Studies on influence of hydrogen and carbon monoxide concentration on reduction progression behavior of molybdenum oxide catalyst

Temperature programmed reduction (TPR) analysis was applied to investigate the chemical reduction progression behavior of molybdenum oxide (MoO₃) catalyst. The composition and morphology of the reduced phases were characterized by X-ray diffraction spectroscopy (XRD), X-ray photoelectron spectroscopy (XPS), and field emission scanning electron microscopy (FE-SEM). The reduction progression of MoO₃ catalyst was attained with different reductant types and concentration (10% H₂/N₂, 10% and 20% CO/N₂ (%, v/v)). Two different modes of reduction process were applied. The first approach of reduction involved non-isothermal mode reduction up to 700 °C, while the second approach of reduction involved the isothermal mode reduction for 60 min at 700 °C. Hydrogen temperature programmed reduction (H₂-TPR) results showed the reduction progression of three-stage reduction of MoO₃ (Mo⁶⁺ → Mo⁵⁺ → Mo⁴⁺ → Mo⁰) with Mo⁵⁺ and Mo⁴⁺. XRD analysis confirmed the formation of Mo₄O₁₁ phase as an intermediate phase followed by MoO₂ phase. After 60 min of isothermal reduction, peaks of metallic molybdenum (Mo) appeared. Whereas, FESEM analysis showed porous crater-like structure on the surface cracks of MoO₂ layer which led to the growth of Mo phase. Meanwhile, the reduction of MoO₃ catalyst in 10% carbon monoxide (CO) showed the formation of unstable intermediate phase of Mo₉O₂₆ at the early stage of reduction. Furthermore, by increasing 20% CO led to the carburization of MoO₂ phase, resulted in the formation of Mo₂C rather than the formation of metallic Mo, as confirmed by XPS analysis. Therefore, the presented study shows that hydrogen gave better reducibility due to smaller molecular size, which contributed to high diffusion rate and achieved deeper penetration into the MoO₃ catalyst compared to carbon monoxide reductant. Hence, the reduction of MoO₃ in carbon monoxide atmosphere promoted the formation of Mo₂C which was in agreement with the thermodynamic assessment.     

Boosting electrochemical hydrogen evolution activity of MoS2 nanosheets via facile decoration of Au overlayer

--Owing to its unique physicochemical properties, two-dimensional (2D) layered MoS₂ has been proposed as a potential catalyst for efficient hydrogen evolution reaction (HER). However, their large-scale application is still hindered due to limited active sites, poor conductivity, and restacking during synthesis. Herein, we report a one-step hydrothermal route to grow MoS₂ nanosheets on molybdenum (Mo) foil substrate followed by Au decoration as an active cocatalyst to enhance the HER performance of MoS₂ nanosheets. A facile, quick, and controlled decoration of stable Au overlayer with different mass loadings was performed using a sputtering Au coating unit for different deposition times (10s, 30s, and 50s), thus paving the way for producing efficient and inexpensive HER electrocatalysts. Electrochemical studies of different Au–MoS₂/Mo hybrids demonstrate that the optimized Au–MoS₂/Mo-30s sample exhibits ultralow onset potential (52 ± 2 mV vs. RHE), small overpotentials of 136 ± 6 and 318 ± 3 mV (vs. RHE) at current densities of 10 and 100 mA cm^?2, a small Tafel slope (46.23 ± 6 mV/dec), along with an outstanding electrochemical stability over a couple of days. Presence of metallic 1T-phase of MoS₂, as well as the synergistic effect between MoS₂ and Au, result in enhanced electrical conductivity, high density of active sites, large electrochemically accessible surface area, and fast charge transfer at the catalyst-electrolyte interface for boosting HER activity of the hybrid catalyst.     

Rational design of Ni-induced NC @Mo2C@MoS2 sphere electrocatalyst for efficient hydrogen evolution reaction in acidic and alkaline media

Exploiting efficient and low-cost electrocatalyst for Hydrogen Evolution Reaction (HER) of water electrolysis remains a challenge. Herein, we designed an efficient electrocatalyst of Ni-induced nitrogen-doped carbon @ molybdenum carbide @ molybdenum disulfide sphere (NC@Mo₂C@MoS₂-(Ni)) by two simple coating steps following pyrolysis process. Benefiting from the regular spherical morphology, unique structure, synergistic effect between Mo₂C and MoS₂, inducement effect of elemental Ni that initial added and removed in final synthesis procedure, heteroatom N and P doping. The catalyst NC@Mo₂C@MoS₂-(Ni) exhibits relatively good catalytic performance of overpotentials of 205 and 216 mV at 10 mA cm^?2 and Tafel slopes of 61.4 and 42.7 mV dec^?1 in acidic and basic media, respectively. This work not only fabricate the electrocatalyst of NC@Mo₂C@MoS₂-(Ni) towards HER, but also provides a way to rationally design more efficient other functional electrocatalysts.     

Vapor-assisted engineering heterostructure of 1D Mo3N2 nanorod decorated with nitrogen-doped carbon for rapid pH-Universal hydrogen evolution reaction

Reasonable construction of heterostructure is of significance yet a great challenge towards efficient pH-universal catalysts for hydrogen evolution reaction (HER). Herein, a facial strategy coupling gas-phase nitridation with simultaneous heterogenization has been developed to synthesize heterostructure of one-dimensional (1D) Mo₃N₂ nanorod decorated with ultrathin nitrogen-doped carbon layer (Mo₃N₂@NC NR). Thereinto, the collaborative interface of Mo₃N₂ and NC is conducive to accomplish rapid electron transfer for reaction kinetics and weaken the Mo–H_ads bond for boosting the intrinsic activity of catalysts. As expected, Mo₃N₂@NC NR delivers an excellent catalytic activity for HER with low overpotentials of 85, 129, and 162 mV to achieve a current density of 10 mA cm^?2 in alkaline, acidic, and neutral electrolytes, respectively, and favorable long-term stability over a broad pH range. As for practical application in electrocatalytic water splitting (EWS) under alkaline, Mo₃N₂@NC NR || NiFe-LDH-based EWS also exhibits a low cell voltage of 1.55 V and favorable durability at a current density of 10 mA cm^?2, even surpassing the Pt/C || RuO₂-based EWS (1.60 V). Consequently, the proposed suitable methodology here may accelerate the development of Mo-based electrocatalysts in pH-universal non-noble metal materials for energy conversion.     

Efficient overall water splitting over a Mo(IV)-doped Co3O4/NC electrocatalyst

To meet the demand of producing hydrogen at low cost, a molybdenum (Mo)-doped cobalt oxide (Co₃O₄) supported on nitrogen (N)-doped carbon (x%Mo–Co₃O₄/NC, where x% represents Mo/Co molar ratio) is developed as an efficient bifunctional electrocatalyst for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). This defect engineering strategy is realized by a facile urea oxidation method in nitrogen atmosphere. Through X-ray diffraction (XRD) refinement and other detailed characterizations, molybdenum ion (Mo⁴⁺) is found to be doped into Co₃O₄ by substituting cobalt ion (Co²⁺) at tetrahedron site, while N is doped into carbon matrix simultaneously. 4%Mo–Co₃O₄/NC is the optimized sample to show the lowest overpotentials of 91 and 276 mV to deliver 10 mA cm^?2 for HER and OER in 1 M potassium hydroxide solution (KOH), respectively. The overall water splitting cell 4%Mo–Co₃O₄/NC||4%Mo–Co₃O₄/NC displays a voltage of 1.62 V to deliver 10 mA cm^?2 in 1 M KOH. The Mo⁴⁺ dopant modulates the electronic structure of active cobalt ion (Co³⁺) and boosts the water dissociation process during HER, while the increased amount of lattice oxygen and formation of pyridinic nitrogen due to Mo doping benefits the OER activity. Besides, the smaller grain size owing to Mo doping leads to higher electrochemically active surface area (ECSA) on 4%Mo–Co₃O₄/NC, resulting in its superior bifunctional catalytic activity.     

Effect of Mo content on hydrogen evolution reaction activity of Mo2C/C electrocatalysts

Recent research suggests that molybdenum carbide (β-Mo₂C) has the potential to be a cheap and active substitute for Pt-based electrocatalyst for hydrogen evolution reaction. In this article molybdenum carbide (Mo₂C) electrocatalysts immobilized on carbon support were synthesized and evaluated for hydrogen evolution reaction (HER). The quantity of Mo in the samples was varied to understand the effect of Mo content in Mo₂C/C electrocatalyst on the structure, morphology, electrochemical properties and HER. The Mo weight percentages determined by ICP-OES technique in four Mo₂C/C samples prepared were found as ~9.3, 15.8, 20.4 and 28.0. SAXS studies revealed that the pore size of the carbon increased with an increase in Mo content, most probably to accommodate the Mo₂C motifs. X-ray photoelectron spectra showed that the amount of low valent Mo increased as we increased the Mo content up to 20 wt % but decreased in the 28 wt % sample. All the samples were active for electrochemical HER with the sample having ~20 wt % Mo showing the highest activity and exhibited a Tafel slope of 69 mVdec⁻¹. Among all samples the 20 wt% Mo sample exhibited the highest electrochemical surface area (ECSA) of ~2.92 mFcm⁻² and minimum charge transfer resistance for the HER. Thus, it is concluded that 20 wt% Mo in Mo₂C/C electrocatalyst evolves with ideal pore size, highest ECSA, smooth charge transfer and thus exhibits the best electrochemical properties for HER.     

Transition metal doped MoS2 nanosheets for electrocatalytic hydrogen evolution reaction

In the present work, the effect of transition metals (Ni, Fe, Co) doping on 2-dimensional (2D) molybdenum disulfide (MoS₂) nanosheets for electrocatalytic hydrogen evolution reaction (HER) was explored. A simple and cost-effective hydrothermal method was adopted to synthesis transition metals doped MoS₂ nanosheets. The morphological and spectroscopic studies evidence the formation of high-quality MoS₂ nanosheets with the randomly doped metal ions. Notably, the Ni–MoS₂ displayed superior HER performance with an overpotential of ?0.302 V vs. reversible hydrogen electrode (RHE) (to attain the current density of 10 mA cm^?2) as compared to the other transition metals doped MoS₂ (Co–MoS₂, Fe–MoS₂). From the Nyquist plot, superior charge transport from the electrocatalyst to the electrolyte in Ni–MoS₂ was realized and confirmed that Ni doping provides the necessary catalytic active sites for rapid hydrogen production. The stable performance was confirmed with the cyclic test and chronoamperometry measurement and envisaged that hydrothermally synthesized Ni–MoS₂ is a highly desirable cost-effective approach for electrocatalytic hydrogen generation.     

Polyoxomolybdate-derived MoS2/nitrogen-doped reduced graphene oxide hybrids for efficient hydrogen evolution

Integrating MoS₂ with carbon-based materials, especially graphene, is an effective strategy for preparing highly active non-noble-metal electrocatalysts in the hydrogen evolution reaction (HER). This work demonstrates a convenient hydrothermal method to fabricate molybdenum disulfide nanosheets/nitrogen-doped reduced graphene oxide (MoS₂/NGO) hybrids using polyoxomolybdate as the Mo precursor. Introducing more defects and expanding interlayer spacing of MoS₂ can be achieved through decreasing the pH value of the reactive system due to the existed high-nuclear polyoxometalate clusters. MoS₂/NGO hybrids prepared at low pH exhibit superior HER activity to those obtained at high pH. MoS₂/NGO-pH1.5 exhibits an ultralow overpotential of 81 mV at 10 mA cm⁻², a low Tafel slope of 60 mV·dec⁻¹ and good stability in alkaline electrolyte. Such excellent electrocatalytic activity is contributed by the abundant HER catalytic active sites, the increased electrochemically-accessible area and the synergetic effects between the active MoS₂ catalyst and NGO support.     

Carbon-coated molybdenum carbide nanosheets derived from molybdenum disulfide for hydrogen evolution reaction

The design and synthesis of efficient non-noble metal catalyst is important for the practical application of hydrogen evolution reaction (HER) from water electrolysis. In this study, molybdenum carbides were prepared by a novel synthetic method, which involved the first exfoliation of 2D MoS₂ based on the principle of cold expansion of water below 4 °C and then carburization of exfoliated MoS₂. In this method, MoS₂ played roles of morphology template and molybdenum source simultaneously. Carbon-coated molybdenum carbide nanosheets were obtained and confirmed by X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and transmission electron microscopy. The stripping degree of MoS₂ was found to have an important influence on physical properties and catalytic performance of molybdenum carbides. Interestingly, Mo₂C nanosheets encapsulated in carbon nanotubes were observed when the MoS₂ with a high peeling degree was used in the preparation. It showed high activity and good durability towards HER in acid solution.     

Zeolite imidazolate framework-8 derived molybdenum carbide/nitrogen-doped carbon for highly-efficient hydrogen evolution reaction

A metal-organic framework-derived method was developed to synthesize highly efficient non-noble metal electrocatalyst for alkaline hydrogen evolution reaction (HER). Zn²⁺, phosphomolybdic acid were coordinated with 2-methylimidazole, and zinc (Zn) and phosphorus (P) species were removed by annealing at 850 °C in N₂ atmosphere, resulting in micro/mesoporous molybdenum carbide (Mo₂C) composited with nitrogen-doped carbon (denoted as ZIF8-xMo-850). The optimized sample ZIF8-12Mo-850 displayed a low overpotential of ~85.7 mV to deliver a current density of 10 mA cm⁻², with a corresponding Tafel slope of ~69.7 mV dec⁻¹ in 1 M KOH. This HER catalytic activity was competitive with the most recently developed Mo₂C-based HER electrocatalysts. From further investigation, the high HER catalytic activity of ZIF8-12Mo-850 is owing to three aspects: (i) The appropriate Mo feeding amount of ZIF8-12Mo-850 resulted in the highest surface content of Mo²⁺ active site; (ii) The evaporation of Zn and P in the ZIF8-12Mo precursor formed its largest average pore diameter of 32.3 nm, which leaded to the highest electrochemically active surface area (ECSA) of 64.29 cm² (iii) The 2-methylimidazole in the precursor resulted in the highest surface content of pyridinic N in ZIF8-12Mo-850 (14.63%), which efficiently improved its conductivity and charge transfer efficiency.     

Interfacing perovskite strontium molybdate to molybdenum disulfide nanoplatelts for boosting HER from water

Due to low hydrogen adsorption free energy at the edges of 2D-MoS₂ layered sheets, nanostructured MoS₂ materials recently are assigned to prospective electrocatalysts for hydrogen evolution reaction (HER) from water. However, the efficiency and stability of HER onto the MoS₂ designed on the conductive substrates are poor. To significantly increase the number of active sites and achieve a long-time working stability, the design of hybrid-type electrodes is crucial. Here, we report the synthesis of a new hybrid material composed of molybdenum disulfide and molybdenum oxides heterostructured with strontium molybdate. For this, a facile one-pot hydrothermal process was developed directly onto the TiO₂ nanotube carpet substrate. The interfacing of strontium molybdate at the electrode substrate verified by X-ray photoelectron spectroscopy and Time of flight secondary ions mass spectrometry (ToF SIMS) techniques. Considerable higher catalytic activity at the surface of this hybrid film, with the onset potential of 190 mV vs RHE and a Tafel slope of 66 mV dec^?1 attaining ~80 mA cm^?2 at 0.35 V overvoltage was ascertained. Exciting HER stability in comparison with the pure synthetic MoS₂ was verified by a prolonged potential cycling from 0.05 to ?0.35 V versus RHE potential and 45 h continuous HER processing at a constant current density.     

Preparation of ultrathin molybdenum disulfide dispersed on graphene via cobalt doping: A bifunctional catalyst for hydrogen and oxygen evolution reaction

The development of highly active and low-cost catalysts for hydrogen evolution reaction (HER) is significant for the development of clean and renewable energy research. Owing to the low H adsorption free energy, molybdenum disulfide (MoS₂) is regarded as a promising candidate for HER, but it shows low activity for oxygen evolution reaction (OER). Herein, graphene-supported cobalt-doped ultrathin molybdenum disulfide (Co–MoS₂/rGO) was synthesized via a one-pot hydrothermal method. The obtained hybrids modified electrode exhibits a high HER catalytic activity with a low overpotential of 147 mV at the current density of 10 mA cm⁻², a small Tafel slope of 49.5 mV dec⁻¹, as well as good electrochemical stability in acidic electrolyte. Meanwhile, the catalyst shows remarkable OER activity with a low overpotential of 347 mV at 10 mA cm⁻². The superior activity is ascribed not only to the high conductivity originated from the reduced graphene, but also to the synergistic effect between MoS₂ and cobalt.     

Efficient and long-term photocatalytic H2 evolution stability enabled by Cs2AgBiBr6/MoS2 in aqueous HBr solution

Lead-free Cs₂AgBiBr₆ (CABB) double perovskite as a new-type photocatalytic material alternative to lead halide perovskites holds promise to implement the solar-H₂ conversion, but the interior recombination of photo-generated carriers and thus low photocatalytic hydrogen evolution reaction (HER) rate of CABB restrict its further industrial applications. Herein, we report the composite fabrication of MoS₂/CABB heterostructure for high-efficiency and durable photocatalytic HER by anchoring non-noble MoS₂ onto CABB via a facile dissolution-recrystallization method. The optimized MoS₂/CABB performs a visible-light HER rate of 87.5 μmol h^?1 g^?1 in aqueous HBr solution, ca. 20-fold compared to that of pure CABB (4.3 μmol h^?1 g^?1), and presents a discontinuous 500-h photocatalytic HER stability with no evident loss. The superb performance of MoS₂/CABB can be ascribed to the kinetics-facilitated heterostructure consisting of stable CABB and MoS₂. This work proposes a facile and versatile tactic to construct a low-cost Cs₂AgBiBr₆-based heterostructure for efficient and long-term photocatalytic HER.     

High throughput preparation of Ni–Mo alloy thin films as efficient bifunctional electrocatalysts for water splitting

The synthesis of cost-effective and high-performance electrocatalysts for water splitting is the main challenge in electrochemical hydrogen production. In this study, we adopted a high throughput method to prepare bi-metallic catalysts for oxygen/hydrogen evolution reactions (OER/HER). A series of Ni–Mo alloy electrocatalysts with tunable compositions were prepared by a simple co-sputtering method. Due to the synergistic effect between Ni and Mo, the intrinsic electrocatalytic activity of the Ni–Mo alloy electrocatalysts is improved, resulting in excellent HER and OER performances. The Ni₉₀Mo₁₀ electrocatalyst shows the best HER performance, with an extremely low overpotential of 58 mV at 10 mA cm^?2, while the Ni₄₀Mo₆₀ electrocatalyst shows an overpotential of 258 mV at 10 mA cm^?2 in OER. More significantly, the assembled Ni₄₀Mo₆₀//Ni₉₀Mo₁₀ electrolyzer only needs a cell voltage of 1.57 V to reach 10 mA cm^?2 for overall water splitting.     

New insights into high-valence state Mo in molybdenum carbide nanobelts for hydrogen evolution reaction

Hydrogen evolution reaction (HER) is considered to be one of the most promising strategies to create hydrogen. Recently, searching high-efficient, stable, and earth-abundant electrocatalysts to replace precious metals for practical utilizations of HER is attracting more and more attentions. Herein, novel molybdenum carbide nanobelts containing Mo of high-valence state derived from MoO₃-ethylenediamine inorganic/organic hybrid precursors are successfully synthesized via a facile one-pot pyrolysis method. The molybdenum carbide nanobelts are characterized using XRD, SEM, TEM and XPS. Moreover, the high-valence state Mo and their relative content in the molybdenum carbide nanobelts can be identified by XPS. The high-resolution XPS spectra of Mo 3d indicates in the molybdenum carbide nanobelts the proportion of high-valence state Mo in active Mo components is 51.3%. More importantly, the as-synthesized products exhibit excellent electrocatalytic activity for HER with a low onset overpotential of 50 mV and a small Tafel slope of 49.6 mV dec^?1 in acidic medium (0.5 M H₂SO₄). Besides, the catalysts require only overpotentials of 143 and 234 mV to achieve current densities of 10 and 220 mA cm^?2, respectively. Furthermore, they also exhibit good durability after 2000 cycles and constant current density test. Such excellent electrocatalytic HER performance can be ascribed to the high intrinsic activity of high-valence state Mo in Molybdenum Carbide. Synthesizing molybdenum carbide with high-valence state Mo electrocatalysts for HER will open up an exciting alternative avenue to acquire outstanding HER electrocatalytic activity.     

Growth of porous single-crystalline molybdenum nitrides microcubes with enhanced electrocatalysis performance

Porous single crystal has the characteristics of long-range order, continuous lattice and large specific surface area, which could reduce energy losses and keep high activity and stability in electrochemical systems. Here, we grow porous single-crystalline and polycrystalline molybdenum nitrides microcubes from MoO₃ single crystals. These porous microcubes show superior HER and OER performance. The overpotential of Mo₂N porous single crystal microcubes is only 73.13 mV at a current density of 10 mA cm^?2, which is 150.53 mV, 192.76 mV and 255.87 mV lower than that of MoN single crystal, Mo₂N polycrystal and MoN polycrystal, respectively. The advantages of Mo₂N porous single crystals in electrocatalytic properties are also reflected in OER.     

Phosphorus-doping induced electronic modulation of CoS2–MoS2 hollow spheres on MoO2 film-Mo foil for synergistically boosting alkaline hydrogen evolution reaction

Combination of anionic doping and multicomponent synergism are effective approach to improve the performance of electrocatalysts toward hydrogen evolution reaction (HER) process. Herein, P-doped CoS₂–MoS₂ hollow spheres assembled by countless sheets on oxidized Mo foil (P–CoS₂/MoS₂/MoO₂) was synthesized by hydrothermal and phosphorization process. The unique hollow structure with countless sheets as wall endows more accessible active sites, fast electron/mass transport and high conductivity. P-doping could redistribute the local charge density and optimize the surface charge state to improve the intrinsic activity and accelerate reaction kinetics. The optimized P–CoS₂/MoS₂/MoO₂ exhibits an outstanding HER performance with an overpotential of 85 mV to reach 10 mA cm⁻², a small Tafel slope of 84.6 mV dec⁻¹, superior intrinsic HER activity and robust durability under alkaline solution. This work proposed a feasible strategy to build the hollow, heterostructured and binder-free electrode in renewable energy application.     

Facile preparation of N,P co-doped molybdenum carbide / porous carbon rough microspheres for efficient electrocatalytic hydrogen evolution

Despite that diverse carbon materials have been designed as framework to anchor molybdenum carbide to efficiently improve catalytic performance for hydrogen evolution reaction (HER), simply and uniformly hybridizing Mo and carbon source to form well-defined heteroatom-doped Mo₂C/carbon nanostructure using suitable precursors to expose the more active sites and optimize electron structure Mo₂C is still great challenge. Herein, we design and fabricate N, P-co-doped molybdenum carbide/porous carbon hybrid rough microspheres by a simple hydrothermal and followed annealing method using red jujube and phosphomolybdic acid as carbon and Mo source, respectively. Benefiting from carbon framework derived from red jujube inhibiting the aggregation of Mo₂C nanoparticles, N, P co-doping changing the electro-structure of the adjacent Mo and C atoms, and rough micro-spherical structure increasing the electrolyte-active materials contact surface, the resulting material exhibits high electrocatalytic performance with a low overpotential of 103 and 80 mV at current densities of 10 mA cm⁻², a small Tafel slope of 57 and 46 mV dec⁻¹, respectively, in acidic and alkaline electrolyte, and excellent stability. The convenient resource, facile preparation and high performance make this material showing great potential in cost effective hydrogen production.     

In-situ “encapsulation” of Mo:Mo2C with nano-mosaic structure on wood-derived carbon for hydrogen evolution reaction

Coupling metallic and Mo₂C phases uniformly on conductive matrix at nanoscale is a promising route to solve the poor electrical conductivity and aggregation problems of nano-Mo₂C. In this work, a 3D self-supporting carbonized wood (CW) electrode encapsulation with mosaic structure Mo:Mo₂C for hydrogen evolution reaction was fabricated successfully by a facile annealing treatment and a gas-solid reaction. The presence of Mo phase accelerated the transfer rate of electrons and provided heterogeneous interface. The obtained electrode shows abundant catalytic active sites and low electrochemical impedance, thus improving the catalytic process of splitting water for HER. The Mo:Mo₂C-775 electrode requires an overpotential of 73.5 mV and 117 mV to achieve the current density of 10 mA cm^?2 in 0.5 M H₂SO₄ and 1.0 M KOH, respectively. Moreover, Mo:Mo₂C-775 electrode displayed excellent stability performance, which almost maintained a constant current density for 12 h (at ?100 mV vs RHE) in 0.5 M H₂SO₄ and 1.0 M KOH, respectively. This study provides a new idea for preparation of efficient 3D self-supporting electro-catalyst for HER.     

MoS2–Co3S4 hollow polyhedrons derived from ZIF-67 towards hydrogen evolution reaction and hydrodesulfurization

Co–Mo–S based catalysts have promising applications in both hydrogen evolution reaction (HER) and hydrodesulfurization (HDS). Herein, MoS₂–Co₃S₄ hollow polyhedrons have been successfully synthesized by the vulcanization of Mo doped ZIF-67. MoS₂–Co₃S₄ hollow polyhedrons show the superior HER and HDS catalytic activities to pure MoS₂, Co₃S₄ and MoS₂–Co₃S₄ nanoparticles prepared by the traditional coprecipitation methods, owing to the both morphology effect and synergistic effect between Co₃S₄ and MoS₂. DFT calculation studied the activation energies needed by MoS₂ and Co–Mo–S for HER and HDS, respectively. The required activation energies for C–S bond fracture and H₂ generation on Co–Mo–S structure are both obviously lower than that of MoS₂ structure. Our work reported a new method to synthesize Co–Mo–S catalysts with large surface area and numerous active sites, and further experimentally and theoretically proved Co–Mo–S structure had better catalytic activities for both HER and HDS.