Carbon-coated lithium titanate: effect of carbon precursor addition processes on the electrochemical performance

In this paper,two carbon-coated lithium titanate(LTO-C1 and LTO-C2)composites were synthesized using the ball-milling-assisted calcination method with different carbon precursor addition processes.The physical and electrochemical properties of the as-synthesized negative electrode materials were characterized to investigate the effects of two carbon-coated LTO synthesis processes on the electrochemical performance of LTO.The results show that the LTO-C2 synthesized by using Li2CO3 and TiO2 as the raw materials and sucrose as the carbon source in a one-pot method has less polarization during lithium insertion and extraction,minimal charge transfer impedance value and the best electrochemical performance among all samples.At the current density of 300 mA·h·g^-1,the LTO-C2 composite delivers a charge capacity of 126.9 mA·h·g^-1,and the reversible capacity after 300 cycles exceeds 121.3 mA·h·g^-1 in the voltage range of 1.0–3.0 V.Furthermore,the electrochemical impedance spectra show that LTO-C2 has higher electronic conductivity and lithium diffusion coefficient,which indicates the advantages in electrode kinetics over LTO and LTO-C1.The results clarify the best electrochemical properties of the carbon-coated LTO-C2 composite prepared by the one-pot method.     

One-step synthesis of recoverable CuCo2S4 anode material for high-performance Li-ion batteries

A facile one-step hydrothermal method has been adopted to directly synthesize the CuCo₂S₄ material on the surface of Ni foam. Due to the relatively large specific surface area and wide pore size distribution, the CuCo₂S₄ material not only effectively increases the reactive area, but also accommodates more side reaction products to avoid the difficulty of mass transfer. When evaluated as anode for Li-ion batteries, the CuCo₂S₄ material exhibits excellent electrochemical performance including high discharge capacity, outstanding cyclic stability and good rate performance. At the current density of 200 mA·g⁻¹, the CuCo₂S₄ material shows an extremely high initial discharge capacity of 2510 mAh·g⁻¹, and the cycle numbers of the material even reach 83 times when the discharge capacity is reduced to 500 mAh·g⁻¹. Furthermore, the discharge capacity can reach 269 mAh·g⁻¹ at a current of 2000 mA·g⁻¹. More importantly, when the current density comes back to 200 mA·g⁻¹, the discharge capacity could be recovered to 1436 mAh·g⁻¹, suggesting an excellent capacity recovery characteristics.     

Lithium Storage Performance of Hollow and Core/Shell TiO2 Microspheres Containing Carbon☆

TiO2 microspheres containing carbon have been synthesized viaa one-pot hydrothermal process using CTAB as the mesoporous template and nanoparticle stabilizer and Ti(SO4)2 and sucrose as titanium and ca...     

FeS2@TiO2 nanorods as high-performance anode for sodium ion battery

Sodium-ion battery (SIB) is an ideal device that could replace lithium-ion battery (LIB) in grid-scale energy storage system for power because of the low cost and rich reserve of raw material. The key challenge lies in developing electrode materials enabling reversible Na⁺ insertion/desertion and fast reaction kinetics. Herein, a core-shell structure, FeS₂ nanoparticles encapsulated in biphase TiO₂ shell (FeS₂@TiO₂), is developed towards the improvement of sodium storage. The diphase TiO₂ coating supplies abundant anatase/rutile interface and oxygen vacancies which will enhance the charge transfer, and avoid severe volume variation of FeS₂ caused by the Na⁺ insertion. The FeS₂ core will deliver high theoretical capacity through its conversion reaction mechanism. Consequently, the FeS₂@TiO₂ nanorods display notable performance as anode for SIBs including long-term cycling performance (637.8 mA·h·g^-1 at 0.2 A·g^-1 after 300 cycles, 374.9 mA·h·g^-1 at 5.0 A·g^-1 after 600 cycles) and outstanding rate capability (222.2 mA·h·g^-1 at 10 A·g^-1). Furthermore, the synthesized FeS₂@TiO₂ demonstrates significant pseudocapacitive behavior which accounts for 90.7% of the Na⁺ storage, and efficiently boosts the rate capability. This work provides a new pathway to fabricate anode material with an optimized structure and crystal phase for SIBs.     

Nickel(II) ion-intercalated MXene membranes for enhanced H2/CO2 separation

Hydrogen fuel has been embraced as a potential long-term solution to the growing demand for clean energy. A membrane-assisted separation is promising in producing high-purity H₂. Molecular sieving membranes (MSMs) are endowed with high gas selectivity and permeability because their well-defined micropores can facilitate molecular exclusion, diffusion, and adsorption. In this work, MXene nanosheets intercalated with Ni²⁺ were assembled to form an MSM supported on Al₂O₃ hollow fiber via a vacuum-assisted filtration and drying process. The prepared membranes showed excellent H₂/CO₂ mixture separation performance at room temperature. Separation factor reached 615 with a hydrogen permeance of 8.35 × 10⁻⁸ mol·m⁻²·s⁻¹·Pa⁻¹. Compared with the original Ti₃C₂T_x/Al₂O₃ hollow fiber membranes, the permeation of hydrogen through the Ni²⁺-Ti₃C₂T_x/Al₂O₃ membrane was considerably increased, stemming from the strong interaction between the negatively charged MXene nanosheets and Ni²⁺. The interlayer spacing of MSMs was tuned by Ni²⁺. During 200-hour testing, the resultant membrane maintained an excellent gas separation without any substantial performance decline. Our results indicate that the Ni²⁺ tailored Ti₃C₂T_x/Al₂O₃ hollow fiber membranes can inspire promising industrial applications.     

g-C3N4-coated MnO2 hollow nanorod cathode for stable aqueous Zn-ion batteries

Aqueous zinc-ion batteries are attracting considerable attention because of their high safety compared with conventional lithium-ion batteries. Manganese-based materials have been widely developed for zinc-ion batteries cathode owning to their low cost, high security and simple preparation. However, the severe volume expansion and poor stability during charging and discharging limit the further development of manganese-based cathodes. Herein, superior α-MnO₂@g-C₃N₄ was successfully prepared for stable zinc-ion batteries (ZIBs) cathode by introducing g-C₃N₄ nanosheets. Compared with pure α-MnO₂, α-MnO₂@g-C₃N₄ has a specific capacity of 298 mAh·g^–1 at 0.1 A·g^–1. Even at 1 A·g^–1, the α-MnO₂@g-C₃N₄ still retains 100 mAh·g^–1 (83.4% retention after 5000 cycles), implying its excellent cycling stability. The α-MnO₂@g-C₃N₄-based cathode has the highest energy density (563 Wh·kg^–1) and power energy density (2170 W·kg^–1). This work provides new avenues for the development of a wider range of cathode materials for ZIBs.     

The prior rules of designing Ti3C2Tx MXene-based gas sensors

Working temperature, sensitivity, and selectivity are some of the characteristics of the applied gas sensors. How to design and fabricate an ideal gas sensor working at room temperature is still challenging and attracting lots of interest. Two-dimensional (2D) materials with ultra-thin structure have been demonstrated as a family of ideal candidates to achieve this goal. Among them, Ti₃C₂T_x MXene, a kind of layered sheet synthesized by selectively etching MAX phases materials, shows remarkable potential to be the sensitive materials solely or in a composite. However, their designing rules are still lacking critical thinking from the viewpoint of the intrinsic property of Ti₃C₂T_x MXene based materials. In this article, two critical features, i.e., the thickness of the sensitive materials, and the scope of the analytes, are elaborated towards Ti₃C₂T_x MXene based gas sensors after characterizing the performance of sensing reducing gases (NH₃ and CO) and oxidizing gas (NO₂). First, the thinner the Ti₃C₂T_x MXene sensitive layer, the better the sensitivity. Second, the Ti₃C₂T_x MXene based gas sensor is not suitable for strong and moderate oxidation gas due to its ease of oxidation. These two rules are demonstrated, and could be considered with priority both in the future researches and practical applications.     

Facile synthesis of spinel LiNi0.5Mn1.5O4 as 5.0 V-class high-voltage cathode materials for Li-ion batteries

LiNi_0.5Mn_1.5O₄ and LiMn₂O₄ with novel spinel morphology were synthesized by a hydrothermal and post-calcination process. The synthesized LiMn₂O₄ particles (5-10 μm) are uniform hexahedron, while the LiNi_0.5Mn_1.5O₄ has spindle-like morphology with the long axis 10-15 μm, short axis 5-8 μm. Both LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ show high capacity when used as cathode materials for Li-ion batteries. In the voltage range of 2.5-5.5 V at room temperature, the LiNi_0.5Mn_1.5O₄ has a high discharge capacity of 135.04 mA·h·g^-1 at 20 mA·g^-1, which is close to 147 mA·h·g^-1 (theoretical capacity of LiNi_0.5Mn_1.5O₄). The discharge capacity of LiMn₂O₄ is 131.08 mA·h·g^-1 at 20 mA·g^-1. Moreover, the LiNi_0.5Mn_1.5O₄ shows a higher capacity retention (76%) compared to that of LiMn₂O₄ (61%) after 50 cycles. The morphology and structure of LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ are well kept even after cycling as demonstrated by SEM and XRD on cycled LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ electrodes.     

Decorating MXene with tiny ZIF-8 nanoparticles: An effective approach to construct composites for water pollutant removal

MXenes have attracted increasing research enthusiasm owing to their unique physical and chemical properties. Although MXenes exhibit exciting potential in cations adsorption due to their unique surface groups, the adsorption capacity is limited by the low specific surface area and undeveloped porosity. Our work aims at enhancing the adsorption performance of a well-known MXene, Ti₃C₂T_x, for methylene blue (MB) by decorating tiny ZIF-8 nanoparticles in the interlayer. After the incorporation of ZIF-8, suitable interspace in the layers resulting from the distribution of tiny ZIF-8 appears. When employing in MB, the adsorption capacity of composites can reach up to 107 mg·g^-1 while both ZIF-8 (3 mg·g^-1) and Ti₃C₂T_x (9 mg·g^-1) show nearly no adsorption capacity. The adsorption mechanism was explored, and the good adsorption capacity is caused by the synergistic effect of ZIF-8 and Ti₃C₂T_x, for neither of them is of suitable interspace or surface groups for MB adsorption. Our work might pave the way for constructing functional materials based on the introduction of nanoparticles into layered materials for various adsorption applications.     

Effective enhancement of the electrochemical properties for Na2FeP2O7/C cathode materials by boron doping

In recent years, the composite materials based on polyanionic frameworks as secondary sodium ion battery electrode material have been developed in large-scale energy storage applications due to its safety and stability. The Na₂FeP₂O₇/C (theoretical capacity 97 mA·h·g^-1) is recognized as optimum Na-storage cathode materials with a trade-off between electrode performance and cost. In the present work, The Na₂FeP₂O₇/C and boron-doped Na₂FeP_2-BO₇/C composites were synthesized via a novel method of liquid phase combined with high temperature solid phase. The non-metallic element B doping not only had positive influence on the crystal structure stability, Na⁺ diffusion and electrical conductivity of Na₂FeP₂O₇/C, but also contributed to the high-value recycling of B element in waste borax. The structure and electrochemical properties of the cathode material were investigated via X-ray diffraction (XRD), scanning electron microscopy (SEM), The X-ray photoelectron spectroscopy (XPS), electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and charge/discharge cycling. The results showed that different amounts of boron doping had positive effects on the structure and electrochemical properties of the material. The initial charge/discharge performances of born doped materials were improved in comparison to the bare Na₂FeP₂O₇/C. The cycle performance of the Na₂FeP_1.95B_0.05O₇/C showed an initial reversible capacity of 74.8 mA·h·g^-1 and the high capacity retention of 91.8% after 100 cycles at 1.0 C, while the initial reversible capacity of the bare Na₂FeP₂O₇/C was only 66.2 mA·h·g^-1. The improvement of apparent Na⁺ diffusion and electrical conductivity due to B doping were verified by the EIS test and CVs at various scan rate. The experimental results from present work is useful for opening new insight into the contrivance and creation of applicable sodium polyanionic cathode materials for high-performance.     

Pre-sodiation strategy for superior sodium storage batteries

The irreversible consumption of sodium in the initial several cycles greatly led to the attenuation of capacity, which caused the low initial coulombic efficiency (ICE) and obvious poor cycle stability. Pre-sodiation can effectively improve the electrochemical performance by compensating the capacity loss in the initial cycle. Here, carbon-coated sodium-pretreated iron disulfide (NaFeS₂@C) has been synthesized through conventional chemical method and used in sodium metal battery as a cathode material. The calculated density of states (DOS) of NaFeS₂@C is higher, which implies enhanced electron mobility and improved cycle reversibility. Because of the highly reversible conversion reaction and the compensation of irreversible capacity loss during the initial cycle, the Na/NaFeS₂@C battery achieves ultra-high initial coulombic efficiency (96.7%) and remarkable capacity (751 mA·h·g^-1 at 0.1 A·g^-1). In addition, highly reversible electrochemical reactions and ultra-thin NaF-rich solid electrolyte interphase (SEI) also benefit for the electrochemical performance, even at high current density of 100 A·g^-1, it still exhibits a reversible capacity of 136 mA·h·g^-1, and 343 mA·h·g^-1 after 2500 cycles at 5.0 A·g^-1. This work aims to bring up new insights to improve the ICE and stability of sodium metal batteries.     

响应面法优化碳热还原合成LiFePO4/C的工艺参数（英文）

A statistically based optimization strategy is used to optimize the carbothermal reduction technology for the synthesis of LiFePO4/C using LiOH,FePO4 and sucrose as raw materials.The experimental data for fitting the response are collected by the central composite rotatable design(CCD).A second order model for the discharge ca-pacity of LiFePO4/C is expressed as a function of sintering temperature,sintering time and carbon content.The ef-fects of individual variables and their interactions are studied by a statistical analysis(ANOVA).The results show that the linear effects and the quadratic effects of sintering temperature,carbon content and the interactions among these variables are statistically significant,while those effects of sintering time are insignificant.Response surface plots for spatial representation of the model illustrate that the discharge capacity depends on sintering temperature and carbon content more than sintering time.The model obtained gives the optimized reaction parameters of sinter-ing temperature at 652.0 ℃,carbon content of 34.33 g?mol-1 and 8.48 h sintering time,corresponding to a dis-charge capacity of 150.8 mA·h·g-1.The confirmatory test with these optimum parameters gives the discharge ca-pacity of 147.2 and 105.1 mA·h·g-1 at 0.5 and 5 C,respectively.     

锂离子电池负极材料Li4Ti5O12/C的制备与表征

针对Li₄Ti₅O₁₂导电性和倍率性能差的缺陷,以PEG为碳源采用溶胶-凝胶法制备出电池负极材料Li₄Ti₅O₁₂/C,考察不同分子量聚乙二醇PEG(400、600、1000)做碳源制备的Li₄Ti₅O₁₂/C复合材料电化学性能的优劣,采用热重分析仪(TG)、X射线衍射仪(XRD)、扫描电镜(SEM)、透射电镜(TEM)、恒流充放电、倍率放电、交流阻抗(EIS)等方法对材料进行了结构表征和电化学性能测试。结果表明:以PEG1000为碳源时得到的Li₄Ti₅O₁₂/C,0.1C下首次放电比容量为143.5 mA·h·g^-1,2C的倍率下仍然保持了105 mA·h·g^-1的比容量,容量保持率达到73.17%,并且此材料有最小的电阻,在大电流条件下有良好的电化学性能。     

原位合成的介孔TiO2-B/锐钛微粒:改善的锂离子电池阳极材料（英文）

Mesoporous TiO2-B/anatase microparticles have been in-situ synthesized from K2Ti2O5 without template. The TiO2-B phase around the particle surface accelerates the diffusion of charges through the interface, while the anatase phase in the core maintains the capacity stability. The heterojunction interface between the main polymorph of anatase and the trace of TiO2-B exhibits promising lithium ion battery performance. This trace of 5%(by mass) TiO2-B determined by Raman spectra brings the first discharge capacity of this material to 247 mA·h·g?1, giving 20%improvement com-pared to the anatase counterpart. Stability testing at 1 C reveals that the capacity maintains at 171 mA·h·g?1, which is better than 162 mA·h·g?1 for single phase anatase or 159 mA·h·g?1 for TiO2-B. The mesoporous TiO2-B/anatase microparticles also show superior rate performance with 100 mA·h·g?1 at 40 C, increased by nearly 25%as compared to pure anatase. This opens a possibility of a general design route, which can be applied to other metal oxide electrode materials for rechargeable batteries and supercapacitors.     

Novel hierarchical yolk-shell α-Ni(OH)2/Mn2O3 microspheres as high specific capacitance electrode materials for supercapacitors

For high performance supercapacitors, novel hierarchical yolk-shell a-Ni(OH)₂/Mn₂O₃ microspheres were controllably synthesized using a facile two-step method based on the solvothermal treatment. The unique a-Ni(OH)₂ based yolk-shell microstructures decorated with numerous interconnected nanosheets and the hetero-composition features can synergistically enhance reactive site exposure and electron conduction within the microspheres, facilitate charge transfer between electrolyte and electrode materials, and release structural stress during OH⁻ chemisorption/desorption. Moreover, the Mn₂O₃ sediments distributed over the a-Ni(OH)₂ microspheres can serve as an effective protective layer for electrochemical reactions. Consequently, when tested in 1 mol·L⁻¹ KOH aqueous electrolyte for supercapacitors, the yolk-shell a-Ni(OH)₂/Mn₂O₃ microspheres exhibited a considerably high specific capacitance of 2228.6 F·g⁻¹ at 1 A·g⁻¹ and an impressive capacitance retention of 77.7% after 3000 cycles at 10 A·g⁻¹. The proposed a-Ni(OH)₂/Mn₂O₃ microspheres with hetero-composition and unique hierarchical yolk-shell microstructures are highly promising to be used as electrode materials in supercapacitors and other energy storage devices.     

Self-assembled MoS2/C nanoflowers with expanded interlayer spacing as a high-performance anode for sodium ion batteries

Two-dimensional (2D) MoS₂ nanomaterials have been extensively studied due to their special structure and high theoretical capacity, but it is still a huge challenge to improve its cycle stability and achieve superior fast charge and discharge performance. Herein, a facile one-step hydrothermal method is proposed to synthetize an ordered and self-assembled MoS₂ nanoflower (MoS₂/C NF) with expanded interlayer spacing via embedding a carbon layer into the interlayer. The carbon layer in the MoS₂ interlayer can speed the transfer of electrons, while the nanoflower structure promotes the ions transport and improves the structural stability during the charging/discharging process. Therefore, MoS₂/C NF electrode exhibits exceptional rate performance (318.2 and 302.3 mA·h·g^-1 at 5.0 and 10.0 A·g^-1, respectively) and extraordinary cycle durability (98.8% retention after 300 cycles at a current density of 1.0 A·g^-1). This work provides a simple and feasible method for constructing high-performance anode composites for sodium ion batteries with excellent cycle durability and fast charge/discharge ability.     

Hybrid CuO-Co3O4 nanosphere/RGO sandwiched composites as anode materials for lithium-ion batteries

Hybrid CuO-Co₃O₄ nanosphere building blocks have been embedded between the layered nanosheets of reduced graphene oxides with a three dimensional (3D) hybrid architecture (CuO-Co₃O₄-RGO), which are successfully applied as enhanced anodes for lithium-ion batteries (LIBs). The CuO-Co₃O₄-RGO sandwiched nanostructures exhibit a reversible capacity of~847 mA·h·g^-1 after 200 cycles' cycling at 100 mA·g^-1 with a capacity retention of 79%. The CuO-Co₃O₄-RGO compounds show superior electrochemical properties than the comparative CuO-Co₃O₄, Co₃O₄ and CuO anodes, which may be ascribed to the following reasons:the hybridizing multicomponent can probably give the complementary advantages; the mutual benefit of uniformly distributing nanospheres across the layered RGO nanosheets can avoid the agglomeration of both the RGO nanosheets and the CuO-Co₃O₄ nanospheres; the 3D storage structure as well as the graphene wrapped composite could enhance the electrical conductivity and reduce volume expansion effect associated with the discharge-charge process.     

Electrospun porous carbon nanofibers derived from bio-based phenolic resins as free-standing electrodes for high-performance supercapacitors

Phenolic resins were employed to prepare electrospun porous carbon nanofibers with a high specific surface area as free-standing electrodes for high-performance supercapacitors. However, the sustainable development of conventional phenolic resin has been challenged by petroleum-based phenol and formaldehyde. Lignin with abundant phenolic hydroxyl groups is the main non-petroleum resource that can provide renewable aromatic compounds. Hence, lignin, phenol, and furfural were used to synthesize bio-based phenolic resins, and the activated carbon nanofibers were obtained by electrospinning and one-step carbonization activation. Fourier transform infrared and differential scanning calorimetry were used to characterize the structural and thermal properties. The results reveal that the apparent activation energy of the curing reaction is 89.21 kJ·mol^–1 and the reaction order is 0.78. The activated carbon nanofibers show a uniform diameter, specific surface area up to 1100 m²·g^–1, and total pore volume of 0.62 cm³·g^–1. The electrode demonstrates a specific capacitance of 238 F·g^–1 (0.1 A·g^–1) and good rate capability. The symmetric supercapacitor yields a high energy density of 26.39 W·h·kg^–1 at 100 W·kg^–1 and an excellent capacitance retention of 98% after 10000 cycles. These results confirm that the activated carbon nanofiber from bio-based phenolic resins can be applied as electrode material for high-performance supercapacitors.     

Efficient CO2 adsorption and mechanism on nitrogen-doped porous carbons

In this work, nitrogen-doped porous carbons (NACs) were fabricated as an adsorbent by urea modification and KOH activation. The CO₂ adsorption mechanism for the NACs was then explored. The NACs are found to present a large specific surface area (1920.72– 3078.99 m²·g⁻¹) and high micropore percentage (61.60%–76.23%). Under a pressure of 1 bar, sample NAC-650-650 shows the highest CO₂ adsorption capacity up to 5.96 and 3.92 mmol·g⁻¹ at 0 and 25 °C, respectively. In addition, the CO₂/N₂ selectivity of NAC-650-650 is 79.93, much higher than the value of 49.77 obtained for the nonnitrogen-doped carbon AC-650-650. The CO₂ adsorption capacity of the NAC-650-650 sample maintains over 97% after ten cycles. Analysis of the results show that the CO₂ capacity of the NACs has a linear correlation (R² = 0.9633) with the cumulative pore volume for a pore size less than 1.02 nm. The presence of nitrogen and oxygen enhances the CO₂/N₂ selectivity, and pyrrole-N and hydroxy groups contribute more to the CO₂ adsorption. In situ Fourier transform infrared spectra analysis indicates that CO₂ is adsorbed onto the NACs as a gas. Furthermore, the physical adsorption mechanism is confirmed by adsorption kinetic models and the isosteric heat, and it is found to be controlled by CO₂ diffusion. The CO₂ adsorption kinetics for NACs at room temperature and in pure CO₂ is in accordance with the pseudo-first-order model and Avramís fractional-order kinetic model.     

Efficient MgO-doped CaO sorbent pellets for high temperature CO2 capture

Novel MgO-doped CaO sorbent pellets were prepared by gel-casting and wet impregnation. The effect of Na⁺ and MgO on the structure and CO₂ adsorption performance of CaO sorbent pellets was elucidated. MgO-doped CaO sorbent pellets with the diameter range of 0.5-1.5 mm exhibited an excellent capacity for CO₂ adsorption and adsorption rate due to the homogeneous dispersion of MgO in the sorbent pellets and its effects on the physical structure of sorbents. The results show that MgO can effectively inhibit the sintering of CaO and retain the adsorption capacity of sorbents during multiple adsorption-desorption cycles. The presence of mesopores and macropores resulted in appreciable change of volume from CaO (16.7 cm³∙mol⁻¹) to CaCO₃ (36.9 cm³∙mol⁻¹) over repeated operation cycles. Ca2Mg1 sorbent pellets exhibited favorable CO₂ capture capacity (9.49 mmol∙g⁻¹), average adsorption rate (0.32 mmol∙g⁻¹∙min⁻¹) and conversion rate of CaO (74.83%) after 30 cycles.