The evaluation of methane mixed reforming reaction in an industrial membrane reformer for hydrogen production

In this work, the performance of an industrial dense PdAg membrane reformer for hydrogen production with methane mixed reforming reaction was evaluated. The rate parameters of mixed reforming reaction on a Ni based catalyst optimized by using the experimental results. One-dimensional models have been considered to model the steam reforming industrial membrane reformer (SRIMR) and mixed reforming industrial membrane reformer (MRIMR). The models are validated by experimental data.The proficiency of MRIMR and SRIMR at similar conditions used as a basis of comparison in terms of temperature, methane conversion, hydrogen yield, syngas production rate and CO₂ flow rate. Results revealed that the methane conversion, hydrogen yield and syngas production rate in MRIMR is considerably higher than SRIMR. Furthermore, the operation temperature of MRIMR could be 195 °C lower than that for SRIMR. This would contribute to a major decrease in process costs as well as a reduction in catalyst sintering. On the other hand, although MRIMR consumes CO₂, the exited CO₂ flow rate at the SRIMR is three times more than that of at the MRIMR, which is a main advantage of MRIMR from the environmental issues point of view.     

Mini CHP based on the electrochemical generator and impeded fluidized bed reactor for methane steam reforming

The paper presents a configuration of mini CHP with the methane reformer and planar solid oxide fuel cell (SOFC) stacks. This mini CHP may produce electricity and superheated steam as well as preheat air and methane for the reformer along with cathode air used in the SOFC stack as an oxidant. Moreover, the mathematical model for this power plant has been created. The thermochemical reactor with impeded fluidized bed for autothermal steam reforming of methane (reformer) considered as the basis for the synthesis gas (syngas) production to fuel SOFC stacks has been studied experimentally as well. A fraction of conversion products has been oxidized by the air fed to the upper region of the impeded fluidized bed in order to carry out the endothermic methane steam reforming in a 1:3 ratio as well as to preheat products of these reactions. Studies have shown that syngas containing 55% of hydrogen could be produced by this reactor. Basic dimensions of the reactor as well as flow rates of air, water and methane for the conversion of methane have been adjusted through mathematical modelling.The paper provides heat balances for the reformer, SOFC stack and waste heat boiler (WHB) intended for generating superheated water steam along with preheating air and methane for the reformer as well as the preheated cathode air. The balances have formed the basis for calculating the following values: the useful product fraction in the reformer; fraction of hydrogen oxidized at SOFC anode; gross electric efficiency; anode temperature; exothermic effect of syngas hydrogen oxidation by air oxygen; excess entropy along with the Gibbs free energy change at standard conditions; electromotive force (EMF) of the fuel cell; specific flow rate of the equivalent fuel for producing electric and heat energy. Calculations have shown that the temperature of hydrogen oxidation products at SOFC anode is 850 °C; gross electric efficiency is 61.0%; EMF of one fuel cell is 0.985 V; fraction of hydrogen oxidized at SOFC anode is 64.6%; specific flow rate of the equivalent fuel for producing electric energy is 0.16 kg of eq.f./(kW·h) while that for heat generation amounts to 44.7 kg of eq.f./(GJ). All specific parameters are in agreement with the results of other studies.     

A numerical study on the active reaction thickness of nickel catalyst layers used in a low-pressure steam methane reforming process

With the advancement of fuel cell technologies and growing interest in the hydrogen economy, the small-scale, distributed production of hydrogen has recently been receiving considerable research attention. The steam methane reforming (SMR) process, an established industrial process for large-scale hydrogen production, can also be successfully deployed for small-scale, low-pressure hydrogen production systems, including compact reformers, microchannel reformers, plate reformers, and monolithic reformers. In this study, the active reaction thickness of nickel catalyst layers was numerically determined by solving one-dimensional reaction/diffusion problems with finite volume method. The small-scale SMR conditions were considered, such as the reforming pressure of 1–3 bar, reforming temperature of 600–800 °C, and steam-to-carbon ratio of 2–4. The results showed the active thickness for the steam reforming and reverse methanation reactions hardly exceeded 0.15 mm for 600 °C, 0.07 mm for 700 °C, and 0.05 mm for 800 °C, at the reforming pressure of 1 bar. Besides, the effects of the volume-specific nickel surface area and diffusion properties were also investigated.     

Simulation of steam reforming of biogas in an industrial reformer for hydrogen production

The paper aims to investigate the steam reforming of biogas in an industrial-scale reformer for hydrogen production. A non-isothermal one dimensional reactor model has been constituted by using mass, momentum and energy balances. The model equations have been solved using MATLAB software. The developed model has been validated with the available modeling studies on industrial steam reforming of methane as well as with the those on lab-scale steam reforming of biogas. It demonstrates excellent agreement with them. Effect of change in biogas compositions on the performance of industrial steam reformer has been investigated in terms of methane conversion, yields of hydrogen and carbon monoxide, product gas compositions, reactor temperature and total pressure. For this, compositions of biogas (CH₄/CO₂ = 40/60 to 80/20), S/C ratio, reformer feed temperature and heat flux have been varied. Preferable feed conditions to the reformer are total molar feed rate of 21 kmol/h, steam to methane ratio of 4.0, temperature of 973 K and pressure of 25 bar. Under these conditions, industrial reformer fed with biogas, provides methane conversion (93.08–85.65%) and hydrogen yield (1.02–2.28), that are close to thermodynamic equilibrium condition.     

Pure hydrogen production in a Pd-Ag multi-membranes module by methane steam reforming

An experimental test campaign has been carried out in order to investigate the performances in terms of pure hydrogen production of a multi-membrane module coupled with a methane reforming fixed bed reactor. The effect of operating parameters such as the temperature, the pressure, the water/methane feed flow rates and the feed molar ratio has been studied. The hydrogen produced into the traditional reformer has been recovered in the shell side of the membrane module by vacuum pumping. The membrane module consists of 19 Pd/Ag permeator tubes of wall thickness 150 μm, diameter 10 mm and length 250 mm: these dense permeators permitted to separate ultra-pure hydrogen.The experiments have been carried out with the reaction pressure of 100-490 kPa, the temperature of the reformer of 570-720 °C and the temperature of the Pd/Ag membranes module of 300-400 °C. A water/methane stream of molar ratio of 4/1 and 5/1 has been fed into the methane reformer at GSHV of 1547.6 and 1796.1 L_(STP) kg⁻¹ h⁻¹. Hydrogen yield value of about 3 has been measured at reaction pressure of 350 kPa, temperature reformer of 720 °C and methane feed flow rate of 6.445 × 10⁻⁴ mol s⁻¹.     

Experimental validation of a pilot membrane reactor for hydrogen production by solar steam reforming of methane at maximum 550 °C using molten salts as heat transfer fluid

An innovative steam reformer for hydrogen production at temperatures lower than 550 °C has been developed in the EU project CoMETHy (Compact Multifuel-Energy To Hydrogen converter). The steam reforming process has been specifically tailored and re-designed to be combined with Concentrating Solar plants using “solar salts”: a low-temperature steam reforming reactor was developed, operating at temperatures up to 550 °C, much lower than the traditional process (usually > 850 °C). This result was obtained after extensive research, going from the development of basic components (catalysts and membranes) to their integration in an innovative membrane reformer heated with molten salts, where both hydrogen production and purification occur in a single stage. The reduction of process temperatures is achieved by applying advanced catalyst systems and hydrogen selective Pd-based membranes. Process heat is supplied by using a low-cost and environmentally friendly binary NaNO₃/KNO₃ liquid mixture (60/40 w/w) as heat transfer fluid; such mixture is commonly used for the same purpose in the concentrating solar industry, so that the process can easily be coupled with concentrating solar power (CSP) plants for the supply of renewable process heat. This paper deals with the successful operation and validation of a pilot scale reactor with a nominal capacity of 2 Nm³/h of pure hydrogen from methane. The plant was operated with molten salt circulation for about 700 h, while continuous operation of the reactor was achieved for about 150 h with several switches of operating conditions such as molten salts inlet temperature, sweep steam flow rate and steam-to-carbon feed ratio. The results obtained show that the membrane reformer allows to achieve twice as high a conversion compared to a conventional reformer operating at thermodynamic equilibrium under the same conditions considered in this paper. A highly pure hydrogen permeate stream was obtained (>99.8%), while the outlet retentate stream had low CO concentration (<2%). No macroscopic signs of reactor performance loss were observed over the experimental operation period.     

Exploring the opportunities for carbon capture in modular,small-scale steam methane reforming: An energetic perspective

Small-scale steam methane reforming units produce more than 12% of all the CO₂-equivalent emissions from hydrogen production and, unlike large-scale units, are usually not integrated with other processes. In this article, the authors examine the hitherto under-explored potential to utilise the excess heat available in the small-scale steam methane reforming process for partial carbon dioxide capture. Reforming temperature has been identified as a critical operating parameter to affect the amount of excess heat available in the steam methane reforming process. Calculations suggest that reforming the natural gas at 850 °C, rather than 750 °C, increases the amount of excess heat available by about 28.4% (at 180 °C) while, sacrificing about 1.62% and 1.09% in the thermal and exergetic efficiency of the process, respectively. Preliminary calculations suggest that this heat could potentially be utilised for partial carbon capture from reformer flue gas, via structured adsorbents, in a compact capture unit. The reforming temperature can be adjusted in order to regulate the amount of excess heat, and thus the carbon capture rate.     

Refuse derived fuel hydrogasification coupled with methane steam reforming

The hydrogasification of Refuse Derived Fuel (RDF) consisting of non-recyclable plastic polymers was combined with methane steam reforming in a “hydrogen self-sustained” loop configuration. The hydrogasification unit fed by 1000 kg/h of RDF was initially modeled by Aspen plus to define best operating conditions, namely temperature, pressure and hydrogen feed flow rate. After the simulations, the temperature of the hydrogasification process has been fixed at 300 °C, the pressure at 10 bar and the hydrogen feed flow rate at 140 kg/h. The steam reforming unit operates at 850 °C while the water-gas shift is conducted at 350 °C. When all the methane produced by hydrogasification is used to feed the steam reformer, which yields H₂ that is recycled back to the hydrogasifier, the net hydrogen production is 222 kg/h with an amount of CO₂ released of 2265 kg/h. For the different process configurations adopted, the energy efficiency of the process ranges 84–89%.     

Concept design of a novel reformer producing hydrogen for internal combustion engines using fuel decomposition method: Performance evaluation of coated monolith suitable for on-board applications

Hydrogen addition effectively reduces the fuel consumption of spark ignition engines. We propose a new on-board reformer that produces hydrogen at high concentrations and enables multi-mode operations. For the proposed reformer, we employ a catalytic fuel decomposition reaction via a commercial NiO–CaAl₂O₄ catalyst. We explore the physical and chemical aspects of the reforming process using a fixed bed micro-reactor operating at temperatures of 550–700 °C. During reduction, methane is decomposed to form hydrogen and carbon. Carbon formation is critical to hydrogen production, and free space for carbon growth is essential at low temperatures (≤600 °C). We define a new accumulated conversion ratio that quantitatively measures highly transient catalytic decomposition. The free space of the coated monolith clearly aided low-temperature decomposition with negligible pressure drop. The coated substrate is therefore suitable for on-board applications considering that our reformer concept also utilizes the catalytic fuel decomposition reaction.     

Steam reforming of hot gas from gasified wood types and miscanthus biomass

The reforming of hot gas generated from biomass gasification and high temperature gas filtration was studied in order to reach the goal of the CHRISGAS project: a 60% of synthesis gas (as x(H₂)+ x(CO) on a N₂ and dry basis) in the exit gas, which can be converted either into H₂ or fuels. A Ni-MgAl₂O₄ commercial-like catalyst was tested downstream the gasification of clean wood made of saw dust, waste wood and miscanthus as herbaceous biomass. The effect of the temperature and contact time on the hydrocarbon conversion as well as the characterization of the used catalysts was studied. Low (<600 °C), medium (750°C–900 °C) and high temperature (900°C–1050 °C) tests were carried out in order to study, respectively, the tar cracking, the lowest operating reformer temperature for clean biomass, the methane conversion achievable as function of the temperature and the catalyst deactivation. The results demonstrate the possibility to produce an enriched syngas by the upgrading of the gasification stream of woody biomass with low sulphur content. However, for miscanthusthe development of catalysts with an enhanced resistance to sulphur poison will be the key point in the process development.     

Simulation and optimization of hydrogen production by steam reforming of natural gas for refining and petrochemical demands in Lebanon

Steam reforming of natural gas produces the majority of the world's hydrogen (H₂) and it is considered as a cost-effective method from a product yield and energy consumption point of view. In this work, we present a simulation and an optimization study of an industrial natural gas steam reforming process by using Aspen HYSYS and MATLAB software. All the parameters were optimized to successfully run a complete process including the hydrogen production zone units (reformer reactor, high temperature gas shift reactor HTS and low temperature gas shift reactor LTS) and the purification zone units (absorber and methanator). Optimum production of hydrogen (87,404 MT/year) was obtained by fixing the temperatures in the reformer and the gas shift reactors (HTS & LTS) at 900 °C, 500 °C and 200 °C respectively while maintaining a pressure of 7 atm, and a steam to carbon ratio (S/C) of 4. Moreover, ~99% of the undesired CO₂ and CO gases were removed in the purification zone and a reduction of energy consumption of 77.5% was reached in the heating and cooling units of the process.     

Hydrogen production enhancement using hot gas cleaning system combined with prepared Ni-based catalyst in biomass gasification

This paper investigates the hot gas temperature effect on enhancing hydrogen generation and minimizing tar yield using zeolite and prepared Ni-based catalysts in rice straw gasification. Results obtained from this work have shown that increasing hot gas temperature and applying catalysts can enhance energy yield efficiency. When zeolite catalyst and hot gas temperature were adjusted from 250 °C to 400 °C, H₂ and CO increased slightly from 7.31% to 14.57%–8.03% and 17.34%, respectively. The tar removal efficiency varies in the 70%–90% range. When the zeolite was replaced with prepared Ni-based catalysts and hot gas cleaning (HGC) operated at 250 °C, H₂ contents were significantly increased from 6.63% to 12.24% resulting in decreasing the hydrocarbon (tar), and methane content. This implied that NiO could promote the water-gas shift reaction and CH₄ reforming reaction. Under other conditions in which the hot gas temperature was 400 °C, deactivated effects on prepared Ni-based catalyst were observed for inhibiting syngas and tar reduction in the HGC system. The prepared Ni-based catalyst worked at 250 °C demonstrate higher stability, catalyst activity, and less coke decomposition in dry reforming. In summary, the optimum catalytic performance in syngas production and tar elimination was achieved when the catalytic temperature was 250 °C in the presence of prepared Ni-based catalysts, producing 5.92 MJ/kg of lower heating value (LHV) and 73.9% tar removal efficiency.     

Numerical and experimental study on hydrogen production via dimethyl ether steam reforming

This work presents the characteristics of catalytic dimethyl ether (DME)/steam reforming based on a Cu–Zn/γ-Al₂O₃ catalyst for hydrogen production. A kinetic model for a reformer that operates at low temperature (200 °C–500 °C) is simulated using COMSOL 5.2 software. Experimental verification is performed to examine the critical parameters for the reforming process. During the experiment, superior Cu–Zn/γ-Al₂O₃catalysts are manufactured using the sol-gel method, and ceramic honeycombs coated with this catalyst (1.77 g on each honeycomb, five honeycombs in the reactor) are utilized as catalyst bed in the reformer to enhance performance. The steam, DME mass ratio is stabilized at 3:1 using a mass flow controller (MFC) and a generator. The hydrogen production rate can be significantly affected depending on the reactant's mass flow rate and temperature. And the maximum hydrogen yield can reach 90% at 400 °C. Maximum 8% error for the hydrogen yield is achieved between modeling and experimental results. These experiments can be further explored for directly feeding hydrogen to proton exchange membrane fuel cell (PEMFC) under the load variations.     

Hydrogen-rich syngas production and carbon dioxide formation using aqueous urea solution in biogas steam reforming by thermodynamic analysis

Biogas is a renewable biofuel that contains a lot of CH₄ and CO₂. Biogas can be used to produce heat and electric power while reducing CH₄, one of greenhouse gas emissions. As a result, it has been getting increasing academic attention. There are some application ways of biogas; biogas can produce hydrogen to feed a fuel cell by reforming process. Urea is also a hydrogen carrier and could produce hydrogen by steam reforming. This study then employes steam reforming of biogas and compares hydrogen-rich syngas production and carbon dioxide with various methane concentrations using steam and aqueous urea solution (AUS) by Thermodynamic analysis. The results show that the utilization of AUS as a replacement for steam enriches the production of H₂ and CO and has a slight CO₂ rise compared with pure biogas steam reforming at a temperature higher than 800 °C. However, CO₂ formation is less than the initial CO₂ in biogas. At the reaction temperature of 700 °C, carbon formation does not occur in the reforming process for steam/biogas ratios higher than 2. These conditions led to the highest H₂, CO production, and reforming efficiency (about 125%). The results can be used as operation data for systems that combine biogas reforming and applied to solid oxide fuel cell (SOFC), which usually operates between 700 °C to 900 °C to generate electric power in the future.     

Thermodynamic study on the integrated supercritical water gasification with reforming process for hydrogen production: Effects of operating parameters

In this paper, a conceptual process design of the integrated supercritical water gasification (SCWG) and reforming process for enhancing H₂ production has been developed. The influence of several operating parameters including SCWG temperature, SCWG pressure, reforming temperature, reforming pressure and feed concentration on the syngas composition and process efficiency was investigated. In addition, the thermodynamic equilibrium calculations have been carried out based on Gibbs free energy minimization by using Aspen Plus. The results showed that the higher H₂ production could be obtained at higher SCWG temperature, the H₂ concentration increased from 5.40% at 400 °C to 38.95% at 600 °C. The lower feed concentration was found to be favorable for achieving hydrogen-rich gas. However, pressure of SCWG had insignificant effect on the syngas composition. The addition of reformer to the SCWG system enhanced H₂ yield by converting high methane content in the syngas into H₂. The modified SCWG enhanced the productivity of syngas to 151.12 kg/100kg_feed compared to 120.61 kg/100kg_feed of the conventional SCWG system. Furthermore, H₂ yield and system efficiency increased significantly from 1.81 kg/100kg_feed and 9.18% to 8.91 kg/100kg_feed, and 45.09%, respectively, after the modification.     

Syngas and hydrogen production via stepwise methane reforming over Cu‐ferrite/YSZ

This report investigates the effect of an yttria‐stabilized zirconia (YSZ) supported Cu‐ferrite for the production of syngas and hydrogen via stepwise methane reforming and water splitting reactions. The Cu‐ferrite/YSZ samples were prepared by co‐precipitation and impregnation methods. The samples were characterized by X‐ray diffraction spectroscopy and non‐isothermal hydrogen reduction. To investigate syngas and hydrogen production reactivities, isothermal methane reforming and water splitting reactions were performed at 900 °C and 700 °C, respectively. For Cu‐ferrite/YSZ prepared by impregnation, methane conversion was maintained at high levels of ca. 85% and an H₂/CO ratio close to 2 was observed. A lower methane conversion (>30%) was observed for Cu‐ferrite/YSZ prepared by co‐precipitation. No significant deposited carbon and aggregation of Cu‐ferrite/YSZ (prepared by impregnation) were observed over 10 repeated methane reforming and water splitting reactions. Copyright © 2014 John Wiley & Sons, Ltd.     

Dry reforming of methane powered by magnetic induction

Dry reforming of methane is a highly endothermic reaction that produces syngas from CH₄ and CO₂. It operates at 800–1000 °C to meet thermodynamic constraints, achieve high equilibrium conversion and minimize catalyst deactivation due to carbon deposition. In this paper we report our experimental results on the catalytic activation of dry reforming powered by induction heating. Energy is supplied by a radiofrequency alternating magnetic field to Ni₆₀Co₄₀ alloy that works at the same time as catalyst for the reforming reaction and heat generator by dissipation of the electromagnetic energy. In such a way, the heat of reaction is directly provided by the catalytic bed, avoiding dissipation due to inefficient transfer from outside the reactor.Temperatures higher than 850 °C have been easily reached using Ni₆₀Co₄₀ pellets as heat mediators in a continuous-flow fixed-bed reactor. At this temperature methane conversion and hydrogen production occurred with yield comparable to those obtained by conventional heating. Reported evidences open new opportunities in the research of magnetic materials for industrial chemical processes.     

Glycerol steam reforming in a bench scale continuous flow heat recovery reactor

In the present study glycerol was successfully gasified using a diesel engine waste heat recovery system obtaining hydrogen and methane rich gaseous products. The reforming reactor was equipped with a vaporization pre-chamber to ensure uniform reactants distribution and a fixed reaction bed, being mounted in countercurrent flow configuration with the engine combustion gases stream. Accordingly, the reactions were conducted at gradually increased temperature conditions; starting at around 300 °C in the top section of the reaction bed and finishing in a controlled outlet bed temperature of 600–800 °C. When compared to homogeneous temperature reactors, the configuration used here produced a syngas of higher methane and ethylene contents. With regards to the reactor performance, syngas lower heat values of more than 22 MJ/kg were achieved with glycerol feed concentrations within 50–70% and outlet bed temperatures above 700 °C, corresponding to cold gas efficiencies of around 85%. The present results indicate that glycerin can be utilized as a syngas feedstock for steam reforming processes based on waste heat recovery.     

Hydrogen production via steam reforming of coke oven gas enhanced by steel slag-derived CaO

Steel slag, a waste from steelmaking plant, has been proven to be good candidate resources for low-cost calcium-based CO₂ sorbent derivation. In this work, a cheap and sintering-resistance CaO-based sorbent (CaO (SS)) was prepared from low cost waste steel slag and was applied to enhance catalytic steam reforming of coke oven gas for production of high-purity hydrogen. This steel slag-derived CaO possessed a high and stable CO₂ capture capacity of about 0.48 g CO₂/g sorbent after 35 adsorption/desorption cycles, which was mainly ascribed to the mesoporous structure and the presence of MgO and Fe₂O₃. Product gas containing 95.8 vol% H₂ and 1.4 vol% CO, with a CH₄ conversion of 91.3% was achieved at 600 °C by steam reforming of COG enhanced by CaO (SS). Although high temperature was beneficial for methane conversion, CH₄ conversion was remarkably increased at lower operation temperatures with the promotion effects from CaO (SS), and CO selectivity has been also greatly decreased. Reducing WHSV could increase methane conversion and reduce CO selectivity due to longer reactants residence time. Reducing C/A could increase methane conversion and hydrogen recovery factor, and also decrease CO selectivity. When being mixed with catalyst during SE-SRCOG, CaO (SS) with a uniform size distribution favored methane conversion due to the high utilization efficiency of catalyst. Promising stability of CaO (SS) in cyclic reforming/calcination tests was evidenced with a hydrogen recovery factor >2.1 and CH₄ conversion of 82.5% at 600 °C after 10 cycles using CaO (SS) as sorbent.     

Combustion characteristics of anode off-gas on the steam reforming performance

The combination of steam reforming and HT-PEMFC has been considered as a proper set up for the efficient hydrogen production. Recycling anode off-gas is energy-saving strategy, which leads to enhance the overall efficiency of the HT-PEMFC. Thus, the recycling effect of anode off-gas on steam-reforming performance needs to be further studied. This paper, therefore, investigated that the combustion of anode off-gas recycled impacts on the steam reformer, which consists of premixed-flame burner, steam reforming and water-gas shift reactors. The temperature rising of internal catalyst was affected by lower heating value of fuels when the distance between catalyst and burner is relatively short, while by the flow rate of fuels and the steam to carbon ratio when its distance is long. The concentration of carbon monoxide was the lowest at 180 °C of LTS temperature, while NG and AOG modes showed the highest thermal efficiency at LTS temperature of 220–300 °C and 270–350 °C, respectively. The optimum condition of thermal efficiency to maximize hydrogen production was determined by steam reforming rather than water gas shift reaction. It was confirmed that the condition to obtain the highest thermal efficiency is about 650 °C of steam reforming temperature, regardless of combustion fuel and carbon monoxide reduction. The difference of hydrogen yield between upper and lower values is up to 1.5 kW as electric energy with a variation of thermal efficiency. Hydrogen yield showed the linear proportion to the thermal efficiency of steam reformer, which needs to be further increased through proper thermal management.