In vitro dissolution behavior of SiO<Subscript>2</Subscript>–MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–K<Subscript>2</Subscript>O–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–F glass–ceramic system

Herein, we report the results of the in vitro dissolution tests, which were carried out by immersing the selected glass-ceramic samples in artificial saliva (AS) for various time periods of up to 42 days. In our experiments, the SiO(2)-MgO-Al(2)O(3)-K(2)O-B(2)O(3)-F glass ceramics with different crystal morphology and crystal content were used and a comparison is also made with the baseline glass samples (without any crystals). The bioactivity of the samples was probed by measuring the changes in pH, ionic conductivity and ionic concentration of AS following in vitro dissolution experiments. High resistance of the selected glass-ceramic samples against in vitro leaching has been demonstrated by minimal weight loss (<1%) and insignificant density change, even after 6 weeks of dissolution in artificial saliva. While XRD analysis reveals the change in surface texture of the crystalline phase, FT-IR analysis weakly indicated the Ca-P compound formation on the leached surface. The experimental measurements further indicate that the leaching of F(-), Mg(2+) ions from the sample surface commonly causes the change in the surface chemistry. Furthermore, the presence of (Ca, P, O)-rich mineralized deposits on the leached glass-ceramic surface as well as the decrease in Ca(2+) ion concentrations in the leaching solutions (compared to that in the initial AS solution) provide evidences of the moderate bioactive or mild biomineralisation behaviour of investigated glass-ceramics.     

Crystallization and microstructural evolution of MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>–TiO<Subscript>2</Subscript>–La<Subscript>2</Subscript>O<Subscript>3</Subscript> glass-ceramics

Crystallization and microstructure of glasses with the molar compositions 1MgO·1.2Al₂O₃·2.8SiO₂·1.2TiO₂·xLa₂O₃ (x = 0.1 and 0.4) were thermally treated at different temperatures in the range from 950 to 1250 °C and then analyzed by X-ray diffraction and scanning electron microscopy, in combination with energy-dispersive X-ray spectroscopy and electron backscatter diffraction. It was found that the microstructure is first homogeneous with the precipitation of randomly distributed crystals and then indialite domains with embedded perrierite and rutile crystals are formed. For higher temperatures or prolonged times, more domains appear and expand into the bulk of the sample. Finally, the entire sample consists of the indialite domains and the boundaries that are enriched in rutile, perrierite, and magnesium aluminotitanate. Nevertheless, very distinct differences are observed between the samples with different La₂O₃ concentrations. For the sample with x = 0.4, the domains were detected at lower temperatures, while the quantity and size of the domains increase faster due to the promoted precipitation of indialite. For the sample with x = 0.1, in addition to the domain boundaries, secondary boundaries between the “regions” (assemblages of the domains) are observed in a larger length scale. The average size of the crystalline phases found between the “regions” is larger than that typically observed at the domain boundaries. The sizes of the crystals at the boundaries decrease with higher concentrations of La₂O₃, and the crystals (especially perrierite) within the domains become larger, resulting in a more homogeneous microstructure. This results in better dielectric properties, i.e., much higher quality factor for the sample with x = 0.4 in comparison to that with x = 0.1 after heat-treatment at 1150 or 1250 °C.     

Wear resistance of electrodeposited Ni–B and Ni–B–Si<Subscript>3</Subscript>N<Subscript>4</Subscript> composite coatings

The wear resistance of electrodeposited (ED) Ni–B and Ni–B–Si₃N₄ composite coatings is compared. The effect of incorporation of Si₃N₄ particles in the ED Ni–B matrix on the surface morphology, structural characteristics and microhardness has been evaluated to correlate the wear resistance. The wear mechanism of ED Ni–B and Ni–B–Si₃N₄ composite coatings appears to be similar; both involve intensive plastic deformation of the coating due to the ploughing action of the hard counter disc. However, the extent of wear damage is relatively small for ED Ni–B–Si₃N₄ composite coatings.     

Evaluation of CaO–SiO<Subscript>2</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–Na<Subscript>2</Subscript>O–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> bioglass-ceramics for hyperthermia application

Magnetic bioglass ceramics (MBC) are being considered for use as thermoseeds in hyperthermia treatment of cancer. While the bioactivity in MBCs is attributed to the formation of the bone minerals such as crystalline apatite, wollastonite, etc. in a physiological environment, the magnetic property arises from the magnetite [Fe₃O₄] present in these implant materials. A new set of bioglasses with compositions 41CaO · (52 ? x)SiO₂ · 4P₂O₅  · xFe₂O₃ · 3Na₂O (2 ≤ x ≤ 10 mol% Fe₂O₃) have been prepared by melt quenching method. The as-quenched glasses were then heat treated at 1050°C for 3 h to obtain the glass-ceramics. The structure and microstructure of the samples were characterized using X-ray diffraction and microscopy techniques. X-ray diffraction data revealed the presence of magnetite in the heat treated samples with x ≥ 2 mol% Fe₂O₃. Room temperature magnetic property of the heat treated samples was investigated using a Vibrating Sample Magnetometer. Field scans up to 20 kOe revealed that the glass ceramic samples had a high saturation magnetization and low coercivity. Room temperature hysteresis cycles were also recorded at 500 Oe to ascertain the magnetic properties at clinically amenable field strengths. The area under the magnetic hysteresis loop is a measure of the heat generated by the MBC. The coercivity of the samples is another important factor for hyperthermia applications. The area under the loop increases with an increase in Fe₂O₃ molar concentration and the. coercivity decreases with an increase in Fe₂O₃ molar concentration The evolution of magnetic properties in these MBCs as a function of Fe₂O₃ molar concentration is discussed and correlated with the amount of magnetite present in them.     

Structural and electrical properties of Bi<Subscript>1/2</Subscript>Na<Subscript>1/2</Subscript>TiO<Subscript>3</Subscript>–BaTiO<Subscript>3</Subscript>–Sr<Subscript>3</Subscript>CuNb<Subscript>2</Subscript>O<Subscript>9</Subscript> lead-free piezoelectric ceramics

The structure, microstructure, field-induced strain, ferroelectric, piezoelectric and dielectric properties of (1 ? x) (Bi_0.5Na_0.5)_0.935Ba_0.065TiO₃–xSr₃CuNb₂O₉ (BNT-BT6.5–xSCN, with x = 0, 0.003, 0.006, 0.009) ceramics were investigated. X-ray diffraction patterns show that all samples are pure perovskite structure and Sr₃CuNb₂O₉ (SCN) effectively diffused into the 0.935Bi_0.5Na_0.5TiO₃–0.065BaTiO₃ (BNT–BT6.5) solid solution which also reflected in the Raman spectra and the energy disperse spectroscopy (EDS) analysis. With the increases of SCN content, the coercive field (E _c  = 18.41 kV/cm) decreases greatly, whereas the remnant polarization (P _r  = 29.11 μC/cm²) increases a little at x = 0.003 which is showed in the polarization hysteresis (P–E) loops, the result indicate that the ferroelectric order would be disrupted. Around critical composition (x = 0.003) at a driving field of 60 kV/cm, a large unipolar strain of 0.29 % with a normalized strain (d ₃₃ ^*  = 483 pm/V) is obtained at room temperature. The results indicate that BNT-BT6.5-xSCN ceramics with excellent properties are promising to replace lead-based piezoelectric ceramics and can be used in practical applications.     

Phase equilibria in the Tl<Subscript>5</Subscript>Te<Subscript>3</Subscript>–Tl<Subscript>9</Subscript>BiTe<Subscript>6</Subscript>–Tl<Subscript>9</Subscript>TbTe<Subscript>6</Subscript> system

Phase equilibria in the Tl₅Te₃–Tl₉BiTe₆–Tl₉TbTe₆ system have been studied using differential thermal analysis, X-ray diffraction, and microhardness measurements. We have mapped out a number of vertical sections, the 760-K isothermal section of its phase diagram, and projections of its liquidus and solidus surfaces. The composition dependences of lattice parameters and microhardness have been obtained. The system has been shown to contain a continuous series of solid solutions, which crystallize in a tetragonal structure (Tl₅Te₃ type, sp. gr. I4/mcm).     

Preparation and characterization of Li<Subscript>2</Subscript>O–CaO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–SiO<Subscript>2</Subscript> glasses as bioactive material

The aim of the present investigation was to study the role of Al₂O₃ in the Li₂O–CaO–P₂O₅–SiO₂ bioactive glass for improving the bioactivity and other physico-mechanical properties of glass. A comparative study on structural and physico-mechanical properties and bioactivity of glasses were reported. The structural properties of glasses were investigated by X-ray diffraction, Fourier transform infrared spectrometry, scanning electron microscopy and the bioactivity of the glasses was evaluated by in vitro test in simulated body fluid (SBF). Density, compressive strength, Vickers hardness and ultrasonic wave velocity of glass samples were measured to investigate physical and mechanical properties. Results indicated that partial molar replacement of Li₂O by Al₂O₃ resulted in a significant increase in mechanical properties of glasses. In vitro studies of samples in SBF had shown that the pH of the solution increased after immersion of samples during the initial stage and then after reaching maxima it decreased with the increase in the immersion time. In vitro test in SBF indicated that the addition of Al₂O₃ up to 1.5 mol% resulted in an increase in bioactivity where as further addition of Al₂O₃ caused a decrease in bioactivity of the samples. The biocompatibility of these bioactive glass samples was studied using human osteoblast (MG-63) cell lines. The results obtained suggested that Li₂O–CaO–Al₂O₃–P₂O₅–SiO₂-based bioactive glasses containing alumina would be potential materials for biomedical applications.     

Microwave dielectric properties of Sr<Subscript>0.7</Subscript>Ce<Subscript>0.2</Subscript>TiO<Subscript>3</Subscript>–Sr(Mg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript> ceramics

xSr_0.7Ce_0.2TiO₃–(1???x)Sr(Mg_1/3Nb_2/3)O₃ ceramics, referred to xSCT–(1???x)SMN, were successfully produced by conventional solid-state sintered technology. The compounds, belonging to perovskites with a secondary phase of CeO₂, can be detected even with x down to 0.1 of SCT composition. The overall trend for grain growth illustrates the increase with increasing SCT doping level. The Raman peak at 825 cm^?1 splits into two peaks and causes red shift phenomenon. XPS spectra indicate that Ti and Nb ions exist respectively in tetravalence and pentavalence, and Ce ions exist in trivalence and tetravalence. Dielectrics constant (ε _r ) of SCT–SMN ceramics gradually increases with increasing theoretical dielectric polarizabilities. A wider width of the 825 cm^?1 for FWHM of A_1g mode Raman peaks suggests to a lower Q?×?f value. The increasing tolerance factor in agreement with temperature coefficient of resonant frequency (τ _f ), denotes that the rise of perovskite symmetry. The 0.1SCT–0.9SMN ceramic sintered at 1450?°C for 4 h illustrates excellent microwave dielectric properties with ε _r ?~?35.4, Q?×?f?~?11282 GHz and τ _f ?~?1.7 ppm/°C. Activation energies of 0.1SCT–0.9SMN ceramic at 100, 300 and 500 V, are ~0.436, 0.427 and 0.331 eV, respectively, indicative of a decreased trend with external electric field.     

Effect of sintering temperatures on properties of BaO–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> glass/silica composites for CBGA package

BaO–B₂O₃–SiO₂–Al₂O₃ (BBSA) glass/silica composites synthesized by solid-state reaction method were developed for CBGA packages, and the effects of sintering temperature (900–950 °C) on the phase transformation, microstructure, thermal, mechanical and electrical properties were investigated. XRD results show that the major phases quartz and cristobalite, and the minor phase BaSi₂O₅ are detected in BBSA composites. Furthermore, it was found that the quartz phase transforms to cristobalite phase at 930–940 °C. The formation of cristobalite phase with higher coefficient of thermal expansion (CTE) led to the increase of CTE value of BBSA composites. However, excessive cristobalite phase content would degrade the mechanical properties and the linearity of thermal expansion of the ceramics. BBSA composites sintered at 920 °C exhibited excellent properties: low dielectric constant and loss (ε_r = 6.2, tanδ = 10^?4 at 1 MHz), high bending strength (179 MPa), high CTE (12.19 ppm/°C) as well as superior linearity of the thermal expansion.     

Influence of Bi substitution on microwave dielectric properties of BaO–La<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sm<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript> ceramics

The influences of Bi substitution on microwave dielectric properties of Ba₄(La_0.5Sm_0.5)_9.33Ti₁₈O₅₄ solid solutions were investigated. Dielectric ceramics with general formula Ba₄(La_(0.5−z)Sm_0.5Bi _z )_9.33Ti₁₈O₅₄, z = 0.0–0.2 were prepared by conventional solid state route. The structural analysis of all the samples was carried out by X-ray diffraction and scanning electron microscopy. The dielectric properties were investigated as a function of Bi contents using open-ended coaxial probe method in the frequency range 0.3–3.0 GHz at room temperature. Dielectric constant varies from 83 to 88 and loss tangent from 2.1 × 10⁻³ to 5.5 × 10⁻³ at 3 GHz with temperature coefficient of resonant frequency changing from 106.7 to −8.4 ppm/oC as Bi contents increases from z = 0.00–0.20. It has been found that dielectric constant and temperature coefficient of resonant frequency improve whereas loss tangent is adversely affected with increase in Bi substitution.     

Catalytic combustion of methane over Pt and PdO-supported CeO<Subscript>2</Subscript>–ZrO<Subscript>2</Subscript>–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Catalytic combustion of methane was investigated on Pt and PdO-supported CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts prepared by a wet impregnation method in the presence of polyvinylpyrrolidone. The catalysts were characterized by X-ray fluorescence analysis, X-ray powder diffraction, X-ray photoelectron spectra, transmission electron microscopy, and BET specific surface area measurements. The Pt/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ and PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts were selective for the total oxidation of methane into carbon dioxide and steam, and no by-products such as HCHO, CO, and H₂ were obtained. The catalytic activities of the PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts were relatively higher than those of the Pt-supported catalysts, due to the facile re-oxidation of metallic Pd into PdO based on lattice oxygen supplied from the CeO₂–ZrO₂–Bi₂O₃ bulk. A decrease in the calcination temperature during the preparation process was found to be effective in enhancing the specific surface area of the catalysts, whereby particle agglomeration was inhibited. Optimization of the PdO amount and calcination temperature enabled complete oxidation of methane at temperatures as low as 320 °C on the 11.6 wt% PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalyst prepared at 400 °C.     

Tunable Microwave Absorption Properties in Ni–Zn-Substituted BaCoTiFe<Subscript>10</Subscript>O<Subscript>19</Subscript>

Ni–Zn-substituted BaCoTiFe₁₀O₁₉ were successfully prepared by a sol-gel combustion method. The grain size of samples is about 150–800 nm ,and the grains first increase and then decrease with increasing x. Through XRD analysis, all diffraction peaks correspond to the BaTiCoFe₁₀O₁₉ and no other phase signal is detected. With x = 0.3, the saturation magnetization (M _s) is biggest (66.7 emu/g) and its coercivity (H _c) is 172.3 Oe. The curves μ ^″ ? μ ^′ have distorted semicircles, and each semicircle has an extremum. Each extremum of μ ^″ ? μ ^′ curve corresponds to a peak of μ ^″ curve and has response to reflection loss (RL), which is further illuminated. When x = 0.3, the widest bandwidth of R L ≤?10 dB is 6.13 GHz (9.68–15.81 GHz) at d = 2.6 mm. The RL curve closely relates to distorted semicircle of μ ^″ ? μ ^′ curve, and the relation is also deeply illuminated, which is beneficial to study absorption materials.     

Fabrication of Yb<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–SiO<Subscript>2</Subscript> Optical Fibers with a Perfect Step-Index Profile by the MCVD Process

An all-vapor phase MCVD process has been proposed for the fabrication of fiber preforms with a Yb₂O₃–Al₂O₃–P₂O₅–SiO₂ multicomponent glass core. We have investigated the tubular preform collapse into a rod and demonstrated approaches capable of preventing P₂O₅ losses in the central part of the core during the collapse process. Preforms with a flat, perfect step-index profile have been fabricated.     

Compositional dependence of the structural and dielectric properties of Li<Subscript>2</Subscript>O–GeO<Subscript>2</Subscript>–ZnO–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

(10Li₂O–20GeO₂–30ZnO–(40-x)Bi₂O₃–xFe₂O₃ where x = 0.0, 3, 6, and 9 mol%) glasses were prepared. A number of studies, viz. density, differential thermal analysis, FT-IR spectra, DC and AC conductivities, and dielectric properties (constant ε′, loss tan δ, AC conductivity, σ _ac, over a wide range of frequency and temperature) of these glasses were carried out as a function of iron ion concentration. The analysis of the results indicate that, the density and molar volume decrease with an increasing of iron content indicates structural changes of the glass matrix. The glass transition temperature T _g and onset of crystallization temperature T _x increase with the variation of concentration of Fe₂O₃ referred to the growth in the network connectivity in this concentration range, while glass-forming ability parameter ΔT decrease with increase Fe₂O₃ content, indicates an increasing concentration of iron ions that take part in the network-modifying positions. The FT-IR spectra evidenced that the main structural units are BiO₃, BiO₆, ZnO₄, GeO₄, and GeO₆. The structural changes observed by varying the Fe₂O₃ content in these glasses and evidenced by FTIR investigation suggest that the iron ions play a network modifier role in these glasses while Bi₂O₃, GeO₂, and ZnO play the role of network formers. The temperature dependence of DC and AC conductivities at different frequencies was analyzed using Mott’s small polaron hopping model and, the high temperature activation energies have been estimated and discussed. The dielectric constant and dielectric loss increased with increase in temperature and Fe₂O₃ content.     

Phase equilibria in the Tl<Subscript>2</Subscript>Te–Tl<Subscript>5</Subscript>Te<Subscript>3</Subscript>–Tl<Subscript>9</Subscript>TbTe<Subscript>6</Subscript> system

The Tl₂Te–Tl₅Te₃–Tl₉TbTe₆ system has been studied using differential thermal analysis, X-ray diffraction, and microhardness measurements. We have mapped out a number of vertical sections, the 680 K isothermal section of its phase diagram, and projections of its polythermal projections of its liquidus and solidus surfaces. The field of solid solutions with the Tl₅Te₃ structure (δ-phase) has been shown to account for more than 90% of the area of the composition triangle. Tl₂Te-based solid solutions (α-phase) exist in a narrow composition region.     

Phase relations in the K<Subscript>2</Subscript>MoO<Subscript>4</Subscript>–Ln<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>–Zr(MoO<Subscript>4</Subscript>)<Subscript>2</Subscript> (Ln = La–Lu,Y) systems

We have studied phase relations in the K₂MoO₄–Ln₂(MoO₄)₃–Zr(MoO₄)₂ (Ln = La–Lu, Y) systems by the method of “intersecting cuts,” identified pseudobinary joins in their composition triangles, and constructed their phase compatibility diagrams. The systems have been shown to contain new ternary molybdates with the general formula K₅LnZr(MoO₄)₆ (Ln = Dy–Lu and Y). The thermal characteristics of the synthesized compounds have been studied by differential scanning calorimetry in the temperature range 25–700°C. The new ternary molybdates crystallize in a trigonal structure (sp. gr. R\(\bar 3\)c, Z = 6).     

Hardness properties and microscopic investigation of crack–crystal interaction in SiO<Subscript>2</Subscript>–MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–K<Subscript>2</Subscript>O–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–F glass ceramic system

In view of the potential engineering applications requiring machinability and wear resistance, the present work focuses to evaluate hardness property and to understand the damage behavior of some selected glass–ceramics having different crystal morphologies with SiO₂–MgO–Al₂O₃–K₂O–B₂O₃–F composition, using static micro-indentation tests as well as dynamic scratch tests, respectively. Vickers hardness of up to 5.5 GPa has been measured in glass–ceramics containing plate like mica crystals. Scratch tests at a high load of 50 N in artificial saliva were carried out in order to simulate the crack–microstructure interaction during real-time abrasion wear and machining operation. The experimental observations indicate that the novel “spherulitic-dendritic” shaped crystals, similar to the plate like crystals, have the potential to hinder the scratching induced crack propagation. In particular, such potential of the ‘spherulitic-dendritic’ crystals become more effective due to the larger interfacial area with the glass matrix as well as the dendritic structure of each mica plate, which helps in crack deflection and crack blunting, to a larger extent. While modest damage tolerant behavior is observed in case of ‘spherulitic-dendritic’ crystal containing material, severe brittle fracture of plate like crystals were noted, when both were scratched at 50 N load.     

The crystallographic orientation relationship between Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript> in the composite material Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al–Mg–Si alloy

The formation mechanism of spinels on Al₂O₃ particles in the Al₂O₃/Al–1.0 mass% Mg₂Si alloy composite material has been investigated by transmission electron microscopy (TEM) in order to determine the crystallographic orientation relationship. A thin sample of the Al₂O₃/Al–Mg–Si alloy composite material was obtained by the FIB method, and the orientation relationship between Al₂O₃ and MgAl₂O₄, which was formed on the surface of Al₂O₃ particles, was discovered by the TEM technique as follows:

Frequency dependence of dielectric properties of CaO–SrO–Li<Subscript>2</Subscript>O–Ln<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript> ceramics

CaO–SrO–Li₂O–Ln₂O₃–TiO₂ ceramics were prepared by solid state reaction method, where Ln₂O₃ consists of equal proportions of Nd₂O₃ and Sm₂O₃. Dielectric properties and crystal structure were investigated with respect to the content of TiO₂. Single phase with an orthorhombic perovskites structure was formed within the composition range of investigation. The frequency dependence of dielectric properties of the present ceramics was extensively investigated. Dielectric constant was less sensitive to frequency. However, dielectric loss and temperature coefficients were both very sensitive to frequency and gradually decreased with increasing frequency, such as the variation was more than ten times between 1 MHz and several GHz. The relationship between the temperature coefficient and dielectric loss was also discussed at different frequencies. And the mechanism of the frequency dependence was discussed in term of the role of Li ions.     

Spectroscopic characterisation of local structure in Y<Subscript>2</Subscript>O<Subscript>3</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses doped with gadolinium

Gadolinium doped bismuth borate glasses containing up to 30 mol% Y₂O₃ were prepared by fast melt quenching method. The effect of yttrium on the local order in 3B₂O₃ · Bi₂O₃ and B₂O₃ · Bi₂O₃ glass matrices, particularly on the bismuth sites, was investigated by infrared (IR) spectroscopy and electron paramagnetic resonance (EPR) of Gd³⁺ ions. The IR results show that the local structure is more ordered in the glass system with higher bismuth content and the progressive addition of yttrium increases the local disorder in both bismuth–borate glass matrices. The EPR results indicate that Gd³⁺ ions occupy both bismuth and yttrium sites and reflect the same structural disorder like that suggested by IR results.