Novel all-solid-state copper(II) microelectrode based on a dithiomacrocycle as a neutral carrier

A novel dithiomacrocycle (4-phenyl-11-decanoyl-1,7-dithia-11-azacyclotetradecane-4-sulfide) has been synthesized and used as a new ionophore in order to develop a plasticized poly(vinyl chloride) membrane for copper ion detection. The performance of these novel planar copper(II)-selective potentiometric microelectrodes was investigated using potentiometric measurements. The developed microelectrodes exhibits a good linear response of 29.5 ± 1 mV per decade within the concentration range of 1.0 × 10⁻⁶ to 1.0 × 10⁻² M (r = 0.9995) of Cu²⁺. The detection limit was determined as 5.62 × 10⁻⁷ M and the selectivity coefficients for possible interfering cations were evaluated. The microelectrodes are suitable for use with aqueous solutions of pH 3.5-6.0 and were found to be insensitive to the nature of the anions used in the sample.     

Plastic membrane electrodes for the determination of flavoxate hydrochloride and cyclopentolate hydrochloride

Four novel ion-exchangers (Fx-Rt (I), Fx-TPB (II), Cp3-PMA (III) and Cp3-PTA (IV)) of antispasmodic and anticholinergic drugs, flavoxate hydrochloride (FxCl), 2-piperidinoethyl-3-methyl-4-oxo-2-phenyl-4h-1-benzopyran-8-carboxylate hydrochloride, cyclopentolate hydrochloride (CpCl) and (2-(dimethylamino)ethyl (RS)-(1-hydroxycyclopentyl)phenylacetate) hydrochloride were synthesized and incorporated into poly(vinyl chloride)-based membrane electrodes for the quantification of FxCl and CpCl in different pharmaceutical preparations. The influence of membrane composition on the potentiometric response of the membrane electrodes was found to substantially improve the performance characteristics. The best performance was reported with membranes having compositions (w/w) of Fx-Rt (2%):PVC (49%):DOP (49%), Fx-TPB (7%):PVC (46.5%):DOP (46.5%), Cp3-PMA (8%):PVC (46%):DOP (46%) and Cp3-PTA (9%):PVC (45.5%):DOP (45.5%). The proposed sensors exhibited Nernstian responses in the concentration ranges of 1.39 × 10⁻⁶-5.00 × 10⁻⁴, 9.90 × 10⁻⁷-3.75 × 10⁻⁵, 1.39 × 10⁻⁵-2.53 × 10⁻³ and 3.21 × 10⁻⁶-8.62 × 10⁻⁴ M, with detection limits of 5.50 × 10⁻⁷, 9.8 × 10⁻⁷, 9.8 × 10⁻⁶ and 2.95 × 10⁻⁶ M for the (I), (II), (III) and (IV) electrodes, respectively. The membrane electrodes performed satisfactorily over pH ranges of 2.0-5.5, 2.0-5.5, 2.0-5.0 and 2.0-7.5, with fast response times of 20, 30, 15 and 20 s for the (I), (II), (III) and (IV) electrodes, respectively. The practical utility of the sensors was demonstrated by the determination of FxCl and CpCl in pure solutions and pharmaceutical preparations using standard additions and potentiometric titration.     

A novel potentiometric sensor for promethazine based on a molecularly imprinted polymer (MIP): The role of MIP structure on the sensor performance

A novel potentiometric sensor based on a molecularly imprinted polymer (MIP) for determination of promethazine (PMZ) was prepared. Promethazine MIP particles were prepared and dispersed in 2-nitrophenyloctyl ether and then embedded in a polyvinyl chloride matrix. The effect of the monomers type on the sensor performance was investigated, and an important role for this parameter was shown. It was shown that the membrane electrode with a MIP prepared by vinylbenzene and divinylbenzene had a better performance in comparison to membrane electrodes containing MIPs prepared with methacrylic acid-ethylene glycol dimethacrylate or vinylbenzene-ethylene glycol dimethacrylate. After optimization, the membrane electrode constructed with a MIP of vinylbenzene-divinylbenzene exhibited a Nernstian response (31.2 ± 1.0 mV decade⁻¹) over a wide concentration range, from 5.0 × 10⁻⁷ to 1.0 × 10⁻¹ M, with a low detection limit of 1.0 × 10⁻⁷ M and a response time of ∼50 s. The method has the requisite accuracy, sensitivity and precision to assay PMZ in syrup samples and biological fluids.     

Preparation of Cerium (III) 12-tungstophosphoric acid/ordered mesoporous carbon composite modified electrode and its electrocatalytic properties

In this work, a novel structured Cerium (III) 12-tungstophosphoric acid (CePW)/ordered mesoporous carbon (OMC) composite is synthesized. The characterization of the material by the Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and electrochemical characterization shows that the novel CePW/OMC composite has improved properties based on the combination of CePW and OMC properties. CePW/OMC can be used to modify the glassy carbon (GC) electrode and the CePW/OMC/GC modified electrode shows an enhanced electrocatalytic activity. This property can be applied in the determination of some biomolecules. Especially, the detection and determination of the guanine (G) in the presence of adenine (A) is achieved. The catalytic current of G versus its concentration shows a good linearity with two good linear ranges from 4.0 × 10⁻⁶ to 8.0 × 10⁻⁵ M and from 8.0 × 10⁻⁵ to 1.9 × 10⁻³ M (correlation coefficient = 0.999 and 0.996) with a detection limit of 5.7 × 10⁻⁹ M (S/N = 3). The linear range for adenine is 4.0 × 10⁻⁶-7.0 × 10⁻⁴ M with a detection limit of 7.45 × 10⁻⁸ M. With good stability and reproducibility, the present CePW/OMC/GC modified electrode should be a good model for constructing a novel and promising electrochemical sensing platform for further electrochemical detection of other biomolecules.     

A potentiometric and voltammetric sensor based on polypyrrole film with electrochemically induced recognition sites for detection of silver ion

Conducting polypyrrole membranes were deposited on glassy carbon electrodes by electropolymerizing pyrrole in the presence of Eriochrome Blue-Black B (EBB) as the counter anion. The electrodes were then subjected to several oxidation/reduction potential steps in pure silver nitrate solution for successive accumulation/stripping of silver species. This electrochemically mediated doping/templating generated selective recognition elements in the EBB/PPy film for silver ions. The resulting sensor exhibited a considerable enhancement in the potentiometric and voltammetric response characteristics: extending the linear dynamic range and lowering the detection limit. In the potentiometric mode, the sensor showed highly reproducible response with a Nernstian slope of 58.5 ± 0.3 mV per decade of Ag⁺ activity over a linear range spanning seven orders of magnitude (1 × 10⁻⁸ to 1 × 10⁻¹ M Ag⁺), with a detection limit of ∼6 × 10⁻⁹ M. The electrodes demonstrated high selectivity over a large number of cations including alkali, alkaline earth and several transition and heavy metal ions, and could be used over a wide pH range of 1-8.5. The EBB/PPy modified electrode was also used for preconcentration and differential pulse anodic stripping voltammetric (DPASV) measurements. The DPASV peak current was dependent on the concentration of Ag⁺ over the range 3 × 10⁻¹⁰ to 1 × 10⁻⁴ M. The presence of 1000-fold excess of Cd²⁺, Cu²⁺, Cr³⁺, Co²⁺, Mn²⁺, Fe²⁺, Fe³⁺, Ni²⁺ and Pb²⁺ can be tolerated in the determination of silver ion.     

Application of surfactant modified zeolite carbon paste electrode (SMZ-CPE) towards potentiometric determination of sulfate

A sulfate-selective electrode based on surfactant modified zeolite (SMZ) particles into carbon paste has been proposed (SMZ-CPE). The electrode was fully characterized in terms of composition, response time, ionic strength range, thermal stability and usable pH range. The electrode containing 10% of the SMZ was exhibited linear response range to sulfate species in the range of 2.0 × 10⁻⁶-3.1 × 10⁻³ M with detection limit of 2.0 × 10⁻⁶ M and Nernstian slope of 29.8 ± 0.8 mV per decade of sulfate concentration. The electrode response remains constant in the pH range of 4-10 and in the presence of 1 × 10⁻⁴-2 × 10⁻³ M NaNO₃. The response of the electrode reaches equilibrium within several second after immersing the electrode in sulfate solution. A successful application of sulfate determination sulfate in real sample of a pharmaceutical zinc sulfate capsule, using direct potentiometry, is presented. The electrode was also used for potentiometric titration of sulfate. The validation of the obtained results in each case was proved by statistical methods.     

Direct determination of aluminium in foods and pharmaceutical preparations by potentiometry using an AlMCM-41 modified polymeric membrane sensor

A potentiometric aluminium sensor, based on the use AlMCM-41 as a neutral carrier, in poly(vinyl chloride) (PVC) matrix, is reported. The sensor exhibits significantly enhanced selectivity toward Al³⁺ ions over the concentration range 1.0 × 10⁻⁷ to 1.0 × 10⁻¹ M with a detection limit of 8.6 × 10⁻⁸ M and a Nernstian slope of 19.5 ± 0.4 mV/decade of activity. The best performance was obtained with membrane composition 30% poly(vinyl chloride), 67% acetophenone, 3% ionophore and 2 mL tetrahydrofuran. Fast and stable response, good reproducibility and long-term stability are demonstrated. The response time of the sensor is ∼10 s and membrane could be used over a period of 3 months without any considerable divergence in potentials. Selectivity coefficients were determined by matched potential method (MPM). The AlMCM-41-based sensor is suitable for use in aqueous solution of pH 3-6. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal coefficient of the electrode. It was used to determine Al³⁺ in drugs and food products.     

Polyvinylidene fluoride and polyetherimide hollow fiber membranes for CO2 stripping in membrane contactor

Porous polyvinylidene fluoride (PVDF) and polyetherimide (PEI) hollow fiber membranes incorporating polyethylene glycol (PEG) were prepared via spinning process for CO₂ membrane stripping. CO₂ loaded diethanolamine solution was used as liquid absorbent while N₂ was used as a strip gas. The characterization study of the fibers was carried out in terms of permeation test, contact angle measurement and liquid entry pressure (wetting pressure). Performance study via membrane contactor stripping was carried out at specific operating condition. The experimental results showed that PVDF membrane have high gas permeation, effective surface porosity and contact angle despite having lower liquid entry pressure in comparison with PEI membrane. PVDF-PEG membrane showed the highest stripping flux of 4.0 × 10⁻² mol m⁻² s⁻¹ at 0.7 ms⁻¹ compared to that of PEI membrane. Although the stripping flux for PEI-PEG membranes was slightly lower than PVDF membrane (e.g. 3.5 × 10⁻² mol m⁻² s⁻¹ at liquid velocity of 0.85 ms⁻¹), the membrane wetting pressure of PEI membrane is higher than hydrophobic PVDF membrane. Long term performance of both membranes showed severe flux reduction but started to level-off after 30 h of operation.     

Cu(II) complexes as receptor molecules for development of new chloride sensors

Highly sensitive and selective chloride polymeric membrane sensors are developed that employ Cu(II) complexes as anion carriers. Optimized membrane sensors showed a near-Nernstian response towards chloride anion over a wide concentration range of 2.5 × 10⁻⁵ to 1.0 × 10⁻¹ M and have micromolar level detection limits. These sensors have fast response time and work well in the pH range of 4.2-9.6. They exhibited enhanced potentiometric selectivity for chloride over other anions, including more lipophilic anions such as perchlorate, thiocyanate, nitrate, etc. Response characteristics (e.g. detection limit, linear range, response slope and selectivity) of these sensors remain essentially the same over a period of ∼5 months, reflecting remarkable stability.     

Preparation and characterization of thiocyanate-selective electrodes based on new complexes of copper(II) as neutral carriers

The complexes of hydroxycitronellal (o-aminobenzoic acid) copper(II) (Cu(II)-HXAB) and salicylaldehyde (o-aminobenzoic acid) copper(II) (Cu(II)-SHAB) were used as neutral carriers in PVC-based membrane ion-selective electrodes. The electrode based on Cu(II)-HXAB exhibited near-Nernstian potential response to thiocyanate (SCN⁻) in a linear range of 1.0 × 10^− 6 to 1.0 × 10^− 1 M with a detection limit of 8.5 × 10^− 7 M and a slope of − 57.3 mV/decade in 0.01 M phosphate buffer solution (pH 5.0). The electrode exhibited high selectivity to SCN⁻ over other tested anions with an anti-Hofmeister selectivity sequence. The selectivity behavior might be discussed in terms of UV-Vis spectrum and infrared spectrum. The transfer process of thiocyanate across the membrane interface was investigated by making use of the AC impedance technique. The electrode containing Cu(II)-HXAB could be applied to thiocyanate analysis in waste water with satisfactory results.     

A glassy carbon supported bilayer lipid-like membrane of 5,5-ditetradecyl-2-(2-trimethyl-ammonioethyl)-1,3-dioxane bromide for electrochemical sensing of epinephrine

A self-assembled bilayer lipid-like membrane (BLM) supported on glassy carbon electrode (GCE) was fabricated using 5,5-ditetradecyl-2-(2-trimethyl-ammonioethyl)-1,3-dioxane bromide (DTDB) for epinephrine (EP) determination in the presence of ascorbic acid (AA). This modified electrode (DTDB/GCE) has strong membrane adsorption accumulation and electrocatalytic ability toward EP and AA. The oxidation of EP was controlled by double step adsorption accumulation process of the DTDB-BLM. The parameters of fitted Langmuir isotherm Γ_max, B_ADS, and ΔG_ADS values were determined as 1.0×10⁻¹¹ mol cm⁻², 2.04×10⁶ dm³ mol⁻¹, and −45.17 kJ mol⁻¹ for the fist step for EP concentration less than 1 mM, and 4.92×10⁻¹¹ mol cm⁻², 7.35×10⁴ dm³ mol⁻¹, and −37.1 kJ mol⁻¹ for the second step for EP concentration higher than 1 μM. The DPV peaks for EP and AA oxidations were appeared at 0.220 and 0.085 V versus SCE, respectively, allowing the determination of EP in the presence of high concentration of AA. The advantage of DTDB-BLM was demonstrated experimentally in comparison with other three BLMs, and attributed to the dioxane group as well as the suitable length of the carbon chain of DTDB molecule. The current response of the DTDB/GCE was fast and reproducible, suitable for the electrochemical sensing in flow-injection systems. A linear range of 1×10⁻⁸ to 1×10⁻⁴ M EP was preliminary obtained using a simple setup.     

Chloride selective potentiometric sensor based on a newly synthesized hydrogen bonding anion receptor

A new potentiometric chloride sensor based on the use of anion receptor 2-(1-H-imidazo [4,5-f][1,10]phenanthroline-2-yl)-6methoxyphenol (HIPM) in poly(vinyl chloride) (PVC) matrix is reported. Effect of various plasticizers: 2-nitrophenyloctylether (o-NPOE), di-n-butylphthalate (DBP), diethyl phthalate (DEP), dioctylpthalate (DOP), tri-n-butyl phosphates (TBP), chloronapthalene (CN) and cation excluder, cetryltrimethylammoniumbromide (CTAB) was studied. The best performance was obtained with a membrane composition of PVC: o-NPOE:HIPM: CTAB ratio (w/w, %) of 31:60:7:3. The sensor exhibits significantly enhanced selectivity towards chloride over the concentration range 5.0 × 10⁻⁸ to 1.0 × 10⁻¹ M with a lower detection limit of 1.0 × 10⁻⁸ M and a Nernstian slope of 59.8 mV decade⁻¹ of activity. Influence of the membrane composition and possible interfering ions was investigated on the response properties of the electrode. Fast and stable response, good reproducibility and long-term stability are demonstrated. The sensor shows response time of <10 s and can be used for about 3 months without any considerable divergence in their potential response. Selectivity coefficients determined with matched potential method (MPM) indicate high selectivity for chloride. The proposed electrode shows fairly good discrimination of chloride from anions. It was successfully applied to determination of chloride ion in packed drinking water. The electrode can be used in the pH range of 6.5-8.0 and mixtures containing up to 20% (v/v) non-aqueous content. It was used as an indicator electrode in potentiometric titration of chloride ion against silver nitrate.     

Drug selective poly(vinyl chloride)-based sensor of desipramine hydrochloride

The novel ion-pair ([TPB]⁻ [DH]⁺) of the quaternary ammonium drug desipramine hydrochloride, 3-(5,6-dihydrobenzo[b][1]benzazepin-11-yl)-N-methylpropan-1-amine, has been synthesized and incorporated into a poly(vinyl chloride)-based membrane sensor for the quantification of desipramine hydrochloride in different pharmaceutical preparations. The influence of the membrane composition on the potentiometric responses of the membrane sensor has been found to substantially improve the performance characteristics. The best performance was reported with membranes having the composition (in mg) of ([TPB]⁻ [DH]⁺) (5): PVC (150): o-NPOE (150). The proposed sensor (sensor no. 4) exhibits a Nernstian response in the concentration range of 2.2 × 10⁻⁶ to 1.0 × 10⁻² M with a detection limit of 1.2 × 10⁻⁶ M. The membrane sensor performs satisfactorily over the pH range of 2.8-7.4 with a fast response time of 12 s. The sensor no. 4 can tolerate a non-aqueous content of up to 20% and can be utilized for the determination of drug concentration in pharmaceutical preparation (tablets) and in body fluids such as urine and blood samples. The results were comparatively evaluated with liquid chromatography (LC). It was observed that the concentration of drug was greater in the blood sample than in the urine sample, as most of the drug is metabolized in the liver before discharge to urine.     

Aluminium (III)-selective PVC membrane sensor based on a Schiff base complex of N,N′-bis (salicylidene)-1, 2-cyclohexanediamine

A potentiometric aluminium sensor, based on the use N,N′-bis(salicylidene)-1,2-cyclohexanediamine (NBSC) as a neutral carrier, in poly(vinyl chloride) (PVC) matrix, is reported. Effect of various plasticizers; 2-nitrophenyloctylether (o-NPOE), tri-n-butyl phosphates (TBP), dioctylpththalate (DOP) & chloronapthalen (CN), and anion excluder, sodium tetraphenylborate (NaTPB) was studied. The best performance was obtained with a membrane composition of PVC: o-NPOE: NBSC: NaTPB ratio (w/w; mg) of 150:150:5:5. The sensor exhibits significantly enhanced selectivity toward Al³⁺ ions over the concentration range 1.0 × 10⁻⁸-1.0 × 10⁻¹ M with a lower detection limit of 5.0 × 10⁻⁹ M and a Nernstian slope of 20.3 ± 0.1 mV decade⁻¹ of activity. Influence of the membrane composition and possible interfering ions was investigated on the response properties of the electrode. Fast and stable response, good reproducibility and long-term stability are demonstrated. The sensor shows response time of <5 s and can be used for about 3 months without any considerable divergence in their potential response. Selectivity coefficients determined by matched potential method (MPM) indicate high selectivity for aluminium (III) ion. The proposed electrode shows fairly good discrimination of aluminium (III) from many metal ions. It was successfully applied for direct determination of aluminium (III) in biological, industrial and environmental samples. The electrode can be used in the pH range of 2.0-9.0 and mixtures containing up to 20% (v/v) non-aqueous content. It was used as an indicator electrode in potentiometric titration of aluminium ion vs. EDTA.     

High sensitive simultaneous determination of catechol and hydroquinone at mesoporous carbon CMK-3 electrode in comparison with multi-walled carbon nanotubes and Vulcan XC-72 carbon electrodes

The simultaneous voltammetric determination of catechol (CC) and hydroquinone (HQ) has been achieved at a mesoporous carbon CMK-3 modified electrode in phosphate buffer solution (pH 7.0). At the electrode both CC and HQ can cause a pair of quasi-reversible and well-defined redox peaks and their peak potential difference increases. In comparison with multi-walled carbon nanotubes (MWCNTs) and Vulcan XC-72 carbon modified electrodes the CMK-3 modified electrode shows larger peak currents and higher adsorbed amounts for the two dihydroxybenzene isomers. This is related to the higher specific surface area of CMK-3. Under the optimized conditions, the linear concentration ranges for CC and HQ are 5 × 10⁻⁷ to 3.5 × 10⁻⁵ M and 1 × 10⁻⁶ to 3 × 10⁻⁵ M, respectively. In the presence of 5 μM isomer, the linear concentration range of CC (or HQ) is 5 × 10⁻⁷ to 2.5 × 10⁻⁵ M (or 5 × 10⁻⁷ to 2.0 × 10⁻⁵ M). The sensitivity for CC or HQ is 41 A M⁻¹ cm⁻² or 52 A M⁻¹ cm⁻², which is close to that without isomer. The detection limits (S/N = 3) for CC and HQ are 1 × 10⁻⁷ M after preconcentration on open circuit for 240 s.     

Microfabrication, characterization and analytical application of a new thin-film silver microsensor

The present research demonstrates the microfabrication of a novel thin-film silver microelectrode based on an ion-selective PVC organic membrane. First, the gold substrate thin-film surface is treated by depositing a thin-layer of Ag electrochemically. This pretreatment step is followed by applying the organic-membrane-sensitive layer using a new nebulization technique, which gives a high stability to the organic-membrane-sensitive layer. The performance of the resulting thin-film silver microelectrode is investigated by potentiometric measurements. The microelectrode provides a linear Nernstian response of high sensitivity (58 ± 0.5 mV/decade) covering the range of 1 × 10⁻⁶-1 × 10⁻¹ mol L⁻¹ of Ag⁺ ions with a fast response time (<20 s) and a relatively long life span (>3 months). The suggested microelectrode is successfully used in the analytical evaluation of Cl⁻ ions in some real environmental samples as well as in the simultaneous determination of halides using potentiometric titration. The results obtained are compared with those obtained by the commercial silver billet electrode and the conventional bulk ion-selective electrode based on the same ionophore.     

Potentiometric sensor for polyethoxylated nonionic surfactant determination

A new liquid membrane surfactant sensor based on a 1,3-didecyl-2-methylimidazolium-tetraphenylborate ion-exchange complex was tested in different ethoxylated nonionic surfactants (EONS) and polyethylene glycols. The sensor also responded to tetraphenylborate (slope = −56.1 ± 0.8 mV/decade of activity) in the 1 × 10⁻⁶ to 2 × 10⁻³ M concentration range.The selectivity performance of the sensor toward alkaline, alkaline earth, and heavy metal cations was investigated. The sensor exhibited a fast response (within a few seconds), when in solution with some metal cations, for a 10-fold concentration change of Triton X-100. Its main application is in indicating the end-point in a potentiometric titration of EONS using sodium tetraphenylborate as the titrant. Several pure and technical grade EONS and polyethylene glycols were successfully titrated. The sensor can be used for titrations within a pH range of 3-11.The resulting potentiometric titration curves revealed an analytically usable inflection for all investigations, enabling reliable equivalence point detection using the first derivative method.The sensor was also applied to the study of barium ion reaction stoichiometry and Triton X-100 pseudoionic complex formation, as well as its reaction with tetraphenylborate.     

Highly salicylate-selective membrane electrode based on a new thiomacrocyclic Schiff base complex of binuclear copper(II) as neutral carrier

New binuclear metallic complexes of thiomacrocyclic Schiff base, 3,9,13,19 -tetraphenyl-6,16-dithione-1,11-dithio-4,5,7,8,14,15,17,18-octaazacycloeicosa-3,8,13,18-tetraene binuclear metal(II) [M(II)₂-TDDOCT] (M = Cu, Co, Ni), were synthesized and their anion response characteristics were investigated. The performances of the electrodes are considerably influenced by the nature of the central metals. The Cu(II) complex-based electrode exhibited a good selectivity to salicylate anion with an anti-Hofmeister selectivity pattern: Sal⁻ > ClO₄⁻ > SCN⁻ > I⁻ > Benzoate > B_r⁻ > Acetate > F⁻ > SO₃²⁻ > NO₂⁻ > Cl⁻ > NO₃⁻ > SO₄²⁻ > H₂PO₄⁻. The electrode had an excellent linear response to Sal⁻ from 9.0 × 10^− 7 to 1.0 × 10^− 1 M with a slope of − 59.3 mV per decade,a detection limit of 5.0 × 10^− 7 M, and a fast response time within 15 s over the entire concentration series in phosphate buffer solutions of pH 5.0 at 25 °C. Spectroscopic techniques and the influence of lipophilic charged additives on the electrode behavior were used to investigate the response mechanism to Sal⁻. The electrode can be applied to the direct determination of salicylate in human urine and pharmaceutical samples and the results obtained are in accord with the results from a standard method.     

PVC membrane and coated graphite potentiometric sensors based on 1-phenyl-3-pyridin-2-yl-thiourea for selective determination of iron(III)

The construction and performance characteristics of PVC membrane (PME) and coated graphite (CGE) Fe³⁺ ion selective electrodes based on 1-phenyl-3-pyridin-2-yl-thiourea (PPT) are described. The electrodes exhibit a Nernstian slope of 20.2 ± 0.8 (CGE) and 19.9 ± 0.4 (PME) mV decade⁻¹ of activity in Fe³⁺ ion over a wide concentration range from 3.0 × 10⁻⁷ to 1.0 × 10⁻² M for CGE and 6.9 × 10⁻⁷ to 1.0 × 10⁻² M Fe³⁺ for PME. The lower detection limits by CGE and PME are 2.0 × 10⁻⁷ and 3.9 × 10⁻⁷ M, respectively, in the pH range of 1.8-5.6 for PME and 1.8-5.8 for CGE with a fast response time (<10 s). The standard electrode potentials were determined at different temperatures and used to calculate the isothermal coefficient of the PME. The PME showed the working temperature range of 22-55 °C with isothermal temperature coefficient of 1.33 × 10⁻³ V/°C and it was also used in non-aqueous solvents. The electrodes were successfully applied to determine iron(III) in water samples.     

Enhancement of electrochemiluminesence of lucigenin by ascorbic acid at single-wall carbon nanotube film-modified glassy carbon electrode

The electrochemiluminescent behavior of lucigenin on a single-wall carbon nanotube/DMF film-modified glassy carbon electrode was studied in this paper. Comparing with the bare glassy carbon electrode, the electrochemiluminescent of lucigenin at modified electrode is more stable and without tedious procedure for clean-up the surface of modified electrode. It has been found that ascorbic acid could enhance the electrochemiluminescent intensity of lucigenin greatly at this modified electrode. Based on which, a new sensitive and simple electrochemiluminescent method for determination of ascorbic acid could be developed. The condition for the determination of ascorbic acid was optimized. Under the optimized condition, the enhanced electrochemiluminescent intensity versus ascorbic acid concentration was linear in the range of 1.0 × 10⁻⁸ to 4.0 × 10⁻⁶ mol/L with a detection limit of 2.0 × 10⁻¹⁰ mol/L, and the relative standard derivation for 1.0 × 10⁻⁷ mol/L ascorbic acid was 3.8% (n = 8). The possible mechanism was also discussed.