泡沫铝的制备及其力学行为的研究

简要介绍泡沫金属的性能特点、制备方法及其应用.采用加压渗流法制备具有开孔结构的泡沫铝,并对此分别进行准静态和动态压缩实验,研究其静态和动态压缩应变力-应变响应特征、应变率效应和吸能特性.实践证明这种泡沫铝具有很明显的应变率效应.     

梯度泡沫铝的制备及力学性能研究进展

梯度泡沫铝是一种具有多孔结构和高度可设计性的结构功能一体化材料。基于结构的特点,梯度泡沫铝在不同受力状态下具有独特的能量吸收行为,根据应用环境的需要可对其结构进行优化设计,因此梯度泡沫铝在减震吸能方面有巨大的潜能。结合国内外文献,概述了近些年有关梯度泡沫铝的制备及力学性能的主要研究进展。从固相法和液相法两方面介绍了梯度泡沫铝的主要制备方法,总结了梯度泡沫铝在准静态和动态压缩载荷下的力学响应,讨论了影响梯度泡沫铝吸能特性的因素。     

石膏型渗流法制备的开孔泡沫铝的压缩行为研究

本文采用可溶石膏型预制块,通过加压渗流的方法制备了泡沫纯铝、泡沫ZL101合金和泡沫ZL102合金,并通过准静态压缩实验研究了3种不同基体材料的泡沫铝的压缩行为及吸能性能.结果表明:通过石膏型渗流法制备的开孔泡沫铝合金的孔隙率可以达到85％～93.5％;泡沫铝基体材料的力学性能对泡沫铝压缩力学性能有重要影响;泡沫ZL1...     

合金化对泡沫铝压缩力学行为的影响

采用Si、Mg及Cu元素进行合金化处理，制备了几种不同力学性能的开孔泡沫铝，通过准静态压缩实验研究了合金化对泡沫铝压缩力学性能与吸能特征的影响。实验结果表明，Si、Mg及Cu元素合金化处理能显著改变泡沫铝的应力-应变行为与吸能特征，使泡沫铝的屈服强度提高，吸能性大幅度上升。     

泡沫铝层合圆管纵向和横向压缩力学性能研究

用碳化硅颗粒增强泡沫铝为夹芯,不锈钢圆管为面板制备层合圆管,研究了层合圆管在准静态压缩条件下的纵向和横向变形行为和能量吸收性能.研究表明,层合圆管的纵向压缩变形方式与空管相比发生了改变,由不对称变形模式变为轴对称变形模式;载荷-位移曲线平台段锯齿形波动与曲屈圈的形成呈现对应关系;层合圆管纵向和横向的吸能能力均远大于不锈钢圆管和泡沫铝吸收的能量之和,并且随着应变的增加,层合圆管的吸能能力增加更为快速;层合圆管在保持泡沫铝轻质的同时,在纵向和横向两个方向上均大幅度提高泡沫铝的吸能能力.     

泡沫铝填充方铝管的瞬态动力学分析

泡沫铝填充方铝管在高速冲击载荷作用下,由于应力波的传播和惯性效应等的作用,试件并非处于受力平衡的均匀应力状态,上下底面的受力会有很大的差别.采用LS - DYNA研究泡沫铝填充方铝管和泡沫铝柱在30m/s的匀速冲击载荷作用下的瞬态吸能和上下底面的冲量特性,并与准静态模型做比较.研究发现泡沫铝填充方铝管的吸能较准静态提高20.9％,上底面的冲量比下底面高10.4％,下底面的最大峰值力比准静态时仅升高8.8％.     

泡沫铝填充金属波纹板耦合增强机理研究

将闭孔泡沫铝填充到空心金属波纹板孔隙当中即可获得泡沫铝填充波纹板结构,对其准静态压缩吸能特性进行实验表征。研究表明,泡沫铝填充波纹板其压缩应力远高于泡沫铝与空心波纹板二者单独压缩应力之和,表现出明显的耦合增强效应,其单位质量峰值抗压缩强度及单位质量能量吸收率(SEA)可分别高达对应空心结构的6.3及14.8倍,即使和泡沫铝相比,其SEA仍可提高50%以上。进一步通过对空心波纹芯体结构的屈曲变形模式研究表明,泡沫铝的填充给予了波纹芯体单元足够强的横向支撑,使其变形模式转变为空心结构难以产生的更加高阶的屈曲变形模式,屈曲波长变短,产生耦合增强效应。     

泡沫铝合金显微组织和压缩力学性能的研究

采用Si、Mg及Cu元素进行合金化处理，制备了几种不同力学性能的开孔泡沫铝，并通过准静态压缩实验，研究合金化对泡沫铝压缩力学行为与吸能特征的影响。实验结果表明：采用Si、Mg及Cu元素合金化处理显著改变了泡沫铝的应力-应变行为与吸能特征，使泡沫铝的屈服强度提高，吸能性大幅度上升。另外，还研究了渗流法制备工艺对泡沫铝微观组织和性能的影响，结果显示由于渗流法制备过程特殊的凝固条件，使得泡沫铝的微观组织比相同成分的铸造铝合金的组织明显粗大。     

真空渗流法制备泡沫铝及其动态力学性能的研究

以真空渗流法制备陶瓷中空球泡沫铝,研究了应变率对吸能量和吸能效率的影响、相对密度对屈服强度的影响,并与普通泡沫铝进行比较。结果表明,工艺简单可行,所制备的泡沫铝的动态压缩应力-应变曲线只有弹性变形区和塑性变形区;随应变率的增大,屈服强度和吸能效率变化规律不明显,吸能量增大;随相对密度的增大,屈服强度增大,吸能量增大,吸能效率也增大;动态压缩时两种泡沫铝的吸能效率均较高,最大吸能效率大于0.9,是良好的吸能材料。     

泡沫铝表面Ni-W共沉积及性能研究

目的 进一步提高泡沫铝材料的强度及耐蚀特性,同时明确金属涂覆泡沫铝材料的综合耗能指标。方法 对泡沫铝表面预镀镍层后,在硫酸盐体系下,利用脉冲电镀进行镍钨合金共沉积。通过准静态压缩测试及扫描电镜分析,得到泡沫铝、预镀镍泡沫铝及镍钨共沉积泡沫铝材料的特征曲线及变形模式,综合分析材料的增强机理及综合耗能指标。采用电化学测试对比分析材料耐蚀特性。结果 泡沫铝表面共沉积镍钨合金层后,其峰值应力比镀镍泡沫铝平均提高了10%,较基体泡沫铝平均提高了约45%。强度提高来源于变形过程中包覆金属的支撑及铝基体-镍镀层界面处的拉伸撕裂。镍钨合金共沉积使泡沫铝的能量吸收增加38%,吸能效率有所提升,且其自腐蚀电位较镀镍泡沫铝及基体泡沫铝明显正移,腐蚀倾向及腐蚀速率降低。结论 泡沫铝表面镍钨合金共沉积使其强度、耐蚀性较镀镍泡沫铝进一步提高。由于特征曲线及变形模式的改变,镍钨共沉积泡沫铝的耗能特性提升明显。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

THERMODYNAMICS STUDY ON THE DECOMPOSITION OF CHROMITE WITH KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

INFLUENCE OF HEAT TREATMENT ON DAMPING BEHAVIOUR OF THE MAGNESIUM WROUGHT ALLOY AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.