Hybrid fiber amplifiers consisting of cascaded TDFA and EDFA for WDM signals

The detailed gain characteristics of hybrid fiber amplifiers that consist of cascaded thulium-doped fiber amplifiers (TDFAs) and erbium-doped fiber amplifiers (EDFAs) are reported. The experimental results showed that the hybrid amplifiers have gains of over 20 dB with the bandwidth of more than 80 nm in the wavelength range between 1460 and 1560 nm. The low noise figure (NF) below 7 dB was obtained in 1460-1540 nm when placing a TDFA in the first stage followed by an EDFA and in 1480-1560 nm when placing amplifiers in a reversed order. The gain of TDFA and EDFA was optimized for minimizing the gain variation ratio (GVR=(maximumgain-minimumgain)/minimumgain: in the unit of decibels) of the hybrid amplifiers, and it could be minimized to less than 0.4 for the amplifiers that have gain in the wavelength region from 1460 to 1537 nm. The gain-equalization technique was applied, and the hybrid amplifier that had an average gain of 20 dB, a gain excursion of less than 2 dB, an output power of 14.5 dBm, and an NF of less than 7 dB in the 77-nm gain band was achieved.     

Ultrawide-band La-codoped Bi/sub 2/O/sub 3/-based EDFA for L-band DWDM systems

The demonstration of a 253-cm-long lanthanum-codoped Bi/sub 2/O/sub 3/-based erbium-doped fiber which provides gain of greater than 20 dB and noise figure less than 6.7 dB to 142 dense wavelength-division-multiplexing channels simultaneously over an extended wavelength range of 58 nm from 1554 to 1612 nm is reported. The 3-dB (gain of 17-20 dB) bandwidth of the erbium-doped fiber amplifier is 54 nm when it is pumped with 350 mW of 1480-nm light. The power conversion efficiency of the fiber is about 54%.     

基于光纤环形镜的L-波段掺铒光纤放大器增益的提高

提出了一种基于光纤环形镜作为反射器的反射式L-波段掺铒光纤放大器(EDFA)结构。光纤环形镜不但可以反射后向放大自发辐射(ASE)作为二次抽运源，而且还可以反射信号，使信号得到二次放大。当抽运功率为115mW时。在1570～1605nm波长范围内，反射式L-波段掺铒光纤放大器的平坦小信号增益达到29．14dB，与前向抽运方式L-波段掺铒光纤放大器相比(保持平坦性不变)。增益提高了5．33dB。分别输入波长为1580nm和1600nm的信号，反射式L-波段掺铒光纤放大器的饱和输出功率为7．63和7．6dBm．与前向抽运方式L-波段掺铒光纤放大器相比分别提高了2．98和3dB。     

All optical gain-locking in erbium-doped fiber amplifiers usingdouble-pass superfluorescence

All optical gain-locking in an erbium-doped fiber amplifier (EDFA) is demonstrated. A double-pass superfluorescence is created by using a broad-band fiber reflector centered at 1530 nm at the output of the EDFA, to lock the gain at 21 dB. Experiments on an eight-channel wavelength-division-multiplexing system shows promise with gain variation between channels of less than 0.6 dB over the input signal power range. While, gain variation with input signal power is about 0.2 dB for all channels     

Low-noise intelligent cladding-pumped L-band EDFA

We present results on a low-cost cladding-pumped L-band amplifier based on side pumping (GTWave) fiber technology and pumped by a single 980-nm multimode diode. We show that simultaneous noise reduction and transient suppression can be achieved by using gain clamping by a seed signal (/spl lambda/=1564 nm). In the gain-clamping regime, the amplifier exhibits 30-dB gain over 1570-1605-nm spectral band with noise figure below 7 dB. The noise figure can be further reduced to below 5 dB by utilizing a low power single-mode pump at 980 nm. The erbium-doped fiber amplifier is relatively insensitive to input signal variations with power excursions below 0.15 dB for a 10-dB channel add-drop.     

Double-pass L-band EDFA with enhanced noise figure characteristics

A new double-pass long wavelength band erbium-doped fiber amplifier with enhanced noise figure characteristics is demonstrated by adding a short length of forward pumped erbium-doped fiber (EDF) in front of a double-pass amplifier. Compared with the conventional double-pass amplifier, the new amplifier provides noise figure improvement of about 0.8 to 6.0 dB over the flat-gain region from 1568 to 1600 nm. Since the optical circulator prevents the amplified signal and backward amplified spontaneous emission from propagating into the EDF, the population inversion of the input part of the amplifier is hardly affected by the intense lights, therefore, the noise figure could be kept low. The new double-pass system has achieved a flat-gain output at about 33.5 dB, which is 13.5 dB higher than that of the single-pass system with gain variation less than 1.3 dB at the flat-gain region. The noise figure varies from 5.9 to 6.6 dB in this region.     

Erbium-doped fiber amplifier pumped in the 950-1000 nm region

The pump wavelength dependence of the gain of an erbium-doped fiber amplifier pumped in the wavelength region 950-1000 nm is discussed. It is found that efficient gain at 1.557 μm, between 25 and 28 dB for 17 mW of launched pump power, can be obtained for any wavelength pump in the range 965-985 nm. The optimum length of erbium fiber needed is found to vary as a function of pump wavelength. The gain as a function of signal wavelength is also investigated at these pump wavelengths     

An erbium-doped multimode optical fiber amplifier

The authors describe the first experimental study of an erbium-doped multimode fiber amplifier. The focus has been to characterize an intermediate core erbium-doped optical fiber, a fiber that is capable of propagating many guided modes at both the signal and pump wavelengths, and to determine the feasibility of using such an active fiber as a multimode fiber amplifier, by measuring its gain, noise, and pump power requirements. For a 2-m length of a 13-μm-core erbium-doped fiber, the authors measured gain as high as 16 dB at a signal wavelength of 1543 nm, with approximately 100 mW pump power (980 nm). For these same test conditions, the smallest excess noise factor β was 42     

Broad-band erbium-doped fiber amplifier with double-passconfiguration

We demonstrate a broad-band silica-based erbium-doped fiber amplifier (EDFA) with double-pass configuration. The signal gain and noise figure are obtained more than 24 dB and less than 6 dB, respectively, for 1526-1562 nm and 1569-1605 nm. The same signal gain can be achieved with 53% less pump power and 45% shorter erbium-doped fiber length, compared to a conventional parallel type EDFA. Furthermore, the noise figure and power conversion efficiency are improved for the wavelength range     

A high-gain, high-output saturation power erbium-doped fiberamplifier pumped at 532 nm

An erbium-doped fiber amplifier with a high small-signal gain of 42 dB at the gain peak of 1536.4 nm, a pumping efficiency of 1.6 dB/mW, and an output saturation power of 10 dBm is obtained with a pump power of 60 mW at 532 nm using the second harmonic of a Nd:YAG laser as the pump source. These experimental results indicate that diode-laser-pumped mini-Nd:YAG lasers with intracavity frequency-doubling have an output power at 532 nm of 100-150 mW that can be of great interest for practical system applications using high-gain, high-output-power erbium-doped fiber amplifiers     

Dispersion-compensating Raman/EDFA hybrid amplifier recycling residual Raman pump for efficiency enhancement

We experimentally demonstrate a novel concept of the dispersion-compensating Raman/erbium-doped fiber amplifier hybrid amplifier recycling residual Raman pump for increase of overall power conversion efficiency. The proposed dispersion-compensating hybrid amplifier system has only one pump source for Raman amplification in the dispersion-compensating fiber (DCF) and the residual pump power after the DCF is recycled for secondary signal amplification in an erbium-doped fiber cascaded to the DCF. Using the proposed scheme, we achieve the significant enhancement of both signal gain and effective gain-bandwidth by 15 dB (small signal gain) and 20 nm, respectively, compared to the performance of the Raman-only amplifier.     

S-band single-stage EDFA with 25-dB gain using distributed ASE suppression

We propose a novel compact design for a single-stage S-band erbium-doped fiber amplifier, wherein distributed suppression of C-band amplified spontaneous emission is provided by optimized bend loss in a coaxial core fiber. Simulations show that /spl sim/25-dB unsaturated gain over 30-nm bandwidth (1495-1525) nm is achievable with the designed module, using a nominal pump power of 500 mW. The noise figure of the amplifier varies between 4.5 and 8 dB from 1495 to 1525 nm. By proper designing, we have also ensured that the gain ripple over the entire 30-nm bandwidth is 相似文献   

一种新型低噪声并联C+L波段掺铒光纤放大器

提出并论证了一种新的低噪声系数C+L波段掺铒光纤放大器的结构.在该结构中,利用一个前置放大器以减少噪声系数,并利用一个带有光纤布拉格光栅的双通结构以增加L波段增益,同时减少噪声系数.实验结果表明,新宽带放大器的噪声系数减小了约2 dB,并且在1 525～1 605 nm波长范围内,增益提高到了25 dB以上.     

A 105-nm ultrawide-band gain-flattened amplifier combining C- and L-band dual-core EDFAs in a parallel configuration

A novel structure for ultrawide-band gain-flattened amplifier by combining two pieces of C- and L-band dual-core erbium-doped fibers is reported. This novel amplifier has a flat gain of 15 dB over a wavelength range of 105 nm (1515-1620 nm). The gain variation for the C-band flat gain region (1515-1555 nm) is 1.3 dB, and for the L-band flat gain region (1562-1620 nm) is 1.5 dB. The noise figure varies from 4.5 to 4.8 dB over the whole bandwidth. The structure of the design is simple without the need of additional expensive components.     

Numerical Modeling of S-Band EDFA Based on Distributed Fiber Loss

A numerical model for the analysis and design of S-band erbium-doped fiber amplifiers has been developed. The model is able to accurately predict the amplifier performances by taking into account the amplified spontaneous emission suppression due to the bending, as well as leakage losses of the fiber used as active medium. The model has been validated by comparing numerical and experimental data of bending loss, amplifier gain, and noise figure of an S-band optical amplifier based on a depressed-cladding erbium-doped fiber. A good agreement has been verified by varying fiber bending radius, input signal power, and wavelength. The model has been then applied to the optimization of the amplifier performances for wavelength-division multiplexer applications. The numerical results show that 20–25 dB gain can be achieved over a 25–30 nm range centered in a different part of the S-band from 1460 to 1525 nm, just by changing the bending radius and the length of a depressed-cladding fiber.      

基于光纤环形镜的掺铒光纤放大器增益平坦化

理论和实验上简要分析研究了由两段保偏光纤组成的光纤环形镜的反射谱特性,提出了利用保偏光纤环形镜进行掺铒光纤放大器(EDFA)增益平坦化的方法。应用该方法,在1527～1562nm范围内,EDFA自发辐射谱的不平坦度为±1dB。     

Automatic optical loss compensation with erbium-doped fiberamplifier

The effect of unwanted optical loss varying over 15 dB is automatically offset with an erbium-doped fiber amplifier used in an optical feedback configuration. The loss compensation is possible for signal wavelengths over a 13 nm range centered at about 1550 nm. The system dynamic range for loss fluctuation frequencies is zero to several kilohertz. The proposed loss compensation scheme simultaneously provides an automatic gain control function that stabilizes the gain against slow changes in input signal power or pump power     

Gain clamping in two-stage L-band EDFA using a broadband FBG

A gain-clamped long wavelength band erbium-doped fiber amplifier (L-band EDFA) with an improved gain characteristic is demonstrated by simply adding a broadband conventional band (C-band) fiber Bragg grating (FBG) in a two-stage amplifier system. The FBG reflects backward C-band amplified spontaneous emission (ASE) from the second stage back into the system to clamp the gain. The gain is clamped at about 22.4 dB with a gain variation below 0.4 dB for input signal powers of -40 to -15 dBm. Compared with an unclamped amplifier of similar noise figure values, the small signal gain has improved by 2.4 dB due to the FBG which blocks the backward propagating ASE. At wavelengths from 1570 to 1600 nm, gain of the clamped amplifier varies from 19.4 to 26.7 dB. The corresponding noise figure varies by /spl plusmn/0.35 dB around 5 dB, which is not much different compared to that of the unclamped amplifier.     

基于单个光纤光栅反射技术的高性能L波段EDFA

基于单个光纤光栅反射技术提出一种高性能L波段EDFA。用一个光纤布拉格光栅(FBG)反射EDFA产生的一部分C波段放大自发辐射(ASE)噪声,该部分ASE噪声被重新注入到掺铒光纤中以提高增益效率。用静态均衡器平坦输出的增益谱,在L波段范围内,增益被箝制在25.5dB,增益不平坦度小于0.5dB,噪声指数小于5.5dB,为DWDM系统提供了一项有效的解决方案。     

A novel ASE self-pumping technique for gain-enhanced L-band erbium-doped fiber amplifiers

A novel method of enhancing gain in long-wavelength-band erbium-doped fiber amplifiers is described using the unwanted amplified spontaneous emission (ASE) self-pumping technique. The unwanted ASE from a first stage amplifier is recycled into a second stage amplifier as a secondary pump. Gain improvements in the vicinity of 0.4 and 1.2 dB are obtained in the wavelength range of 1570–1600 nm. This enables support for higher channels in multiwavelength systems with negligible noise figure penalties.