共查询到20条相似文献,搜索用时 375 毫秒
1.
新型开关电源控制芯片UC3842基于电流型控制稳压技术原理,外围电路少,使用方便。文中介绍了一种利用UC3842的重频升压电源的设计方法,它克服了以往PWM开关电源开关损耗大、干扰严重的缺点。 相似文献
2.
文章首先对UC3842芯片做了简单的介绍,描述了其在电路中的主要功能。然后对DC-DC直流Boost升压电路的充电过程和放电过程进行了详细介绍。再根据Boost电路基本公式设计了电路中的核心器件——电感,并利用RC振荡电路设定了开关频率以及电路电流和电压等参数。文中设计了电路原理图,并对电路原理图进行了简单介绍。最后给出了电路的测试结果。 相似文献
3.
文中介绍了一种应用于UPS的新型双Boost电路拓扑,可以实现DC/AC单级升压变换。在对主电路拓扑和工作原理进行分析的基础上,采用SPWM调制方法对其进行了软件仿真和硬件实验。实验结果证明,以Boost变换电路可以实现高频功率变换情况下的单级升压逆变输出。 相似文献
4.
提高UC3842控制开关电源精度的方法 总被引:2,自引:0,他引:2
在研制开关电源的工程实践中,为了提高基于UC3842的开关电源的控制精度以降低其电压调整率和负载调整率,对UC3842电压反馈输入端外围电路进行了研究,找到了提高其控制精度的有效且经济的方法.文中分析了影响UC3842控制的开关电源控制精度的关键因素,介绍了常规接法并指出了其存在的问题,以及改进接法和新型改进接法及其工作原理,比较了常规接法、改进接法和新型改进接法的优缺点,最后通过实验室测试证明了新型改进接法更能有效地降低电源电压调整率和负载调整率. 相似文献
5.
单相有源功率因数校正电路的设计与仿真研究 总被引:1,自引:0,他引:1
论述了单相功率因数校正(APFC)的原理和方法,通过采用Boost型DC-DC变换器作为功率级,UC3854芯片控制PWM的占空比,并直接驱动MOSFET,使输入电流跟踪输入电压,以提高功率因数。根据设计目标要求对1.2kW平均电流控制的单相Boost功率因数校正电路的主电路及UC3854外围电路参数进行了设计和计算,使功率因数达到了0.9984,并在Orcad环境下进行仿真研究,取得了理想的效果。文中的设计方法和思路对于中小功率直流电源的APFC设计具有一定的借鉴作用。 相似文献
6.
7.
8.
为解决传统三相单开关功率因数校正器输入电流谐波较大的问题,设计了一种新型拓扑结构的三相单开关升压型PFC(Power Factor Correction)电路。通过在Boost电感和整流桥之间插入合适电容构成二阶滤波器,虽然控制算法不变,但可以在保证功率因数不变的前提下优化输入电流THD(Total Harmonic Distortion)。基于对电路原理的简要分析,建立Matlab仿真模型,再以TMS320F28335为控制核心,搭建Boost PFC 变换器的实验平台。仿真和实验均表明该方案可行,实验电路测试的输入电流THD值小于10%,具有实际应用价值。 相似文献
9.
10.
设计了一种带自适应斜坡补偿的峰值电流模式(PCM)控制Boost变换器。采用一种低功耗自适应斜坡补偿电路,使得升压(Boost)变换器能够实现宽输出范围和高带载能力。在此基础上,提出了一种应用于Boost变换器的电感电流采样电路,该电路实现了高采样速度和高采样精度,且具备全周期的电感电流采样特点。变换器基于SMIC 180 nm BCD CMOS工艺设计。仿真结果表明,该带自适应斜坡补偿的PCM控制Boost变换器输入电压转换范围为2.8 V~5.5 V,输出电压转换范围为4.96 V~36.1 V,最大输出负载电流高达5 A。 相似文献
11.
根据非线性调频函数的调频曲线,拟合出一种新的调频函数曲线,使该函数在定义域内的值及其一、二阶导数与调频S曲线高度一致。据此提出调频函数的假设数学模型,将线性调频信号与非线性调频信号统一起来。采用Matlab软件对该模型的脉压过程进行了仿真,同时对基于该函数的脉压性能进行了分析和讨论。最后,简单介绍了这种信号在空管雷达领域的应用。 相似文献
12.
以家庭网络为背景,从家庭网络的概念及逻辑结构入手,提出了家庭交互控制网络的概念,分析并比较了家庭交互控制网络中分散交互控制方式和集中交互控制方式两种网络参考模型,并基于集中交互控制网络参考模型提出了一种用于改善人机交互界面、并能隔离不同设备交互逻辑的家用无线手持交互设备的功能设计方案,给出了详细的功能分析、人机接口设计及系统功能结构设计,最后对家用手持交互设备与集成家电控制功能的手机之间的关系进行了简要的分析. 相似文献
13.
针对压电叠堆迟滞带来的非线性效应严重制约系统控制精度提升的问题,该文提出了一种基于复合控制的压电驱动器控制方法,对系统非线性误差进行建模补偿,并基于数控芯片实现了嵌入式驱动设计。采用广义PI模型对被控压电促动器进行建模,利用指数函数作为密度函数,并基于粒子群算法对包络函数和密度函数进行参数寻优,最终得到压电促动器的前馈补偿逆模型,结合比例积分控制率实现系统的复合控制。同时采用数字信号处理结合现场可编程门阵列(DSP+FPGA)的数控架构,既保证了逆模型求解过程在DSP中实现的便捷性,又保证了采样及闭环控制在FPGA中实现的实时性及快速性。实验结果证明了所提设计方法的正确性及有效性。 相似文献
14.
利用嵌入在Xilinx FPGA中的PowerPC技术,采用嵌入式可编程片上系统的设计思想,设计了基于现场可编程门阵列(FPGA)的控制器,实现在FPGA中定制完整的实时信号处理设备,方便了信号处理的设计。文中设计的控制器完成对快速傅里叶变换(FFT)、先进先出(FIFO)等模块的各控制信号的控制及对数据收发的控制。通过在总线上挂接自定义IP,增强了片上微机功能,使得设计更具灵活性。通过编制特定的软件代码,利用PowerPC的架构可以方便地控制FFT模块的处理点数。最后对该控制器进行了仿真,并在XUP VirtexⅡ pro实验板上对其功能进行了具体的实现。 相似文献
15.
Haitao Xu Xianwei Zhou Yueyun Chen 《International Journal of Wireless Information Networks》2013,20(4):365-374
This paper proposes a cooperative power control strategy for resource adaptation in mobile network to optimize user uplink transmission power. Our approach is based on a cooperative model using the economic concepts of utility function and the random graph theory. Based on the model, we develop a distributed power control algorithm that maximizes the utilities of all mobile users. Formulating this algorithm as a cooperative strategy, we show the uncertainty and existence of the power control approach with theory of random bipartite graph and utility function. A discussion to the existence of optimal solutions is given. Then a distributed power control scheme is proposed based on the optimal solutions. It is shown by way of simulation that by introducing utility function in the power control algorithm, there is a performance improvement in terms of the utilities that mobile users obtained. Numerical results are presented for the algorithm. 相似文献
16.
This paper proposes a closed-form power control function for the reverse link of a multirate single chip-rate variable processing gain DS-CDMA system in a mobile radio environment that assumes a Rayleigh fading channel with log-normal shadowing and path loss. A closed-form open-loop power control function based on a newly defined traffic exponent is proposed, and nonlinear programming is used to perform the optimization. In addition, a user model that allows users to dynamically switch traffic rates for different connection applications is implemented. Results obtained using random chip sequences demonstrate improvement in the system capacity with the new power control function compared to the conventional power control function. Furthermore, the proposed function also simplifies the power control processing 相似文献
17.
Paszke W. Galkowski K. Rogers E. Owens D.H. 《Circuits and Systems II: Express Briefs, IEEE Transactions on》2004,51(11):629-634
This paper deals with the problem of designing a control law for differential linear repetitive processes based on minimizing a cost function in the presence of uncertainties in the process model. This control law results in a closed-loop stable process with an associated cost function which is bounded for all admissible uncertainties. Moreover, an optimization algorithm is developed to design this law such that it minimizes the upperbound of the closed-loop cost function. 相似文献
18.
Neural-network-based predictive learning control of ram velocity in injection molding 总被引:3,自引:0,他引:3
S.N. Huang K.K. Tan T.H. Lee 《IEEE transactions on systems, man and cybernetics. Part C, Applications and reviews》2004,34(3):363-368
In this paper, we develop a predictive learning controller for ram velocity of injection molding based on neural networks. We first introduce a model of describing the injection molding, including the time horizon and the batch index. The feedback control plus biased function is proposed for controlling this plant. More specifically, a radial basis function (RBF) network is used to approximate the biased function based on the time horizon. The weights in the RBF are determined by a predictive control scheme based on the batch index. For this algorithm, relevant convergence is investigated. Simulation results reveal that the proposed control can achieve our claims. 相似文献
19.