Synthesis and mechanical properties of lightweight hybrid geopolymer foams reinforced with carbon nanotubes

A lightweight hybrid geopolymer foams reinforced with carbon nanotubes (CNTs) was exploited by adding the CNTs into geopolymeric matrix through hydrogen peroxide method. The synergistic effects of nanotubes and foaming agent on the phase evolution, microstructure, and mechanical properties were investigated. After introduction of nanotubes, the geopolymer foams reinforced with CNTs (CNTs/KGP) still showed amorphous structure. Porosity of the foams increased with the H₂O₂ content and decreased with the increase in CNTs content. The addition of CNTs (1-9 wt%) in foams refined the distribution of pore size from 523 to 352 μm. Compression strength of the CNTs/KGP samples elevated with the increasing content of CNTs, which was contributed to the crack propagation and bridging of CNTs in foams. The CNTs/KGP foams with considerable porosity show potential applications in adsorption, filtration, membrane supports, other industries, etc     

Formation of SiC whiskers/leucite-based ceramic composites from low temperature hardening geopolymer

In this study, SiC whiskers (SCWS) reinforced geopolymer composites (SCWS/KGP) and their ceramic products (SCWS/leucite) were prepared, and effects of SiC whiskers contents on the microstructure and flexural strength of the SCWS/KGP and SCWS/leucite composites were investigated. The results show that the whisker addition has little influence on both phase composition and thermal shrinkage of the KGP composites, but a suitable content of whisker will result in the improved flexural strength, and when the SCWS content is 2 wt%, flexural strength of the SCWS/KGP composite is enhanced by 95% compared with the neat geopolymer. The flexural strength of the composites can be further enhanced significantly after the composites being treated at 1100 °C and 1200 °C and flexural strength of the composite with SCWS content of 2 wt% was 107% and 125% higher than the untreated counterpart, respectively. The increase in flexural strength of the composites should be attributed to the strong leucite formation, whisker debonding and pulling out from matrix during the fracturing process based on the good interfacial bonding state between whisker and leucite matrix.     

Effects of high-temperature exposure on properties of lightweight geopolymer foams incorporating diatomite powders

A kind of metakaolin-based geopolymer foams incorporating diatomite powders (GKGP) with open cellular was presented by addition of diatomite powder via hydrogen peroxide method. Impacts of high-temperature exposure on the microstructure, pore structure, and mechanical properties of the GKGP samples were investigated. The GKGP foams achieved a typical amorphous phase structure at room temperature. Open porosity of the samples reached approximately 74%. After high-temperature exposure treatment, the KGP matrix is basically transformed into leucite crystal phase. The compression strength of the leucite foams was also enhanced with increasing temperature to 1200℃ (9.28 MPa). The lightweight foamed GKGP samples with high open porosity might have great potential for membranes and industries, etc.     

Microstructure and mechanical properties of cold sintered porous alumina ceramics

New innovative approach to fabricate porous alumina ceramics by cold sintering process (CSP) is presented using NaCl as pore forming agent. The effects of CSP and post-annealing temperature on the microstructure and mechanical strength were investigated. Al₂O₃–NaCl composite with bulk density of 2.92 g/cm³ was compacted firstly using CSP and then a porous structure was formed using post-annealing at 1200°C–1500°C for 30 min. Brazilian test method and Vickers hardness test were used to determine the indirect tensile strength and hardness of the porous alumina, respectively. Meanwhile, the phases and the microstructure were respectively examined using X-ray diffractometer and scanning electron microscope (SEM) complemented by the 3D image analysis with X-ray tomography (XRT). SEM structural and XRT image analysis of cold sintered composite showed a dense structure with NaCl precipitated between Al₂O₃ particles. The NaCl volatization from the composite was observed during the annealing and then complete porous Al₂O₃ structure was formed. The porosity decreased from 48 vol% to 28 vol% with the annealing temperature increased from 1200 °C to 1500 °C, while hardness and mechanical strength increased from 14.3 to 115.4 HV and 18.29–132.82 MPa respectively. The BET analysis also showed a complex pore structure of micropores, mesopores and macropores with broad pore size distribution.     

Fabrication and characterization of alumina and zirconia-toughened alumina porous structures

In the present study, alumina (Al₂O₃) and zirconia-toughened alumina (ZTA) porous structures (foams) were manufactured using the space holder technique. Al₂O₃ and ZTA foams with varying porosities from 20% to 69% were fabricated by adding different sizes (10, 20, and 40 μm) and different volume % of polystyrene beads (space holders) to Al₂O₃ and ZTA powders. All the fabricated foams were investigated under static conditions to assess the compressive behavior. It is observed that the compressive strength of these foams strongly depends on porosity, pore size, pore size distribution and pore wall thickness. Among all fabricated foams, Al₂O₃ foams with 20 vol% beads of 10 μm size showed a higher compressive strength of 700 MPa with low porosity (21%) and a higher pore wall thickness (2.8 μm). It is also observed that the pore wall thickness decreased with the increase in beads size and the volume % of the beads, resulting in a low compressive strength value of 8 MPa with a lower pore wall thickness of 1.75 μm at 80 vol% of 40 μm beads. All the foams, irrespective of pore size, showed a typical ceramic failure phenomenon up to 70 vol% of beads; after that, the failure behavior changed to complete open-cell fracture.     

Near-zero-shrinkage Al2O3 ceramic foams with coral-like and hollow-sphere structures via selective laser sintering and reaction bonding

The large shrinkage that ceramics undergo during sintering is a severe challenge for high-performance porous ceramics. In this study, we report a powder-based selective laser sintering (SLS) approach to prepare Al₂O₃ ceramic foams with near-zero shrinkage, high porosity, and outstanding strength. The ceramic foams consist of specific coral-like and hollow-sphere structures derived from the raw Al₂O₃/Al composite powders via reaction bonding (RB). A near-zero shrinkage of 0.91 ± 0.15 % and a high porosity of 73.7 ± 0.2 % can be achieved based on the Kirkendall effect during the oxidation of Al particles. Meanwhile, the reinforced sintering necks and robust bond-bridge connections between hollow-sphere and coral-like structures result in a remarkable bending strength of 7.37 ± 0.37 MPa. This measured strength is more than six times higher than other fabricated samples from spherical Al₂O₃ powders, and the comprehensive performance of ceramic foams prepared by this novel SLS/RB strategy is exceptionally remarkable versus that via conventional forming methods.     

A novel process to high-strength and controlled-shrinkage Al2O3 foams with open-cell by Al powder hollowing technology

Ceramic foams with open-cell structures have attracted extensive attention due to their unique structure and superior properties. But these materials often exhibit the weakness of high sintered shrinkage and low strength at high porosity levels. In this work, novel ceramic foams with open-cell structures have been obtained using Al powder by combining direct foaming and gelation freezing (DF–GF). The foams are assembled by hollow Al₂O₃ particles resulting from the Kirkendall effect, in which expanded particles overcome the shrinkage of sintering. The influence of sintering temperature on the microstructure and properties of foams are investigated. The Al₂O₃ foams show near-zero-shrinkage at 1773 K after undergoing the process of first expansion and then shrinkage. Compared to other conventional open-cell foam, this foam displays relatively high compressive strength of 0.35–2.19 MPa at high porosity levels of 89.45%–94.45%, attributed to hierarchical pore structure and reaction bonding between Al and O₂. This method from pore structure design provides a novel route for the preparation of controlled shrinkage and high-compressive strength alumina foam with open-cell toward potential application.     

Tailoring the microstructure of high porosity Si3N4 foams by direct foaming with mixed surfactants

The mixed surfactants were successfully applied to fabricate the highly porous Si₃N₄ ceramic foams by the direct foaming method. The oppositely charged surfactants mixed in slurries could combined into catanionic surfactant by the electrostatic attraction and facilitate the formation of ultra-stable foams. The microstructure of the Si₃N₄ ceramic foams, including pore structure, mean pore size, pore size distribution and porosity were tailored by varying the mixing ratio of surfactant, mixed surfactants concentration and solid content of the initial slurries. Si₃N₄ ceramic foams with porosity of 92%-97%, mean pore size of 140-240 µm and compressive strength of 0.85-5.38 MPa were obtained by adjusting mixed surfactants between 0.1 and 0.4 wt% and solid content between 22 and 30 vol%. The compressive strength of Si₃N₄ ceramic foams in current work was much higher than most reported results.     

Silicon carbide-based foams derived from foamed SiC-filled phenolic resin by reactive infiltration of silicon

Macro-cellular porous silicon carbide-based foams were fabricated by reactive infiltration of melt silicon into porous carbonaceous preforms pyrolyzed from foamed SiC-filled phenolic resins (PF). The SiC-filled PF foams were prepared at 80 °C with different heating rate. The effect of heating rate on the foaming behavior of the liquid SiC-filled PF mixture and the microstructure of the foams were investigated. The foamed SiC-filled PF was then pyrolyzed at 1000 °C and infiltrated by melt Si at 1600 °C, leading to the formation of open macro-cellular structure. At a heating rate of 6 °C min⁻¹, Si-infiltrated foams with a porosity of ~72% and a mean pore size of ~0.5 mm were obtained. The Si-infiltrated foams with dense struts mainly inherited the pore structure of pyrolyzed preforms. The main phases of SiC-based foams were α-SiC, β-SiC and the remnant Si, which contributed to high compressive strength of the SiC-based foams.     

Preparation and properties of porous alumina with inter-locked platelets structure

Porous alumina ceramics with alumina platelets was prepared by vapor-solid reaction sintering of AlOF mesophase gas by the reaction of HF and Al₂O₃. The effect of heating treatment temperatures on porosity, the formation of inter-locked platelets structure and compressive strength of porous alumina ceramics was determined by Archimedes' method, XRD, SEM and compressive tests. The results indicated that after heating at temperatures from 1300 °C to 1600 °C, the porosity of alumina ceramics decreased from 61.6% to 48.4%. Increasing the heating treatment temperature was beneficial to form inter-locked structure between alumina platelets. The maximum compressive strength of porous ceramics with porosity of 48.4% can reach 29.8 MPa heated at 1600 °C; this strength was attributed to the strong bonding between the alumina platelets.     

High‐temperature oxidation and compressive strength of Cr2AlC MAX phase foams with controlled porosity

Cr₂AlC foams have been processed for the first time containing low (35 vol%), intermediate (53 vol%), and high (75 vol%) content of porosity and three ranges of pore size, 90‐180 μm, 180‐250 μm, and 250‐400 μm. Sacrificial template technique was used as the processing method, utilizing NH₄HCO₃ as a temporary pore former. Cr₂AlC foams exhibited negligible oxidation up to 800°C and excellent response up to 1300°C due to the in‐situ formation of an outer thin continuous protective layer of α‐Al₂O₃. The in‐situ α‐Al₂O₃ protective layer covered seamlessly all the external surface of the pores, even when they present sharp angles and tight corners, reducing significantly the further oxidation of the foams. The compressive strength of the foams was 73 and 13 MPa for 53 vol% and 75 vol% porosity, respectively, which increased up to 128 and 24 MPa after their oxidation at 1200°C for 1 hour. The increase in the compressive strength after the oxidation was caused by the switch from inter‐ to transgranular fracture mode. According to the excellent high‐temperature response, heat exchangers and catalyst supports are the potential application of these foams.     

Waste recycling of coal fly ash: A novel approach to prepare hierarchically porous coal fly ash/Al2O3 ceramic composite with high porosity and high strength templated by emulsion-assisted self-assembly

The coal fly ash (CFA) produced from coal-fired power generation is classified as a common solid waste; thus, improving the recovery and utilization rate of CFA is highly desirable. In this study, a novel strategy using CFA and Al₂O₃ as raw materials, to prepare hierarchically porous ceramic composites that serve as potential candidates for future building materials is developed. In this process, the well-developed self-assembly method in which an anionic modifier is used to prepare hydrophobic powders that form an attractive oil/water network via electrostatic interactions, thereby yielding honeycomb-like structures. In order to explore the mechanism of preparation, five samples with different mixture ratios of alumina and CFA were prepared according to 1: 0, 2: 1, 1: 1, 1: 2, and 0: 1 (Alumina: CFA). Compared with the sample prepared with pure CFA, the as-prepared CFA/Al₂O₃ composite exhibited both superior porosity and high mechanical property. When the porosity is as high as 73 ± 0.17%, the compressive strength is as high as 80.9 ± 3.4mpa (alumina: CFA = 1:1). As the porosity decreases to 49.3 ± 0.7%, the compressive strength reaches 159.33 ± 36.89mpa (alumina: CFA = 1:2). Moreover, this work obtains the highest compressive strength-porosity related B-value in comparison to previously reported CFA-based composites and provides a new insight into the effective recycling of CFA and offers a novel approach to prepare CFA/Al₂O₃ composite with excellent overall mechanical properties.     

Highly porous (La1/5Nd1/5Sm1/5Gd1/5Yb1/5)2Zr2O7 ceramics with ultra-low thermal conductivity

The high-entropy rare earth zirconate (La_1/5Nd_1/5Sm_1/5Gd_1/5Yb_1/5)₂Zr₂O₇ porous ceramics ((5RE_1/5)₂Zr₂O₇ PCs) were prepared using a foam-gel casting-freeze drying method combined with segmented calcination process. The results of SEM, TEM, and XRD analyses of the (5RE_1/5)₂Zr₂O₇ PCs indicated the formation of a defective fluorite crystal structure, with the rare earth elements homogeneously distributed. Meanwhile, the as-prepared (5RE_1/5)₂Zr₂O₇ PCs exhibited high porosity, low bulk density, low thermal conductivity, and relatively high compressive strength. Moreover, the high-temperature thermal conductivity of the samples was evaluated, and the results showed that the (5RE_1/5)₂Zr₂O₇ PCs maintain a thermal conductivity of 0.150 ± 0.002 W m^?1 K^?1 even at 1000 °C. The strategy used in this paper can be extended to the synthesis of other high-entropy porous ceramics with high porosity and low thermal conductivity, which is suitable for applications as thermal insulation materials.     

Carbon nanotube/graphene oxide‐added CaO‐B2O3‐SiO2 glass/Al2O3 composite as substrate for chip‐type supercapacitor

A CaO‐B₂O₃‐SiO₂ (CBS) glass/40 wt% Al₂O₃ composite sintered at 900°C exhibited a dense microstructure with a low porosity of 0.21%. This composite contained Al₂O₃ and anorthite phases, but pure glass sintered at 900°C has small quantities of wollastonite and diopside phases. This composite was measured to have a high bending strength of 323 MPa and thermal conductivity of 3.75 W/(mK). The thermal conductivity increased when the composite was annealed at 850°C after sintering at 900°C, because of the increase in the amount of the anorthite phase. 0.25 wt% graphene oxide and 0.75 wt% multi‐wall carbon nanotubes were added to the CBS/40 wt% Al₂O₃ composite to further enhance the thermal conductivity and bending strength. The specimen sintered at 900°C and subsequently annealed at 850°C exhibited a large bending strength of 420 MPa and thermal conductivity of 5.51 W/(mK), indicating that it would be a highly effective substrate for a chip‐type supercapacitor.     

Direct foaming of macroporous ceramics containing colloidal alumina

Liquid foams containing Al₂O₃ nanoparticles were obtained after direct foaming of a colloidal alumina suspension with ammonium stearate. These systems were stable for at least 24 h and were comprised by small cells (<35 μm). Up to 10 wt% of these foams were added to an ultrastable Al₂O₃-stabilised one and resulted in macroporous samples with high total porosity (>70%). Their green mechanical strength was proportional to the amount of colloidal alumina added, but lower than a composition with calcium aluminate cement. When compared with compositions prepared with colloidal alumina suspension, the colloidal foams resulted in samples with a higher number of small pores (<30 μm) and lower linear shrinkage after firing at 1600 °C for 5 h (~9%). Thus, colloidal alumina foams can be used for processing macroporous refractory ceramics with smaller pores, lower dimensional changes after firing and higher porosity.     

Tailored pore structures and mechanical properties of porous alumina ceramics prepared with corn cob pore-forming agent

In this work, the effects of porosity and different particle sizes of pore-forming agent on the mechanical properties of porous alumina ceramics have been reported. Different grades of porous alumina ceramics were developed using corn cob (CC) of different weight contents (5, 10, 15, and 20 wt%) and particle sizes (<63 µm, 63-125 µm and 125-250 µm) as the pore-forming agent. Experimental results showed that total porosity and pore cavity size of the porous alumina ceramics increased with rising addition of CC pore former. Total porosity increased with increasing particle size of CC with the Al₂O₃-^<63CC₅ sample exhibiting the lowest total porosity of 41.3 vol% while the highest total porosity of 68.1 vol% was exhibited by the Al₂O₃-^125-250CC₂₀. The particle size effect of CC on the mechanical properties revealed that diametral tensile strength and hardness of the porous alumina ceramics deteriorated with increasing particle size of CC pore former. The Al₂O₃-^<63CC₅ sample exhibited the highest diametral tensile strength and hardness of 25.1 MPa and 768.2 HV, respectively, while Al₂O₃-^125-250CC₂₀ exhibited the lowest values of 1.1 MPa and 35.9 HV. Overall, porous alumina ceramics with the smallest pore sizes under each particle size category exhibited superior mechanical properties in their respective categories.     

Constrained sintering of YSZ/Al2O3 composite coatings on metal substrates produced from eletrophoretic deposition

Yttria stabilized zirconia/alumina (YSZ/Al₂O₃) composite coatings were prepared from electrophoretic deposition (EPD), followed by sintering. The constrained sintering of the coatings on metal substrates was characterized with microstructure examination using electron microscopy, mechanical properties examination using nanoindentation, and residual stress measurement using Cr³⁺ fluorescence spectroscopy. The microstructure close to the coating/substrate interface is more porous than that near the surface of the EPD coatings due to the deposition process and the constrained sintering of the coatings. The sintering of the YSZ/Al₂O₃ composite coating took up to 200 h at 1250 °C to achieve the highest density due to the constraint of the substrate. When the coating was sintered at 1000 °C after sintering at 1250 °C for less than 100 h, the compressive stress was generated due to thermal mismatch between the coating and metal substrate, leading to further densification at 1000 °C because of the ‘hot pressing’ effect. The relative densities estimated based on the residual stress measurements are close to the densities measured by the Archimedes method, which excludes an open porosity effect. The densities estimated from the hardness and the modulus measurements are lower than those from the residual stress measurement and the Archimedes method, because it takes account of the open porosity.     

Structure and properties of Al2O3-bonded porous fibrous YSZ ceramics fabricated by aqueous gel-casting

To meet requirements for high porosity and high strength, novel aqueous gel-casting process has been successfully developed to fabricate Al₂O₃-bonded porous fibrous YSZ ceramics with ρ-Al₂O₃ and YSZ fibers as raw materials. Microstructure, phase composition, apparent porosity, bulk density, thermal conductivity, and compressive strength of fabricated porous ceramics were investigated, and effects of fiber content on properties were discussed. According to results, bird nest 3D mesh with interlaced YSZ fibers and Al₂O₃ binder was formed, ensuring the ability to obtain high performance, lightweight ceramics. An increase in the number of YSZ fibers led to more complex interlaced arrangement of fibers and denser network structure of porous ceramics at retaining their stability. Furthermore, their apparent porosity and bulk density increased, whereas thermal conductivity and compressive strength decreased with increasing the fiber content. In particular, comparatively high porosity (71.1–72.7%), low thermal conductivity (0.209–0.503 W/mK), and relatively high compressive strength (3.45–4.24 MPa) were obtained for as-prepared porous ceramics, making them promising for applications in filters, thermal insulation materials, and separation membranes.     

Low thermal conductivity in porous SiC–SiO2–Al2O3–TiO2 ceramics induced by multiphase thermal resistance

The introduction of multiple heterogeneous interfaces in a ceramic is an efficient way to increase its thermal resistance. Novel porous SiC–SiO₂–Al₂O₃–TiO₂ (SSAT) ceramics were fabricated to achieve multiple heterogeneous interfaces by sintering equal volumes of SiC, SiO₂, Al₂O₃, and TiO₂ compacted powders with polysiloxane as a bonding phase and carbon as a template at 600 °C in air. The porosity could be controlled between 66% and 74% by adjusting the amounts of polysiloxane and the carbon template. The lowest thermal conductivity (0.059 W/(m·K) at 74% porosity) obtained in this study is an order of magnitude lower than those (0.2–1.3 W/(m·K)) of porous monolithic SiC, SiO₂, Al₂O₃, and TiO₂ ceramics at an equivalent porosity. The typical specific compressive strength value of the porous SSAT ceramics at 74% porosity was 3.2 MPa cm³/g.     

Rapid Sintering of Ceramics with Gradient Porous Structure by Asymmetric Thermal Radiation

In this study, thermal radiation was employed for sintering silicon carbide foams that achieved a gradient porous structure. The simultaneous use of graphite and carbon fiber reinforced carbon composite (C_f/C) radiators resulted in an axial temperature gradient of ~600°C along the cylindrical sample, as confirmed by both numerical simulation and experimental measurement. By sintering the cylinder top at 1600°C for 5 min, the porous SiC body achieved an axial pore size gradient from ~106 ± 36 μm to ~250 ± 84 μm and an open porosity from 41.4 to 79.8 vol%. This work indicates the potential of sintering by intense thermal radiation technique for rapid manufacturing functionally graded materials through asymmetric assembly of thermal radiators.