Synthesis and photoresponsive behavior of the high-Tg azobenzene polymers via RAFT polymerization

Well-defined photo-responsive alternating copolymers, poly(4-(N-maleimido)azobenzene-alt-styrene)s (PMSts), were successfully synthesized via reversible addition–fragmentation chain transfer (RAFT) polymerization. A divinyl monomer was used in this polymerization to prepare high molecular weight azobenzene polymers. These polymers had good solubility in most organic solvents, formed films well, and had high glass transition temperatures (T_g = 174–250 °C) and were heat resistant (T_d > 320 °C). The photo-induced trans–cis isomerization of the copolymers was examined in chloroform solution. Surface-relief-gratings (SRGs) formed on the polymer films were also investigated using illumination from a linearly polarized Kr⁺ laser beam.     

Effects of oxidation cross-linking and sintering additives (TiN,B) on the formation and heat-resistant performance of polymer-derived SiC(Ti,B) films

Effects of oxidation cross-linking and sintering additives (TiN, B) on the microstructure formation and heat-resistant performance of freestanding SiC(Ti, B) films synthesized from Ti, B-containing polycarbosilane (TiB-PCS) precursor were investigated. TiB-PCS green films were first cross-linked for 1 h, 2 h, 3 h and 4 h, respectively, and then pre-sintered at 950 °C. Finally, they were sintered at 1800 °C to complete the conversion from organic films to inorganic SiC(Ti, B) films. The results reveal that curing time has a great impact on the uniformity and density of SiC(Ti, B) films. TiB-PCS films cured for 3 h yield the best quality SiC(Ti, B) films, which are composed of β-SiC crystals, C clusters, α-SiC nano-crystals, a small amount of TiB₂ and B₄C. TiB₂ and B₄C are both steady phases which can inhibit abnormal growth of β-SiC, effectively reduce sintering temperature and help consume excess C from decomposition of amorphous SiOxCy. After high temperature annealing at 1500 °C, 1600 °C and 1700 °C in argon, SiC(Ti, B) films still keep excellent mechanical properties, which makes them attractive candidate materials for microelectromechanical systems (MEMS) used at ultra-high temperatures (exceeding 1500 °C).     

Synthesis and characterization of a cross-linkable nonlinear optical polymer functionalized with a thiophene- and tricyanovinyl-containing chromophore

This paper reports a novel nonlinear optical polymer BP-AVT-TCV functionalized with a thiophene- and tricyanovinyl-substituted chromophore. BP-AVT-TCV was synthesized by the post-tricyanovinylation of an epoxy-based precursor polymer BP-AVT, and had a high molar functionalization degree of chromophore (70 mol.%). It had an enhanced glass transition temperature (T_g = 164 °C) compared with BP-AVT (T_g = 114 °C), and a high decomposition temperature (T_d,5% = 295 °C). BP-AVT-TCV was further cross-linked to achieve the three-dimensional (3D) network of thermosetting polyurethane (PU). The poled PU films revealed an electro-optic (EO) coefficient (γ₃₃) value of 21 pm/V at a wavelength of 1315 nm. The structures of the polymers were confirmed by FT-IR, UV–Vis, and ¹H NMR spectra.     

Charge–discharge curves and discharge capacities of LiNi1−yCoyO2 synthesized from lithium carbonate and nickel and cobalt oxides

LiNi_1?yCo_yO₂ (y=0.1, 0.3, and 0.5) were synthesized by a solid-state reaction method at 800 °C and 850 °C using Li₂CO₃, NiO, and Co₃O₄ as the starting materials. The electrochemical properties of the synthesized LiNi_1?yCo_yO₂ were then investigated. For samples with the same composition, the particles synthesized at 850 °C were larger than those synthesized at 800 °C. The particles of all the samples synthesized at 850 °C were larger than those synthesized at 800 °C. LiNi_0.5Co_0.5O₂ synthesized at 850 °C had the largest first discharge capacity (159 mA h/g), followed in order by LiNi_0.7Co_0.3O₂ synthesized at 800 °C (158 mA h/g) and LiNi_0.9Co_0.1O₂ synthesized at 850 °C (151 mA h/g). LiNi_0.9Co_0.1O₂ synthesized at 850 °C had the best cycling performance with discharge capacities of 151 mA h/g at n=1 and 156 mA h/g at n=5.     

Synthesis of lithium LiNi1−yCoyO2 from lithium carbonate,nickel oxide and cobalt carbonate and their electrochemical properties

LiNi_1?yCo_yO₂ (y = 0.1, 0.3 and 0.5) were synthesized by solid state reaction method at 800 °C and 850 °C from Li₂CO₃, NiO and CoCO₃ as starting materials. The electrochemical properties of the synthesized LiNi_1?yCo_yO₂ were investigated. As the content of Co decreases, particle size decreases rapidly and particle size gets more homogeneous. When the particle size is compared at the same composition, the particles synthesized at 850 °C are larger than those synthesized at 800 °C. Among LiNi_1?yCo_yO₂ (y = 0.1, 0.3 and 0.5) synthesized at 850 °C, LiNi_0.7Co_0.3O₂ has the largest intercalated and deintercalated Li quantity Δx at the first charge–discharge cycle, followed in order by LiNi_0.9Co_0.1O₂ and LiNi_0.5Co_0.5O₂. LiNi_0.7Co_0.3O₂ synthesized at 850 °C has the largest first discharge capacity (142 mAh/g), followed in order by LiNi_0.9Co_0.1O₂ synthesized at 850 °C (113 mAh/g), and LiNi_0.5Co_0.5O₂ synthesized at 800 °C (109 mAh/g).     

Anode-supported SOFCs based on Sm0.2Ce0.8O2−δ electrolyte thin-films fabricated by co-pressing using microwave combustion synthesized powders

Decreasing the electrolyte thickness is an effective approach to improve solid oxide fuel cells (SOFCs) performance for intermediate-temperature applications. Sm_0.2Ce_0.8O_2−δ (SDC) powders with low apparent density of 32±0.3 mg cm⁻³ are synthesized by microwave combustion method, and SDC electrolyte films as thin as ~10 μm are fabricated by co-pressing the powders onto a porous NiO–SDC anode substrate. Dense SDC electrolyte thin films with grain size of 300–800 nm are achieved at a low co-firing temperature of 1200 °C. Single cells based on SDC thin films show peak power densities of 0.86 W cm⁻² at 650 °C using 3 vol% humidified H₂ as fuel and ambient air as oxidant. Both the thin thickness of electrolyte films and ultra-fine grained anode structure make contributions to the improved cell performance.     

The effects of the post-annealing time on the growth mechanism of Bi2Sr2Ca1Cu2O8+∂ thin films produced on MgO (100) single crystal substrates by pulsed laser deposition (PLD)

Bi₂Sr₂Ca₁Cu₂O_8+∂ thin films were deposited on MgO (100) substrates by pulsed laser deposition (PLD). The effects of post-annealing time on the phase formation, the structural and superconducting properties of the films have been investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature dependent resistivity (R–T), atomic force microscopy (AFM), and DC magnetization measurements. The films deposited at 600 °C were post-annealed in an atmosphere of a gas mixture of Ar (93%) and O₂ (7%), at 860 °C for 10, 30, and 60 min. All films have demonstrated a mainly single phase of 2212 with a high crystallinity (FWHM≈0.159°) and c-axis oriented. The critical temperature, T_C, of the films annealed for 10, 30, and 60 min were obtained as 77, 78, and 78 K, respectively. The highest critical current density, J_C, was calculated as 3.34×10⁷ A/cm² for the film annealed at 860 °C for 30 min at 10 K.     

Glass-forming hole-transporting carbazole-based hydrazone monomers,polymers, and twin compounds

The synthesis, optical, thermal, and photoelectrical properties of new carbazole-based hydrazone monomers, polymers, and twin compounds are reported. All the synthesized materials are capable of glass formation. Their glass transition temperatures range from 27 to 90 °C. The ionization potentials of the films of carbazole-based hydrazones measured by the electron photoemission technique range from 5.18 to 5.48 eV. Hole-drift mobilities in the amorphous films of the synthesized hydrazone monomers measured by the time-of-flight technique at room temperature reach 10^?4 cm²/(V s) at high applied electric fields.     

The effects of deposition temperature on structure and dielectric properties of Ba0.6Sr0.4TiO3 thin films produced by pulsed laser deposition

The effects of deposition temperature on orientation, surface morphology and dielectric properties of the thin films for Ba_0.6Sr_0.4TiO₃ thin films deposited on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition were investigated. X-ray diffraction patterns revealed a (2 1 0) preferred orientation for all the films. With rising substrate temperature from 650 °C to 700 °C, the crystallinity and crystal grain size of the films increase, the relative dielectric constant increases, but the dielectric losses have not obvious difference. The film deposited at 350 °C and annealed at 700 °C has strongly improved roughness and dielectric permittivity compared with the film only deposited directly at 700 °C. Three distinct relaxation processes within tan(δ) were found for the Ba_xSr_1?xTiO₃ film: a broadened process of the film relaxation, an intermediate peak which originates from Maxwell–Wagner–Sillars polarization, and an extremely slow process ascribed to leak current. The complex dielectric permittivity and loss can be fitted by an improved Cole–Cole model corresponding to a stretched relaxation function.     

Plasma-sprayed La2Ce2O7 thermal barrier coatings against calcium–magnesium–alumina–silicate penetration

As one of promising thermal barrier coating (TBC) candidates, La₂Ce₂O₇ (LC) has attracted increasing attention because of its low thermal conductivity and potential capability to be operated above 1250 °C. In this paper, the microstructure evolution and mechanical properties of the plasma-sprayed LC TBC with calcium–magnesium–alumina–silicate (CMAS) glassy deposits at 1250 °C were investigated. Due to chemical reaction between the CMAS deposits and LC coating, a dense sealing layer, mainly composed of Ca₂(La_xCe_1−x)₈(SiO₄)₆O_6−4x and CeO₂, was formed on the coating after heat-treatment at 1250 °C and effectively prevented CMAS from further penetration. The interaction layer had the micro-hardness of ∼10–12 GPa, relatively harder than the LC coating.     

Synthesis and characterization of new fluorescent polyimides bearing 1,2,4-triazole and 1,2-diaryl quinoxaline: Study properties and application to the extraction/elimination of metallic ions from aqueous media

In this article, synthesis and characterization of triazole-based polyimides for solid-phase extraction of metal cations is described. For this purpose, new aromatic diamines containing 1,2,4-triazole and substituted 1,2-diaryl quinoxaline units were synthesized and used in polycondensation reaction with aromatic dianhydrates to yield poly(triazole-imide)s (PTAI)s. These polymers had inherent viscosities in the range of 0.58–0.62 dL/g and were readily soluble in a variety of organic solvents; they formed low-colored and tough thin films via solution casting. The PTAIs exhibited T_g between 280 and 338 °C, and their 10% weight loss temperatures were in excess of 540 °C with up to 76% char yield at 700 °C in N₂. These polymers emitted green or blue fluorescence in dilute NMP solution and in the solid state. The triazole groups in the polymer chain were efficient chelating/host units for heavy metal ions. One of these polymers, PTAI(1b), was investigated for its extraction capability for environmentally deleterious metal ions such as Cr^VI, Cr^III, Co^II, Zn^II, Pb^II, Cd^II, Hg^II and Mn^II from aqueous solutions either individually or in the mixture and at different pH values.     

Microwave dielectric properties of the (BaxSr1−x)TiO3 thin films on alumina substrate

Barium strontium titanate, (Ba_xSr_1?x)TiO₃ (BST) thin films have been prepared on alumina substrate by sol–gel technique. The X-ray patterns analysis indicated that the thin films are perovskite and polycrystalline structure. The interdigital electrode with 140 nm thickness Au/Ti was fabricated on the film with the finger length of 80 μm, width of 10 μm and gaps of 5 μm. The temperature dependence of dielectric constant of the BST thin films in the range from ?50 °C to 50 °C was measured at 1 MHz. The dielectric properties of the BST thin films were measured by HP 8510C vector network analyzer from 50 MHz to 20 GHz.     

Examining structure property relationships in coatings based on substituted linear aromatic polycyanurates

Three series of halogenated and non-halogenated polycyanurates are prepared in good yield and purity, and fully characterised. Many of the resulting polymers, formed at room temperature using phase transfer catalysis, can be cast into films with good resilience and high thermal stability (some examples suffer no mass loss when held isothermally at 190 °C and only display appreciable losses when held continuously at 300 °C). Char yields of 35–65% are achieved in nitrogen depending on backbone structure. Some problems were encountered with solubility, particularly with heavily halogenated dichlorotriazines, which limited molecular weights (M_n = 2000–4000 g mol^?1 depending on backbone structure) although when the phase volume ratio was altered to 0.25 higher molecular weights (M_n = 10,000–30,000 g mol^?1) were possible. Best solubility was achieved by using aromatic diols with at least two equivalent phenylene units per dichlorotriazine unit. DSC reveals polymerisation exotherms with maxima at 190–260 °C (ΔH_p = 35–57 kJ/mol) followed by embrittlement and shrinkage (when heated to 300 °C). These phenomena may be due to the formation of poorly formed crystallites (activation energies span 155–380 kJ/mol) combined with thermal isomerisation.     

Ultradrawing above the static melting temperature of ultra-high molecular weight isotactic poly(1-butene) having low ductility in the crystalline state

Ultra-high molecular weight isotactic poly(1-butene) (UHMW-PB1) melt-grown crystal (MGC) films were drawn using the PIN drawing technique. Although the UHMW-PB1 MGC films had poor ductility in the crystalline state, they were ultradrawable in the molten state above the static melting temperature (T_m). The drawability of the MGC films was strongly influenced by the draw temperature, the sample thickness, and the contact time between the metal heater and sample, and it increased with decreasing sample thickness. The maximum draw ratio (DR_max) was nearly constant when the sample thickness was less than 100 μm at a given draw temperature. The contact time between the metal heater and sample needed to draw continuously in the molten state was at least 0.1 s. The ductility increased rapidly above 130 °C, reaching a maximum at 200 °C, and decreased at higher temperatures. A DR_max of 170 was achieved at 200 °C under optimum conditions. The efficiency of the drawing, based on the Herman crystalline orientation function (f_c) and tensile properties versus DR, was lower for films drawn at higher temperatures. The highest f_c of 0.996, tensile modulus of 14 GPa, and strength of 900 MPa were obtained by ultradrawing with DR = 50 at 155 °C. This modulus corresponded to 58% of the X-ray crystal modulus (24 GPa), whereas the modulus of PB1 films drawn in the crystalline state corresponded to only 12–13% (3 GPa) of the theoretical crystal modulus.     

Continuous synthesis of lithium iron phosphate (LiFePO4) nanoparticles in supercritical water: Effect of mixing tee

Continuous supercritical hydrothermal synthesis of olivine (LiFePO₄) nanoparticles was carried out using mixing tees of three different geometries; a 90° tee (a conventional Swagelok^® T-union), a 50° tee, and a swirling tee. The effects of mixing tee geometry and flow rates on the properties of the synthesized LiFePO₄, including particle size, surface area, crystalline structure, morphology, and electrochemical performance, were examined. It was found that, when the flow rate increased, the particle size decreased; however, the discharge capacity of the particles synthesized at the high flow rate was lower due to the enhanced formation of Fe³⁺ impurities. The use of a swirling tee led to smaller-sized LiFePO₄ particles with fewer impurities. As a result, a higher discharge capacity was observed with particles synthesized with a swirling tee when compared with discharge capacities of those synthesized using the 90° and 50° tees. After carbon coating, the order of initial discharge capacity of LiFePO₄ at a current density of 17 mA/g (0.1C) and at 25 °C was swirling tee (149 mAh/g) > 50° tee (141 mAh/g) > 90° tee (135 mAh/g). The carbon-coated LiFePO₄ synthesized using the swirling tee delivered 85 mAh/g at 20C-rate and at 55 °C.     

Microstructure and dielectric properties of the Ti-rich BaO–TiO2 thin films for microwave devices

Ti-rich BaO–TiO₂ thin films were grown on a Pt/Ti/SiO₂/Si substrate using rf sputtering and the structural and dielectric properties of the films were investigated. For the film grown at room temperature and rapidly thermal annealed (RTA) at 900 °C for 3 min, an amorphous phase with a small BaTi₅O₁₃ crystalline phase was formed. As the growth temperature increased, the amount of the BaTi₅O₁₁ crystalline phase increased. For the film grown at 350 °C and RTA at 900 °C for 3 min, the homogeneous BaTi₅O₁₁ phase was formed. The BaTi₄O₉ phase was developed when the growth temperature exceeded 450 °C. The thin film with the homogeneous BaTi₄O₉ phase was obtained when the film was grown at 550 °C and RTA at 900 °C for 3 min. The dielectric properties of the films were measured at 1–6 GHz range. The dielectric constant (ϵ_r) of the BaTi₅O₁₁ film was about 33 and the dissipation factor was about 0.01. The ϵ_r and the dissipation factor of the BaTi₄O₉ film were about 37 and 0.005, respectively.     

Thermal shock resistance of magnesia–chrome refractories—experimental and criterial evaluation

Eleven commercially available magnesia–chrome refractories have been tested. Their basic properties have been determined along with bending strengths at 20,950 and 1400 °C, linear thermal expansion coefficients at 950 °C and 1400 °C, Young's modulus by the static method and the work of fracture at 950 °C. Young's modulus was determined within the temperature range 20–1000 °C, in the process of heating and cooling. The values of thermal shock resistance R_st and R₄ were calculated and correlated to thermal shock resistance (TSR). It has been demonstrated that the R_st criterion is a useful tool to forecast TSR, no matter whether the value of the E modulus is determined by the static or dynamic method. The values of Young's modulus obtained by various methods at 20 °C and 950 °C have been compared. It has been proven that Young's modulus dependence on temperature is a specific feature of a given material.     

Machinability of Ti3SiC2 with layered structure synthesized by hot pressing mixture of TiCx and Si powder

Nanolaminate Ti₃SiC₂ was synthesized from a mixture of TiC_x (x = 0.67)/Si powder by hot pressing to increase machinability. Ti₃SiC₂ was synthesized at temperatures of 1360 °C and 1420 °C for 90 min under a pressure of 25 MPa. The X-ray diffraction results showed that while mainly Ti₃SiC₂ with some unreacted TiC_x were detected in the synthesized samples at 1360 °C, no phases except Ti₃SiC₂ phases remained in the synthesized samples at 1420 °C. The cutting resistance of Ti₃SiC₂ was measured in terms of the principle, feed, and thrust forces and was compared with that of middle-carbon steel, SM45C. The values of the principal force of the synthesized Ti₃SiC₂ were lower than those of SM45C. After machining, the roughness of the Ti₃SiC₂ was lower than those of SM45C; however, the damage to the tool bit used for the machining of SM45C was less than the damage to those used for the machining of the Ti₃SiC₂.     

Synthesis and identification of organosoluble polyamides bearing a triaryl imidazole pendent: Thermal,photophysical, chemiluminescent,and electrochemical characterization with a modified carbon nanotube electrode

A novel monomer containing a triaryl imidazole pendent group was successfully synthesized by nucleophilic substitution of bisphenol A with 2-(2-chloro-5-nitrophenyl)-4,5-diphenyl-1H-imidazole (I). A series of new polyamides (PAs) with inherent viscosities of 0.95–1.2 dL/g was prepared by direct polycondensation of the diamine with various dicarboxylic acids. These PAs were readily soluble in many organic solvents and gave tough and flexible films by solution casting. These PAs exhibited T_gs between 189 °C and 252 °C, and 10% weight loss temperatures in excess of 400 °C with up to 68% char yield at 600 °C in air. All of the PAs emitted a greenish-yellow light in dilute THF solution, with photoluminescence (PL) quantum yields in the range of 10–25%. The chemiluminescent activity and electrochemical oxidation of the PAs were also investigated.     

Structure and dielectric properties of barium titanate thin films for capacitor applications

BaTiO₃ is a typical ferroelectric material with high relative permittivity and has been used for various applications, such as multilayer ceramic capacitors (MLCCs). With the tendency of miniaturization of MLCCs, the thin films of BaTiO₃ have been required. In this work, BaTiO₃ thin films have been deposited on Pt-coated Si substrates by RF magnetron sputtering under different deposition conditions. The films deposited at the substrate temperature from 550 °C–750 °C show a pure tetragonal perovskite structure. The films deposited at 550 °C–625  °C exhibit (111) preferential orientation, and change to (110) preferential orientation when deposited above 650 °C. The film morphologies vary with working pressure and substrate temperature. The film deposited at 625 °C and 4.5 Pa has the relative permittivity of 630 and the loss tangent of 2% at 10 kHz.