激光熔覆原位合成陶瓷相增强铁基熔覆层的组织和性能

利用6 kW光纤激光器在Cr12MoV汽车模具钢表面激光熔覆含有Ti-Fe,B₄C粉末的铁基合金粉,在汽车模具钢表面直接原位合成TiC+TiB₂颗粒增强的铁基合金复合涂层.涂层与基体呈良好的冶金结合,涂层组织细小,结构致密,宏观质量较好. XRD分析结果表明,涂层组织由α-Fe,TiC,TiB₂组成. TiC,TiB₂相均匀分布于熔覆层中.由于TiC,TiB₂硬质相的形成以及激光的快速凝固冷却获得的细晶组织,使得熔覆层的显微维氏硬度有了明显提高.在距离熔覆层表面1.2 mm处显微维氏硬度高达1000 HV,有利于促进熔覆层耐磨性的提高.     

电弧熔炼Ti6Al4V/B4C复合材料微观组织与力学性能

采用真空电弧熔炼技术制备了不同含量B₄C的Ti6Al4V/B₄C钛基复合材料,并采用光学显微镜、扫描电子显微镜、显微硬度计、静态压缩及拉伸测试等对其微观组织及力学性能进行了表征分析. 结果表明,电弧熔炼过程B₄C与钛基体原位反应生成TiB,TiC及TiB₂相,TiB呈现一维生长晶须状,TiC呈现颗粒状,在B₄C质量分数为10%时生成块状TiB₂,并可能会形成特殊的中空棱柱状结构Ti(B_xC_y)聚合物. 原位反应生成的TiB₂可显著提高钛基复合材料的显微硬度. 当B₄C质量分数为0.5%时,钛基复合材料原位反应生成的连续网状、均匀分布的TiB和TiC试样具有最优力学性能,试样最大抗压强度值达到1 990 MPa,最大压缩应变为35.5%,压缩性能超过熔炼钛合金,抗拉强度达到1 034 MPa,与熔炼钛合金材料相比提高近24%,但塑性有所降低,并随着B₄C含量增加,抗拉强度逐渐下降,其断裂方式由韧性断裂转变为脆性断裂.     

TIG熔覆原位自生TiC-TiB2/Fe复合涂层

利用氩弧作为热源,以G302铁基合金粉、FeTi70粉和B₄C粉作为原料粉末,在Q235表面原位生成TiC-TiB₂增强的铁基复合涂层. 采用一系列的分析测试方法对涂层进行了表征,结果表明,氩弧熔覆过程冶金反应充分,熔覆层中生成了TiC,TiB₂和M₇C₃等硬质增强相;熔覆层组织呈现出由母材界面到熔覆层表面硬质相逐渐增多的梯度分布特征. 增加FeTi70和B₄C粉末比例提高了熔覆层硬度,质量比为G302:FeTi70:B₄C=6:3:1时,试样最大硬度达到976 HV0.1,是母材硬度的5倍左右. 在与GCr15钢对磨时,熔覆试样磨损量仅为Q235钢的1/30左右,熔覆层磨损表面基本无塑性变形痕迹,涂层中坚硬的TiC,TiB₂陶瓷相起到阻磨作用.     

Ti6Al4V合金表面氩弧熔覆原位合成TiC-TiB2增强钛基复合涂层组织与耐磨性

以B4C和Ni60A粉末为预涂材料,采用氩弧熔覆技术,在Ti6Al4V合金表面原位合成TiC与TiB₂增强相增强钛基复合材料涂层.运用XRD,SEM等分析手段研究了复合涂层的显微组织,利用显微硬度仪测试了复合涂层的显微硬度并用磨损试验机分析了其在室温干滑动磨损条件下的耐磨性能.结果表明,熔覆层组织主要由TiC和TiB₂组成,TiC颗粒和TiB₂颗粒弥散分布在基体上,TiC颗粒的尺寸为2~3μm,而呈长条状的TiB₂颗粒尺寸为3~5μm.显微硬度和耐磨性测试结果表明,该复合涂层显微维氏硬度高达1200MPa左右,复合涂层的耐磨性能比Ti6Al4V基体提高约20倍.     

基于Ti中间层的B4C复合陶瓷扩散连接接头界面微观组织与力学性能

碳化硼(B₄C)复合陶瓷以其高硬度、高熔点、良好的耐磨性以及吸收中子能力的特性,广泛应用于制造防弹装甲材料,原子反应堆控制以及耐磨耐高温结构材料等领域.文中采用中间层Ti箔对碳化硼复合陶瓷(B₄C-SiC-TiB₂)进行扩散连接,研究了连接温度对连接界面组织及接头力学性能的影响.结果表明,在连接温度1300 ~ 1450 ℃下成功扩散连接了B₄C-SiC-TiB₂复合陶瓷,Ti与B₄C反应生成TiB₂和TiC.随着连接温度的升高,反应层变厚,而过厚的反应层会对接头的性能造成不利影响.在连接温度1300 ℃时,反应层的平均厚度约为5 μm,此时获得较高的接头抗剪强度100 MPa;在连接温度1450 ℃时连接层基本为TiB₂和TiC陶瓷相,此时扩散连接接头可以获得较高硬度(25.4 GPa).     

TC4钛合金表面激光熔覆复合涂层的组织和耐磨性

采用5 kW横流CO₂激光器,在TC4钛合金表面熔覆TiC、TiB₂与Ni的混合粉末,制备了无气孔、无裂纹、组织均匀致密的复合涂层。用SEM、EDS、XRD、显微硬度计以及立式万能摩擦磨损试验机分析了激光熔覆层的显微组织、成分和物相,测试了激光熔覆层横截面显微硬度,以及覆层耐磨性能。结果表明,激光熔覆复合涂层与基体呈冶金结合;熔覆层组织从表层到结合区呈现出由棒状、块状向树枝状、颗粒状转变的趋势,且主要由Ti、TiC、TiB、Ti₂Ni、TiNi等相组成;熔覆层显微硬度最高可达863 HV0.2,为基体的2.5倍;熔覆层耐磨性能较TC4钛合金明显提高。     

纯铜表面氩弧熔覆TiB2/Ni复合涂层组织及耐磨性能

通过氩弧熔覆技术在纯铜表面制备TiB₂增强 Ni 基复合涂层,以改善其耐磨性能. 将钛粉、硼粉和镍粉在球磨机中充分混合,采用氩弧熔覆技术将纯铜表面预置粉末熔化制备出陶瓷颗粒增强镍基熔覆层. 采用X射线衍射仪、扫描电子显微镜、透射电子显微镜分析涂层的物相及涂层中陶瓷颗粒相的组成、分布及结构,利用显微硬度仪和摩擦磨损试验机测试涂层的显微硬度和耐磨性能. 结果表明,熔覆层物相主要包括γ(Ni, Cu)和TiB₂;陶瓷颗粒增强相弥散分布于熔覆层中,其中颗粒相TiB₂以六边形存在,熔覆层内部与基体界面处均无缺陷产生;熔覆涂层具有较高的显微硬度,当(Ti+B)质量分数为10%时,涂层显微硬度高达781.3 HV,与纯铜基体对比,熔覆层显微硬度提高约11.7倍;在相同磨损条件下,随(Ti+B)质量分数的增加,熔覆涂层的摩擦系数及磨损失重先减小后增大;氩弧熔覆原位自生TiB₂陶瓷颗粒增强镍基熔覆层可显著提高纯铜表面的耐磨性能.     

激光熔化沉积TiB2增强TiAl基合金涂层的组织及力学性能

采用激光熔化沉积在TC4合金表面制备出不同TiB₂含量(0、10%、20%、30%，质量分数)的TiAl基合金涂层，利用XRD、OM、SEM、显微硬度计、压痕法(断裂韧性)、磨损试验机以及激光共聚焦显微镜等，系统研究了TiB₂含量对涂层微观组织与力学性能的影响。结果表明，涂层组织由底部沿厚度方向依次为平面晶、柱状晶和等轴晶，随着TiB₂含量增加，柱状晶高度逐渐降低。TiB₂/TiAl复合涂层由Ti Al合金基体相(γ+α2)以及TiB₂增强相组成，直接添加的TiB₂颗粒大多没有熔化，但直接添加的TiB₂颗粒外层与Ti Al合金熔体发生溶解反应后原位析出初生TiB₂和次生TiB₂，初生TiB₂呈块状，次生TiB₂呈短棒状和条带状。随着TiB₂含量由0增加至10%，涂层基体组织明显细化，但继续增加TiB₂含量...     

TA2合金激光熔 α-Ti/TiC+(Ti,W)C1-x/Ti2SC+TiS自润滑耐磨复合涂层

目的提高TA2钛合金的耐磨减摩性能,并研究添加WS_2对激光熔覆Ti/TiC耐磨复合涂层的影响。方法以Ti+TiC和Ti+TiC+WS_2两种复合粉末为预置原料,采用激光熔覆技术在TA2合金表面制备出两类复合涂层,并采用X射线衍射仪(XRD)、扫描电镜(SEM)、能谱仪(EDS)、硬度计和摩擦磨损试验机,系统地分析了添加WS_2前后涂层的物相、组织、显微硬度及摩擦学性能。结果 Ti+TiC复合粉末的激光熔覆涂层的主要物相包含α-Ti和TiC,涂层的显微硬度为1162HV0.5。WS_2添加后,涂层中生成了新增强相(Ti,W)C_(1-x)及自润滑相Ti2SC和少量的TiS,涂层的显微硬度为1052.3HV0.5,约为TA2基体(180HV0.5)的5倍;此外,涂层的磨损率由未添加WS_2时的5.38×10~(-5) mm~3/(N·m)上升到15.98×10-5 mm~3/(N·m),耐磨性能有所下降但仍远低于基体(磨损率为66.63×10~(-5)mm~3/(N·m)),同时摩擦系数显著下降,由之前的0.49下降到0.34;同时,Si_3N_4对磨球磨损表面光滑,没有明显塑性变形,其磨损机理为轻微的塑性变形和粘着磨损。结论添加WS_2的复合涂层相对于基体依然具有良好的耐磨性能,同时由于新生的自润滑相Ti_2SC、TiS的润滑效果,涂层表现出良好的自润滑耐磨性能。     

Ti-6Al-4V合金表面激光熔覆TiAlSi+xB4C涂层的组织及耐磨性

利用激光熔覆在Ti-6Al-4V合金表面制备了TiAlSi+xB₄C涂层,分析比较不同B₄C含量对于涂层显微组织、显微硬度和耐磨性能的影响。结果表明:B₄C含量不同,涂层中的物相种类差别不大;涂层的微观形貌由颗粒状晶、层状晶、胞状晶和短棒状晶组成;不同B₄C含量涂层的显微硬度分布趋势大致相同,与基材相比均有明显的提高,随着B₄C含量的增高,整体上涂层显微硬度逐渐增大,当B₄C的含量为8%时,涂层的显微硬度最高,达到1216 HV0.1,约为基体的4.2倍;而当B₄C含量过高时,涂层硬度降低,且涂层中出现微裂纹。通过磨损试验表明,不同B₄C含量的涂层耐磨损性能均明显的优于Ti-6Al-4V合金基体,含8%B₄C的涂层磨损量最小。熔覆不同含量B₄C的涂层明显改善了基体Ti-6Al-4V合金的表面性能。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

THERMODYNAMICS STUDY ON THE DECOMPOSITION OF CHROMITE WITH KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

INFLUENCE OF HEAT TREATMENT ON DAMPING BEHAVIOUR OF THE MAGNESIUM WROUGHT ALLOY AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Theoretical Analysis for the Motion and Temperature of Melt Droplets in Spray Degassing Process

The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results.     

Growth Kinetics of Single Inclusion Particle in Molten Melts

On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes＇ collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process.     

An Easy Way to Quantify the Adhesion Energy of Nanostructured Cu/X(X=Cr,Ta,Mo,Nb,Zr) Multilayer Films Adherent to Polyimide Substrates

An approach based on film buckling under simple uniaxial tensile testing was utilized in this paper to quantitatively estimate the interfacial energy of the nanostructured multilayer films(NMFs) adherent to flexible substrates. The interfacial energies of polyimide-supported NMFs are determined to be *5.0 J/m2 for Cu/Cr, *4.1 J/m2 for Cu/Ta,*2.8 J/m2 for Cu/Mo, *1.1 J/m2 for Cu/Nb, and *1.2 J/m2 for Cu/Zr NMFs. Furthermore, a linear relationship between the adhesion energy and the interfacial shear strength is clearly demonstrated for the Cu-based NMFs, which is highly indicative of the applicability and reliability of the modified models.     

High-Speed Friction Stir Welding of SiC_p/Al–Mg–Si–Cu Composite

A 17 vol% SiCp/Al–Mg–Si–Cu composite plate with a thickness of 3 mm was successfully friction stir welded(FSWed) at a very high welding speed of 2000 mm/min for the first time. Microstructural observation indicated that the coarsening of the precipitates was greatly inhibited in the heat-affected zone of the FSW joint at high welding speed, due to the significantly reduced peak temperature and duration at high temperature. Therefore, prominent enhancement of the hardness was achieved at the lowest hardness zone of the FSW joint at this high welding speed, which was similar to that of the nugget zone. Furthermore, the ultimate tensile strength of the joint was as high as 369 MPa, which was much higher than that obtained at low welding speed of 100 mm/min(298 MPa). This study provides an effective method to weld aluminum matrix composite with superior quality and high welding efficiency.     

A STUDY OF TEMPERATURE-DEPENDENT VALENCE BOND STRUCTURE OF TITANIUM

On the basis of energy and shape method for the determination of the valence bond (VB) structures of crystal, the valence bond structure of titanium is redetermined at room temperature and calculated in the whole temperature range of 0-1943K. The outer shell electronic distribution of Ti is e_c~(2.9907) · (s_c~(0.4980) d_c~(2.4927)) ef1.0093 in crystal. The temperature dependences of the VB structures of hcp and bcc phases are the same. The VB structures of hcp and bcc phases monotonically increase or decrease with the increase in temperature, but show discontinuous changes at the phase-transformation temperature 1155K.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。