内标峰.结果表明,6%的第三代超支化聚酯对PET的结晶促进能力最强.随着超支化聚酯含量或代数的增加,各吸光度比值基本上都呈现出先增大后减小的趋势,左右式构象的含量则表现出先减小后增大的趋势.端苯基超支化聚酯既可以充当成核剂,又可以充当结晶促进剂,因而可以促进PET结晶.     

A comparative study of structure–property relationships in highly oriented thermoplastic and thermotropic polyesters with different chemical structures

Structure and properties of commercially available fully oriented thermoplastic and thermotropic polyester fibers have been investigated using optical birefringence, infrared spectroscopy, wide‐angle X‐ray diffraction and tensile testing methods. The effect of the replacement of p‐phenylene ring in poly(ethylene terephthalate) (PET) with stiffer and bulkier naphthalene ring in Poly(ethylene 2,6‐naphthalate) (PEN) structure to result in an enhanced birefringence and tensile modulus values is shown. There exists a similar case with the replacement of linear flexible ethylene units in PET and PEN fibers with fully aromatic rigid rings in thermotropic polyesters. Infrared spectroscopy is used in the determination of crystallinity values through the estimation of trans conformer contents in the crystalline phase. The analysis of results obtained from infrared spectroscopy data of highly oriented PET and PEN fibers suggests that trans conformers in the crystalline phase are more highly oriented than gauche conformers in the amorphous phase. Analysis of X‐ray diffraction traces and infrared spectra shows the presence of polymorphic structure consisting of α‐ and β‐phase structures in the fully oriented PEN fiber. The results suggest that the trans conformers in the β‐phase is more highly oriented than the α‐phase. X‐ray analysis of Vectran® MK fiber suggests a lateral organization arising from high temperature modification of poly(p‐oxybenzoate) structure, whereas the structure of Vectran® HS fiber contains regions adopting lateral chain packing similar to the room temperature modification of poly(p‐oxybenzoate). Both fibers are shown by X‐ray diffraction and infrared analyses to consist of predominantly oriented noncrystalline (63–64%) structure together with smaller proportion of oriented crystalline (22–24%) and unoriented noncrystalline (12–15%) structures. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 142–160, 2006     

Melting and crystallization behavior of poly(ethylene terephthalate) and poly(m‐xylylene adipamide) blends

The crystallization and melting behaviors as well as the crystalline morphologies of Poly(ethylene terephthalate)/Poly(m‐xylylene adipamide) (PET/MXD6) blends have been examined and characterized with the aid of differential scanning calorimetry (DSC) and wide angle x‐ray diffraction (WAXD). The isothermal and nonisothermal crystallization behaviors of the blends were studied as functions of the contents of MXD6, catalyst concentrations, and the effects of the interchange reactions between PET and MXD6. Wide angle x‐ray scattering has been used to examine the crystalline morphologies of the PET/MXD6 blends, to characterize their crystalline and amorphous phases, and to determine crystallite sizes in the blends. Results indicate that the catalyst has both catalyzing and nucleation effects on the PET/MXD6 blends, with the extents of each effect dependent upon the content of catalyst. In addition the crystalline morphology was found to be dominated by the MXD6 content as well as the crystallization temperature. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Dielectric Properties of Thermotropic Polymer Liquid Crystals

Abstract

Dielectric relaxation spectrometry is a useful tool to study molecular dynamics of macromolecular systems. Theoretical principles as well as experimental techniques are analyzed from the point of view of their capabilities. Results are reported for PET/xPHB, where PET = poly(ethylene terephthalate), PHB = p-bydroxybenzoic acid (the liquid crystalline component) and x is the mole fraction of PHB in the copolymers.