An impedance-matching technique for increasing the bandwidth ofmicrostrip antennas

The nature of the inherent narrow bandwidth of conventional microstrip patch antennas is considered. It is observed that, except for single-feed circularly polarized elements, their bandwidth is limited only by the resonant behavior of the input impedance and not by radiation pattern or gain variations, which usually are negligible over a moderate 10 to 20% bandwidth. Therefore, broadband impedance matching is proposed as a natural to increase the bandwidth. The maximum obtainable bandwidth is calculated using Fano's broadband matching theory. It is found that by using an optimally designed impedance-matching network, the bandwidth can be increased by a factor of at least 3.9, the exact value depending on the degree of matching required. A transmission-line prototype for a proper matching network is developed. The translation of this prototype network into a practical structure (e.g. a microstrip or stripline circuit) is considered. Practical design examples and experimental results which clearly show the validity of the technique are given     

Wide-band slot antennas with CPW feed lines: hybrid and log-periodic designs

In microwave and millimeter wave applications, slot antennas fed by coplanar waveguide (CPW) lines are receiving increasing attention. These antennas have several useful properties, such as a wider impedance bandwidth compared to microstrip patch antennas, and easier integration of solid-state active devices. In this paper novel CPW-fed wideband slot antennas are presented. The design procedure of CPW-fed hybrid slot antennas (HSA) having impedance bandwidths (VSWR<2) up to 57% is described. Theoretical and measured results are shown. We also describe the design procedure of a CPW-fed log-periodic slot antenna (LPSA). The impedance matching and the radiation characteristics of these structures were studied using a method of moment technique. Simulated and measured results for different dielectrics are presented.     

An enhanced bandwidth design technique for electromagneticallycoupled microstrip antennas

This paper describes a method of enhancing the bandwidth of two different electromagnetically coupled microstrip antennas by utilization of a tuning stub. An approximate theory and equations are developed to demonstrate the potential bandwidth improvement and required stub impedance characteristics. A novel dual-stub design is presented that achieves better characteristics than a conventional quarter wavelength open-end stub. As examples, the bandwidth (VSWR<2) of a conventional proximity-coupled microstrip antenna is increased from 4.8 to 8.4% and the bandwidth of a stacked aperture-coupled microstrip antenna is increased from 27.5 to 34.5% using this technique     

基于新型输出结构的宽带高效率功率放大器

提出一种具有新型匹配网络的宽带高效率功率放大器,以及利用开路扇形微带线构成的紧凑型输出匹配网络,并给出了阻抗推导过程。该输出匹配网络在一定带宽条件下能满足晶体管的高效率所对应的阻抗设计空间要求。为了进一步拓展带宽,采用阶跃式阻抗匹配方法设计输入匹配网络。通过理论分析与仿真,最后设计并制作了一款频段为1~3.1 GHz的宽带高效率J类功率放大器。测试结果表明,在该频段内漏极效率为61.4%~70.2%,输出功率为39.3~41.7 dBm,增益为9.3~11.7 dB。     

Investigation of a Compensated Rectangular Microstrip Antenna With Negative Capacitor and Negative Inductor for Bandwidth Enhancement

New broadband impedance matching circuits used to increase the impedance bandwidth of the microstrip antennas for transmit applications are proposed and analyzed. A microstrip patch operating at 10.5 GHz having 12.2% bandwidth has been utilized as a reference antenna. The impedance bandwidth of the antenna has been enhanced by using negative capacitance and inductance compensation networks from 12.22% to 16.96% and 24.50%, respectively. In addition, it has been shown that the active compensation significantly improves the radiation pattern     

Design and Experiment on Differentially-Driven Microstrip Antennas

Design and experiment is given of differentially-driven microstrip antennas. First, the design formulas to determine the patch dimensions and the location of the feed point for single-ended microstrip antennas are examined to design differentially-driven microstrip antennas. It is found that the patch length can still be designed using the formulas for the required resonant frequency but the patch width calculated by the formula usually needs to be widen to ensure the excitation of the fundamental mode using the probe feeds. The condition that links the patch width, the locations of the probe feeds, and the excitation of the fundamental mode is given. Second, the wideband techniques for single-ended microstrip antennas are evaluated for differentially-driven microstrip antennas. A novel H-slot is proposed for differentially-driven microstrip antennas to improve impedance bandwidth. Third, the effects of imperfect differential signal conditions on the performance of differentially-driven microstrip antennas are investigated for the first time. It is found that they only degrade the polarization purity in the -plane with an increased radiation of cross-polarization. Finally, both differentially-driven and single-ended microstrip antennas were fabricated and measured. It is shown that the simulated and measured results are in acceptable agreement. More importantly, it is also shown that the differentially-driven microstrip antenna has wider impedance bandwidth of measured 4.1% and simulated 3.9% and higher gain of measured 4.2 dBi and simulated 3.7 dBi as compared with those of measured 1.9% and simulated 1.3% and gain of measured 1.2 dBi and simulated 1.2 dBi of the single-ended microstrip antenna.     

Broadband conical microstrip antenna

Conical patch antennas, excited on TE11-mode are studied and their resonance frequencies are computed. These antennas present a broader bandwidth compared to classical microstrip antennas and, furthermore, good impedance matching can be easily obtained.     

A method for designing broad-band microstrip antennas inmultilayered planar structures

The narrow bandwidth of a microstrip antenna is one of the important features that restrict its wide usage. A simple and practical method for the design of broad-band microstrip antennas is presented in this paper. Utilizing this design technique, several two-layer microstrip antennas have been proposed. To confirm the applicability of the method for the designs of antennas at L-band, experiments have been carried out. The measured results show that the proposed antennas have a bandwidth of up to 25.7%. Also, the method proposed in this paper is applicable to the design of other types of multilayered planar antennas     

Broad-band gap coupled microstrip antenna

A microstrip antenna with large bandwidth is developed using a parasitic technique. Compared to the available wideband antennas, the proposed antenna structure is very compact and gives a less distorted radiation pattern with frequency. An impedance bandwidth eight times that of a conventional patch antenna of the same size is achieved. The concept of coupled microstrip line model is extended for theoretical interpretation of the impedance loci. The experimental procedure and results are described, and a theoretical analysis is presented     

Analysis of circularly polarized square ring and crossed-strip microstrip antennas

Segmentation technique coupled with cavity model have been used to analyze square ring and crossed-strip microstrip patch antennas for circular polarization. This technique is found to predict the characteristics of antennas correctly, as is evident from the close agreement between the calculated and measured results for resonant frequency, input impedance, radiation patterns, and bandwidth. Square ring antenna has been found to have larger impedance bandwidth and axial ratio bandwidth because of lowerQ. Crossed-strip antenna has larger size and thus fabrication tolerances can be relaxed.     

Bandwidth enhancement of inset-microstrip-line-fedequilateral-triangular microstrip antenna

By embedding a pair of properly-bent narrow slots in an equilateral-triangular microstrip patch, broadband operation of microstrip antennas with an inset microstrip-line feed can be achieved. With the proposed antenna design, the impedance bandwidth can be as large as ~3.0 times that of a corresponding simple triangular microstrip antenna. Some simple design rules for the proposed antenna have also been determined experimentally. The design rules and experimental results are presented and discussed     

Radiation and scattering characteristics of microstrip antennas onnormally biased ferrite substrates

Radiation and scattering characteristics of microstrip antennas and arrays printed on ferrite substrates with a normal magnetic bias field are described. The extra degree of freedom offered by the biased ferrite can be used to obtain a number of novel characteristics, including switchable and tunable circularly polarized radiation from a microstrip antenna having a single feed point, dynamic wide-angle impedance matching for phased arrays of microstrip antennas, and a switchable radar cross section reduction technique for microstrip antennas. Results are obtained from full-wave moment method solutions for single microstrip antennas and infinite arrays of microstrip antennas. A cavity model solution for a circular patch antenna on a biased ferrite substrate is also presented, to aid in understanding the operation of these antennas     

小型化缝隙加载圆极化及宽带微带贴片天线设计

提出了一种十字形缝隙加载的小型宽带及圆极化微带贴片天线的设计方法。该天线通过在方形贴片上加载一个大尺寸的十字形缝隙实现天线的尺寸缩减,介质基片采用由FR4和空气层组成的层叠结构,在缝隙中嵌入L型枝节,只需通过调整枝节上同轴线馈电点的位置来获得圆极化或宽带阻抗匹配。ANSYS HFSS仿真分析表明,天线的圆极化带宽（AR≤3 dB）为1.7%,阻抗带宽（VSWR≤2）为5.8%,天线在宽带范围内具有稳定的增益,峰值增益为7.8 dB,同时贴片面积缩减了52.3%。改变馈电点的位置可调节两个谐振频率使天线阻抗带宽达到9.4%,比传统的微带贴片天线阻抗带宽提高了114%。     

一种新型布局的圆极化微带天线阵优化设计

提出了一款高增益低副瓣新型圆极化微带天线阵。单元天线采用叠层切角圆极化微带结构,通过八边形边界布局和顺序旋转交叠组阵技术,实现了天线阵方向性图的对称性和圆极化辐射性能的最优化;馈电网络采用威尔金森功分器和最大平坦式阻抗变换器实现不等功分宽带阻抗匹配,通过改进馈电方向寻求对称结构,简化了馈电网络的设计。制作了天线阵实物并进行了测量。测试结果表明:天线在3.2~4.6 GHz频段内S₁₁<-10 dB,阻抗相对带宽36%;在3.8~4.5 GHz频段内顶点轴比小于3 dB,圆极化相对带宽17%;在4~4.4 GHz频段内天线增益均在15 dB以上,最高增益达17 dB。     

A modified contour Integral analysis for Sierpinski fractal carpet antennas with and without electromagnetic band gap ground plane

A modified contour integral method coupled with segmentation method has been used, for the first time, to analyze both the Sierpinski fractal carpet (SFC) antennas of different orders and an SFC antenna with electromagnetic band gap (EBG) ground plane. The close agreement between the calculated and measured results for resonant frequencies and input return losses indicates that this technique can be used to accurately predict the impedance characteristic. A novel stacked microstrip Sierpinski carpet fractal antenna using the EBG ground plane is also presented. Comparing to an ordinary microstrip fractal antenna, which has a maximum bandwidth of approximately 2%, the proposed antenna has a higher input impedance bandwidth of nearly 9%. The radiation patterns of the proposed antenna are improved due to the removal of unwanted radiation caused by the surface wave. The experimental measurement results of the proposed antenna are presented in this paper.     

Theoretical and experimental investigations on microstrip active array antennas and power combiners

In this paper, microstrip active array antennas and power combiners are investigated. The mutual impedance of a rectangular microstrip patch array is analyzed based on the Richmond's reaction integral equation and Galerkin technique in spectral-domain. The computer-aided analysis and design of the active array are then carried out by coupling the mutual impedances to the large-signal characteristics of Gunn diodes with a harmonic balance technique. Based on the theoretical study, microstrip active patch array antennas are investigated experimentally.     

并发双波段可重构功率放大器仿真设计

采用分布式PIN开关和并发双波段阻抗变换网络,实现了一种可重构高效率多波段功率放大器。与其他可重构放大器相比,该功率放大器降低了输出匹配电路的设计复杂度和开关对匹配电路的影响,有效节约了频谱资源,电路结构简单。双扇形开路微带线的使用拓展了高输入阻抗偏置电路的带宽。在进行匹配电路设计时,考虑了晶体管的寄生参数。仿真结果表明,该功率放大器具有高输出效率和良好的增益平坦度,验证了该方案的可行性。     

Active Integrated Antenna Design Using a Contact-Less, Proximity Coupled, Differentially Fed Technique

A novel contact-less, differential feeding technique suitable for integrated active antenna design is demonstrated. This technique utilizes an odd mode signal to generate fringing fields on either side of a microstrip gap under the antenna. This allows electromagnetic energy to be efficiently coupled from the transmission lines to the radiating antenna. In a balanced integrated antenna amplifier configuration, the proposed non-contact feeding method removes the need for any balun or power combining network. Hence in theory, a compact RF front-end design with lower losses can be realized. This feeding method has been successfully applied to the design of simple passive microstrip patch antennas and active integrated antennas (AIA). Simulated and measured results are also included to validate the proposed feeding concept and antenna designs. The performance of the proposed differential feeding technique on a simple microstrip patch antenna has been systematically studied. The study suggests that the proposed proximity method is broadband in nature, allowing antennas operating at different resonant frequencies to be swapped without the need to change the feed dimensions and without degrading the matching performance     

Méthodes d’analyse et de synthèse de quelques “ microantennes” à large bande en mode quasi transversal électromagnétique

The transmission line model has been utilized to determine the input impedance, the bandwidth, the radiation patterns and the mutual impedance of several microstrip antennas such as the arbitrary shape patch antennas and the wideband flat dipole which is an hybrid radiating source. We suppose that the dominant mode of propagation is the quasiTem one having negligible variation of fields in the transverse direction. Nevertheless a general scattering problem of an arbitrary shaped tridimensional antenna solved by moments method and the finite difference approach applied to integral equations has explained the very large bandwidth microstrip antenna behaviour. The wideband flat dipole has been used in flat arrays, with more than several hundred of such elements, and in microstrip phased arrays with beam steering in a large angular sector.     

Compact Chip-Resistor Loaded Active Integrated Patch Antenna for ISM Band Applications

As technology is moving towards miniature structures, demand for designing efficient compact antennas is increasing simultaneously. So it would be valuable to improve the features of small antennas, such as bandwidth and gain. A compact chip-resistor loaded microstrip antenna at 2.48 GHz frequency for industrial scientific and medical (ISM) band, with dimensions of 10 × 10 mm² is presented in this paper. With a novel geometry design, antenna is promoted to an active integrated antenna (AIA) on a two-layer printed circuit board (PCB), which contains passive antenna and active circuitry with a common ground plane. A monolithic amplifier is used to have an improvement around 10 dB in antenna gain. The impedance bandwidth has been increased during chip-resistor loading and adding active circuitry processes. For chip-resistor loaded antenna, that is 5.7 and 9.48% in simulation and measurement respectively. Moreover, the active integrated antenna has the measured impedance bandwidth of 58.7%. Since the low gain and narrow bandwidth of compact microstrip antennas might be a challenge for their operation, by compensating these drawbacks, proposed antenna would become more practical for special medical diagnostic applications, where doctors need stronger signals for monitoring.