回收PET共混物的非等温结晶和熔融行为

采用双螺杆挤出机制备了聚丙烯(PP)/回收聚对苯二甲酸乙二酯(r-PET)、r-PET/马来酸酐接枝PP(PP-g-MAH)和r-PET/甲基丙烯酸缩水甘油酯接枝PP(PP-g-GMA)共混物,并研究了共混物组成、熔融温度与时间以及降温速率对共混物非等温结晶与熔融行为的影响.结果表明,r-PET与PP共混,结晶温度均提高,这与组分间起到异相成核诱导结晶作用有关.r-PET结晶温度随PP-g-MAH用量增加而降低,但受PP-g-GMA用量影响较小;r-PET可提高PP-g-MAH结晶温度,但降低PP-g-GMA结晶温度.熔融温度提高,共混物中PP结晶温度和熔点均降低,r-PET熔融峰形和熔点取决于共混物的熔融温度及界面相互作用.     

增容剂对PP/回收PET共混物性能的影响

采用熔融共混的方法,制备了聚丙烯(PP)/回收聚对苯二甲酸乙二酯(r-PET)共混物,研究了增容剂甲基丙烯酸缩水甘油酯接枝聚丙烯(PP-g-GMA)对共混物力学性能、热稳定性的影响。结果表明:增容剂的加入能提高共混物的拉伸强度和拉伸模量;加入增容剂能显著提高共混物的热分解温度,增容剂使r-PET的熔点降低;增容剂对PP的结晶性能影响与熔融温度有关。     

增容剂对PP/r-PET共混体系结构与性能影响

采用熔融接枝法制备了聚丙烯(PP)接枝甲基丙烯酸缩水甘油酯接枝物(PP-g-GMA)和聚丙烯接枝马来酸酐接枝物(PP-g-MAH),并用PP-g-GMA和PP-g-MAH作为PP/回收聚对苯二甲酸乙二醇酯(PP/r-PET)共混体系(质量份之比100/12)的增容剂。通过对共混体系进行分析,研究了PP-g-GMA和PP-g-MAH对PP/r-PET共混体系结构与性能的影响。结果表明:成功制备了PP-g-GMA和PP-g-MAH;PP-g-GMA的MFR(熔体流动速度)低于PP-g-MAH的;PP-g-GMA质量份为6份时,共混体系的拉伸强度和冲击强度较未增容体系提高了54.8%和21.8%,增强与增韧效果较明显;当PP-g-MAH质量份为6份时,共混体系的拉伸强度提高了52.1%,但冲击强度稍有降低;PP-g-GMA使得r-PET在PP中分布更均匀。     

增容PP/回收PET共混物的力学性能

采用熔融挤出法制备了聚丙烯(PP)/增容剂/回收聚对苯二甲酸乙二酯(r-PET)共混物,研究了r-PET、不同增容剂和混合增容剂对PP/r-PET共混物力学性能的影响.r-PET提高了PP的拉伸强度、弯曲强度及其模量,但降低了冲击强度;采用马来酸酐接枝聚丙烯(PP-g-MAH)增容,可提高PP/r-PET共混物的拉伸强度、弯曲强度及其模量,但使冲击强度稍有降低;马来酸酐接枝乙烯-辛烯共聚物(POE-g-MAH)增容或PP-g-MAH/POE-g-MAH混合增容可提高PP/r-PET共混物的冲击强度,且对共混物的拉伸和弯曲强度影响不大.     

马来酸酐化增容剂对PP/PET共混物性能的影响

采用熔融共混法制备了聚丙烯(PP)/聚对苯二甲酸乙二酯(PET)共混物,研究了马来酸酐接枝聚丙烯(PP-g-MAH)和马来酸酐接枝乙烯/辛烯共聚物(POE-g-MAH)作为增容剂对共混物力学性能和非等温结晶行为的影响。结果表明:PP-g-MAH提高了共混体系的拉伸强度,加入POE-g-MAH则显著提高共混物的断裂伸长率;当PP∶PET∶增容剂质量比为80∶20∶5时,共混体系的力学性能较好;PET起到异相成核的作用,使PP的结晶峰温升高,半结晶时间缩短;加入增容剂,使PP的结晶峰温降低,半结晶时间延长。     

增容剂对PP/PA66共混物力学性能和结晶行为的影响

采用熔融共混法制备了聚丙烯(PP)/聚酰胺66(PA66)共混物,研究了聚丙烯接枝马来酸酐(PP-g-MAH)和乙烯-辛烯共聚物接枝马来酸酐(POE-g-MAH)作为增容剂对PP/PA66共混物力学性能和非等温结晶行为的影响。结果表明:PP-g-MAH提高了共混体系的拉伸强度,加入5份POE-g-MAH能显著提高共混物的断裂伸长率;PA66可起到异相成核作用,使PP的结晶峰温度升高;加入PP-g-MAH进一步提高了PP的结晶峰温度;PA66使PP的结晶活化能增大,增容剂的加入则使共混体系中PP的结晶活化能降低。     

PP-TPEE共混物的结晶性能

采用双螺杆挤出机,制备了聚丙烯(PP)、热塑性聚酯弹性体(TPEE)、聚丙烯接枝甲基丙烯酸缩水甘油酯(PP-g-GMA)共混体系。通过X射线衍射仪(XRD)与差示扫描量热仪(DSC)考察了共混物的结晶行为。XRD分析结果表明:TPEE与PP-g-GMA的加入使PP的晶面参数发生变化,晶面间距增大。DSC测试结果表明:TPEE的加入使得共混物的热结晶温度升高、结晶度降低;随着PP-g-GMA含量的增加,共混物的结晶度进一步减小;随DSC测试降温速率的增大,纯PP与PP-TPEE共混物的热结晶温度向低温方向移动。     

PP/POE/nano-SiO_2复合材料反应性增容的研究

采用反应性增容的方法,通过熔融共混制备聚丙烯/乙烯-辛烯共聚物/纳米二氧化硅(PP/POE/nano-SiO2)三元复合材料。研究了加入反应性增容剂聚丙烯与甲基丙烯酸缩水甘油酯接枝物(PP-g-GMA)后复合材料的力学性能、结晶性能及加工性能。结果表明:PP-g-GMA与氨基化改性纳米二氧化硅(NH2-SiO2)发生开环反应,能够增强基体树脂PP与nano-SiO2的界面作用和相容性,使nano-SiO2均匀分散于PP中,有助于PP的异相成核。当PP/PP-g-GMA/POE/NH2-SiO2质量比为70/10/20/2时,冲击强度达到52.9 kJ/m2,弯曲强度达到53.24 MPa;与纯PP和PP/POE(80/20)相比,力学性能得到了明显的提高,球晶尺寸明显减小。     

PAG原位增容PP/PA6共混物的非等温结晶动力学

用差示扫描量热法研究了聚丙烯（PP）、聚酰胺6(PA6)以及用α-甲基苯乙烯（AMS）和甲基丙烯酸缩水甘油酯(GMA)的低相对分子质量共聚物(PAG)原位增容的PP/PA6共混物的非等温结晶动力学,采用修正Avrami方程的Jeziorny法对所得数据进行了处理。结果表明,与对比样PP/PA6相比,加入增容剂PAG后,共混体系中PP和PA6两相的结晶峰温Tp和结晶热焓 H均有所降低,而半结晶时间t1/2则有所延长,表明PAG的加入使共混体系两相大分子链的活动性受到了阻碍,导致其结晶困难;在2.5～40.0 ℃/min的降温速率范围内,修正的Avrami模型能很好地描述PP、PA6、PP/PA6及PAG增容PP/PA6共混物的非等温结晶过程。     

PTT/PP共混物的性能研究

通过熔融共混制备了聚对苯二甲酸丙二酯/聚丙烯(PTT/PP=75/25)及其马来酸酐接枝PP(PP-g-MAH)增容共混物,研究了PTT/PP及其增容共混物的结晶性能、力学性能、流变性能和结晶形态。研究结果表明,PTT与PP共混能提高PP、PTT组分的结晶温度;对于增容共混物,随PP-g-MAH用量的增加,PP和PTT的结晶温度基本不变。加入PP使PTT拉伸强度降低,冲击强度提高;PP-g-MAH增容使共混物的拉伸和冲击强度都提高。增容共混物的熔体粘度明显降低,存在明显的剪切变稀现象,但熔体粘度与PP-g-MAH用量无关。在一定用量范围内,随PP-g-MAH用量的增加,PP分散相的尺寸变小。     

Effects of the compatibilizer PP-g-GMA on morphology and mechanical properties of PP/PC blends

Effects of the compatibilizer polypropylene grafted with glycidyl methacrylate(PP-g-GMA) on the morphology, thermal, rheological and mechanical properties of polypropylene and polycarbonate blends (PP/PC) were studied. It was found that the addition of PP-g-GMA significantly changed their morphology. The mean size of domains reduced from 20 μm to less than 5 μm. The dispersed domain size is also strongly dependent upon the content of PP-g-GMA. The interfacial tension of PP/PC/PP-g-GMA (50/30/20) is only about one-tenth of PP/PC (70/30). The crystallization temperature of PP in PP/PC/PP-g-GMA is 5–8°C higher than that of PP in PP/PC blends. Characterization studies based on mechanical properties, differential scanning calorimetry, rheology and morphological evidence obtained by using scanning electron microscopy support the hypothesis that an in-situ copolymer PP-g-PC was formed during the blending process.     

Crystallization behavior and spherulite growth rate of isotactic polypropylene in isotactic polypropylene/natural rubber based thermoplastic elastomers

The melting and crystallization behavior of isotactic polypropylene/natural rubber (PP/NR) based thermoplastic elastomers (TPEs) were investigated using differential scanning calorimetry. The samples were scanned at a heating rate of 10°C/min under nitrogen atmosphere. The effects of blend ratio on the melting and crystallization characteristics of the blends were analyzed. Normalized crystallinity is unchanged by the addition of small amount of NR, but as the amount of rubber increases crystallinity increased for the 30/70 NR/PP and lowered for the 50/50 NR/PP blend system. Morphology of the blend was analyzed using scanning electron microscopy (SEM). Blend ratio showed a pronounced influence on the phase morphology of the NR/PP TPEs. As the amount of NR increases more than 50 wt % the system changes from dispersed to cocontinuous structure. Hot‐stage polarizing optical microscopy (POM) was used to study the radial growth of spherulite as a function of blend ratio, cooling rate, and crystallization temperature. Spherulite growth rate is marginally influenced by the rubber inclusions. The spherulite morphology observed under polarized optical microscopy is influenced by the blend morphology. It was found that for the cocontinuous 50/50 blend system, spherulites are much different from the usual appearance under polarized light. Attempts have been made to correlate the crystallization behavior with the morphology of the blend. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Studies on simultaneous crystallization of polypropylene/nylon 12 blends

The effect of the morphology of polypropylene (PP)/nylon 12 (PA12) blends on their crystallization behaviour is studied using differential scanning calorimetry and scanning electron microscopy. In PP/ maleated polypropylene (PP-MA)/PA12=65/10/25 blend, simultaneous phase (PA12) is smaller than 0.5 μm, PP crystallizes first and its crystals induce the crystallization of PA12. When some of the PA12 particles are larger than 0.5 μm, this part of PA12 crystallizes first. Then this part of the PA12 crystals induces the crystallization of PP, and PP crystals induced the crystallization of PA12 fine droplets in turn.     

增容剂对PP/PET原位微纤化共混物的影响

通过"熔融挤出-热拉伸-淬冷"的方法制备了原位微纤化共混物。采用扫描电镜、差示扫描量热仪和力学性能测试等方法研究了增容剂PP-g-GMA含量对共混物微观形态、力学性能和结晶性能的影响。结果表明,增容剂的加入可明显提高两相相容性,改善界面效果,明显降低拉伸前初始粒子的尺寸,但同时使拉伸后形成的微纤呈现一定的损坏,长径比有所降低。增容剂可以明显改善微纤化共混物力学性能,当其含量为2 %（质量分数,下同）时拉伸强度比未增容试样提高了11.0 %,弯曲强度都提高了11.3 %;当其含量为6 %时冲击强度也比未增容共混物提高了34.5 %。此外,PET微纤对PP有很好的异相成核作用,使其结晶温度提高了16.3 ℃,结晶时间为纯PP的32 %左右,而增容剂的加入使共混物中PP的结晶时间延长。     

PET/PP共混体系的熔融及非等温结晶行为

用熔融共混法制备了聚对苯二甲酸乙二醇酯(PET)/聚丙烯(PP)复合材料。对复合体系的形态结构、熔融及非等温结晶行为进行了研究。结果表明:两相界面或PP相对PET结晶无明显的异相成核效应;当PP为连续相时,已结晶的极性PET粒子对PP的异相成核作用较为明显;而当PP为分散相时,固态的PET在一定程度上阻碍了PP分子链的运动,促使PP结晶均相成核趋势增加。与纯PET或PP相比,共混体系中两组分结晶的完善程度都有所下降。     

Study on the Crystallization Properties of Polypropylene/Montmorillonite Composites

The crystalline size of polypropylene (PP) filled with montmorillonite (MMT) was studied by X-ray diffraction (XRD). The isothermal crystallization behavior of polypropylene was studied by means of differential scanning calorimetry (DSC). The Avrami equation was used to describe the isothermal crystalline kinetics of PP/MMT composites. The result showed that the addition of MMT decreased the crystalline size L _hkl of the polymer. MMT was used as nucleating agent during isothermal crystallization process of polypropylene. The addition of montmorillonite decreased the crystallization time of the polypropylene and the melt point was raised. The value of Avrami exponent n was related with the crystallization temperature. The value of Avrami pre-index factor k of PP/MMT composite was decreased with increasing crystallization temperature. The value of half crystallization time t _1/2 of PP/MMT composite was less than that of PP at a given crystallization temperature, signifying that montmorillonite acted as nucleating agent, accelerated the overall crystallization process.