Microstructure and Thermomechanical Properties of Atmospheric Plasma-Sprayed Yb<Subscript>2</Subscript>O<Subscript>3</Subscript> Coating

In this study, a Yb₂O₃ coating was fabricated by the atmospheric plasma spray technique. The phase composition, microstructure, and thermal stability of the coating were examined. The thermal conductivity and thermal expansion behavior were also investigated. Some of the mechanical properties (elastic modulus, hardness, fracture toughness, and flexural strength) were characterized. The results reveal that the Yb₂O₃ coating is predominantly composed of the cubic Yb₂O₃ phase, and it has a dense lamellar microstructure containing defects. No mass change and exothermic phenomena are observed in the thermogravimetry and differential thermal analysis curves. The high-temperature x-ray diffraction results indicate that no phase transformation occurs from room temperature to 1500 °C, revealing the good phase stability of the Yb₂O₃ coating. The coefficient of thermal expansion of the Yb₂O₃ coating is (7.50-8.67)?×?10^?6 K^?1 in the range of 200-1400 °C. The thermal conductivity is about 1.5 W m^?1 K^?1 at 1200 °C. The Yb₂O₃ coating has excellent mechanical properties and good damage tolerant. The unique combination of these properties implies that the Yb₂O₃ coating might be a promising candidate for T/EBCs applications.     

Yb<Subscript>2</Subscript>Si<Subscript>2</Subscript>O<Subscript>7</Subscript> Environmental Barrier Coatings Deposited by Various Thermal Spray Techniques: A Preliminary Comparative Study

Dense, crack-free, uniform, and well-adhered environmental barrier coatings (EBCs) are required to enhance the environmental durability of silicon (Si)-based ceramic matrix composites in high pressure, high gas velocity combustion atmospheres. This paper represents an assessment of different thermal spray techniques for the deposition of Yb₂Si₂O₇ EBCs. The Yb₂Si₂O₇ coatings were deposited by means of atmospheric plasma spraying (APS), high-velocity oxygen fuel spraying (HVOF), suspension plasma spraying (SPS), and very low-pressure plasma spraying (VLPPS) techniques. The initial feedstock, as well as the deposited coatings, were characterized and compared in terms of their phase composition. The as-sprayed amorphous content, microstructure, and porosity of the coatings were further analyzed. Based on this preliminary investigation, the HVOF process stood out from the other techniques as it enabled the production of vertical crack-free coatings with higher crystallinity in comparison with the APS and SPS techniques in atmospheric conditions. Nevertheless, VLPPS was found to be the preferred process for the deposition of Yb₂Si₂O₇ coatings with desired characteristics in a controlled-atmosphere chamber.     

Effect of Microstructure on the Thermal Conductivity of Plasma-Sprayed Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-YSZ Coatings

The microstructures of three atmospheric plasma-sprayed (APS) Al₂O₃-ZrO₂ coatings were investigated using x-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The differences in the microstructures of the three Al₂O₃-ZrO₂ coatings, including their phase compositions, cracks, pores, grain sizes, and solid solutions, were analyzed in detail. A close relationship was observed between the thermal conductivities of the coatings and the microstructures, and the Al₂O₃-YSZ coatings with more spherical pores, fewer vertical cracks, and finer grains exhibited the lowest thermal conductivity of 0.91 W/m·K. Compared with YSZ coatings, Al₂O₃-YSZ coatings can exhibit lower thermal conductivity, which may be attributed to the formation of an amorphous phase, smaller grains, and Al₂O₃-YSZ solid solution.     

Fabrication and Properties of Plasma-Sprayed Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/ZrO<Subscript>2</Subscript> Composite Coatings

Al₂O₃ /xZrO₂ (where x = 0, 3, 13, and 20 wt.%) composite coatings were deposited onto mild steel substrates by atmospheric plasma spraying of mixed α-Al₂O₃ and nano-sized monoclinic-ZrO₂ powders. Microstructural investigation showed that the coatings comprised well-separated Al₂O₃ and ZrO₂ lamellae, pores, and partially molten particles. The coating comprised mainly of metastable γ-Al₂O₃ and tetragonal-ZrO₂ with trace of original α-Al₂O₃ and monoclinic-ZrO₂ phases. The effect of ZrO₂ addition on the properties of coatings were investigated in terms of microhardness, fracture toughness, and wear behavior. It was found that ZrO₂ improved the fracture toughness, reduced friction coefficient, and wear rate of the coatings.     

Dual-Layer Oxidation-Protective Plasma-Sprayed SiC-ZrB<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Carbon Nanotube Coating on Graphite

Graphite is used in high-temperature gas-cooled reactors because of its outstanding irradiation performance and corrosion resistance. To restrict its high-temperature (>873 K) oxidation, atmospheric-plasma-sprayed SiC-ZrB₂-Al₂O₃-carbon nanotube (CNT) dual-layer coating was deposited on graphite substrate in this work. The effect of each layer was isolated by processing each component of the coating via spark plasma sintering followed by isothermal kinetic studies. Based on isothermal analysis and the presence of high residual thermal stress in the oxide scale, degradation appeared to be more severe in composites reinforced with CNTs. To avoid the complexity of analysis of composites, the high-temperature activation energy for oxidation was calculated for the single-phase materials only, yielding values of 11.8, 20.5, 43.5, and 4.5 kJ/mol for graphite, SiC, ZrB₂, and CNT, respectively, with increased thermal stability for ZrB₂ and SiC. These results were then used to evaluate the oxidation rate for the composites analytically. This study has broad implications for wider use of dual-layer (SiC-ZrB₂/Al₂O₃) coatings for protecting graphite crucibles even at temperatures above 1073 K.     

Processing Parameter Effects and Thermal Properties of Y<Subscript>2</Subscript>Si<Subscript>2</Subscript>O<Subscript>7</Subscript> Nanostructured Environmental Barrier Coatings Synthesized by Solution Precursor Induction Plasma Spraying

The solution precursor plasma spray process, in which a solution of metal salts is axially injected into an induction thermal plasma, is suitable for deposition of nanostructured environmental barrier coatings. The effects of main processing parameters, namely the solution precursor concentration, spraying distance, reactor pressure, and atomization gas flow rate, have been analyzed using D-optimal design of experiments regarding the deposition rate and coating porosity responses. Among these four parameters, the solution precursor concentration had the greatest influent on the coating structure, followed by the spraying distance and reactor pressure, and finally the atomization gas flow rate with a small contribution. It is pointed out that the species that impact on the substrate are agglomerates of nanoparticles. The equivalent thermal conductivity of selected coatings was computed from experimental temperature evolution curves obtained by laser flash thermal diffusivity analysis, using two methods: a multilayer finite-element model with optimization, and a multilayer thermal diffusion model. The results of the two models agree, with coatings exhibiting low thermal conductivity between 0.7 and 1 W/(m K) at 800 °C.     

Mechanical Properties of LaTi<Subscript>2</Subscript>Al<Subscript>9</Subscript>O<Subscript>19</Subscript> and Thermal Cycling Behaviors of Plasma-Sprayed LaTi<Subscript>2</Subscript>Al<Subscript>9</Subscript>O<Subscript>19</Subscript>/YSZ Thermal Barrier Coatings

Recently, extensive efforts have been made to develop new thermal barrier coating (TBC) materials which can operate at temperatures above 1523 K over a long term. In this article, LaTi₂Al₉O₁₉ (LTA) was synthesized by solid-state reaction at 1773 K, and the mechanical properties of the LTA bulk were evaluated. The microhardness is about 14 GPa, comparable to that of YSZ bulk, whereas the Young’s modulus is about 44 GPa, lower than the value of YSZ. However, the fracture toughness of 0.8-1 MPa m^1/2 is much lower than that of bulk YSZ. A double-ceramic-layer LTA/YSZ TBC structure was proposed and the TBC sprayed by plasma spraying. Thermal cycling tests of the TBC specimens were performed at 1373 K with a dwell time of 10 min. The LTA remained good stability with ZrO₂ and Al₂O₃. However, the single layer LTA TBC was cracked at the LTA/bond coat interface after about 300 cycles, due to its poor thermal shock resistance, while the YSZ TBC yielded a lifetime of about 1000 cycles. The LTA/YSZ TBC remained intact even after 3000 cycles, exhibiting a promising potential as new TBC materials.     

Mechanical Properties of Layered La<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript> Thermal Barrier Coatings

Lanthanum zirconate (La₂Zr₂O₇) has been proposed as a promising thermal barrier coating (TBC) material due to its low thermal conductivity and high stability at high temperatures. In this work, both single and double-ceramic-layer (DCL) TBC systems of La₂Zr₂O₇ and 8 wt.% yttria-stabilized zirconia (8YSZ) were prepared using air plasma spray (APS) technique. The thermomechanical properties and microstructure were investigated. Thermal gradient mechanical fatigue (TGMF) tests were applied to investigate the thermal cycling performance. The results showed that DCL La₂Zr₂O₇ + 8YSZ TBC samples lasted fewer cycles compared with single-layered 8YSZ TBC samples in TGMF tests. This is because DCL La₂Zr₂O₇ TBC samples had higher residual stress during the thermal cycling process, and their fracture toughness was lower than that of 8YSZ. Bond strength test results showed that 8YSZ TBC samples had higher bond strength compared with La₂Zr₂O₇. The erosion rate of La₂Zr₂O₇ TBC samples was higher than that of 8YSZ samples, due to the lower critical erodent velocity and fracture toughness of La₂Zr₂O₇. DCL porous 8YSZ + La₂Zr₂O₇ had a lower erosion rate than other SCL and DCL La₂Zr₂O₇ coatings, suggesting that porous 8YSZ serves as a stress-relief buffer layer.     

Relationship Between the Microstructure and Thermal Conductivity of Plasma-Sprayed ZrO<Subscript>2</Subscript> Coatings

Plasma-sprayed yttria-stabilized zirconia coatings have a complex microstructure consisting of a variety of pores and cracks. These microstructure features which are determined by the spray process are known to influence the thermal conductivity of coatings. In this article, the microstructure features such as total porosity, large pores, and small pores were quantified by means of scanning electron microscopy (SEM) and image analysis, and for each spray process, the particle velocity and particle temperature were measured prior to impact onto the substrate using the online monitoring system (Spray Watch 2i). Multiple linear regression was used to find the relationship between the particle state and the spray gun parameters. The linear regression models were also investigated between the particle state and the microstructure features, in addition, between the microstructure features and the thermal conductivity. The comprehensive correlation of spray process-microstructure-thermal conductivity was established for plasma-sprayed ZrO₂ coatings.     

Thermal Spray Deposition,Phase Stability and Mechanical Properties of La<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript>/LaAlO<Subscript>3</Subscript> Coatings

This paper deals with the deposition of La₂Zr₂O₇ (LZO) and LaAlO₃ (LAO) mixtures by air plasma spray (APS). The raw material for thermal spray, single phase LZO and LAO in a 70:30 mol.% ratio mixture was prepared from commercial metallic oxides by high-energy ball milling (HEBM) and high-temperature solid-state reaction. The HEBM synthesis route, followed by a spray-drying process, successfully produced spherical agglomerates with adequate size distribution and powder-flow properties for feeding an APS system. The as-sprayed coating consisted mainly of a crystalline LZO matrix and partially crystalline LAO, which resulted from the high cooling rate experienced by the molten particles as they impact the substrate. The coatings were annealed at 1100 °C to promote recrystallization of the LAO phase. The reduced elastic modulus and hardness, measured by nanoindentation, increased from 124.1 to 174.7 GPa and from 11.3 to 14.4 GPa, respectively, after the annealing treatment. These values are higher than those reported for YSZ coatings; however, the fracture toughness (K _IC) of the annealed coating was only 1.04 MPa m^0.5.     

Microstructure and Optical Properties of SS/Mo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Spectrally Selective Solar Absorber Coating

Surface-textured Mo thin film is fabricated by magnetron sputtering through the adjustment of deposition parameters, which exhibits a high absorptance of 0.80 and a low emittance of 0.09. The single-layer Mo deposited on stainless steel (SS) is characterized by x-ray diffraction (XRD), ultra-high resolution scanning electron microscope, atomic force microscope and optical measurement. The controlled surface roughness combined with larger aspect ratio contributes much to the high absorptance and low emittance. Based on the SS/Mo coating, a spectrally selective coating (SS/Mo/Al₂O₃) is designed and fabricated. The coating shows an amorphous structure and exhibits an absorptance of 0.90 and an emittance of 0.08. Tauc-Lorentz and Drude free-electron models are used to modeling the optical properties of Al₂O₃ and Mo layers by phase-modulated spectroscopic ellipsometry.     

Effects of hBN Content on the Microstructure and Properties of Atmospheric Plasma-Sprayed NiCr/Cr<Subscript>3</Subscript>C<Subscript>2</Subscript>-hBN Composite Coatings

NiCr/Cr₃C₂-hBN composite coatings with different contents of hBN were prepared by atmospheric plasma-spray technology. The microstructural, mechanical, and tribological properties of the coatings were systematically investigated. The results show that the flowability and apparent density of NiCr/Cr₃C₂-hBN composite powders, as well as the microhardness and tensile strength of the NiCr/Cr₃C₂-hBN composite coating, gradually decrease with the increase of hBN in the composite powders. The addition of hBN is benefit to the friction coefficient of the coatings, but it is positive to the wear rate. When the content of hBN is up to 20%, the friction coefficient of the composite coating is lowest, but the wear rate of the composite coating is highest.     

Influence of FeCrAl Content on Microstructure and Bonding Strength of Plasma-Sprayed FeCrAl/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Coatings

Low-power plasma-sprayed FeCrAl/Al₂O₃ composite coatings with 1.5 mm thickness have been fabricated for radar absorption applications. The effects of FeCrAl content on the coating properties were studied. The FeCrAl presents in the form of a few thin lamellae and numerous particles, demonstrating relatively even distribution in all the coatings. Results show that the micro-hardness and porosity decrease with the increase in FeCrAl content. With FeCrAl content increasing from 28 to 47 wt.%, the bonding strength of the coatings with 1.5 mm thickness increases from 10.5 to 27 MPa, and the failure modes are composed of cohesive and adhesive failure, which are ascribed to the coating microstructure and the residual stress, respectively.     

The Microstructure and Thermoelectric Properties of Yb-Filled Skutterudite Yb<Subscript>0.1</Subscript>Co<Subscript>4</Subscript>Sb<Subscript>12</Subscript> Under Cyclic Thermal Loading

This paper is devoted to investigating the microstructure and thermoelectric properties of Yb-filled skutterudite Yb_0.1Co₄Sb₁₂ under a cyclic thermal loading from room temperature to 773 K. The results indicate after 1000 cycles, the surface morphology changes dramatically, and clear grain boundaries appear on the surface of the sample. The grain sizes of the sample change little after 1000 cycles, and the main phase is still skutterudite; however, a trace amount of YbSb also exists. In addition, the electrical conductivity and thermal conductivity decrease distinctly after 1000 cycles, but the absolute value of the Seebeck coefficient increases a little. Consequently, the ZT value decreases slightly from 0.75 at 800 K before cycling to 0.69 after 1000 cycles. It indicates that the effect of the cyclic thermal loading on the ZT of the Yb_0.1Co₄Sb₁₂ material is not distinct.     

Microstructure Characterization of the FeAl<Subscript>2</Subscript>O<Subscript>4</Subscript>-Based Nanostructured Composite Coating Synthesized by Plasma Spraying Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al Powders

The microstructure of the coating prepared by reactive plasma spraying Fe₂O₃/Al composite powders was characterized by x-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The results indicated that the coating exhibited nanostructured microstructure which consisted of FeAl₂O₄, Fe or Fe solid solution, Al₂O₃ and a little FeAl. In the composite coating, spherical Fe particles (tens of nanometers to hundreds of nanometers) were distributed uniformly within the equiaxed and columnar nanograins FeAl₂O₄ matrix. There were two kinds of Al₂O₃ phases present in the composite coating. One kind was nano-sized Al₂O₃ particles uniformly dispersed within the matrix, forming eutectic structure of (FeAl₂O₄ + γ-Al₂O₃); the other was 1-1.5 μm Al₂O₃ particles embedded individually within the matrix. The composite coating had higher toughness than the conventional microstructured Al₂O₃ coating.     

Suspension Plasma-Sprayed ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> Nanostructured Coatings for ppm-Level Acetone Detection

Zinc ferrite (ZnFe₂O₄) sensitive coatings have been deposited by suspension plasma spraying. The phase constitution of the coatings was characterized by x-ray diffraction while the top surface and cross-sectional morphology of the coatings were inspected by scanning electron microscopy. The response to acetone was tested with the concentration in the range of 25-500 ppm at the working temperature from 175 to 275 °C. The sensors that were deposited at an arc current of 400 A showed better performance than those at 600 A owing to small grain size and high porosity. The sensor response increased with acetone concentration. The optimized sensors showed excellent response/recovery time and selectivity to acetone at 200 °C.     

Chemical Stability and Biological Properties of Plasma-Sprayed CaO-SiO<Subscript>2</Subscript>-ZrO<Subscript>2</Subscript> Coatings

In this work, calcia-stabilized zirconia powders were coated by silica derived from tetraethoxysilane (TEOS) hydrolysis. After calcining at 1400 °C, decalcification of calcia-stabilized zirconia by silica occurred and powders composed of Ca₂SiO₄, ZrO₂, and CaZrO₃ were prepared. We produced three kinds of powders with different Ca₂SiO₄ contents [20 wt.% (denoted as CZS2), 40 wt.% (denoted as CZS4), and 60 wt.% (denoted as CZS6)]. The obtained powders were sprayed onto Ti-6Al-4V substrates using atmospheric plasma spraying. The microstructure of the powders and coatings were analyzed. The dissolution rates of the coatings were assessed by monitoring the ions release and mass losses after immersion in Tris-HCl buffer solution. Results showed that the chemical stability of the coatings were significantly improved compared with pure calcium silicate coatings, and increased with the increase of Zr contents. The CZS4 coating showed not only good apatite-formation ability in simulated body fluid, but also well attachment and proliferation capability for the canine bone marrow stem cells. Results presented here indicate that plasma-sprayed CZS4 coating has medium dissolution rate and good biological properties, suggesting its potential use as bone implants.     

Tribological Properties of Ni<Subscript>3</Subscript>Al Matrix Composite Sliding Against Si<Subscript>3</Subscript>N<Subscript>4</Subscript>, SiC and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> at Elevated Temperatures

The Ni₃Al matrix self-lubricating composite was fabricated by powder metallurgy technique. The tribological behavior of the composite sliding against commercial Si₃N₄, SiC and Al₂O₃ ceramic balls was investigated from 20 to 1000 °C. It was found that the composite demonstrated excellent lubricating properties with different friction pairs at a wide temperature range, which can be attributed to the synergetic effect of Ag, fluorides, and molybdates formed by oxidations. The Ni₃Al matrix self-lubricating composite/Si₃N₄ couple possessed the stable friction coefficient and wear rate.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Content on Electrical Breakdown Properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Cu Composite

Al₂O₃/Cu composites were prepared by external addition of Al₂O₃, and the effect of Al₂O₃ content on microstructure, density, hardness, electrical conductivity and vacuum electrical breakdown properties was studied. The results show that with increasing Al₂O₃ addition, the density of Al₂O₃/Cu composite significantly decreases, the hardness sharply increases and then slowly decreases, but the electrical conductivity invariably decreases. The vacuum breakdown test shows that with increasing Al₂O₃ addition, the breakdown strength first sharply increases and then decreases when the Al₂O₃ content exceeds 1.2 wt.%; the chopping current always exhibits a decreasing trend and the arc life first increases and then decreases. According to the morphology of arc erosion and analysis, the arc erosion resistance increases and then decreases sharply. In the range of experiments, the optimal arc erosion resistance of Al₂O₃/Cu composite can be obtained with the addition of 1.2 wt.% Al₂O₃.