Thermal resistance of fifth-instar Cydia pomonella (L.) (Lepidoptera: Tortricidae) as affected by pretreatment conditioning

Codling moth (Cydia pomonella (L.)) is targeted for postharvest control by quarantine regulations in Japan and South Korea and by phytosanitation concerns in Europe. Heat treatments may be used to control C. pomonella. But possible increase of heat resistance in insect pests, caused by pretreatment thermal conditions during harvest and storage periods, may compromise the efficacy of subsequent thermal treatments. A heating block system was used to determine the effect of pretreatment conditioning on the thermal resistance of the fifth-instar C. pomonella. Results showed that pretreatment conditioning at 35 °C for 40, 120, 360 or 1080 min significantly increased the thermal resistance of C. pomonella. Among the above conditions 35 °C for 360 min resulted in the highest heat resistance for fifth-instars. The minimum treatment times required to reach 100% mortality for 300 larvae that went through thermal conditioning at 35 °C for 360 min were 30, 7 and 3 min at 48, 50 and 52 °C, respectively, as compared with 15, 5 and 2 min at those temperatures without pretreatment conditioning. After a pretreatment at 35 °C for 360 min followed by a period of at least 120 min at 22 °C, fifth-instar thermal resistance returned to the level that had existed before pretreatment conditioning.     

Kinetic and thermodynamic study of thermal inactivation of the antimicrobial peptide P34 in milk

The knowledge on thermal inactivation of biopreservatives in a food matrix is essential to allow their proper utilisation in food industry, enabling the reduction of heating times and optimisation of heating temperatures. In this work, thermal inactivation of the antimicrobial peptide P34 in skimmed and fat milk was kinetically investigated within the temperature range of 90–120 °C. The inactivation kinetic follows a first-order reaction with k-values between 0.071 and 0.007 min⁻¹ in skimmed milk, and 0.1346 and 0.0119 min⁻¹ in fat milk. At high temperatures, peptide P34 was less resistant in fat milk, with a significant decrease in residual activity as compared with skimmed milk. At temperatures below 110 °C, the fat globules seem to have protective effect to the peptide P34. Results suggest that peptide P34 is heat stable in milk with activation energy of 90 kJ mol⁻¹ in skimmed milk and 136 kJ mol⁻¹ in fat milk.     

Degradation kinetics of anthocyanins in acerola pulp: Comparison between ohmic and conventional heat treatment

Degradation kinetics of monomeric anthocyanins in acerola pulp during thermal treatment by ohmic and conventional heating was evaluated at different temperatures (75–90 °C). Anthocyanin degradation fitted a first-order reaction model and the rate constants ranged from 5.9 to 19.7 × 10⁻³ min⁻¹. There were no significant differences between the rate constants of the ohmic and the conventional heating processes at all evaluated temperatures. D-Values ranged from 116.7 to 374.5 for ohmic heating and from 134.9 to 390.4 for conventional heating. Values of the free energy of inactivation were within the range of 100.19 and 101.35 kJ mol⁻¹. The enthalpy of activation presented values between 71.79 and 71.94 kJ mol⁻¹ and the entropy of activation ranged from −80.15 to −82.63 J mol⁻¹ K⁻¹. Both heating technologies showed activation energy of 74.8 kJ mol⁻¹ and close values for all thermodynamic parameters, indicating similar mechanisms of degradation.     

Properties of polyphenol oxidase from Anamur banana (Musa cavendishii)

Polyphenol oxidase (PPO) was extracted from Anamur banana, grown in Turkey, and its characteristics were studied. The optimum temperature for banana PPO activity was found to be 30 °C. The pH-activity optimum was 7.0. From the thermal inactivation studies, in the range 60–75 °C, the half-life values of the enzyme ranged from 7.3 to 85.6 min. The activation energy (E_a) and Z values were calculated to be 155 kJ mol⁻¹ and 14.2 °C, respectively. K_m and V_max values were 8.5 mM and 0.754 OD₄₁₀ min⁻¹, respectively. Of the inhibitors tested, ascorbic acid and sodium metabisulphite were the most effective.     

Thermal properties and resistant starch content of green banana flour (Musa cavendishii) produced at different drying conditions

The objective of this research was to verify the effect of drying conditions on thermal properties and resistant starch content of green banana flour (Musa cavendishii). The green banana flour is a complex-carbohydrates source, mainly of resistant starch, and quantifying its gelatinization is important to understand how it affects food processing and the functional properties of the flour. The green banana flour was obtained by drying unripe peeled bananas (first stage of ripening) in a dryer tunnel at 52 °C, 55 °C and 58 °C and air velocity at 0.6 m s⁻¹, 1.0 m s⁻¹ and 1.4 m s⁻¹. The results obtained from differential scanning calorimetry (DSC) curves show a single endothermic transition and a flow of maximum heating at peak temperatures from (67.95 ± 0.31) °C to (68.63 ± 0.28) °C. ANOVA shows that only drying temperature influenced significantly (P < 0.05) the gelatinization peak temperature (Tp). Gelatinization enthalpy (ΔH) varied from 9.04 J g⁻¹ to 11.63 J g⁻¹ and no significant difference was observed for either temperature or air velocity. The resistant starch content of the flour produced varied from (40.9 ± 0.4) g/100 g to (58.5 ± 5.4) g/100 g, on dry basis (d. b.), and was influenced by the combination of drying conditions: flour produced at 55 °C/1.4 m s⁻¹ and 55 °C/1.0 m s⁻¹ presented higher content of resistant starch.     

Effect of thermal treatments on the properties of coconut milk emulsions prepared with surface-active stabilizers

Previously we have demonstrated improved stability of coconut milk emulsions homogenized with various surface-active stabilizers, i.e., 1 wt% sodium caseinate, whey protein isolate (WPI), sodium dodecyl sulfate (SDS), or polyoxyethylene sorbitan monolaurate (Tween 20) [Tangsuphoom, N., & Coupland, J. N. (2008). Effect of surface-active stabilizers on the microstructure and stability of coconut milk emulsions. Food Hydrocolloids, 22(7), 1233–1242]. This study examines the changes in bulk and microstructural properties of those emulsions following thermal treatments normally used to preserve coconut milk products (i.e., −20 °C, −10 °C, 5 °C, 70 °C, 90 °C, and 120 °C). Calorimetric methods were used to determine the destabilization of emulsions and the denaturation of coconut and surface-active proteins. Homogenized coconut milk prepared without additives was destabilized by freeze–thaw, (−20 °C and −10 °C) but not by chilling (5 °C). Samples homogenized with proteins were not affected by low temperature treatments while those prepared with surfactants were stable to chilling but partially or fully coalesced following freeze–thaw. Homogenized coconut milk prepared without additives coalesced and flocculated after being heated at 90 °C or 120 °C for 1 h in due to the denaturation and subsequent aggregation of coconut proteins. Samples emulsified with caseinate were not affected by heat treatments while those prepared with WPI showed extensive coalescence and phase separation after being treated at 90 °C or 120 °C. Samples prepared with SDS were stable to heating but those prepared with Tween 20 completely destabilized by heating at 120 °C.     

Thermal inactivation of peroxidase during blanching of butternut squash

The kinetics of thermal inactivation of peroxidase in butternut squash during water blanching was studied. Thin slices of squash were immersed in water at 60-90 °C for 0-60 min. For treatments below 70 °C, a biphasic, first-order kinetics model was proposed for peroxidase inactivation that would correspond to heat-labile and heat-resistant fractions of the enzyme. Parameters of the first-order model for the heat-labile and heat-resistant fractions were k_L,ref=24.8733 min⁻¹, E_aL=14023 J/mol and k_R,ref=0.0729 min⁻¹, E_aR=15794 J/mol, respectively. For treatments above 70 °C, a monophasic first-order kinetics model was proposed. Parameters were k_ref=8.6425 min⁻¹, E_a=149900 J/mol. Decreases in ascorbic acid contents due to blanching were analyzed. Blanching processes at high temperature and short time resulted in higher ascorbic acid retention. A linear relationship between ascorbic acid retention and processing temperature was found.     

Quantification and characterisation of polyphenol oxidase from vanilla bean

Polyphenol oxidase (PPO) of Vanilla planifolia Andrews beans was extracted and purified through ammonium sulphate precipitation, dialysis, and gel filtration chromatography. PPO activity was measured by improved UV technique using 4-methylcatechol and catechol as substrates increasing substantial sensitivity of previous procedure. The optimum pH and temperature for PPO activity were found to be 3.0 and 3.4 and 37 °C, respectively. K_m and V_max values were found to be 10.6 mM/L and 13.9 OD₃₀₀ min⁻¹ for 4-methylcatechol and 85 mM/L and 107.2 OD₃₀₀ min⁻¹ for catechol. In an inhibition test, the most potent inhibitor was found to be 4-hexylresorcinol followed by ascorbic acid. The thermal inactivation curve was biphasic. Activation energy (E_a) and z values were calculated as 92.10 kJ mol⁻¹ and 21 °C, respectively.     

An experimental investigation into the pre-treatment of synthetic membranes using sodium hydroxide solutions

In this paper the effect of two pre-treatment methods are compared experimentally for the filtration of (i) a spent sulphite liquor (17.8 wt.% dry solids) using a 20 kg mol⁻¹ molar mass cut off (MMCO) fluoropolymer membrane and (ii) a molasses solution (45° Brix) using a polysulphone (Psf) membrane (1.5 μm pore size). Both feeds are industrially relevant, and subject to severe fouling issues when membranes are used in their subsequent processing. The pre-treatment methods evaluated were: (i) conditioning with water at 60 °C only [Protocol 1], and (ii) conditioning with water at 60 °C followed by cleaning with 0.5 wt.% NaOH [Protocol 2]. Results are presented that confirm the benefits of sodium hydroxide preconditioning upon performance, supporting the suggestion by some membrane manufacturers that this step be included as part of the pre-treatment protocol.     

Toxicity of ethyl formate to adult Sitophilus oryzae (L.), Tribolium castaneum (herbst) and Rhyzopertha dominica (F.)

Fumigations were conducted using a continuous flow-through laboratory process to maintain constant concentrations of ethyl formate and low levels (<0.8%) of respiratory carbon dioxide. The procedure minimised the effects of sorption by exposing test insects without media and minimised the effect of carbon dioxide by use of continuous flow. The concentration×time (Ct) products of ethyl formate for adult Sitophilus oryzae, Tribolium castaneum and Rhyzopertha dominica at 25 °C and 70% relative humidity for the 6 h exposure were, respectively: (1) LD₅₀ 107.8, 108.8 and 72.8 mg h L⁻¹ and (2) LD_99.5 207.4, 167.1 and 122.2 mg h L⁻¹. Endpoint mortality was reached within 24 h of initial exposure.     

Impact of high temperatures on efficacy of cyfluthrin and hydroprene applied to concrete to control Tribolium castaneum (Herbst)

In laboratory trials, concrete was treated with cyfluthrin wettable powder (WP) at 40 mg active ingredient [AI] cyfluthrin WP/m², then heated for 4, 8, or 16 h at either 45°C or 55°C, or treated but not heated (seven treatment combinations). Bioassays were conducted by exposing adult Tribolium castaneum (Herbst) for 0.5, 1, and 2 h. Survival of T. castaneum was generally greater on unheated concrete compared with the heating treatments, and survival appeared to decrease as heating time increased at both 45°C and 55°C. In a second laboratory trial, concrete was treated with hydroprene (Gentrol) at the label rate of 1.9×10⁻³ mg [AI]/cm², and bioassayed by exposing late-instar T. castaneum larvae on the treated surface. There were significant differences between untreated controls and the heat treatment regimes (P<0.05) with respect to the percentage of live emerged adults, the percentage of those adults with deformities, and the percentage of dead adults, but heating did not reduce efficacy of hydroprene. In a field trial, concrete was treated with cyfluthrin at 2 mg [AI] cyfluthrin WP/m², and placed in a flour mill undergoing an experimental heat treatment and in an unheated office. Treated concrete was bioassayed by continually exposing adult T. castaneum for 0.5-120 h. The effect of heating time on insect mortality was not significant (P?0.05). Except for T. castaneum exposed for 0.5 h, the percentage of beetle survival on unheated concrete was greater (P<0.05) than survival on concrete that had been heated in the mill, indicating a possible beneficial effect on cyfluthrin toxicity due to heating. Results of these studies show that short-term exposures to high temperatures may have no appreciable effect on efficacy of either cyfluthrin WP or hydroprene, and combination treatments of heat plus either of these insecticides may be effective alternatives to methyl bromide for disinfesting milling facilities.     

Optimisation of the aqueous extraction conditions of phenols from meadowsweet (Filipendula ulmaria L.) for incorporation into beverages

Meadowsweet was extracted in water at a range of temperatures (60–100 °C), and the total phenols, tannins, quercetin, salicylic acid content and colour were analysed. The extraction of total phenols followed pseudo first-order kinetics, the rate constant (k) increased from 0.09 ± 0.02 min⁻¹ to 0.44 ± 0.09 min⁻¹, as the temperature increased from 60 to 100 °C. An increase in temperature from 60 to 100 °C increased the concentration of total phenols extracted from 39 ± 2 to 63 ± 3 mg g⁻¹ gallic acid equivalents, although it did not significantly affect the proportion of tannin and non-tannin fractions. The extraction of quercetin and salicyclic acid from meadowsweet also followed pseudo first-order kinetics, the rate constant of both compounds increasing with an increase in temperature up until 90 °C. Therefore, the aqueous extraction of meadowsweet at temperatures at or above 90 °C for 15 min yields extracts high in phenols, which may be added to beverages.     

Controlling deterioration of high-moisture maize with ozone treatment

Two experiments were conducted to determine the effect of ozone treatment on controlling deterioration of high-moisture maize under extreme and moderate environmental conditions experienced during harvest. In the first experiment, 0.77-kg maize samples held at 22% moisture content were treated with ozone at 0.08, 0.16, 0.31, 0.62, 0.94, 1.25 and 1.56 mg kg maize⁻¹ min⁻¹ (60-1120 ppm ozone in air during application) for periods of 5 or 24 h, with an additional treatment of 1.56 mg min⁻¹ repeated every 3 d, and stored at 32 °C for 9 d under continuous aeration. Ozone treatment decreased dry matter loss compared to the control, but not to a level that would likely justify ozone treatment at the rates and treatment times used. In the second experiment, 2.43-kg maize samples held at 26% moisture content were treated with ozonation rates of 0.25, 0.5, 1, and 2 mg kg maize⁻¹ min⁻¹ (1090-8680 ppm ozone during application) for 24 h, stored at 15.5 °C for 30 d and passively aerated every 3 d. Additional ozone treatments at the 2 mg kg maize⁻¹ min⁻¹ rate were applied for 1 h on 3-, 6-, and 12-d intervals throughout the experiment. Single ozone treatments of 1 and 2 mg kg maize⁻¹ min⁻¹ were equally effective, reducing dry matter loss by 1.3 percentage points compared to the control after 30 d of storage. Repeat treatments at 2 mg kg maize⁻¹ min⁻¹ did not reduce dry matter loss compared to the single treatment.     

Thermal death kinetics and heating rate effects for fifth-instar Cydia pomonella (L.) (Lepidoptera: Tortricidae)

Thermal death kinetic parameters of fifth-instar codling moths (Cydia pomonella (L.)) and the effect of three heating rates (1°C min⁻¹, 10°C min⁻¹, and 18°C min⁻¹) on larval mortality were determined by a heating block system. The insects were heated to four temperatures (46°C, 48°C, 50°C, and 52°C) held for predetermined periods followed by 24 h storage at 4°C before mortality evaluation. Thermal death kinetics for fifth-instar codling moths followed a 0.5th order of kinetic reaction. Minimum time required to achieve 100% mortality of a given population decreased with temperature in a semi-logarithmic manner. No larval survival was observed in samples of 600 insects after exposure to 46°C, 48°C, 50°C, and 52°C for 50, 15, 5, and 2 min, respectively. Activation energy for thermal kill of fifth-instar codling moths at the heating rate of 18°C min⁻¹ was estimated to be about 472 kJ mol⁻¹. The lethal time accumulated during the ramp period was about 1.8, 0.2, and 0.1 min for the heating rates of 1°C min⁻¹, 10°C min⁻¹, and 18°C min⁻¹, respectively.     

Modelling heat-disinfestation of dried fruits on “biological model” larvae Ephestia kuehniella (Zeller)

The effects of heat treatment on the survival of isolated Ephestia kuehniella Zeller larvae were examined. Larvae were treated in a specific device at a temperature range of 46 to 70 °C. Statistical analysis of the data demonstrated that the thermal survival kinetics was best represented by a 2-parameter Weibull model above 50 °C. The mortality of larvae only occurs beyond a critical temperature of 41.6 °C ± 2.5 °C. A 2D axial-symmetric model of heat transfer (convection, microwave at 915 MHz) was developed for cocoa bean and date palm. It was combined with the survival rate of larvae (Weibull model) and some z-values (from literature) are used for calculating a “food quality index” degradation kinetics. The intensive heating/convection process may not be adaptable for food products at low water activity due to high surface product temperatures. The use of microwave heating for date fruits and conventional hot air treatments for cocoa beans is recommended.     

Effects of temperature,solid content and pH on the stability of black carrot anthocyanins

Anthocyanin stability of black carrots was studied at various solid contents (11, 30, 45 and 64° Brix) and pHs (4.3 and 6.0) during both heating, at 70–90 °C, and storage at 4–37 °C. Monomeric anthocyanin degradation fitted a first-order reaction model. Degradation of monomeric anthocyanins increased with increasing solid content during heating, while it decreased during storage. For example, at pH 4.3, half-life periods for anthocyanins at 30, 45 and 64° Brix were, respectively, 8.4, 6.9 and 5.2 h during heating at 80 °C and 18.7, 30.8 and 35.9 weeks during storage at 20 °C. At 30–64° Brix, increasing pH from 4.3 to 6.0 enhanced the degradation of anthocyanins during heating. The effect of pH on thermal stability of anthocyanins was also studied at six different pHs (2.5–7.0) in citrate-phosphate buffer solutions and significant decrease in anthocyanin stability was observed at pHs above 5.0. Higher activation energies (E_a) were obtained during heating than during storage with increasing solid contents. At 30–64° Brix, E_a values ranged from 68.8 to 95.1 kJ mol⁻¹ during heating and from 62.1 to 86.2 kJ mol⁻¹ during storage. Q₁₀ values at 20–37 °C were as high as 3.1 at 45° Brix and 3.6 at 64° Brix.     

Kinetics of tocols degradation during the storage of einkorn (Triticum monococcum L. ssp. monococcum) and breadwheat (Triticum aestivum L. ssp. aestivum) flours

The kinetics of tocols degradation in wholemeal and white flours from einkorn cv Monlis and bread wheat cv Serio were studied during storage at five different temperatures (−20, 5, 20, 30 and 38 °C) up to 242 days. Tocols decreased as a function of time and temperature, following first-order kinetics. Degradation rates and their dependence upon temperature were similar for the two Triticum species studied. Tocols decrease was quicker in white flour than in wholemeal flour (on average for total tocols at 38 °C, k = 7.79 × 10⁻³ days⁻¹ vs 3.15 × 10⁻³ days⁻¹, respectively). The temperature-dependent degradation was similar for all homologues (Ea = 34.3–49.4 kJ/mol) except for α-T, less thermostable in white flours (Ea = 61.2 kJ/mol in einkorn and Ea = 54.7 kJ/mol in bread wheat).     

Sensitivity analysis of continuous ohmic heating process for multiphase foods

The process sensitivity analysis of continuous Ohmic heating process for soup products containing large particulates was performed by use of a validated computer modeling package to determine the critical control factors and their acceptable control ranges under given control targets. The major processing variables investigated included electrical conductivities of carrier fluid and particles, particle thermal diffusivity, surface heat transfer coefficient, particle size, particle concentration, flow rate, and initial product temperature. The response variables as the indicators of effects from processing variable deviations were the process temperatures and accumulated lethality values for both carrier fluid and particles at the end of holding tube. The results demonstrated that under giving base processing conditions with a control target process temperature of 133 °C (the carrier fluid temperature at the entrance of the holding tube or the end of heating tube), increasing carrier fluid electrical conductivity from 1.42 to 2.13 S/m at a reference temperature of 70 °C, particle size from 16 to 24 mm, and flow rate from 1600 to 2400 L/h could result in lower particle center temperature at the end of holding tube, while increasing particle electrical conductivity from 0.96 to 1.44 S/m at a reference temperature of 70 °C, thermal diffusivity from 1.16 × 10⁻⁷ to 1.74 × 10⁻⁷ m²/s, surface heat transfer coefficient from 112 to 168 W/°C/m², particle concentration from 52% to78%, and initial product temperature from 56 to 84 °C could generate higher particle center temperature. Within the variable deviation ranges investigated, the importance order of effects of major processing variables were determined with respect to the particle center temperatures, carrier fluid temperatures and accumulated lethality values. The acceptable deviation ranges were built up for six major processing variables under meeting the required target Fo (at the particle center) values. The information and knowledge obtained from this study can be useful for understanding how major processing variables of continuous Ohmic heating processing system affect the required process target variables and the methodology developed in this study can be further used as a protocol for both process establishment and optimization purposes.     

Characterization of polyphenol oxidase from butter lettuce (Lactuca sativa var. capitata L.)

Polyphenol oxidase (PPO) was isolated from butter lettuce (Lactuca sativa var. capitata L.) grown in Poland and its biochemical characteristic were studied. PPO from butter lettuce showed a higher affinity to 4-methylcatechol than to catechol. The K_M and V_max values were: 3.20 ± 0.01 mM and 4081 ± 8 U/ml min⁻¹ for catechol and 1.00 ± 0.09 mM and 5405 ± 3 U/ml min⁻¹ for 4-methylcatechol. The optimum pHs of the enzyme were found to be 5.5 using catechol and 6.8 using 4-methylcatechol as substrate. The enzyme had a temperature optimum of 35 °C. The enzyme was relatively stable at 30 °C and 40 °C. The times required for 50% inactivation of activity at 50 °C, 60 °C and 70 °C were found to be about 30, 20 and 5 min, respectively. Inhibitors used for investigation in this study were placed in relative order of inhibition: p-hydroxybenzoic acid > glutathione ≈ ascorbic acid > l-cysteine > EDTA > citric acid. The enzyme eluted in the chromatographic separations was analyzed electrophoretically under denaturating conditions. The analysis revealed a single band on the SDS–PAGE which corresponded to a molecular weight of 60 kDa.