Improved the efficiency of small molecule organic solar cell by double anode buffer layers

Small molecule organic solar cell with an optimized hybrid planar-mixed molecular heterojunction (PM-HJ) structure of indium tin oxide (ITO)/ poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT: PSS) doped with 4 wt% sorbitol/ pentacene (2 nm)/ copper phthalocyanine (CuPc) (10 nm)/ CuPc: C₆₀ mixed (20 nm)/ fullerene (C₆₀) (20 nm)/ bathocuproine (BCP) (10 nm)/Al was fabricated. PEDOT: PSS layer doped with 4 wt% sorbitol and pentacene layer were used as interlayers between the ITO anode and CuPc layer to help the hole transport. And then the short-circuit current (J_sc) of solar cell was enhanced by inserting both the PEDOT: PSS (4 wt% sorbitol) and the pentacene, resulting in a 400% enhancement in power conversion efficiency (PCE). The maximum PCE of 3.9% was obtained under 1sun standard AM1.5G solar illumination of 100 mW/cm².     

Low bandgap carbazole copolymers containing an electron-withdrawing side chain for solar cell applications

A new series of low bandgap carbazole copolymers containing an electron-withdrawing moiety as a side chain, via Suzuki, Yamamoto, and Stille polymerization reactions has been synthesized. Their bandgaps and molecular energy levels can be tuned by copolymerizing with different conjugated electron-donating units. The resulting copolymers have low optical and electrochemical bandgaps. The optical bandgaps of the copolymers range from 1.79 to 1.24 eV. In order to investigate their photovoltaic properties, polymer solar cell devices based on low bandgap copolymers were fabricated with a structure of ITO/PEDOT:PSS/copolymers:PCBM/Al, under the illumination of AM 1.5 G, 100 mW/cm². The power conversion efficiencies (PCE) of the polymer solar cells based on these low bandgap copolymers were measured. The best performance was obtained by using PC-CARB as the electron donor and 6,6-phenyl C₇₁-butyric acid methyl ester (PC₇₁BM) as the electron acceptor. The PCE of the solar cell based on PC-CARB/P₇₁CBM (1:4) was 1.27% with an open-circuit voltage (V_oc) of 0.65 V, and a short-circuit current (J_sc) of 6.69 mA/cm².     

Organic solar cells with 2-Thenylmercaptan/AU self-assembly film as buffer layer

The interface between an electrode and the organic active layer is an important factor in organic solar cells (OSCs) that influences the power conversion efficiency (PCE). In this report, a buffer layer of 2-thenylmercaptan/Au self-assembly film is introduced into OSCs as a substitute for the poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT: PSS) layer. The electrode/active layer interface is meliorated by Au-S coordinate bond of self assembly after applying this buffer layer. The series resistance reduces from 20 Ω cm² in a device based on PEDOT:PSS to 10.2 Ω cm². Correspondingly, the fill factor (FF) increases from 0.50 to 0.64. Moreover, due to the dipole of this self-assembled layer, the open circuit voltage (V_oc) also increases slightly from 0.54 V to 0.56 V and the PCE reaches 2.5%.     

Solution processable quinacridone based materials as acceptor for organic heterojunction solar cells

Two series of novel quinacridone (QA) based materials that combined a strong absorption over a broad range in visible region with good electrical characteristics, which were used as the new electron-accepting materials for organic solar cells, are explored. Unique cyclic compounds 1-6 are synthesized by incorporating electron withdrawing groups (CN, COOH) at carbonyl position of alkyl substituted quinacridones, which lead to the compounds possessing the characteristics of solution-processed and being suitable for photovoltaic applications. Heterojunction solar cells with simple device configuration using these soluble materials as acceptor and effective donor poly (3-hexyl thiophene) (P3HT) were fabricated. The maximum power conversion efficiency (PCE) achieved in the solar cell based on compound 5 is 0.42% under simulated AM 1.5 solar irradiation with J_sc=1.80 mA cm⁻², V_oc=0.50 V and FF=47%. Although the aimed devices just exhibit moderate PCE, our results clearly suggest that the new-type electron-accepting materials different from fullerene have great potential as acceptor in heterojunction solar cell due to many advantages of the QA derivatives such as relatively inexpensive, good electrochemical stability and could be readily modified.     

Triphenylamine-substituted methanofullerene derivatives for enhanced open-circuit voltages and efficiencies in polymer solar cells

A new class of triphenylamine substituted methanofullerene derivatives, bis(4'-(diphenylamino)biphenyl-4-yl)methanofullerene (1) and the bisadduct (2), were synthesized. The incident photon to current efficiency (IPCE) studies revealed that the diphenylamino components have contribution to the photocurrent that expands the light harvesting window around 400 nm. When being blended with poly (3-hexylthiophene) (P3HT) to fabricate the solar cell, the device of P3HT:1 (1:0.7) shows high open circuit voltage (V_oc) of 0.69 V under the illumination of AM 1.5, 100 mW/cm² with high power conversion efficiency (PCE) of 3.16%, which is about 0.1 V higher than that of the corresponding [6,6]-phenyl C₆₁ butyric acid methyl ester (PCBM) devices. This indicates that the arylamine substituents on 1 have played some special roles on the high V_oc performance. Similar effects are also observed for 2. The device of P3HT:2 (1:1) shows even higher V_oc of 0.87 V with the PCE of 1.83%. These results indicate that 1 and 2 are alternative high performance acceptors.     

Polymer photovoltaic devices using highly conductive poly(3,4-ethylenedioxythiophene-methanol) electrode

In this work, modified poly(3,4-ethylenedioxythiophene) (PEDOT) was used as an anode in polymer photovoltaic devices (PVDs) based on poly(3-hexylthiophene) (P3HT):[6,6]-phenyl-C₆₀-butyric acid methyl ester (PCBM). We synthesized poly(3,4-ethylenedioxythiophene methanol) (PEDTM) with a transmittance of 87% (at 510 nm) and a conductivity of 700 S/cm. PEDTM was applied in photovoltaic devices as a hole transporting layer on indium-tin oxide (ITO) electrode as well as a direct anode layer. PVDs with PEDTM as hole transporting layers on ITO showed a very high short-circuit density of 14.87 mA/cm² and power conversion efficiency of 2.67% under an illumination of AM 1.5 G (100 mW/cm²). In addition, we also fabricated ITO-free PVDs using PEDTM as an anode, which exhibited a performance of 0.61% with a result of J_sc of 4.48 mA/cm², V_oc of 0.51 V, and FF of 27%.     

Air-stable triarylamine-based amorphous polymer as donor material for bulk-heterojunction organic solar cells

A new air-stable triarylamine-based amorphous polymer, TSP-T11, which consists of thiophene and triarylamine units, can be successfully utilized to fabricate bulk-heterojunction organic photovoltaics (OPVs) using PC₆₀BM or PC₇₀BM as acceptor materials. The highest level of performance of OPVs optimized at TSP-T11:PC₇₀BM (weight ratios of 1:4) with thicknesses of 68 nm exhibited an open circuit voltage (V_oc) of 0.75 V, a short circuit current (J_sc) of 8.03 mA cm⁻², and a power-conversion efficiency (PCE) of 2.22% under simulated air mass 1.5 solar irradiation at 100 mW cm⁻². Although TSP-T11 has a lower hole mobility (1.5×10⁻⁴ cm² V⁻¹ s⁻¹) than P3HT, the use of amorphous film of TSP-T11 as a donor material for OPVs offers advantages over the use of polycrystalline film of P3HT in terms of its air-stability and pinhole-free homogeneous morphology.     

Patternable solution process for fabrication of flexible polymer solar cells using PDMS

PH 500, a highly conducting poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS), is a typical conducting polymer anode material used in organic electric devices. However, it has the disadvantages of low conductivity and poor surface roughness and requires a patterning method for the electrode through including the laser and plasma. In this paper, therefore, the conducting polymer ink for a transparent anode was formulated by adding dimethyl sulfoxide (DMSO) and BYK-333 as the surfactant to enhance the conductivity and surface roughness. The conducting polymer anode was patterned through the application of a new patterning method that used polydimethylsiloxane (PDMS) on a flexible substrate. In addition, a photoactive layer was formed by applying the new patterning method to the conventional brush painting method in which patterning had previously been impossible. The resulting material was compared with the device fabricated by the spin coating method. The fabricated flexible polymer solar cells (PSCs) exhibited short-circuit current density (J_sc), open-circuit voltage (V_oc), fill factor (FF) and power conversion efficiency (PCE) values of 4.2 mA/cm², 0.878 V, 26.5% and 0.98%, respectively, which represented an efficiency improvement of 38% over those fabricated by the spin coating method. Meanwhile, the J_sc value was increased when the series resistance (R_s) decreased to 150 Ω cm².     

Fused thiophene/quinoxaline low band gap polymers for photovoltaic's with increased photochemical stability

We investigate a family of low band-gap polymers based on the common acceptor moiety 2,3-bis-(3-octyloxyphenyl)quinoxaline (Q) combined with thiophene (T) or the fused thiophene systems: benzo[2,1-b:3,4-b′]-dithiophene (BDT) or dithieno[3,2-b,2′,3′-d]-thiophene (DTT). The photochemical stability of the three polymers was examined and compared to P3HT. They were found to be substantially more robust than P3HT with a ranking of DTTQ>BDTQ>TQ1?P3HT, indicating that the fused ring systems of DTT and BDT impart a large degree of photochemical stability than thiophene. Furthermore devices with normal and inverted geometry were prepared and tested in air. The normal geometry devices showed the highest efficiencies compared to the inverted, in particular owing to a higher V_oc, with TQ1 being the most efficient with a power conversion efficiency (PCE) of 1.5% (1000 W m⁻², AM1.5 G). For the inverted devices TQ1 and DTTQ showed the best PCEs of 0.9%.     

Influence of n-type chemical doping layer on the performance of organic photovoltaic solar cells

We report the performance improvement of organic solar cell by addition of an n-type chemical doping layer in organic bulk heterojunction device. The power conversion efficiency (PCE) of P3HT and PCBM-71 based polymer solar cells increases by adding a mixture of TCNQ (7,7,8,8-tetracyanoquinodimethane) and LCV (Leucocrystal violet) between active layer and cathode electrode. The PCE of the cell increases by 14% compared to the control cell with Al-only cathode electrode. The device with an organic n-doped layer shows the J_SC of 8.88 mA/cm², V_OC of 0.51 V, FF of 60.1%, and thus the PCE of 2.72% under AM1.5 illumination of 100 mW/cm².     

Influence of the growth parameters of p-CdTe thin films on the performance of Au-Cu/p-CdTe/n-CdO type solar cells

R.F. sputter deposition of Sb doped CdTe thin films was carried out with targets containing different amounts of antimony (C_T: 0, 2.5, 10 and 20 at.%). The substrates were kept at different temperatures (T_s) of 200, 275, 350 and 450 °C. Three different argon pressure values: 2.5, 5 and 15 mTorr were used. The lowest dark resistivity (ρ) at room temperature (RT) was 9.0 × 10⁵ Ω cm, which is one of the lowest values reported in the literature for Sb doped CdTe. Highly transparent (∼90%) and conductive (ρ = 3.7 × 10⁻⁴ Ω cm) F doped CdO (n-type) thin films, prepared at room temperature by the sol-gel method, were employed as window and top-contact. The configuration of the fabricated solar cell was (Au-Cu)/p-CdTe/n-CdO/glass. Open-circuit voltage (V_oc) and short-circuit current density (J_sc) at room temperature have the highest values for high T_s, low P_g and C_T = 10 at.%. Despite the fact that V_oc and J_sc are lower than those reported in the literature, we think this work is useful as a basis for the search of more competitive CdTe/CdO based PV devices.     

Molecular engineering of Diketopyrrolopyrrole-based photosensitizer for solution processed small molecule bulk heterojunction solar cells

New symmetrical low band-gap small molecule materials, DPP-bis[ter-3HT-TPA] and DPP-bis[ter-3HT] as novel derivatives of Diketopyrrolopyrrole-thiophene with/without triphenylamine (TPA) end group have been synthesized and characterized. And the effects of TPA moiety were investigated. Compared to DPP-bis[ter-3HT], DPP-bis[ter-3HT-TPA] shows red-shifted absorption and significantly higher molar absorption coefficient. And the HOMO level of DPP-bis[ter-3HT-TPA] is elevated than DPP-bis[ter-3HT]. Moreover, DPP-bis[ter-3HT-TPA] exhibited one order higher hole mobility than DPP-bis[ter-3HT], suggesting that TPA contributes to a better hole mobility. The bulk-heterojunction photovoltaic devices with DPP-bis[ter-3HT-TPA] showed better efficiencies than DPP-bis[ter-3HT], showing the best power-conversion efficiency (PCE) of 1.5% (±0.12) under 100 mW/cm² with a short-circuit current (J_sc)=5.73 mA/cm², a fill factor (FF)=0.45, and an open-circuit voltage (V_oc)=0.59 mV.     

Efficiency enhancement of polymer solar cells by incorporating a self-assembled layer of silver nanodisks

We report the efficiency enhancement of polymer solar cells by incorporating a silver nanodisks' self-assembled layer, which was grown on the indium tin oxide (ITO) surface by the electrostatic interaction between the silver particles and modified ITO. Polymer solar cells with a structure of ITO (with silver nanodisks)/poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) (Clevious P VP AI 4083)/poly(3-hexylthiophene):[6,6]-phenyl-C61 butyric acid methyl ester (P3HT:PC₆₁BM)/LiF/Al exhibited an open circuit voltage (V_OC) of 0.61±0.01 V, short-circuit current density (J_SC) of 9.24±0.09 mA/cm², a fill factor (FF) of 0.60±0.01, and power conversion efficiency (PCE) of 3.46±0.07% under one sun of simulated air mass 1.5 global (AM1.5G) irradiation (100 mW/cm²). The PCE was increased from 2.72±0.08% of the devices without silver nanodisks to 3.46±0.07%, mainly from the improved photocurrent density as a result of the excited localized surface plasmon resonance (LSPR) induced by the silver nanodisks.     

Nano-structured Cu2O solar cells fabricated on sparse ZnO nanorods

Nano-structured Cu₂O/ZnO nanorod (NR) heterojunction solar cells fabricated on indium tin oxide (ITO)-coated glass are studied. Substrate film and NR density have a strong influence on the preferred growth of the Cu₂O film. The X-ray diffractometer (XRD) analysis results show that highly (2 0 0)-preferred Cu₂O film was formed when plating on plain ITO substrate. However, a highly (1 1 1)-preferred Cu₂O film was obtained when plating on sparse ZnO NRs. SEM, TEM and XRD studies on sparse NR samples indicate that the Cu₂O nano-crystallites mostly initiate its nucleation on the peripheral surfaces of the ZnO NRs, and are also highly (1 1 1)-oriented. Solar cells with ZnO NRs yielded much higher efficiency than those without. In addition, ZnO NRs plated on a ZnO-coated ITO glass significantly improve the shunt resistance and open-circuit voltage (V_oc) of the devices, with consistently much higher efficiency obtained than when ZnO NRs are directly plated on ITO film. However, longer NRs do not improve the efficiency due to low short-circuit current (J_sc) and slightly higher series resistance. The best conversion efficiency of 0.56% was obtained from a Cu₂O/ZnO NRs heterojunction solar cell fabricated on a 80 nm ZnO-coated ITO glass with V_oc=0.514 V, J_sc=2.64 mA/cm² and 41.5% fill factor.     

High-performance polymer photovoltaic devices with inverted structure prepared by thermal lamination

Use of a lamination process for the introduction of Au electrode, instead of conventional metal evaporation, improved the power conversion efficiency (PCE) of inverted-structure photovoltaic devices from 1.6% to 2.6% based on a bulk heterojunction of poly(3-hexylthiophene) (P3HT) and (6,6)-phenyl C₆₁ butyric acid methyl ester (PCBM). X-ray photoelectron spectroscopy indicated that a thin layer of P3HT is spontaneously formed at the air/polymer blend layer interface during the spin-coating process. It is suggested that the vacuum-evaporated gold could destroy the surface-segregated thin layer of P3HT, while the lamination process preserves the surface structure working as an electron-blocking layer. The insertion of a PEDOT:PSS layer, between the metal electrode and polymer layer, in the lamination process further improved the PCE to 3.3% with a short-circuit current density of 9.94 mA cm⁻², an open-circuit voltage of 0.60 V, and a fill factor of 55% under AM1.5 100 mW cm⁻² irradiation.     

Water and oxygen induced degradation of small molecule organic solar cells

Small molecule organic solar cells were studied with respect to water and oxygen induced degradation by mapping the spatial distribution of reaction products in order to elucidate the degradation patterns and failure mechanisms. The active layers consist of a 30 nm bulk heterojunction formed by the donor material zinc-phthalocyanine (ZnPc) and the acceptor material Buckminsterfullerene (C₆₀) followed by 30 nm C₆₀ for additional absorption. The active layers are sandwiched between 6 nm 4,7-diphenyl-1,10-phenanthroline (Bphen) and 30 nm N,N′-diphenyl-N,N′-bis(3-methylphenyl)-[1,1′-biphenyl]-4,4′-diamine p-doped with C₆₀F₃₆ (MeO-TPD:C₆₀F₃₆), which acted as hole transporting layer. Indium-tin-oxide (ITO) and aluminum served as hole and electron collecting electrode, respectively. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) and X-ray photoelectron spectroscopy (XPS) in conjunction with isotopic labeling using H₂¹⁸O and ¹⁸O₂ provided information on where and to what extent the atmosphere had reacted with the device. A comparison was made between the use of a humid (oxygen free) atmosphere, a dry oxygen atmosphere, and a dry (oxygen free) nitrogen atmosphere during testing of devices that were kept in the dark and devices that were subjected to illumination under simulated sunlight. It was found that water significantly causes the device to degrade. The two most significant degradation mechanisms are diffusion of water through the aluminum electrode resulting in massive formation of aluminum oxide at the BPhen/Al interface, and diffusion of water into the ZnPc:C₆₀ layer where ZnPc becomes oxidized. Finally, diffusion from the electrodes was found to have no or a negligible effect on the device lifetime.     

Microcrystalline and micromorph device improvements through combined plasma and material characterization techniques

Hydrogenated microcrystalline silicon (μc-Si:H) growth by very high frequency plasma-enhanced chemical vapor deposition (VHF-PECVD) is studied in an industrial-type parallel plate KAI reactor. Combined plasma and material characterization techniques allow to assess critical deposition parameters for the fabrication of high quality material. A relation between low intrinsic stress of the deposited i-layer and better performing solar cell devices is identified. Significant solar cell device improvements were achieved based on these findings: high open circuit voltages above 520 mV and fill factors above 74% were obtained for 1 μm thick μc-Si:H single junction cells and a 1.2 cm² micromorph device with 12.3% initial (V_oc=1.33 V, FF=72.4%, J_sc=12.8 mA cm⁻²) and above 10.0% stabilized efficiencies.     

Ionic liquid electrolyte based on S-propyltetrahydrothiophenium iodide for dye-sensitized solar cells

A new ionic liquid S-propyltetrahydrothiophenium iodide (T₃I) was developed as the solvent and iodide ion source in electrolyte for dye-sensitized solar cells. The electrochemical behavior of the /I⁻ redox couple and effect of additives in this ionic liquid system was tested and the results showed that this ionic liquid electrolyte revealed good conducting abilities and potential application for solar devices. The effects of LiI and dark-current inhibitors were investigated. The dye-sensitized solar cell with the electrolyte (0.1 mol L⁻¹ LiI, 0.35 mol L⁻¹ I₂, 0.5 mol L⁻¹ NMBI in pure T₃I) gave short-circuit photocurrent density (J_sc) of 11.22 mA cm², open-circuit voltage (V_oc) of 0.61 V and fill factor (FF) of 0.51, corresponding to the photoelectric conversion efficiency (η) of 3.51% under one Sun (AM1.5).     

A study of vapor CdCl2 treatment by CSS in CdS/CdTe solar cells

We report the effect of CdCl₂ vapor treatment on the photovoltaic parameters of CdS/CdTe solar cells. Vapor treatment allows combining CdCl₂ exposure time and annealing in one step. In this alternative treatment, the CdS/CdTe substrates were treated with CdCl₂ vapor in a close spaced sublimation (CSS) configuration. The substrate temperature and CdCl₂ powder source temperature were 400 °C. The treatment was done by varying the treatment time (t) from 15 to 90 min. Such solar cells are examined by measuring their current density versus voltage (J-V) characteristics. The open-circuit voltage (V_oc), short circuit current density (J_sc) and fill factor (FF) of our best cell, fabricated and normalized to the area of 1 cm², were V_oc = 663 mV, J_sc = 18.5 mA/cm² and FF = 40%, respectively, corresponding to a total area conversion efficiency of η = 5%. In cells of minor area (0.1 cm²) efficiencies of 8% have been obtained.     

Enhancing the short-circuit current and efficiency of organic solar cells using MoO3 and CuPc as buffer layers

Efficient bulk-heterojunction (BHJ) (regioregular poly (3-hexylthiophene) (P3HT): (6, 6)-phenyl C₆₁ butyric acid methyl ester (PCBM)) solar cells were fabricated with molybdenum trioxide (MoO₃) and copper phthalocyanine (CuPc) as buffer layers. The insertion of MoO₃ layer was found to be critical to the device performance, effectively extracting holes to prevent the exciton quenching and reducing the interfacial resistance because of alignment of energy levels. The introduction of CuPc buffer layer was observed to be ameliorative for device performance, further enlarging the visible absorption spectra range of the devices. The effect of the MoO₃ and CuPc layer thickness on device performance was studied. The optimized thickness was achieved when MoO₃ layer was 12 nm and CuPc layer was 6 nm, resulting in optimized power conversion efficiency (PCE) of 3.76% under AM1.5G 100 mW/cm² illumination.