Synthesis,photodegradation, and energy transfer in a series of poly(ethylene terephthalate–co–2,6-naphthalenedicarboxylate) copolymers

Triplet–triplet energy transfer has been shown to occur from poly(ethylene terephthalate) (PET) units to the 2,6-naphthalenedicarboxylate (2,6-ND) monomer units in a series of poly(ethylene terephthalate–co–2,6-naphthalenedicarboxylate) (PET–2,6-ND) copolymers, as filament yarns, by an exchange mechanism at 77°K. The radius of the “quenching sphere” has been calculated to be 19.7 Å, indicating the presence of triplet energy migration. Photostabilization was observed in the copolymer yarns with the concentration of the monomer dimethyl 2,6-naphthalenedicarboxylate (2,6-DMN) at or above 2 mol %; the rate of phototendering in an air atmosphere was shown to decrease from 2.0 × 10^?19% breaking strength loss/quantum absorbed/cm² in the homopolymer PET to 0.7 × 10^?19% breaking strength loss/quantum absorbed/cm² in the copolymer yarns. The photophysical processes in the monomers, dimethyl terephthalate and 2,6-DMN, were examined by absorption and luminescence studies. The lowest excited singlet and triplet in both monomers were identified to be the ¹(π, π^*) and ³(π, π^*) states, respectively. The phosphorescence of PET was shown to originate from a ³(π, π^*) state, while the complex fluorescence spectrum may arise from some oriented aggregates in the polymer matrix. In copolymer yarns, only the fluorescence emission from the 2,6-ND monomer units at 380 nm was observed. The phosphorescence spectra of the copolymer yarns showed phosphorescence emissions from the PET and 2,6-ND monomer units; in addition, delayed fluorescence from the 2,6-ND monomer was also observed.     

Synthesis of and photodegradation in a series of poly(ethylene terephthalate)–co–4,4′-sulfonyldibenzoate yarns

Phototendering studies of poly(ethylene terephthalate) homopolymer yarn and a series of poly(ethylene terephthalate–co–4, 4′-sulfonyldibenzoate) copolymer yarns have shown that photosensitized degradation occurs more readily in the copolymers than in the homopolymer. A photo-oxidative mechanism involving the second monomer, dibutyl 4, 4′-sulfonyldibenzoate, has been proposed to account for the photosensitization. The photophysical processes in the second monomer, dibutyl 4, 4′-sulfonyldibenzoate, were studied by absorption and luminescence techniques. The lowest excited singlet and triplet in this compound were identified as the ¹(π, π^*) and ₃(π, π^*) states, respectively. The energy levels in the second monomer have been assigned as follows: ¹S₁ ～ 33,000 cm^?1, ¹S₂ ～ 42,000 cm^?1, and ³T₁ ～ 26,000 cm^?1.     

Photophysical processes and interactions between poly(ethylene terephthalate) and 1-amino-2-(2-methoxyethoxy)-4-hydroxy-9,10-anthraquinone

The effect of 1-amino-2-(2-methoxyethoxy)-4-hydroxy-9,10-anthraquinone (C. I. Disperse Red 59) on the phototendering of poly(ethylene terephthalate) (PET) was assessed. The photophysical processes occurring in the polymer, the dye, and the dyed polymer were determined. The energy and nature of the dye and polymer electronic excited states were assigned on the basis of absorption and luminescence properties. Irradiation failed to produce dye-sensitized phototendering of PET; however, the titanium dioxide delusterant in commercial PET did function as a sensitizer in the presence of moist air. The phototendering of blank-dyed PET yarn was found to obey (pseudo-) zero-order kinetics k = 1.69 × 10^?19 per cent breaking strength loss/quantum absorbed/cm². The dye exhibited fluorescence from a lowest, ～51.5 kcal/mole, singlet charge-transfer (C-T) excited state but did not phosphoresce. The PET possessed a complex fluorescence spectrum attributed to similar ¹(n,π^*)₁ excited states, ～78.1 kcal/mole, while its phosphorescence derives from a proposed ³(π,π^*) state, ～69.8 kcal/mole, populated by intersystem crossing from a ¹(π,π^*) state, ～92.3 kcal/mole. The dyed polymer exhibited a PET-sensitized delayed fluorescence from the dyestuff involving triplet–singlet transfer by a dipole–dipole (Coulumbic) long-range resonance excitation mechanism. The transfer process was characterized by an experimentally determined critical transfer distance, R₀, of approximately 40 Å.     

Infrared dichroism of liquid crystalline terephthalate and biphenyldicarboxylate polyesters

Summary Polarised infrared spectroscopy has been used in the structural elucidation of the liquid crystalline polyesters, poly(2-phenyl-1,4-phenylene terephthalate), poly(2-phenyl-1,4-phenylene-4,4-biphenyldicarboxylate) and the copolyester containing both terephthalate and biphenyldicarboxylate units. Order parameters have been calculated and the dichroic behaviour of the vibrational modes used to give valuable insight into the polymer chain structure.     

Synthesis,Characterization, and Conducting Properties of Poly(thiourea azomethines)

Three new polyazomethines having phenylthiourea groups were synthesized through solution polycondensation of terephthalaldehyde with 4,4′-bis(thiourea)biphenyl ether, 4,4′-bis(thiourea)biphenylmethane, and 4,4′-bis(thiourea)biphenyl sulphone. For comparison purposes, simple polyazomethines were prepared by the polycondensation of terephthalaldehyde with 4,4′-diaminodiphenyl ether, 4,4′-diaminodiphenylmethane, and 4,4′-diaminodiphenyl sulphone. Poly(imine)s having phenylthiourea groups were characterized through IR and ¹H-NMR spectroscopic methods and the thermal stability of the polymers were evaluated through TGA analysis. Conductivity of polyaniline synthesized in aqueous p-toluenesulfonic acid was found to be 3.83 Scm^?1. The conductivity of the polymeric blends with polyaniline dopped with p-toluenesulfonic acid and HCl (20% by weight) were found to be in the range 0.16 × 10^?3 ? 5.7 × 10^?3 Scm^?1.     

Blue‐light‐emitting poly(arylene ethynylenes) containing alternating sequences of biphenylene or fluorenediyl and p‐phenylene moieties linked through triple bonds

Two new poly(arylene ethynylenes) were synthesized by the reaction of 1,4‐diethynyl‐2.5‐dioctylbenzene either with 4,4′‐diiodo‐3,3′‐dimethyl‐1,1′‐biphenyl or 2,7‐diiodo‐9,9‐dioctylfluorene via the Sonogashira reaction, and their photoluminescence (PL) and electroluminescence (EL) properties were studied. The new poly(arylene ethynylenes) were poly[(3,3′‐dimethyl‐1,1′‐biphenyl‐4,4′‐diyl)‐1,2‐ethynediyl‐(2,5‐dioctyl‐1,4‐phenylene)‐1,2‐ethynediyl] (PPEBE) and poly[(9,9‐dioctylfluorene‐2,7‐diyl)‐1,2‐ethynediyl‐(2,5‐dioctyl‐1,4‐phenylene)‐1,2‐ethynediyl] (PPEFE), both of which were blue‐light emitters. PPEBE not only emitted better blue light than PPEFE, but it also performed better in EL than the latter when the light‐emitting diode devices were constructed with the configuration indium–tin oxide/poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonic acid) (50 nm)/polymer (80 nm)/Ca:Al. The device constructed with PPEBE exhibited an external quantum efficiency of 0.29 cd/A and a maximum brightness of about 560 cd/m², with its EL spectrum showing emitting light maxima at λ = 445 and 472 nm. The device with PPEFE exhibited an efficiency of 0.10 cd/A and a maximum brightness of about 270 cd/m², with its EL spectrum showing an emitting light maximum at λ = 473 nm. Hole mobility (μ_h) and electron mobility (μ_e) of the polymers were determined by the time‐of‐flight method. Both polymers showed faster μ_h values. PPEBE revealed a μ_h of 2.0 × 10^?4 cm²/V·s at an electric field of 1.9 × 10⁵ V/cm and a μ_e of 7.0 × 10^?5 cm²/V·s at an electric field of 1.9 × 10⁵ V/cm. In contrast, the mobilities of the both carriers were slower for PPEFE, and its μ_h (8.0 × 10^?6 cm²/V·s at an electric field of 1.7 × 10⁶ V/cm) was 120 times its μ_e (6.5 × 10^?8 cm²/V·s at an electric field of 8.6 × 10⁵ V/cm). The much better balance in the carriers' mobilities appeared to be the major reason for the better device performance of PPEBE than PPEFE. Their highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels were also a little different from each other. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 299–306, 2006     

Synthesis and characterization of novel polyaspartimides derived from 2,2′‐dimethyl‐4,4′‐bis(4‐maleimidophenoxy)biphenyl and various diamines

A novel bismaleimide, 2,2′‐dimethyl‐4,4′‐bis(4‐maleimidophenoxy)biphenyl, containing noncoplanar 2,2′‐dimethylbiphenylene and flexible ether units in the polymer backbone was synthesized from 2,2′‐dimethyl‐4,4′‐bis(4‐aminophenoxy)biphenyl with maleic anhydride. The bismaleimide was reacted with 11 diamines using m‐cresol as a solvent and glacial acetic acid as a catalyst to produce novel polyaspartimides. Polymers were identified by elemental analysis and infrared spectroscopy, and characterized by solubility test, X‐ray diffraction, and thermal analysis (differential scanning calorimetry and thermogravimetric analysis). The inherent viscosities of the polymers varied from 0.22 to 0.48 dL g⁻¹ in concentration of 1.0 g dL⁻¹ of N,N‐dimethylformamide. All polymers are soluble in N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide, dimethylsulfoxide, pyridine, m‐cresol, and tetrahydrofuran. The polymers, except PASI‐4, had moderate glass transition temperature in the range of 188°–226°C and good thermo‐oxidative stability, losing 10% mass in the range of 375°–426°C in air and 357°–415°C in nitrogen. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 279–286, 1999     

Synthesis and characterization of new soluble poly(ester‐imide)s containing noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit

A new diimide–diacid chloride (3) containing a noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit was synthesized by treating 2,2′‐dimethyl‐4,4′‐diamino‐biphenylene with trimellitic anhydride followed by refluxing with thionyl chloride. Various new poly(ester‐imide)s were prepared from 3 with different bisphenols by solution polycondensation in nitrobenzene using pyridine as hydrogen chloride quencher at 170°C. Inherent viscosities of the poly(ester‐imide)s were found to range between 0.31 and 0.35 dL g^?1. All of the poly(ester‐imide)s, except the one containing pendent adamantyl group 5e, exhibited excellent solubility in the following solvents: N,N‐dimethylformamide, tetrahydrofuran, tetrachloroethane, dimethyl sulfoxide, N,N‐dimethylacetamide, N‐methyl‐2‐pyrrolidinone, m‐cresol, o‐chlorophenol, and chloroform. The polymers showed glass‐transition temperatures between 166 and 226°C. The 10% weight loss temperatures of the poly(ester‐imide)s, measured by TGA, were found to be in the range between 415 and 456°C in nitrogen. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2486–2493, 2004     

Synthesis and characterization of sulfonated liquid crystalline polyesters

Liquid crystalline polyesters based on hexanediol, dimethyl 4,4′‐biphenyldicarboxylate, and various levels of dimethyl 5‐sodiosulfoisophthalate (0–20 mol%) were prepared using a conventional melt polymerization process. The presence and quantification of the ionic functionality was surveyed using ¹H NMR spectroscopy. Solution viscosities and corresponding molecular weights decreased when the ionic monomer concentration exceeded a critical value (higher than 3 mol%). Differential scanning calorimetry indicated a maximum in the isotropic transition temperature versus ionic modification at approximately 10 mol%. Dynamic mechanical analysis indicated that the glass transition temperature was suppressed due to ionic association at high concentrations (greater than 3 mol%) of ionic functionality. Polarized light microscopy and wide‐angle X‐ray diffraction were used to identify the smectic liquid crystalline and crystalline phases. © 2002 Society of Chemical Industry     

Synthesis and characterization of novel wholly para‐oriented aromatic polyamide‐hydrazides containing sulfone‐ether linkages

Four novel wholly para‐oriented aromatic polyamide‐hydrazides containing flexibilizing sulfone‐ether linkages in their main chains have been synthesized from 4‐amino‐3‐hydroxy benzhydrazide (4A3HBH) with either 4,4′‐sulfonyldibenzoyl chloride (SDBC), 4,4′‐[sulfonylbis(1,4‐phenylene)dioxy]dibenzoyl chloride (SODBC), 4,4′‐[sulfonylbis(2,6‐dimethyl‐1,4‐phenylene)dioxy]dibenzoyl chloride (4MeSODBC), or 4,4′‐(1,4‐phenylenedioxy)dibenzoyl chloride (ODBC) via a low‐temperature solution polycondensation reaction. A polyamide‐hydrazide without the flexibilizing linkages is also investigated for comparison. It was synthesized from 4A3HBH and terephthaloyl chloride (TCl) by the same synthetic route. The intrinsic viscosities of the polymer ranged from 2.85 to 4.83 dL g^?1 in N,N‐dimethyl acetamide (DMAc) at 30°C and decreased with introducing the flexibilizing linkages into the polymer. All the polymers were soluble in DMAc, N,N‐dimethyl formamide (DMF), and N‐methyl‐2‐pyrrolidone (NMP), and their solutions could be cast into films with good mechanical strengths. Further, they exhibited a great affinity to water sorption. Their solubility and hydrophilicity increased remarkably by introducing the flexibilizing linkages. The polymers could be thermally cyclodehydrated into the corresponding poly(1,3,4‐oxadiazolyl‐benzoxazoles) approximately in the region of 295–470°C either in nitrogen or in air atmospheres. The flexibilizing linkages improve the solubility of the resulting poly(1,3,4‐oxadiazolyl‐benzoxazoles) when compared with poly(1,3,4‐oxadiazolyl‐benzoxazoles) free from these linkages. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Melt polymerization of copoly(ethylene terephthalate–imide)s and thermal properties

Copoly(ethylene terephthalate–imide)s (PETI) were prepared by melt polycondensation of bis(2-hydroxyethyl)terephthalate (BHET) and imide containing oligomer, i.e., 4,4′-bis[(4-carbo-2-hydroxyethoxy)phthalimido]diphenylmethane(BHEI). The apparent rate of poly-condensation reaction was faster than that of homo poly(ethylene terephthalate) (PET) due to the presence of imide units. The PETI copolymers with up to 10 mol % of BHEI unit in the copolymer showed about the same molecular weight and carboxyl end group content as homo PET prepared under similar reaction conditions. The increase in T_g of copolymer was more dependent on molar substitution of BHEI than on substitution of BHEN, reaching 91°C with 8 mol % BHEI units in the copolymer from T_g = 78.9°C of homo PET. In the case of PETN copolymer, 32 mol % of bis(2-Hydroxyethyl)naphthalate (BHEN) units gave T_g of 90°C. The maximum decomposition temperature of PETI copolymer was about the same as that of homo PET by TGA analysis. The char yield at 800°C was higher than that of homo PET. © 1996 John Wiley & Sons, Inc.     

Effect of linear comonomers on the rate of crystallization of copolyesters

Small amounts of dimethyl‐4,4′‐biphenyldicarboxylate, 2,7‐dimethyl‐4,5,9,10‐tetrahydropyrenedicarboxylate, and dimethyl‐2,7‐pyrenedicarboxylate have been copolymerized into poly(ethylene) terephthalate (PET). The thermal transitions of the copolymers have been characterized, and the crystallization rates have been measured isothermally. Avrami analysis indicates that all the copolymers crystallized at a slower rate than that of the PET homopolymer. Addition of perylene to the copolymers containing pyrene enhanced the rate of crystallization, which could be the consequence of stacked arene assemblies serving as templates for crystal formation. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2696–2704, 2001     

Synthesis and characterization of novel aromatic polyamides derived from 2,2′‐bis(p‐phenoxyphenyl)‐4, 4′‐diaminodiphenyl ether

BACKGROUND: Wholly aromatic polyamides (aramids) are high‐performance polymeric materials with outstanding heat resistance and excellent chemical stabilities due to chain stiffness and intermolecular hydrogen bonding of amide groups. Synthesis of structurally well‐designed monomers is an effective strategy to prepare modified forms of these aramids to overcome lack of organo‐solubility and processability limitations. RESULTS: A novel class of wholly aromatic polyamides was prepared from a new diamine, namely 2,2′‐bis(p‐phenoxyphenyl)‐4,4′‐diaminodiphenyl ether (PPAPE), and two simple aromatic dicarboxylic acids. Two reference polyamides were also prepared by reacting 4,4′‐diaminodiphenyl ether with the same comonomers under similar conditions. M?_w and M?_n of the resultant polymers were 8.0 × 10⁴ and 5.5 × 10⁴ g mol^?1, respectively. Polymers resulting from PPAPE exhibited a nearly amorphous nature. These polyamides exhibited excellent organo‐solubility in a variety of polar solvents and possessed glass transition temperatures up to 200 °C. The 10% weight loss temperatures of these polymers were found to be up to 500 °C under a nitrogen atmosphere. The polymers obtained from PPAPE could be cast into transparent and flexible films from N,N‐dimethylacetamide solution. CONCLUSION: The results obtained show that the new PPAPE diamine can be considered as a good monomer to enhance the processability of its resultant aromatic polyamides while maintaining their high thermal stability. The observed characteristics of the polyamides obtained make them promising high‐performance polymeric materials. Copyright © 2009 Society of Chemical Industry     

Synthesis of liquid crystalline epoxy and its mechanical and electrical characteristics—curing reaction of LCE with diamines by DSC analysis

An aromatic liquid crystalline epoxy monomer based on biphenyl mesogen was synthesized and cured with three different aromatic diamines. The curing reaction characteristics were analyzed by DSC, and the data were introduced to the Kissinger equation to attain the kinetic parameters. Diglycidyl ether of 4,4′‐biphenyl (DGEBP)/4,4′‐diaminobiphenyl (DABP), and DGEBP/4,4′‐methylenediamine (MDA) systems showed an exotherm curing reaction after comelting of the monomers; the DGEBP/p‐phenylenediamine (PDA) system's curing reaction took place in the solid state without melting of monomers. The activation energy and preexponential factor for the DGEBP/DABP system were 55.6 kJ/mol and 4.0 × 10⁶ min^?1, respectively. Those values for DGEBP/MDA and DGEBP/PDA systems were 55.1 kJ/mol and 1.0 × 10⁶ min^?1 and 148.8 kJ/mol and 7.7 × 10¹⁹ min^?1, respectively. The rate constant at 100°C for DGEBP/PDA is 2 times higher than those for DGEBP/DABP and DGEBP/MDA, which have almost the same values. Strictly speaking, the rate constant of DGEBP/DABP is a little higher than that of DGEBP/MDA, and these results are in good agreement with the DSC curves. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2419–2425, 2002     

Synthesis and characterization of conducting poly(aniline‐co‐diaminodiphenylsulfone) copolymers

Polyaniline, poly(aniline‐co‐4,4′‐diaminodiphenylsulfone), and poly(4,4′‐diaminodiphenylsulfone) were synthesized by ammonium peroxydisulfate oxidation and characterized by a number of techniques, including infrared spectroscopy, ultraviolet–visible absorption spectroscopy, ¹H‐NMR, thermogravimetric analysis, and differential scanning calorimetry. These copolymers had enhanced solubility in common organic solvents in comparison with polyaniline. The conductivities of the HCl‐doped polymers ranged from 1 S cm^?1 for polyaniline to 10^?8 S cm^?1 for poly(4,4′‐diaminodiphenylsulfone). The copolymer compositions showed that block copolymers of 4,4′‐diaminodiphenylsulfone (r₁ > 1) and aniline (r₂ < 1) formed and that the reactivity of 4,4′‐diaminodiphenylsulfone was greater than that of aniline. The results were explained by the effect of the ? SO₂? group present in the polymer structure. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2337–2347, 2003     

Synthesis and properties of sulfonated poly(arylene ether nitrile) copolymers containing carboxyl groups for proton‐exchange membrane materials

A series of sulfonated poly(arylene ether nitrile) copolymers containing carboxyl groups were synthesized via a nucleophilic aromatic substitution reaction from phenolphthalein, hydroquinone sulfonic acid potassium salt, and 2,6‐difluorobenzonitrile in N‐methyl pyrrolidone (NMP) with K₂CO₃ as a catalyst. The synthesized copolymers had good solubility in common polar organic solvents and could be easily processed into membranes from solutions of dimethyl sulfoxide, NMP, N,N′‐dimethyl acetylamide, and dimethylformamide. Typical membranes in acid form were gained, and the chemical structures of these membranes were characterized by Fourier transform infrared analysis. The thermal properties, fluorescence properties, water uptake, ion‐exchange capacity, and proton conductivities of these copolymers were also investigated. The results indicate that they had high glass‐transition temperatures in the range 151–187°C and good thermal stability, with the 10 wt% loss temperatures ranging from 330 to 351°C under nitrogen. The copolymers showed characteristic unimodal ultraviolet–visible (UV–vis) absorption and fluorescence emission, and the UV–vis absorption, fluorescence excitation, and emission peaks of the copolymers were obvious. Moreover, the copolymer membranes showed good water uptake and proton conductivities at room temperature and 55% relative humidity because of the introduction of both sulfonic acid groups and carboxyl groups into the copolymers, whose contents were in ranges 18.45–67.86 and 3.4 × 10^?4 to 3.0 × 10^?3 s/cm, respectively. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40213.     

Synthesis of new poly(amide–imide)s derived from trimellitylimido‐L‐phenylalanine

N‐Trimellitylimido‐L ‐phenylalanine was prepared from the reaction of 1,2,4‐benzenetricarboxylic anhydride with L ‐phenylalanine in N,N‐dimethylformamide solution at refluxing temperature. The direct polycondensation reaction of the monomer imide‐diacid with 4,4′‐diaminodiphenylsulfone, 4,4′‐diaminodiphenylmethane, 1,4‐phenylenediamine, 1,3‐phenylenediamine, 2,4‐diaminotoluene, 4,4′‐diaminodiphenylether and benzidine was carried out in a medium consisting of triphenyl phosphite, N‐methyl‐2‐pyrrolidone, pyridine and calcium chloride. The resulting poly(amide–imide)s, PAIs, having inherent viscosities of 0.21–0.45 dlg^?1 were obtained in high yield. All of the above compounds were fully characterized by IR spectroscopy and elemental analyses. The optical rotation of all PAIs has also been measured. Some structural characterization and physical properties of these new optically active PAIs are reported. © 2001 Society of Chemical Industry     

Aliphatic–aromatic poly(butylene carbonate‐co‐terephthalate) random copolymers: Synthesis,cocrystallization, and composition‐dependent properties

A series of aliphatic–aromatic poly(carbonate‐co‐ester)s poly(butylene carbonate‐co‐terephthalate)s (PBCTs), with weight‐average molecular weight of 113,000 to 146,000 g/mol, were synthesized from dimethyl carbonate, dimethyl terephthalate, and 1,4‐butanediol via a two‐step polycondensation process using tetrabutyl titanate as the catalyst. The PBCTs, being statistically random copolymers, show a single T_g over the entire composition range. The thermal stability of PBCTs strongly depends on the molar composition. Melting temperatures vary from 113 to 213°C for copolymers with butylene terephthalate (BT) unit content higher than 40 mol %. The copolymers have a eutectic melting point when about 10 mol % BT units are included. Crystal lattice structure shifts from the poly(butylene carbonate) to the poly(butylene terephthalate) type crystal phase with increasing BT unit content. DSC and WAXD results indicate that the PBCT copolymers show isodimorphic cocrystallization. The tensile modulus and strength decrease first and then increase according to copolymer composition. The enzymatic degradation of the PBCT copolymers was also studied. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41952.     

Poly(arylene ether)s carrying pendant (3‐sulfonated) phenylsulfonyl groups

A series of poly(arylene ether)s with biphenyl units and pendant sulfonated phenylsulfonyl groups was prepared via nucleophilic aromatic substitution reactions of varying ratios of 3,5‐difluoro‐3′‐sulfonated diphenylsulfone and 4,4′‐difluorodiphenylsulfone with 4,4′‐biphenol. As such, the sulfonic acid moieties reside in the meta position of a pendant, electron‐poor phenylsulfonyl group. Mechanically robust proton‐exchange membranes with ion‐exchange capacities (IEC) ranging from 0.91 to 2.05 meq g^?1 were cast from dimethylacetamide. The thermal stability of the membranes was evaluated via thermogravimetric analysis and the 5% weight losses were found to be in excess of 330 °C in air. The glass transition temperatures were determined, via differential scanning calorimetry, to range from a low of 148 to a high of 209 °C at IEC values of 0.91 and 1.79 meq g^?1, respectively. The copolymer membranes reached proton conductivities as high as 142 mS cm^?1 under 100% relative humidity, with relatively low water uptake values (8–32 wt%). Copyright © 2012 Society of Chemical Industry     

Organosoluble polyimides derived from asymmetric 2‐substituted‐and 2,2′,6‐trisubstituted‐4,4′‐oxydianilines

We report a new method for the preparation of asymmetric diamines using 4,4′‐oxydianiline (4,4′‐ODA) as the starting material. By controlling the equivalents of bromination agent, N‐bromosuccinimide, we were able to attach bromide and phenyl substituents at the 2‐ or 2,2′,6‐positions of 4,4′‐ODA. Thus, four new asymmetric aromatic diamines, 2‐bromo‐4,4′‐oxydianiline (6), 2,2′,6‐tribromo‐4,4′‐oxydianiline (7), 2‐phenyl‐4,4′‐oxydianiline (8) and 2,2′,6‐triphenyl‐4,4′‐oxydianiline (9), were synthesized by this method. Their structural asymmetry was confirmed using ¹H NMR spectroscopy. Asymmetric polyimides (PI10–PI13) were prepared from these diamines and three different dianhydrides (pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 2,2‐bis(3,4‐dicarboxyphenyl)hexafluoropropane dianhydride) in refluxing m‐cresol. The formed polyimides, except PI10a derived from 6 and PMDA, were all soluble in m‐cresol without premature precipitation during polymerization. These polyimides with inherent viscosity of 0.41–0.96 dL g^?1, measured at a concentration of 0.5 g dL^?1 in N‐methyl‐2‐pyrrolidone at 30 °C, can form tough and flexible films. Because of the structural asymmetry, they also exhibited enhanced solubility in organic solvents. Especially, polyimides PI11a and PI13a derived from 7 and 9 with rigid PMDA were soluble in various organic solvents at room temperature. The structural asymmetry of the prepared polyimides was also evidenced from ¹H NMR spectroscopy. In the ¹H NMR spectrum of PI11a, the protons of pyromellitic moiety appeared in an area ratio of 1:2:1 at three different chemical shifts, which were assigned to head‐to‐head, head‐to‐tail and tail‐to‐tail configurations, respectively. These polyimides also exhibited good thermal stability. Their glass transition temperatures ranged from 297 to 344 °C measured using thermal mechanical analysis. © 2013 Society of Chemical Industry