Characterization of MgxM2 − xP2O7 (M = Cu and Ni) solid solutions

In this study, Mg_xM_2 − xP₂O₇ (M = Cu, Ni; 0 ≤ x ≤ 2) and Mg_3 − yNi_y(PO₄)₂ (0 ≤ y ≤ 3) compositions were synthesized by the chemical coprecipitation method and characterized by X-ray diffraction, UV-vis-NIR spectroscopy and CIE L* a* b* (Commission Internationale de l’Eclairage L* a* b*) parameters measurements.Solid solutions with α-Cu₂P₂O₇ and α-Ni₂P₂O₇ structures and solid solutions with Ni₃(PO₄)₂ structure were obtained from diphosphate and orthophosphate compositions respectively. Isostructurality of α-Ni₂P₂O₇ and α-Mg₂P₂O₇ structures enlarges the compositional range of solid solution formation respect to the Mg_xCu_2 − xP₂O₇ solid solutions one.The CIE L* a* b* parameters in Mg_xNi_2 − xP₂O₇ samples were obtained comparable with these parameters in others yellow materials suitable for ceramic pigments. Mg_0.5Ni_1.5P₂O₇ composition fired at 800 °C or 1000 °C is the optimal composition to obtain yellow materials with α-diphosphate structure in conditions of this study.     

Microwave dielectric properties of the (1 − x)Mg2TiO4-xCaTiO3-y wt.% ZnNb2O6 ceramics system

Composite ceramics based on (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12-0.16, y = 0-8) were prepared by a conventional mixed-oxide route. Zn²⁺ partially replaced Mg²⁺ in Mg₂TiO₄ and formed the spinel-structured (Mg_1−δZn_δ)₂TiO₄ phase. Nb²⁺, is known to be solid soluble in CaTiO₃, was found to change its shape from cubic to pliable. A bi-phase system (Mg_1−δZn_δ)₂TiO₄ and CaTiO₃ exhibited in all samples, where a small amount of second phase Mg_1−δZn_δTiO₃ was also detected. The microwave dielectric properties of specimens were strongly related to ZnNb₂O₆ and CaTiO₃ content. As y increased, ?_r and τ_f decreased, however, Q × f decreased to a minimum value and started to increase thereafter. It was also found that ?_r and τ_f increased and Q × f decreased with increasing x. The optimized microwave dielectric properties with ?_r = 18.37, Q × f = 31,027 GHz (at 6 GHz), and τ_f = 0.51 ppm/°C were achieved for (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12, y = 4) sintered at 1360 °C for 6 h.     

Synthesis and electrical conductivity of La-Sr-X-Mg-O (X = Ti, Zr, Al) perovskite solid solution

Perovskite solid solutions of (La_0.6Sr_0.4)(X_1−yMg_y)O_3−δ (X = Ti, Zr, Al) were prepared by a coprecipitation method using corresponding aqueous solutions and ammonium carbonate solution. The freeze-dried powders were sintered in air at 1000-1500 °C for 1-36 h. Single phase solid solutions were produced in the compositions of (La_0.6Sr_0.4)(Zr_0.6Mg_0.4)O_3−δ and (La_0.6Sr_0.4)(Al_0.9Mg_0.1)O_3−δ where (3 − δ) < 3. For the compositions of X = Ti and Zr for y = 0.1 where (3 − δ) > 3, two phases including perovskite solid solution were produced at 1400-1500 °C. The stability of perovskite solid solution was closely related to the fraction of lattice oxygen atom (3 − δ). A relatively high conductivity was measured for (La_0.6Sr_0.4)(Al_0.9Mg_0.1)O_3−δ (σ = 4.15 × 10⁻⁴ S/cm at 600 °C, activation energy 113.4 kJ/mol). The influence of fraction of oxide ion vacancy on the activation energy was small for δ = 0.1-0.3 of perovskite solid solution.     

One-step electrochemical preparation of the ternary (BixSb1−x)2Te3 thin films on Au(1 1 1): Composition-dependent growth and characterization studies

This study reports on the synthesis of ternary semiconductor (Bi_xSb_1−x)₂Te₃ thin films on Au(1 1 1) using a practical electrochemical method, based on the simultaneous underpotential deposition (UPD) of Bi, Sb and Te from the same solution containing Bi³⁺, SbO⁺, and HTeO₂⁺ at a constant potential. The thin films are characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) and reflection absorption-FTIR (RA-FTIR) to determine structural, morphological, compositional and optic properties. The ternary thin films of (Bi_xSb_1−x)₂Te₃ with various compositions (0.0 ≤ x ≤ 1.0) are highly crystalline and have a kinetically preferred orientation at (0 1 5) for hexagonal crystal structure. AFM images show uniform morphology with hexagonal-shaped crystals deposited over the entire gold substrate. The structure and composition analyses reveal that the thin films are pure phase with corresponding atomic ratios. The optical studies show that the band gap of (Bi_xSb_1−x)₂Te₃ thin films could be tuned from 0.17 eV to 0.29 eV as a function of composition.     

Open-circuit-potentials of gas/electrode/YSZ boundary versus molten carbonate reference electrode at medium temperatures: II. Potential response of Au, Pt and Ni-cermet electrodes in CH4 + O2 and H2 + O2 gas mixtures

Values of open-circuit-potentials (OCP) have been determined for pairs of electrodes: Au and Pt, Ni-Ce_0.8Sm_0.2O_1.9 cermet and Au, Pt and Sm_0.5Sr_0.5CoO₃ composite at the YSZ electrolyte, in the uniform atmospheres of xCH₄ + yO₂ + (1 − x − y)Ar gas mixtures with variable x and y coefficients, at 600 °C. The determined dependencies of OCP values on the initial gas mixture compositions have been compared with the respective dependencies calculated for equilibrium or quasi-equilibrium compositions of these gas mixtures. The OCP values for the pair of Pt and Au electrodes have been measured also in the xH₂ + yO₂ + (1 − x − y)Ar uniform gas mixtures but no distinct difference of the OCP values has been observed in this atmosphere. For some pairs of electrodes investigated in xCH₄ + yO₂ + (1 − x − y)Ar atmospheres the measured OCP values have shown differences up to ca 0.9-1.0 V. These differences were stable within large range of compositions of this gas mixture. Within this gas composition range one of the electrodes conserves the potential of oxygen electrode determined by oxygen partial pressure in the initial gas mixture and is insensitive to reaction occurring in the gas phase. These results are discussed on the basis of equilibria or some quasi-equilibria, that establish in the C-H-O gas mixture and the solid carbon deposition is considered. For a given pair of dissimilar electrodes, their selective sensibility to the electrochemical process of oxygen electrode has been confirmed. Within large range of gas mixture concentrations, in the Pt-Au electrode pair Au has shown behavior of the oxygen electrode, whereas the OCP values of the Pt electrode are within the range of hydrogen electrode, also at gas compositions corresponding to the solid carbon stability. With this pair the OCP differences of ca. 600 mV have been obtained. Among three electrodes studied the cermet Ni-Ce_0.8Sm_0.2O_1.9 electrode shows the best electrocatalytic properties resulting in the OCP values following exactly the respective equilibrium dependence. In the pair Ni-Ce_0.8Sm_0.2O_1.9 and Au a stable potential difference of ca. 900 mV have been established. Unexpectedly, Pt electrode in the pair with the Sm_0.5Sr_0.5CoO₃ composite electrode plays role of the oxygen electrode quite insensitive to other components of the equilibrated initial gas mixture. This surprising fact seems indicate that in conditions of the experiments performed the electrocatalytic behavior of the electrode depends not only of the material of this electrode but also on the properties of the second electrode in the given pairs of electrodes.     

Transesterification of palm oil on KyMg1 − xZn1 + xO3 catalyst: Effect of Mg-Zn interaction

The Mg-Zn interaction effect of K_yMg_1 − xZn_1 + xO₃ heterogeneous type catalyst and its performance on transesterification of palm oil have been studied using the response surface methodology and the factorial design of experiments. The catalyst was synthesized using the co-precipitation method and the activity was assessed by transesterification of palm oil into fatty acid methyl esters. The ratio of the Mg/Zn metal interaction, temperature and time of calcination were found to have positive influence on the conversion of palm oil to fatty acid methyl ester (FAME) with the effect of metal to metal ratio and temperature of calcination being more significant. The catalytic activity was found to decrease at higher calcination temperature and the catalyst type K₂Mg_0.34Zn_1.66O₃ with Mg/Zn ratio of 4.81 gave FAME content of 73% at a catalyst loading of 1.404 wt.% of oil with molar ratio of methanol to oil being 6:1 at temperature of 150 °C in 6 h. A regression model was obtained to predict conversions to methyl esters as a function of metal interaction ratio, temperature of calcination and time. The observed activity of the synthesized catalyst was due to its synergetic structure and composition.     

Preparation of Ni/MgxTi1 − xO catalysts and investigation on their stability in tri-reforming of methane

Ni/Mg_xTi_1 − xO catalysts were prepared through a wet impregnation method by dispersing Ni on Mg_xTi_1 − xO composite oxides obtained via a sol–gel technique. The Ni/Mg_xTi_1 − xO catalysts were characterized by various means including ICP–OES, BET, XRD, H₂–TPR, SEM, and TG. No free NiO peak was found in all XRD patterns of the Ni/Mg_xTi_1 − xO catalysts. The H₂–TPR and chemisorption results indicated that adding Ti to the NiO–MgO system obstructed the formation of solid solution, and thus increased the reducibility of the catalysts. The prepared Mg_xTi_1 − xO composite oxides had the same ability to disperse Ni as TiO₂ and MgO. The tri-reforming (simultaneous oxygen reforming, carbon dioxide reforming, and steam reforming) of methane over Ni/Mg_xTi_1 − xO catalysts was carried out in a fixed bed flow reactor. The conversions of CH₄ and CO₂ can respectively be achieved as high as above 95% and 83% over Ni/Mg_0.75Ti_0.25O catalyst under the reaction conditions. The activity of Ni/Mg_0.75Ti_0.25O and Ni/Mg_0.5Ti_0.5O did not decrease for a reaction period of 50 h, indicating their rather high stability. The experimental results showed that the nature of support, the interaction between metal and support, and the ability to be reduced played an important role in improving the stability of catalysts.     

Synthesis and characterization of ZnxMg1 − xGa2O4:Co fabricated by low-temperature burning method

A series of Zn_xMg_1 − xGa₂O₄:Co²⁺ spinels (x = 0, 0.25, 0.5, 0.75, and 1.0) was successfully produced through low-temperature burning method by using Mg(NO₃)₂·4H₂O, Zn(NO₃)₂·6H₂O, Ga(NO₃)₃·6H₂O, CO(NH₂)₂, NH₄NO₃, and Co(NO₃)₂·6H₂O as raw materials. The product was characterized by X-ray diffraction, transmission electron microscopy, and photoluminescence spectroscopy. The product was not merely a simple mixture of MgGa₂O₄ and ZnGa₂O₄; rather, it formed a solid solution. The lattice constant of Zn_xMg_1 − xGa₂O₄:Co²⁺ (0 ≤ x ≤ 1.0) crystals has a good linear relationship with the doping density, x. The synthesized products have high crystallinities with neat arrays. Based on an analysis of the form and position of the emission spectrum, the strong emission peak around the visible region (670 nm) can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴A₂(⁴F)] of Co²⁺ in the tetrahedron. The weak emission peak in the near-infrared region can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴T₂(⁴F)] of Co²⁺ in the tetrahedron.     

Insignificant impact of designed oxygen release from high capacity Li[(Ni1/2Mn1/2)xCoy(Li1/3Mn2/3)1/3]O2 (x + y = 2/3) positive electrodes during the cycling of Li-ion cells

The properties of graphite/Li[(Ni_0.5Mn_0.5)_xCo_y(Li_1/3Mn_2/3)_1/3]O₂ (x + y = 2/3, y = 1/12 and 1/6) Li-ion cells are reported. There is an extended plateau near 4.5 V during the first charging of the cells that corresponds to the simultaneous removal of Li and oxygen from the Li[(Ni_0.5Mn_0.5)_xCo_y(Li_1/3Mn_2/3)_1/3]O₂ (x + y = 2/3, y = 1/12 and 1/6) electrodes. The release of this oxygen directly within a Li-ion cell has been a cause for concern. However, it was found that subsequent to O₂ release, Li-ion cells delivered a high reversible positive electrode specific capacity near 250 mAh/g at C/30 between 2.5 and 4.8 V, the cells did not display increased irreversible capacity relative to counterparts having Li metal negative electrodes and the cells retained 85% of their initial capacity after 70 cycles at C/6 between 2.5 and 4.6 V. Therefore, the O₂ released during the first charge does not significantly impact the electrochemical properties of graphite/Li[(Ni_0.5Mn_0.5)_xCo_y(Li_1/3Mn_2/3)_1/3]O₂ (x + y = 2/3) lithium-ion cells.     

Electrochemical properties of La1−xSrxFeO3 (x = 0.2, 0.4) as negative electrode of Ni-MH batteries

La_(1−x)Sr_xFeO₃ (x = 0.2,0.4) powders were prepared by a stearic acid combustion method, and their phase structure and electrochemical properties were investigated systematically. X-ray diffraction (XRD) analysis shows that La_(1−x)Sr_xFeO₃ perovskite-type oxides consist of single-phase orthorhombic structure (x = 0.2) and rhombohedral one (x = 0.4), respectively. The electrochemical test shows that the reaction at La_(1−x)Sr_xFeO₃ oxide electrodes are reversible. The discharge capacities of La_(1−x)Sr_xFeO₃ oxide electrodes increase as the temperature rises. With the increase of the temperature from 298 K to 333 K, their initial discharge capacity mounts up from 324.4 mA h g⁻¹ to 543.0 mA h g⁻¹ (when x = 0.2) and from 147.0 mA h g⁻¹ to 501.5 mA h g⁻¹ (when x = 0.4) at the current density of 31.25 mA g⁻¹, respectively. After 20 charge-discharge cycles, they still remain perovskite-type structure. Being similar to the relationship between the discharge capacity and the temperature, the electrochemical kinetic analysis indicates that the exchange current density and proton diffusion coefficient of La_(1−x)Sr_xFeO₃ oxide electrodes increase with the increase of the temperature. Compared with La_0.8Sr_0.2FeO₃, La_0.6Sr_0.4FeO₃ electrode is a more promising candidate for electrochemical hydrogen storage because of its higher cycle capacity at various temperatures.     

The underpotential deposition of Bi2Te3−ySey thin films by an electrochemical co-deposition method

Bi₂Te_3−ySe_y thin films were grown on Au(1 1 1) substrates using an electrochemical co-deposition method at 25 °C. The appropriate co-deposition potentials based on the underpotential deposition (upd) potentials of Bi, Te and Se have been determined by the cyclic voltammetric studies. The films were grown from an electrolyte of 2.5 mM Bi(NO₃)₃, 2 mM TeO₂, and 0.3 mM SeO₂ in 0.1 M HNO₃ at a potential of −0.02 V vs. Ag|AgCl (3 M NaCl). X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) were employed to characterize the thin films. XRD and EDS results revealed that the films are single phase with approximate composition of Bi₂Te_2.7Se_0.3. SEM studies showed that the films are homogeneous and have micronsized granular crystallites.     

Formic acid electro-oxidation on carbon supported PdxPt1−x (0 ≥ x ≥ 1) nanoparticles synthesized via modified polyol method

Carbon supported nanoparticle catalysts of Pd_xPt_1−x (0 ≥ x ≥ 1) were synthesized using a modified polyol method and poly(N-vinyl-2-pyrrolidone) (PVP) as a stabilizer. Resulting nanoparticles were characterized by X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV) and chronoamperommetry (CA) study for formic acid electro-oxidation. Surface composition of the synthesized nanoparticles found from XPS revealed the Pt surface segregation even for the Pd-rich compositions. It is suggested that the surface segregation behavior in PdPt nanoparticles supported on carbon may be influenced, in addition to the difference in Pd and Pt surface energies, by particle size and particle interaction with the support. According to CA, the carbon supported Pd nanoparticles show the highest initial activity towards formic acid electro-oxidation at the potential of 0.3 V (RHE), due to the promotion of the direct dehydrogenation mechanism. However its stability is quite poor resulting in the fast deactivation of the Pd surface. Addition of Pt considerably improves the steady-state activity of Pd in 12 h CA experiment. CA measurements show that the most active catalyst is Pd_0.5Pt_0.5 of 4 nm size, which displays narrow size distribution and Pd to Pt surface atomic ratio of 27-73.     

Amorphous LiCoO2 thin films on Li1+x+yAlxTi2−xSiyP3−yO12 prepared by radio frequency magnetron sputtering for all-solid-state Li-ion batteries

Amorphous LiCoO₂ thin films were deposited on the NASICON-type glass ceramics, Li_1+x+yAl_xTi_2−xSi_yP_3−yO₁₂ (LATSP), by radio frequency (RF) magnetron sputtering below 180 °C. The as-deposited LiCoO₂ thin films were characterized by X-ray diffraction, scanning electron microscopy and atomic force microscope. All-solid-state Li/PEO₁₈-Li (CF₃SO₂)₂N/LATSP/LiCoO₂/Au cells were fabricated using the amorphous film. The electrochemical performance of the cells was investigated by galvanostatic cycling, cyclic voltammetry, potentiostatic intermittent titration technique and electrochemical impedance spectroscopy. It was found that the amorphous LiCoO₂ thin film shows a promising electrochemical performance, making it a potential application in microbatteries for microelectronic devices.     

Preparation, characterization and electrical conductivity studies of NdYb1−xGdxZr2O7 (0 ≤ x ≤ 1.0) ceramics

Several compositions of NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 1.0) ceramics were prepared by pressureless-sintering method at 1973 K for 10 h in air. The relative density, microstructure and electrical conductivity of NdYb_1−xGd_xZr₂O₇ ceramics were analyzed by the Archimedes method, X-ray diffraction, scanning electron microscopy and impedance plots measurements. NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 0.3) ceramics have a single phase of defect fluorite-type structure, and NdYb_1−xGd_xZr₂O₇ (0.7 ≤ x ≤ 1.0) ceramics exhibit a single phase of pyrochlore-type structure; however, the NdYb_0.5Gd_0.5Zr₂O₇ composition shows mixed phases of both defect fluorite-type and pyrochlore-type structures. The measured values of the grain conductivity obey the Arrhenius relation. The grain conductivity of each composition in NdYb_1−xGd_xZr₂O₇ ceramics gradually increases with increasing temperature from 673 to 1173 K. NdYb_1−xGd_xZr₂O₇ ceramics are oxide-ion conductor in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest grain conductivity value obtained in this work is 1.79 × 10⁻² S cm⁻¹ at 1173 K for NdYb_0.3Gd_0.7Zr₂O₇ composition.     

Perovskite-type La2−xSrxNiO4 (0 ≤ x ≤ 1) as active anode materials for methanol oxidation in alkaline solutions

Perovskite-type ternary oxides with molecular formulae, La_2−xSr_xNiO₄ (0 ≤ x ≤ 1), were prepared by a modified citric acid sol-gel route at 600 °C for their possible use in a direct methanol fuel cell (DMFC). The study was conducted by cyclic voltammetry, chronoamperometry, impedance and anodic Tafel polarization techniques. The results showed that the electrocatalytic activity of the base oxide (x = 0) in 1 M KOH plus 1 M CH₃OH at 25 °C increases with x, the observed current densities being 23.6, 47.3, 43.2 and 50.9 mA cm⁻² at a scan rate of 10 mV s⁻¹ and E = 0.6 V versus Hg/HgO for oxides with x = 0, 0.25, 0.5 and 1.0, respectively. All the four perovskite anodes used in this study did not indicate any poisoning by the methanol oxidation intermediates/products. The methanol electro-oxidation reaction followed a Tafel slope of ∼2 × 2.303RT/3F (=40 mV decade⁻¹) on each oxide catalyst, regardless of Sr content.     

Properties of Ni1−xFex (0.1 < x < 0.9) and Invar (x = 0.64) alloys obtained by electrodeposition

Electrodeposition of Ni_1−xFe_x (x = 0.1-0.9) films was carried out from a chloride plating solution containing saccharin as an organic additive at a constant current density (5 mA/cm²) and a controlled pH of 2.5. X-ray diffraction studies revealed the existence of an fcc, or γ phase, in the range of 10-58 wt.% Fe, a mixed fcc/bcc phase in the range of 59-60 wt.% Fe, and a bcc, or α phase in the range of 64-90 wt.% Fe. The saturation magnetization, B_s, of electrodeposited Ni_1−xFe_x alloys at the room temperature was found to increase with the increase of Fe-content and follows the Slater-Pauling curve, but deviates from as-cast bulk NiFe alloys. The coefficient of thermal expansion, CTE, of electrodeposited alloys at room temperature also deviates from as-cast bulk NiFe alloys. Annealing of α-Ni₃₆Fe₆₄ alloy results in a martensitic α → γ phase transformation, which takes place between 300 and 400 °C. It was demonstrated that thermal treatment above 400 °C was necessary to obtain magnetic and mechanical properties similar to those to conventional Invar alloy. Annealing of α-Ni₃₆Fe₆₄ alloy at 700 °C brings about a decrease of B_s from 1.75 to 0.45 T. By controlling the annealing conditions of α → γ martensitic transformation, it is possible to adjust the CTE of Ni₃₆Fe₆₄ alloy over the broad limits from 2.7 to 8.7 × 10⁻⁶/°C.     

Co-doped ceria-based solid solution in the CeO2-M2O3-CaO, M = Sm, Gd system

The Pechinni method (A) as well as hydrothermal treatment (B) of co-precipitated CeO₂-based gels with NaOH solution were used to synthesise pure CeO₂, and CeO₂-based solid solutions with formula Ce_1−xM_xO₂, Ce_1−x(M_0.5Ca_0.5)_xO₂ M = Gd, Sm for 0.15 < x < 0.3 nanopowders. The thermal evolution of CeO₂-based precursors during heating them up to 1000 °C was monitored by thermal (TG, DTA) analysis and X-ray diffraction method. All nanopowders and samples sintered were found to be pure CeO₂ or ceria-based solutions with fluorite-type structure. The microstructure of CeO₂-based sintered samples at 1500 °C (A) or 1250 °C (B) was observed for 2 h under the scanning electron microscope. The electrical properties of singly Ce_1−xM_xO₂ or doubly doped CeO₂-based samples with formula Ce_1−x(M_0.5Ca_0.5)_xO₂, M = Gd, Sm, 0.15 < x < 0.30 were investigated by means of the ac impedance spectroscopy method throughout the temperature range of 600-800 °C. It has been stated that partial substitution of calcium by samarium or calcium by gadolinium in the Ce_1−x(M_0.5Ca_0.5)_xO₂, M = Gd, Sm solid solutions leads to ionic conductivity enhancement comparable with only samaria- or gadolina-doped ceria. The CeO₂-based samples with small-grained microstructures obtained from powders synthesised by hydrothermal method exhibited better ionic conductivity than samples with the same composition obtained from powders synthesised by the Pechinii method. The stability of the electrolytic properties of selected co-doped ceria sinters in fuel gases (H₂, CH₄) as well as exhaust gases from diesel engine was also investigated. The co-doped Ce_0.8(Sm_0.5Ca_0.5)_0.2O₂ or Ce_0.85(Gd_0.5Ca_0.5)_0.15O₂ dense samples would appear be to more adequate oxide electrolytes than Ce_1−xM_xO₂, M = Sm, Gd and x = 0.15 or 0.2 for electrochemical devices operating at temperatures ranging from 600 to 700 °C.     

Polypyrrole and La1−xSrxMnO3 (0≤ x ≤0.4) composite electrodes for electroreduction of oxygen in alkaline medium

Composite G/PPy/PPy(La_1−xSr_xMnO₃)/PPy electrodes made of the perovskite La_1−xSr_xMnO₃ embedded into a polypyrrole (PPy) layer, sandwiched between two pure PPy films, electrodeposited on a graphite support were investigated for electrocatalysis of the oxygen reduction reaction (ORR). PPy and PPy(La_1−xSr_xMnO₃) (0≤ x ≤0.4) successive layers have been obtained on polished and pretreated graphite electrodes following sequential electrodeposition technique. The electrolytes used in the electrodeposition process were Ar saturated 0.1 mol dm⁻³ pyrrole (Py) plus 0.05 mol dm⁻³ K₂SO₄ with and without containing a suspension of 8.33 g L⁻¹ oxide powder. Films were characterized by XRD, SEM, linear sweep voltammetry, cyclic voltammetry (CV) and electrochemical impedance (EI) spectroscopy. Electrochemical investigations were carried out at pH 12 in a 0.5 mol dm⁻³ K₂SO₄ plus 5 mmol dm⁻³ KOH, under both oxygenated and deoxygenated conditions. Results indicate that the porosity of the PPy matrix is considerably enhanced in presence of oxide particles. Sr substitution is found to have little influence on the electrocatalytic activity of the composite electrode towards the ORR. However, the rate of oxygen reduction decreases with decreasing pH of the electrolyte from pH 12 to pH 6. It is noteworthy that in contrast to a non-composite electrode of the same oxide in film form, the composite electrode exhibits much better electrocatalytic activity for the ORR.     

Improvement of electrochemical properties of Li[Ni0.4Co0.2Mn(0.4−x)Mgx]O2−yFy cathode materials at high voltage region

Spherical Li[Ni_0.4Co_0.2Mn_(0.4−x)Mg_x]O_2−yF_y (x = 0, 0.04, y = 0, 0.08) with phase-pure and well-ordered layered structure have been synthesized by heat-treatment of spherical [Ni_0.4Co_0.2Mn_0.4−xMg_x]₃O₄ precursors with LiOH·H₂O and LiF salts. The average particle size of the powders was about 10-15 μm and the size distribution was quite narrow due to the homogeneity of the metal carbonate, [Ni_0.4Co_0.2Mn_(0.4−x)Mg_x]CO₃ (x = 0, 0.04) precursors. Although the Li[Ni_0.4Co_0.2Mn_0.36Mg_0.04]O_1.92F_0.08 delivered somewhat slightly lower initial discharge capacity, however, the capacity retention, interfacial resistance, and thermal stability were greatly enhanced comparing to the Li[Ni_0.4Co_0.2Mn_0.4]O₂ and Li[Ni_0.4Co_0.2Mn_0.36Mg_0.04]O₂.     

Oxygen and chlorine evolution on RuO2 + TiO2 + CeO2 + Nb2O5 mixed oxide electrodes

A systematic investigation was conducted on the mechanism and electrocatalytic properties of O₂ and Cl₂ evolution on mixed oxide electrodes of nominal composition: Ti/[Ru_(0.3)Ti_(0.6)Ce_(0.1−x)]O₂[Nb₂O₅]_(x) (0 ≤ x ≤ 0.1). For the oxygen evolution, a 30 mV Tafel slope is obtained in the presence of CeO₂, while in its absence a 40 mV coefficient is observed. The intrinsic electrocatalytic activity is mainly due to electronic factors, as result of the synergism between Ru and Ce oxides. For chlorine evolution, the Tafel slope (30 mV) is independent on oxide composition. The best global electrocatalytic activity for ClER was observed in the absence of Nb₂O₅ additive. Variation of the voltammetric charge throughout the experiments confirms high CeO₂ content compositions are fragile, due mainly to the porosity caused by CeO₂ presence. On the other hand, Nb₂O₅ addition decreases considerably this instability.