High Polymer Content 3,5‐Pyridine‐Polybenzimidazole Copolymer Membranes with Improved Compressive Properties

Three series of polybenzimidazole (PBI) copolymers (3,5‐pyridine‐r‐2OH‐PBI, 3,5‐pyridine‐r‐para‐PBI, and 3,5‐pyridine‐r‐meta‐PBI) were polymerized and cast into membranes by the polyphosphoric acid (PPA) process. Monomer pairs with high and low solubility characteristics were used to define phase stability‐processing windows for preparing membranes with high temperature membrane gel stability. Creep compliance of these membranes (measured in compression at 180 °C) generally decreased with increasing polymer content. Membrane proton conductivities decreased linearly with increasing membrane polymer content. Fuel cell performances of some high‐solids 3,5‐pyridine‐based copolymer membranes (up to 0.66 V at 0.2 A cm^–2 following break‐in) were comparable to para‐PBI (0.68 V at 0.2 A cm^–2) despite lower phosphoric acid (PA) loadings in the high solids membranes. Long‐term steady‐state fuel cell studies showed 3,5‐pyridine‐r‐para‐PBI copolymers maintained a consistent fuel cell voltage of >0.6 V at 0.2 A cm^–2 for over 2,300 h. Phosphoric acid that was continuously collected from the long‐term study demonstrated that acid loss is not a significant mode of degradation for these membranes. The PBI copolymer membranes' reduced high‐temperature creep and long‐term operational stability suggests that they are excellent candidates for use in extended lifetime electrochemical applications.     

High Polymer Content 2,5‐Pyridine‐Polybenzimidazole Copolymer Membranes with Improved Compressive Properties

Three series of polybenzimidazole (PBI) random copolymers (2,5‐pyridine‐r‐meta‐PBI, 2,5‐pyridine‐r‐para‐PBI, and 2,5‐pyridine‐r‐2OH‐PBI) were synthesized and cast into phosphoric acid (PA) doped membranes using the PolyPhosphoric Acid (PPA) Process. Copolymer composition was adjusted using co‐monomers that impart high and low solubility characteristics to simultaneously control overall copolymer solubility and gel membrane stability. Measured under a static compressive force at 180 °C, copolymer membranes generally exhibited decreased creep compliance with increasing polymer content. Within each series of copolymer membranes, increasing polymer contents proportionally reduced the phosphoric acid/polymer repeat unit (PA/PRU) ratios and their respective proton conductivities. Some copolymer membranes exhibited comparable fuel cell performances (up to 0.66 V at 0.2 A cm⁻² following break‐in) to para‐PBI (0.68 V at 0.2 A cm⁻²) and equal to 3,5‐pyridine‐based high solids membranes. Furthermore, 2,5‐pyridine copolymer membranes maintained a consistent fuel cell voltage of >0.6 V at 0.2 A cm⁻² for over 8600 h under steady‐state operation conditions. Phosphoric acid loss was monitored during long‐term studies and demonstrated acid losses as low as 5.55 ng cm⁻² h⁻¹. The high‐temperature creep resistance and long‐term operational stabilities of the 2,5‐pyridine copolymer membranes suggest that they are excellent candidates for use in extended lifetime electrochemical applications.     

Synthesis and Properties of Random Copolymers of Functionalised Polybenzimidazoles for High Temperature Fuel Cells

A series of polybenzimidazoles (PBIs) incorporating main chain sulphonic acid groups were synthesised as random copolymers with p‐PBI in varying ratios using polyphosphoric acid (PPA) as both the polymerisation solvent and polycondensation reagent. The PPA process was used to produce high molecular weight phosphoric acid (PA) doped PBI gel membranes in a one‐step procedure. These membranes exhibit excellent mechanical properties (0.528–2.51 MPa tensile stress and 130–300% tensile strain) even at high acid doping levels [20–40 mol PA/PRU (polymer repeat unit)] and high conductivities (0.148–0.291 S cm^–1) at elevated temperatures (>100 °C) with no external humidification, depending on copolymer composition. Fuel cell testing was conducted with hydrogen fuel and air or oxygen oxidants for all membrane compositions at temperatures greater than 100 °C without external feed gas humidification. Initial studies showed a maximum fuel performance of 0.675 V for the 25 mol% s‐PBI/75 mol% p‐PBI random copolymer at 180 °C and 0.2 A cm^–2 with hydrogen and air, and 0.747 V for the same copolymer at 180 °C and 0.2 A cm^–2 with hydrogen and oxygen.     

Synthesis of aromatic poly(amide-imide) copolymers containing para–meta benzoic structure

Thermostable poly(amide-imide)s containing para–meta benzoic structure were synthesized by reacting a para–meta benzoic polyamide prepolymer with various diisocyanate-terminated polyimide prepolymers. The polyamide prepolymers were prepared by first reacting m-phenylene diamine and isophthaloyl dichloride to form a poly(m-phenylphthalamide) prepolymer, then the terephthaloyl dichloride was subsequently added to form a para–meta benzoic polyamide prepolymer. The polyimide prepolymers were also prepared by using 4,4′-diphenylmethane disocyanate to react with pyromellitic dianhydride, 3,3′,4,4′-benzophenonetetracarboxylic dianhydride, or 3,3′,4,4′-sulfonyldiphthalic anhydride using the direct one-pot method to improve their solubility, but without sacrificing thermal and physical properties. From the experimental results, the inherent viscosity of the copolymers was 0.72–1.15 dL/g and they were readily soluble in a wide range of organic hot solvents such as N-methyl-2-pyrrolidone, dimethylimidazole, N,N-dimethylacetamide, dimethyl sulfoxide, and N,N-dimethylformamide; however, some of the copolymers were not soluble in pyridine. The solubility was related to their chemical structure. Those copolymers with sulfonyl and high amide content displayed good solubility. All the poly(amide-imide)s had a glass transition temperature of 260–324°C, but the melting point did not vary much. The 10% weight loss temperatures were in a range of 463–580°C in nitrogen and 450–555°C in an air atmosphere. The tensile strength, elongation at break, and initial modulus of the copolymer films ranged from 59 to 102 MPa, 3.1 to 5.1%, and 1.52 to 3.59 GPa, respectively. These copolymers, except those of high imide content (e.g., P-6, B-4, B-6 and D-6), which showed an amorphous structure, mostly display a crystalline morphology. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2671–2679, 1999     

Chemical synthesis,characterization, and properties of conducting copolymers of imidazole and pyridine

A series of conducting copolymers were synthesized by chemical oxidative polymerization of imidazole (Imi) and pyridine (Py) in acetonitrile medium at ambient temperature. The yield, solubility, and conductivity of the copolymers were measured by changing the Imi/Py molar ratio from 0/100 to 100/0. The as‐prepared Imi/Py conducting copolymers were characterized by UV‐Visible, FTIR, ¹H‐NMR, DSC, TGA, and XRD. The results suggest that the resulting copolymers were more easily soluble in most of the organic solvents than in polyimidazole. The polymer obtained is a real copolymer containing imidazole and pyridine units, but the Imi content calculated on the basis of the proton NMR spectra is lower than feed Imi content. The thermostability of the Imi/Py copolymer increases with increasing Imi unit content. The copolymers show comparatively higher conductivity and higher thermal stability than the homopolymer polypyridine and are lower than those of polyimidazole. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Melt polymerized aramid/polycaprolactam copolymer and its fiber

A melt polymerization method was introduced to synthesize a series of aramid/polycaprolactam copolymers (APA). In this strategy, a modified aramid (MA) containing para‐ and meta‐disubstituted benzene rings was dissolved in molten caprolactam (CPL) and then copolymerized with CPL to obtain APA. In contrast to neat polycaprolactam (PA6), the glass transition temperature (T_g) and crystallization temperature (T_c) of APA were maximally raised by 9 °C and 135 °C, respectively. The crystal form of APA was similar to that of PA6 and only one α‐form existed in the crystallization region of the copolymer. However, the completeness of the crystal grains was disrupted by the aramid component and the apparent viscosities (η_a) of APA were obviously higher than for PA6, which indicated that the aromatic segments in the APA backbone restricted the mobility of the PA6 chains. In addition, APA was easily melt‐spun into continuous fiber, and the tensile strength of the fiber was significantly increased by 140.97% with introduction of 5 wt% MA compared with neat PA6 fiber. © 2013 Society of Chemical Industry     

Catalysts for the preparation of polybenzimidazoles

The single-stage preparation of poly[2,2′-(m-phenylene)-5,5′-bibenzimidazole] (PBI), from 3,3′,4,4′-tetraaminobiphenyl (TAB) with isophthalic acid (IPA) in the presence of a catalyst, was explored and developed. The effects of a variety of catalysts on the polymerization of TAB with IPA and/or diphenyl isophthalate were screened and evaluated. Many organo phosphorus and silicon compounds catalyzed the PBI condensation reactions, increased the molecular weight, and improved the quality of PBI polymers. Fiber and reverse osmosis membrane properties of PBI prepared from TAB and IPA were comparable to those for commercial standard PBI prepared from TAB and diphenyl isophthalate. © 1994 John Wiley & Sons, Inc.     

Effect of steric constraints on the physico‐electrochemical properties of sulfonated polyaromatic copolymers

The impact of incorporating additional steric restrictions into highly sterically encumbered sulfonated polyaromatic polymers was investigated. Copolymers possessing between 0 and 10% nonlinear ortho or meta biphenyl units in an otherwise linear para biphenyl‐containing sulfo‐phenylated poly(phenylene) were synthesized in yields >80% and evaluated on the basis of their physical and electrochemical properties. When incorporated into sulfonated copolymers in ≤5 mol%, ortho and meta linked biphenyl moieties reduced membrane swelling in water by up to 23 and 19 vol%, respectively, compared to strictly para biphenyl‐linked copolymers. Despite this, copolymers possessing nonlinear, biphenyl‐linked monomers displayed a decrease in proton conductivity and mechanical strength. This study reinforces the importance of considering restricted rotation, backbone flexibility, and chain entanglement in the design of polymers aimed at improving their physical and electrochemical properties. © 2020 Society of Industrial Chemistry     

Molecular recognition: polymers comprising isomeric meta‐/para‐isopropylphenol and N‐isopropylacrylamide and their supramolecular complexes with methylated β‐cyclodextrin

We describe the molecular recognition of polymeric attached isomers meta‐isopropylphenol and para‐isopropylphenol, respectively, in a copolymer of N‐isopropylacrylamide (NIPAAm) by use of randomly methylated β‐cyclodextrin (RAMEB‐CD). The acrylic monomers 4‐ and 3‐isopropylphenylacrylate were synthesized and radically copolymerized with NIPAAm yielding the corresponding polymers. The supramolecular structures resulting from complexation with RAMEB‐CD were characterized using dynamic light scattering, turbidity, NMR spectroscopy and isothermal titration. We found differences in binding constant, mean coil size and cloud point as a result of different complexations of the mentioned polymer‐bound isomers with RAMEB‐CD. Copyright © 2012 Society of Chemical Industry     

Compatibility of poly(2,6-dimethyl-1,4-phenylene oxide)/poly(fluorostyrene-co-chlorostyrene) blends

The compatibility of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) with random copolymers of ortho- and para-fluorostyrene as well as with ortho- and para-chlorostyrene of various copolymer compositions was examined. The compatibility was studied by DSC and visual observation of film clarity. It was found that copolymers of ortho-fluorostyrene with para-chlorostyrene containing 15–74 mol % p-CIS are compatible with PPO in all proportions. Compatibility of the PPO/poly-(ortho-fluorostyrene-co-ortho-chlorostyrene) system was observed for copolymers containing between 15 and 36 mol % ortho-chlorostyrene. Copolymers of para-fluorostyrene with para-chlorostyrene, as well as copolymers of para-fluorostyrene with ortho-chlorostyrene appear to be incompatible with PPO at 210°C.     

Polypyrrole–vinyl aniline modified cyclohexanone formaldehyde resin copolymers: a comparative study of the resin preparation

In this study, the synthesis of polypyrrole‐b‐vinyl aniline modified cyclohexanone formaldehyde resin (PPy‐b‐CFVAnR) block copolymers by a combination of condensation polymerization and chemical oxidative polymerization processes was examined. First, a cyclohexanone formaldehyde resin containing vinyl aniline units [4‐ vinyl aniline modified cycl?ohexanone formaldehyde resin (CFVAnR)] was prepared by a direct condensation reaction of 4‐vinyl aniline and cyclohexanone with formaldehyde in an in situ modification reaction. CFVAnR and pyrrole (Py) were then used with a conventional method of in situ chemical oxidative polymerization. The reactions were carried out with heat‐activated potassium persulfate salt in the presence of p‐toluene sulfonic acid in a dimethyl sulfoxide–water binary solvent system; this led to the formation of desired block copolymers. The effects of the oxidant–monomer molar ratio, dopant existence, addition order of the reactants, and reaction temperature on the yield, conductivity, and morphology of the resulting products were investigated. PPy‐b‐CFVAnR copolymers prepared with a resin‐to‐Py molar ratio of 1:40 showed conductivity in the range 3.7 × 10^?1 to 3.8 × 10^?2 S/cm. Oxidant‐to‐Py molar ratios of 0.5 and 1.0 were proposed to be the optimum stoichiometries for higher conductivity and yield, respectively, of the copolymer. The morphology of the copolymer (PPy‐b‐CFVAnR) was investigated with environmental scanning electron microscopy analyses. The results indicate that the surface of the copolymer was composed of well‐distributed nanospheres with average particle diameters of 60–85 nm. Also, the synthesized PPy‐b‐CFVAnR had a higher thermal stability than the pure CFVAnR. The chemical composition and structure of the PPy‐b‐CFVAnR copolymers were characterized by Fourier transform infrared spectroscopy and measurement. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42841.     

Investigation of the electroactivity,conductivity, and morphology of poly(pyrrole‐co‐N‐alkyl pyrrole) prepared via electrochemical nanopolymerization and chemical polymerization

The copolymerization of pyrrole (Py) with N‐ethyl pyrrole, N‐butyl pyrrole, and N‐octyl pyrrole (NOPy) was carried out by electrochemical and chemical oxidation. In the electrochemical method, copolymer thin films with different feed ratios of monomers were synthesized by the cyclic voltammetry method in a lithium perchlorate (LiClO₄)/acetonitrile (CH₃CN) electrolyte on the surface of a glassy carbon working electrode. The deposition conditions on the glassy carbon, the influence of the molar ratios of the monomers on the formation of the copolymers, and the electroactivity of the copolymers were investigated with cyclic voltammetry. Nanoparticles made of a conjugate of the copolymers with different feed ratios of monomers were prepared by chemical polymerization (conventional and interfacial methods) in the presence of iron(III) chloride hexahydrate (FeCl₃·6H₂O) as the oxidant. Nanostructural copolymers with higher conductivities were synthesized by simple tuning of the preparation conditions in a two‐phase medium. Fourier transform infrared spectroscopy, scanning electron microscopy, and four‐probe conductivity measurement techniques were applied for the characterization of the obtained copolymers. The conductivity of the obtained copolymer by an interfacial method with chloroform as the organic phase was 20 times higher than the copolymer obtained via an interfacial method with toluene as the organic phase and 700 times higher than the copolymer prepared by the conventional method (for a molar ratio of 70 : 30 Py : NOPy). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

A novel polybenzimidazole composite modified by sulfonated graphene oxide for high temperature proton exchange membrane fuel cells in anhydrous atmosphere

A novel functional graphene with high ion exchange capacity (IEC) was prepared by grafting reaction induced by ⁶⁰Co γ‐ray irradiation using graphene oxide. Then, polybenzimidazole/radiation grafting graphene oxide (PBI/RGO) composite membranes were prepared by the solution‐casting method and doped with phosphoric acid (PA) to improve their proton conductivity. The properties of PBI/GO/PA and PBI/RGO/PA membranes including the PA doping level, chemical stability, proton conductivity and mechanical properties were evaluated and compared. The tensile strength of PBI/RGO/PA membranes (ranging from 27.3 to 38.5 MPa) increases at first and then decreases with the increase of the RGO content, and is significantly higher than that of other PA doped PBI‐based membranes. The proton conductivity of PBI/RGO‐3/PA membrane is 28.0 mS cm^?1 at 170 °C without humidity, with an increase of 72.0% compared with that of PBI/PA membrane. These results suggest that PBI/RGO/PA membranes have the potential to be used as high‐temperature proton exchange membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44986.     

Blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 toughened by maleated polystyrene‐based copolymers: Mechanical properties,morphology, and rheology

Poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 (PPO/PA6 30/70) blends were impact modified by addition of three kinds of maleated polystyrene‐based copolymers, i.e., maleated styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), maleated methyl methacrylate‐butadiene‐styrene copolymer (MBS‐g‐MA), and maleated acrylonitrile‐butadiene‐styrene copolymer (ABS‐g‐MA). The mechanical properties, morphology and rheological behavior of the impact modified PPO/PA6 blends were investigated. The selective location of the maleated copolymers in one phase or at interface accounted for the different toughening effects of the maleated copolymer, which is closely related to their molecular structure and composition. SEBS‐g‐MA was uniformly dispersed in PPO phase and greatly toughened PPO/PA6 blends even at low temperature. MBS‐g‐MA particles were mainly dispersed in the PA6 phase and around the PPO phase, resulting in a significant enhancement of the notched Izod impact strength of PPO/PA6 blends from 45 J/m to 281 J/m at the MBS‐g‐MA content of 20 phr. In comparison, the ABS‐g‐MA was mainly dispersed in PA6 phase without much influencing the original mechanical properties of the PPO/PA6 blend. The different molecule structure and selective location of the maleated copolymers in the blends were reflected by the change of rheological behavior as well. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Thermal and sonochemical degradation kinetics of poly(n‐butyl methacrylate‐co‐alkyl acrylates): Variation of chain strength and stability with copolymer composition

The thermal degradation of poly(n‐butyl methacrylate‐co‐alkyl acrylate) was compared with ultrasonic degradation. For this purpose, different compositions of poly (n‐butyl methacrylate‐co‐methyl acrylate) (PBMAMA) and a particular composition of poly(n‐butyl methacrylate‐co‐ethyl acrylate) (PBMAEA) and poly(n‐butyl methacrylate‐co‐butyl acrylate) (PBMABA) were synthesized and characterized. The thermal degradation of polymers shows that the poly(alkyl acrylates) degrade in a single stage by random chain scission and poly(n‐butyl methacrylate) degrades in two stages. The number of stages of thermal degradation of copolymers was same as the majority component of the copolymer. The activation energy corresponding to random chain scission increased and then decreased with an increase of n‐butyl methacrylate fraction in copolymer. The effect of methyl acrylate content, alkyl acrylate substituent, and solvents on the ultrasonic degradation of these copolymers was investigated. A continuous distribution kinetics model was used to determine the degradation rate coefficients. The degradation rate coefficient of PBMAMA varied nonlinearly with n‐butyl methacrylate content. The degradation of poly (n‐butyl methacrylate‐co‐alkyl acrylate) followed the order: PBMAMA < PBMAEA < PBMABA. The variation in the degradation rate constant with composition of the copolymer was discussed in relation to the competing effects of the stretching of the polymer in solution and the electron displacement in the main chain. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Effect of methyl position on the dynamic mechanical and shape‐memory properties of cresol‐based polybenzoxazines

Three difunctional benzoxazines were synthesized from cresol isomers (o‐, m‐, and p‐methylphenols), 1,3‐bis(3‐aminopropyl)‐1,1,3,3‐tetramethyldisiloxane, and formaldehyde. The ring‐opening polymerization temperature decreases in the order of ortho‐, para‐, and meta‐positions of methyl group for the benzoxazine monomers, whereas the glass transition temperature increases in the order of ortho‐, para‐, and meta‐positions of methyl group for the resultant polybenzoxazines. In addition, the polybenzoxazines exhibit one‐way dual‐shape‐memory behavior in response to changes in temperature, and the shape‐memory effects are evaluated by tensile and bending tests with a temperature program based on glass transition temperature. The o‐ and p‐cresol‐based polybenzoxazines exhibit higher shape‐memory performance than their m‐cresol‐based analogue/counterpart. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45443.     

Application of styrene‐acrylonitrile random copolymer–polyarylate block copolymer as reactive compatibilizer for polyamide and acrylonitrile‐butadiene‐styrene blends

Styrene‐acrylonitrile random copolymer (SAN) and polyarylate (PAr) block copolymer were applied as a reactive compatibilizer for polyamide‐6 (PA‐6)/acrylonitrile‐butadiene‐styrene (ABS) copolymer blends. The SAN–PAr block copolymer was found to be effective for compatibilization of PA‐6/ABS blends. With the addition of 3.0–5.0 wt % SAN–PAr block copolymer, the ABS‐rich phase could be reduced to a smaller size than 1.0 μm in the 70/30 and 50/50 PA‐6/ABS blends, although it was several microns in the uncompatibilized blends. As a result, for the blends compatibilized with 3–5 wt % block copolymer the impact energy absorption reached the super toughness region in the 70/30 and 50/50 PA‐6/ABS compositions. The compatibilization mechanism of PA‐6/ABS by the SAN–PAr block copolymer was investigated by tetrahydrofuran extraction of the SAN–PAr block copolymer/PA‐6 blends and the model reactions between the block copolymer and low molecular weight compounds. The results of these experiments indicated that the SAN–PAr block copolymer reacted with the PA‐6 during the melt mixing process via an in situ transreaction between the ester units in the PAr chain and the terminal amine in the PA‐6. As a result, SAN–PAr/PA‐6 block copolymers were generated during the melt mixing process. The SAN–PAr block copolymer was supposed to compatibilize the PA‐6 and ABS blend by anchoring the PAr/PA‐6 and SAN chains to the PA‐6 and ABS phases, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2300–2313, 2002     

Synthesis and characterization of functionalized syndiotactic polystyrene copolymers

Functionalized syndiotactic polystyrene copolymers were synthesized and characterized. The syndiotactic polystyrene copolymers, poly(styrene‐co‐4‐methylstyrene) (sPSMS), were prepared by styrene with 4‐methylstyrene with a metallocene/methylaluminoxane catalyst. In addition, grafted copolymers, chemically grafted with isoprene onto an sPSMS backbone [poly(styrene‐co‐4‐methylstyrene)‐g‐polyisoprene (sPSMS‐g‐PIP)] were synthesized by anionic grafting polymerization with a metallation reagent. In this study, we also examined the effect of the degree of functionalization (epoxidation) on the polymer structure of the sPSMS‐g‐PIP copolymers. Experimental results indicate that the crystallinity of the sPSMS‐g‐PIP copolymer was lower than that of the ungrafted sPSMS copolymer. Moreover, the epoxy‐containing sPSMS‐g‐PIP copolymer effectively increased the thermal stability more than did the sPSMS‐g‐PIP copolymer alone. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1038–1045, 2002     

Crystallization and melting behavior of poly(ε‐caprolactone‐co‐δ‐valerolactone) and poly(ε‐caprolactone‐co‐L‐lactide) copolymers with novel chain microstructures

Nuclear magnetic resonance spectroscopy (NMR) characterization of the statistical copolymers of this study showed that the poly(ε‐caprolactone‐co‐L‐lactide)s, with ε‐caprolactone (ε‐CL) molar contents ranging from 70 to 94% and ε‐CL average sequence length (l_CL) between 2.20–9.52, and the poly(ε‐caprolactone‐co‐δ‐valerolactone)s, with 60 to 85% of ε‐CL and l_CL between 2.65–6.08, present semi‐alternating (R→2) and random (R～1) distribution of sequences, respectively. These syntheses were carried out with the aim of reducing the crystallinity of poly(ε‐caprolactone) (PCL), needed to provide mechanical strength to the material but also responsible for its slow degradation rate. However, this was not achieved in the case of the ε‐caprolactone‐co‐δ‐valerolactone (ε‐CL‐co‐δ‐VAL). Non‐isothermal cooling treatments at different rates and isothermal crystallizations (at 5, 10, 21 and 37°C) were conducted by differential scanning calorimetry (DSC), and demonstrated that ε‐CL copolymers containing δ‐valerolactone (δ‐VAL) exhibited a larger crystallization capability than those of L‐lactide (L‐LA) and also arranged into crystalline structures over shorter times. The crystallization enthalpies of the ε‐CL‐co‐δ‐VAL copolymers during the cooling treatments and their heat of fusion (ΔH_m) at the different isothermal temperatures were very large (i.e. ΔH_c > 53 Jg^?1) and in some cases, unrelated to the copolymer composition. In some compositions, such as the 60 : 40, Wide Angle X‐ray Scattering (WAXS) proved that that these two lactones undergo isomorphism and co‐crystallize in a single cell. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42534.     

Synthesis of novel functional polyolefin containing carboxylic acid via Friedel-Crafts acylation reaction

The strong polar group, carboxylic acid, has triumphantly been introduced into ethylene and allylbenzene copolymers without obvious degradation or crosslinking via Friedel-Crafts (F-C) acylation reaction with glutaric anhydride (GA), succinic anhydride (SA) and phthalic anhydride (PA) in the presence of anhydrous aluminum chloride in carbon disulfide. Some important reaction parameters were examined in order to optimize the acylation process. In the optimum reaction conditions, almost all of the phenyls can be acylated with any anhydride. The microstructure of acylated copolymer was characterized by FT-IR, ¹H NMR and ¹H-¹H COSY. All the peaks of acylated copolymers can be accurately attributed, which indicates that all the acylation reactions occur only at the para-positions of the substituent of the aromatic rings. The thermal behavior was studied by differential scanning calorimetry (DSC), showing that the melting temperatures (T_ms) of acylated copolymers with GA firstly decrease slowly and then increase significantly with the increase of the amount of carboxyl acid groups.