Performance improvement of dye-sensitizing solar cell by semi-rigid triarylamine-based donors

Novel organic dyes (IDB and ISB dyes), which contain 5-phenyl-iminodibenzyl (IDB) and 5-phenyl-iminostilbene (ISB) as electron donors and a cyanoacrylic acid moiety as an electron acceptor and an anchoring group, connected with a thiophene as a π-conjugated system, have been synthesized and used as the sensitizers for dye-sensitized solar cells (DSSCs). The photophysical and electrochemical properties of the dyes were investigated by absorption spectrometry, cyclic voltammetry and density functional theory calculations. As demonstrated, the IDB and ISB unit exhibited stronger electron-donating ability and broader absorption spectra when coated onto TiO₂. The DSSC based on ISB-2 consisting of ISB unit produced 5.83% of η (J_sc = 13.14 mA cm⁻², V_oc = 0.64 V, and ff = 0.68) under 100 mW cm⁻² simulated AM 1.5 G solar irradiation.     

Low bandgap EDOT-quinoxaline and EDOT-thiadiazol-quinoxaline conjugated polymers: Synthesis, redox, and photovoltaic device

Three new low bandgap conjugated copolymers with 3,4-ethylenedioxythiophene (EDOT) as donor and 2,3-bis(4-octyloxyphenyl)-quinoxaline (P1), 2,3-bis(4-octyloxyphenyl)-thiadiazol-quinoxaline (P2, P3) as acceptors were synthesized by Stille cross-coupling reaction, and their optical and electrochemical properties were studied. These polymers exhibited optical bandgap of 1.77, 1.29 and 1.13 eV, for P1, P2 and P3, respectively. Photovoltaic cells with device configuration of ITO/PEDOT: PSS/Copolymer: PCBM (1:4 w/w)/LiF/Al were fabricated. The measurements revealed an open-circuit voltage (V_oc) of 0.52 V, short-circuit current density (J_sc) of 3.24 mA/cm² and power conversion efficiency (PCE) of 0.60% for P1, and showed a V_oc of 0.33 V, J_sc of 2.11 mA/cm², PCE of 0.39% for P2.     

Bridge length effect of new dinuclear constrained geometry catalysts on controlling the polymerization behaviors of ethylene/styrene copolymerization

According to the observable evidence from ¹H and ¹³C nuclear magnetic resonance and mass spectrometry, new dinuclear constrained geometry catalysts (DCGCs) with a structure of [{Ti(η⁵:η¹-(C₉H₅)Si(CH₃)₂N^tBu)Cl₂(CH₂)_n}₂(C₆H₄)] [n = 0 (10), n = 1 (11), n = 2 (12)] were synthesized successfully. Copolymerization of ethylene and styrene were tested by using three new DCGCs and Dow CGC. The catalyst activity, the molecular weight (MW) and styrene content of the copolymers were sharply improved as the bridge structure was transformed from para-phenyl (10) to para-xylyl (11) and para-diethylenephenyl (12). The activity of 11 and 12 was about four to five times greater than that of 10 regardless of the polymerization conditions. In addition, the capability to form high MW polymers increased in the order of Dow CGC ≈ 10 < 11 < 12. The styrene contents in copolymers generated by 11 and 12 were higher than those of 10.     

Alkyloxy substituted organic dyes for high voltage dye-sensitized solar cell: Effect of alkyloxy chain length on open-circuit voltage

Three novel organic dyes (SB1, SB2, and SB3) containing 4-(hexyloxy)-N-(4-(hexyloxy)phenyl)-N-phenylaniline as electron donor and cyanoacrylic acid as electron acceptor bridged by alkyloxy (methyl = SB1, propyl = SB2 and hexyl = SB3) substituted p-phenylenevinylene linkers have been synthesized. Density functional theory (DFT) has employed to study electron distribution and intramolecular charge transfer. Increase in alkyl chain length in alkyloxy substituent leads to increase in open-circuit voltage (V_OC), which is found to be related to the increased electron lifetime at open-circuit condition. Under AM 1.5 G 1 sun light illumination (100 mW/cm²), an optimized SB3-sensitized cell show a short-circuit photocurrent density (J_SC) of 12.83 mA/cm², an open-circuit voltage (V_OC) of 0.745 V and a fill factor (FF) of 0.64, corresponding to an overall conversion efficiency (η) of 6.12%. Little degradation in η observed over 40 days is indicative of long-term stability of the SB-series dyes.     

Dinaphtho-s-indacene-based copolymers for inverted organic solar cells with high open-circuit voltages

We report on the synthesis and characterization of a series of donor–acceptor copolymers (PF1, PF2, PF3 or PF4) based on a dinaphtho-s-indacene (DNI) donor unit and four different acceptor units. The molecular weights of the copolymers were determined by using gel permeation chromatography, and their electrochemical properties were investigated by cyclic voltammetry. All four copolymers showed deep-lying highest occupied molecular orbital energy levels. Inverted bulk heterojunction solar cells were fabricated by using the synthesized copolymers as the electron donor material and 6,6-phenyl-C71-butyric acid methyl ester (PC₇₁BM) as the electron acceptor material. Inverted solar cells based on PF1:PC₇₁BM (1:4, w/w) exhibited a power conversion efficiency (PCE) of 3.07%, a high open-circuit voltage (V_oc) of 0.99 V, a short-circuit current density (J_sc) of 7.85 mA/cm², and a fill factor of 39.5% under the AM1.5G illumination. With the same fabrication method, the inverted devices based on PF2, PF3 and PF4 showed PCEs of 2.62, 1.18 and 1.32%, and V_oc values of 0.97, 0.91 and 0.80 V, respectively.     

Metallocene-catalyzed synthesis of polyethylenes with side-chain triarylamines: Effects of catalyst structure and triarylamine functionality

The copolymerization of ethylene with 8-triarylamine (TAA) substituted 1-octene monomers (TAA = triphenylamine (M1), N,N-diphenyl-m-tolylamine (M2), N,N-diphenyl-1-naphthylamine (M3)) using various types of group 4 single-site catalytic systems (Cp₂ZrCl₂ (C1), rac-EBIZrCl₂ (C2), rac-SBIZrCl₂ (C3), i-PrCpFluZrCl₂ (C4), Me₂Si(η⁵-C₅Me₄)(η¹-N-^tBu)TiCl₂ (C5)) was investigated to prepare functionalized polyethylene with side-chain TAA groups. The metallocene/methylaluminoxane (MAO) catalytic systems (C1-C4) efficiently lead to the production of high-molecular-weight poly(ethylene-co-M1). While the C4/MAO catalytic system shows the highest comonomer response, the C5/MAO system exhibits the poor compatibility with the M1 comonomer. Copolymerization results of ethylene with M1-M3 using C4/MAO indicate that M1-M3 are well tolerated by both the cationic active species of C4 and MAO cocatalyst, giving rise to the copolymers with high levels of activity and molecular weight. Inspection of the aliphatic region of the ¹³C NMR spectra of the copolymers (P1-P3) having ca. 11 mol% of M1-M3, respectively, reveals the presence of isolated comonomer units with prevailing [EEMEE] monomer sequences in the polymer chain. UV-vis absorption and PL spectra exhibit an apparent low-energy band broadening for P1 and P2 indicative of intrachain aggregate formation. Whereas P2 and P3 undergo completely reversible one-electron oxidation process, P1 shows relatively poor oxidational stability.     

Synthesis and electro-optical properties of helical polyacetylenes carrying carbazole and triphenylamine moieties

Novel chiral acetylene monomers bearing carbazole and triphenylamine groups, namely, (S)-3-butyn-2-yl 2-(9-carbazolyl)ethyl carbonate (1) and (S)-3-butyn-2-yl 4-(diphenylamino)benzoate (2) were synthesized, and polymerized with Rh⁺(nbd)[η⁶-C₆H₅B⁻(C₆H₅)₃] catalyst to give the corresponding polymers with moderate molecular weights (M_n 13.0 × 10³ and 15.5 × 10³) in good yields (86% and 88%). CD spectroscopic studies revealed that poly(1) and poly(2) took predominantly one-handed helical structure in CHCl₃. The helical structures of poly(1) and poly(2) were very stable against heating and addition of MeOH. The solution of poly(1) and poly(2) emitted fluorescence in 0.52% and 7.2% quantum yields, which were lower than those of the corresponding monomers 1 and 2 (22.5% and 76.5%). The cyclic voltammograms of the polymers indicated that the oxidation potentials of the polymers were lower than those of the monomers. The polymers showed electrochromism and changed the color from pale yellow to pale blue by application of voltage, presumably caused by the formation of polaron at the carbazole and triphenylamine moieties. The onset temperatures of weight loss of poly(1) and poly(2) were 225 and 270 °C under air.     

Synthesis of conjugated polymers with broad absorption bands and photovoltaic properties as bulk heterojuction solar cells

Two new broad absorbing alternating copolymers, poly[1-(2,6-diisopropylphenyl)-2,5-bis(2-thienyl)pyrrole-alt-4,7-bis(3-octyl-2-thienyl)benzothiadiazole] (PTPTTBT-P1) and poly[1-(p-octylphenyl)-2,5-bis(2-thienyl)pyrrole-alt-4,7-bis(3-octyl-2-thienyl)benzothiadiazole] (PTPTTBT-P2), were prepared via Suzuki polycondensation with high yields. The two polymers were found to show characteristic absorption in the visible region of the solar spectrum. Interestingly the absorption of PTPTTBT-P1 was found to cover the visible region from 350 to 650 nm with the broad and flat absorption maximum from 440 to 510 nm in film and the absorption of PTPTTBT-P2 was found to cover the visible region from 350 to 950 nm with the relatively distinct absorption maxima at 425 and 522 nm and very weak absorption maximum at 832 nm in film. The electrochemical band gaps of the polymers were calculated to be 1.88 eV and 1.87 eV, respectively, while the optical band gaps of the polymers were calculated to be 1.94 eV and 1.87 eV, respectively. The photovoltaic properties of polymers were investigated with bulk heterojunction (BHJ) solar cells fabricated in ITO/PEDOT:PSS/polymer:PC₇₀BM(1:5 wt%)/TiOx/Al configurations. The maximum power conversion efficiency (PCE) of the solar cell composed of PTPTTBT-P1:PC₇₀BM as an active layer was 1.57% with current density (J_sc) of 8.17 mA/cm², open circuit voltage (V_oc) of 0.52 V and fill factor (FF) of 36%.     

Synthesis and properties of polyacetylenes carrying N-phenylcarbazole and triphenylamine moieties

Novel acetylene monomers containing N-phenyl-substituted carbazole (Cz) and triphenylamine (TPA) groups, namely, 3-ethynyl-9-phenylcarbazole (1) and p-(N,N-diphenylamino)phenylacetylene (2) were synthesized, and polymerized with several Rh-, W-, and Mo-based catalysts. Poly(1) and poly(2) with high number-average molecular weights (15?500-974?000) were obtained in good yields (77-97%), when [(nbd)RhCl]₂-Et₃N (nbd = norbornadiene) was used as a catalyst. The polymers exhibited UV-vis absorption peaks derived from the Cz and TPA moieties at 250-350 nm and polyacetylene backbone above 350 nm. The UV-vis absorption band edge wavelengths of the polymers were longer than those of the corresponding monomers. Poly(2) exhibited a UV-vis absorption peak at a longer wavelength than poly(1) did, which indicates that poly(2) has main chain conjugation longer than that of poly(1). The molecular weights and photoluminescence quantum yields of the polymers obtained by the polymerization using [(nbd)RhCl]₂-Et₃N were larger than those of the Rh⁺(nbd)[η⁶-C₆H₅B⁻(C₆H₅)₃]-based counterparts. The cyclic voltammograms of the polymers indicated that they had clear electrochemical properties; the onset oxidation voltage of poly(1) was higher than those of N-alkyl-substituted Cz derivatives. The polymers showed electrochromism and changed the color from pale yellow to blue by application of voltage, presumably caused by the formation of charged polaron at the Cz and TPA moieties. The temperatures for 5% weight loss of the polymers were around 350-420 °C under air, indicating the high thermal stability.     

Novel D-π-A system based on zinc porphyrin dyes for dye-sensitized solar cells: Synthesis, electrochemical, and photovoltaic properties

We have designed and synthesized novel zinc porphyrin dyes which have a D-π-A system based on porphyrin derivatives containing a triphenylamine (TPA) electron-donating group and a phenyl carboxyl anchoring group substituted at the meso position of the porphyrin ring, yielding the push-pull porphyrins as the most efficient green dye for dye-sensitized solar cell (DSSC) applications. The synthesis and characterization of a novel D-π-A system based on zinc-porphyrin derivatives have been investigated through their photophysical and photoelectrochemical studies. A large red-shift of the absorption maxima due to introduction of the TPA moiety at the meso position of the porphyrin ring was expected in the D-π-A porphyrins, but the absorption maxima of HKK-Por dyes were a little red-shifted in contrast to Zn[5,-10,15-triphenyl-20-(4-carboxylphenyl)-porphyrin], due to the tilted structure between TPA and the porphyrin unit. Under the photovoltaic performance measurement, the maximum incident photon-to-current conversion efficiency (IPCE) value of the DSSC based on HKK-Por 5 was slightly higher than the efficiencies of the DSSCs based on other HKK-Por dyes due to the introduction of the alkoxy group into the TPA moiety at the meso position of the porphyrin ring. A maximum photon-to-electron conversion efficiency of 3.36% was achieved with the DSSC based on HKK-Por 5 dye (J_SC = 9.04 mA/cm², V_OC = 0.57 V, FF = 0.66) under AM1.5 irradiation (100 m Wcm⁻²).     

Luminescent polyethylene with side-chain triarylboranes: Synthesis and fluoride sensing properties

The direct copolymerization of ethylene with an electron-deficient borane monomer (1) using a single-site catalytic system, Me₂Si(η⁵-C₅Me₄)(η¹-N-^tBu)TiCl₂ (CGC)/methylaluminoxane (MAO) efficiently leads to the novel class of luminescent polyethylene with pendent triarylborane groups. The catalytic system provides high-molecular-weight copolymers with controlled incorporation of 1. Characterization by multinuclear NMR spectroscopy reveals that the copolymers constitute a well-defined polymer structure with base-free tricoordinate boron centers. While UV-vis absorption and PL spectra of copolymers display almost identical absorption and emission features with those of 1, the copolymer (8.8 mol% of 1) shows the enhanced emission quenching efficiency with 70% amplification effect upon addition of fluoride ion in solution. Particularly, the thin film of the copolymer exhibits the high fluorescence quenching response in the presence of a very low concentration of fluoride ion (4.5 μM) in THF.     

Paired electrochemical synthesis of new organosulfone derivatives

Electrochemical oxidation of “cathodically generated 4-aminocatechol (2)” has been studied in the presence of 4-toluenesulfinic acid (4a) and benzenesulfinic acid (4b) as nucleophiles in aqueous solutions, using cyclic voltammetry and controlled-potential coulometry. The results indicate that the o-benzoquinone derived from 4-aminocatechol (2) participates in Michael addition reaction with 4a or 4b to form the corresponding new organosulfone derivatives (5a and 5b). In this work we have proposed a mechanism for the electrode process. A Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ redox mediator was used for the anodic oxidation of 4-aminocatechol (2) to the corresponding o-quinone 3. The indirect electrochemical process consists of a multi-step such as (a) cathodic reduction of 4-nitrocatechol (1) to 4-aminocatechol (2), (b) chemical oxidation of 4-aminocatechol (2) to 4-aminoquinone (3) with the resulting Fe(CN)₆³⁻, (c) the chemical reaction of 4-aminoquinone (3) with 4-toluenesulfinic acid (4a) or benzenesulfinic acid (4b), and (d) the anodic regeneration of Fe(CN)₆³⁻. The paired electrochemical synthesis of organosulfone derivatives (5a and 5b) has been successfully performed in an one-pot process at carbon rod electrode as a working and platinum as a counter electrode in an undivided cell.     

Homo- and R/S-copolymerizations of chiral methylpropargyl esters carrying pyrene moieties, and optical properties of the formed polymers

Pyrene-functionalized chiral methylpropargyl esters, (R)-3-butyn-2-yl-1-pyrenebutyrate [(R)-1], (S)-3-butyn-2-yl-1-pyrenebutyrate [(S)-1], (R)-3-butyn-2-yl-1-pyrenecarboxylate [(R)-2], and 3-butyn-2-yl-1-pyrenecarboxylate [(R,S)-2] were polymerized with (nbd)Rh⁺[η⁶-C₆H₅B⁻(C₆H₅)₃] to obtain the corresponding polymers with moderate molecular weights (M_n: 10?500-66?500) in good yields (82-97%). All the polymers were soluble in CHCl₃, CH₂Cl₂, and THF. The polarimetric and CD spectroscopic data indicated that poly[(R)-1], poly[(S)-1], and poly[(R)-2] existed in a helical structure with predominantly one-handed screw sense in these solvents. The helical structure of poly[(R)-1] and poly[(S)-1] was stable upon heating and addition of MeOH, while that of poly[(R)-2] changed upon MeOH addition. The copolymerization of (R)-1 with (S)-1 was also conducted to obtain the copolymers satisfactorily. Poly[(R)-1], poly[(S)-1], and poly[(R)-2] emitted fluorescence smaller than the corresponding racemic copolymers. The fluorescence intensity was tuned by the addition of MeOH to THF solutions of the polymers.     

Synthesis and characterization of biodegradable polylactides and polylactide-block-poly(Z-lysine) copolymers

The reaction of (R,R)-trans-1,2-bis(2,4,6-triisopropylbenzenesulfonamidato)cyclohexane (^RRTBSC-H₂, 1) with MN[Si(CH₃)₃] in tetrahydrofuran (THF) produces [(^RRTBSC)₂M₄(THF)₄] (2: M = Li, 3: M = Na, 4: M = K). Experimental results show that all three complexes 2-4 are active toward the ring-opening polymerization of l-lactide and compound 2 efficiently catalyzes the polymerization of l-lactide in the presence of a variety of alcohols in a controlled fashion with very narrow polydispersity index. In addition, a variety of biodegradable poly(l-lactide)-block-poly(N_ξ-carbobenzyloxy-l-lysine) block copolymers with different ratios have also been synthesized using poly(l-lactide) containing amino chain end (PLLA-NH₂) as a macroinitiator.     

Highly active and trans-1,4 specific polymerization of 1,3-butadiene catalyzed by 2-pyrazolyl substituted 1,10-phenanthroline ligated iron (II) complexes

A new family of iron (II) complexes (2a–h) bearing tridentate 2-pyrazolyl substituted 1,10-phenanthroline ligands were successfully prepared and characterized by IR spectroscopy, elemental analysis, and mass spectra. Complexes 2a–f and 2h were further confirmed by the X-ray crystallographic analysis. 2a, 2b, 2e, and 2f adopted distorted trigonal bipyramidal configuration. 2c displayed a distorted octahedron formed by six coordinated nitrogen atoms of the two ligands. Linked by two bridged chloride atoms, complex 2d was a centrosymmetric dimmer, and complex 2h adopted a six-coordinate distorted octahedral geometry due to the coordination of two solvent molecules. These complexes activated by alkylaluminum were examined in butadiene polymerization. In combination with AlⁱBu₃, complexes 2a–c exhibited high catalytic activity (73.5%–94.3%) at 20 °C, whereas other complexes exhibited much lower activity. Interestingly, the activity and selectivity of the complexes increased as increasing polymerization temperature. In particular, 2b and 2c displayed both high activity (99% and 80%, respectively) and trans-1,4 selectivity (95.6% and 96.2%, respectively) at 60 °C. The trans-1,4 selectivity of 2b varied as alkylaluminum used as a cocatalyst, in the following order: AlⁱBu₃ > AlOct₃ > AlEt₃ > AlMe₃, whereas much lower trans-1,4 selectivity was observed in the cases of using MAO and MMAO.     

The effect of [(η-C3H5)(η-C5H5)Mo(CO)2] on drying of solvent-borne alkyd paints

Allyl molybdenum complex [(η³-C₃H₅)(η⁵-C₅H₅)Mo(CO)₂] (Mo-A) was examined as a new drier for solvent-borne alkyd binder. The drying activity of pure Mo-A and the of combinations of Mo-A with cobalt(II) 2-ethylhexanoate (Co-Nuodex) was examined using standard methods for measurements of the drying time and hardness development of the alkyd film. The detailed study of the drying process was studied by time-resolved infrared spectroscopy on ethyl linoleate as well as on thin coating of alkyd binder.     

Organic dyes incorporating the cyclopentadithiophene moiety for efficient dye-sensitized solar cells

Three triarylamine organic dyes (XS28-30) containing a cyclopentadithiophene unit as the conjugated bridge have been designed and synthesized for a potential application in dye-sensitized solar cells (DSSCs). Their absorption spectra, electrochemical and photovoltaic properties have been investigated. The incorporation of ethyl-substituted cyclopentadithiophene is highly beneficial to light-harvesting and preventing close π-π aggregation, thus favorably generating high efficiency. For a typical device, a solar energy conversion efficiency (η) of 5.8% based on XS29 was achieved under simulated AM 1.5 solar irradiation (100 mW cm⁻²) with a short-circuit photocurrent density (J_SC) of 14.4 mA cm⁻², an open-circuit voltage (V_OC) of 601 mV, and a fill factor (ff) of 0.68. These results suggest that the functionalized cyclopentadithiophene unit is a promising candidate for DSSCs.     

Synthesis and photovoltaic properties of low-bandgap polymers based on N-arylcarbazole

Low-bandgap poly(2,7-carbazole) derivatives with variable N-substituent of ethyl (PEtCzBT), phenyl (PPhCzBT) and 4-diphenylaminophenyl (PTPACzBT) on the carbazoles, were synthesized through Suzuki coupling reaction. The polymers show excellent solubility in organic solvents (readily soluble in chloroform, THF and toluene etc.), good thermal stability (5% weight loss temperature of more than 417 °C), and electrochemical properties (reversible redox process with narrow bandgap), and deep HOMO energy levels (∼5.1 eV), allowing them promising candidates in the solar cell fabrication. Bulk-heterojunction solar cells with these polymers as electron donor and (6,6)-phenyl-C₇₁-butyric acid methyl ester (PC₇₁BM) as electron acceptor exhibit high V_oc (0.91-0.95 V) and good power conversion efficiency (PCE) of 1.69% for PEtCzTB, 2.01% for PPhCzTB, and 2.42% for PTPACzTB.     

Synthesis of 1,9-bis[glycidyloxypropyl]penta(1′H,1′H,2′H,2′H-perfluoroalkylmethylsiloxane)s and copolymerization with piperazine

A series of 1,9-bis[glycidyloxypropyl]pentasiloxanes (IV-VI) were prepared by the platinum catalyzed hydrosilylation of 1,9-dihydridodecamethylpentasiloxane (I), 1,9-dihydrido-3,5,7-tris(3′,3′,3′-trifluoropropyl)heptamethylpentasiloxane (II), and 1,9-dihydrido-3,5,7-tris(1′H,1′H,2′H,2′H-perfluorooctyl)heptamethylpentasiloxane (III) with allyl glycidyl ether. Subsequently, IV-VI were copolymerized with piperazine to form high molecular weight copoly(carbosiloxane)s (VII-IX). The structures of the 1,9-bis[glycidyloxypropyl]penta-siloxanes (IV-VI) and copoly(carbosiloxane)s (VII-IX) were determined by ¹H, ¹³C, ²⁹Si, and ¹⁹F NMR as well as IR spectroscopy. The molecular weight distributions (M_w/M_n) of VII-IX have been characterized by gel permeation chromatography and their thermal properties measured by differential scanning calorimetry and thermal gravimetric analysis.