Improvement of electrical conductivity of PEDOT:PSS films by 2-Methylimidazole post treatment

The electrical conductivity of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films was significantly improved without losing the optical transparency by treating the films with solution of 2-Methylimidazole in ethanol. The maximum electrical conductivity of such a thin film reached 930 S cm⁻¹, more than 1150 order of magnitude higher than that of pure PEDOT:PSS film. The mechanism of conductivity enhancement of treated thin PEDOT:PSS films was explored by atomic force microscopy (AFM) and UV/VIS spectrophotometer. The AFM scans show that the surface of the 2-Methylimidazole treated PEDOT:PSS layer is smoother than that of the pristine PEDOT:PSS thin film. Improvement in the morphology, electrical and optical properties of PEDOT:PSS films makes them highly suitable for numerous applications in optoelectronic devices.     

Optical properties and conductivity of PEDOT:PSS films treated by polyethylenimine solution for organic solar cells

We report on conductivity and optical property of three different types of poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) films [pristine PH1000 film (PH1000-p), with 5 wt.% ethylene glycol additive (PH1000-EG) and with sulfuric acid post-treatment (PH1000-SA)] before and after polyethylenimine (PEI) treatment. The PEI is found to decrease the conductivity of all the PEDOT:PSS films. The processing solvent of 2-methoxyethanol is found to significantly enhance the conductivity of PH1000-p from 1.1 up to 744 S/cm while the processing solvent of isopropanol or water does not change the conductivity of PH1000-p much. As for the optical properties, the PEI treatment slightly changes the transmittance and reflectance of PH1000-p and PH1000-EG films, while the PEI leads to an substantial increase of the absorptance in the spectral region of 400–1100 nm of the PH1000-SA films. Though the optical property and conductivity of the three different types of PEDOT:PSS films vary with the PEI treatment, the treated PEDOT:PSS films exhibit similar low work function. We demonstrate solar cells with a simple device structure of glass/low-WF PEDOT:PSS/P3HT:ICBA/high-WF PEDOT:PSS cells that exhibit good performance with open-circuit voltage of 0.82 V and fill factor up to 0.62 under 100 mW/cm² white light illumination.     

The enhancement of electrical and optical properties of PEDOT:PSS using one-step dynamic etching for flexible application

The conductivity enhancement of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) by dynamic etching process was investigated to introduce the outstanding and simplest method for soft electronics. Four different samples which were pristine PEDOT:PSS, PEDOT:PSS doped with 5 wt.% DMSO, PEDOT:PSS with dipping process, and PEDOT:PSS with dynamic etching process were prepared to compare the properties such as conductivity, morphology, relative atomic percentage, and topography. All samples were characterized by four point probe, current atomic force microscopy (C-AFM), X-ray photoelectron spectroscopy (XPS), and UV–visible spectroscopy. The conductivity of the sample with dynamic etching process showed the highest value as 1299 S/cm among four samples. We proved that the dynamic etching process is superior to remove PSS phase from PEDOT:PSS film, to flow strong current through entire surface of PEDOT:PSS, and to show the smoothest surface (RMS 2.28 nm). XPS analysis was conducted for accurate chemical and structural surface environments of four samples and the relative atomic percentage of PEDOT in the sample with dynamic etching was the highest as 29.5%. The device performance of the sample with the dynamic etching process was outstanding as 10.31 mA/cm² of J_sc, 0.75 eV of V_oc, 0.46 of FF, and 3.53% of PCE. All properties and the device performance for PEDOT:PSS film by dynamic etching process were the most excellent among the samples.     

Effects of tetramethylene sulfone solvent additives on conductivity of PEDOT:PSS film and performance of polymer photovoltaic cells

A solvent additive in PEDOT:PSS solution is one of many methods to improve the conductivity of the poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films. We explore a new type of the solvent additive, namely tetramethylene sulfone (TMS), for the fabrication of the PEDOT:PSS conductive layer in the ITO/PEDOT:PSS/P3HT:PCBM/TiO_x/Al polymer photovoltaic cells, in comparison to a more common dimethyl sulfoxide (DMSO) solvent additive. At optimal conditions, the TMS additive at 10 wt.% has been found to enhance the conductivity of pristine PEDOT:PSS films from 0.04 S/cm up to approximately 189 S/cm, compared with the highest conductivity for the case of the DMSO additive at 15 wt.% of 117 S/cm. Possible mechanisms of this conductivity enhancement, relating to the polymer conformation and the film morphology, have been investigated by Raman spectroscopy, X-ray diffraction, atomic force microscopy, and transmission electron microscopy. The performance of the polymer photovoltaic cells fabricated with the solvent additives PEDOT:PSS films follows a similar trend to the conductivity of the films as a function of the additive concentration. The additives mainly lead to greater short circuit current density (J_sc) of the photovoltaic cells. The highest power conversion efficiency (PCE) of 2.24% of the device has been obtained with the 10 wt.% TMS additive of, compared to the PCE of 1.48% for the standard device without solvent additive.     

Handheld and automated ultrasonic spray deposition of conductive PEDOT:PSS films and their application in AC EL devices

In this contribution we explore the spray deposition technique to achieve smooth films based on the conductive polymer PEDOT:PSS. Two different spray systems were used and compared namely: (a) handheld airbrush and (b) automated ultrasonic spray system. For each system a number of parameters were pre-adjusted during coating control experiments such as spray head distance, angle and cone for airbrush as well as flow rate, power and focus for ultrasonic nozzle. Water-based solutions of PEDOT:PSS having 20% of N-methylpyrrolidone (NMP) were sprayed on glass substrates at temperatures ranging from 75 to 150 °C. The resulting films were further chemically treated with ethylene glycol (EG) and evaluated with respect to their morphological, electrical and optical properties. Before EG-treatment the ultrasonic spraying resulted in smoother films with conductivity up to 2–3.9 times higher than their airbrushed counterparts. Deposition temperature proved to have minor effect on the morphological and electro-optical properties of PEDOT:PSS films. On the other hand, the film conductivity was enhanced, peaking at 610.1 S cm⁻¹ for ultrasonic spraying, when further chemically modified by EG. IR microspectroscopy mapping analysis, Raman spectroscopy and XRD data indicated a phase-separation between PEDOT and PSS chains and increasing crystallinity in the ultrasonically sprayed films. The application of such PEDOT:PSS films as transparent electrode in flexible AC EL devices is demonstrated.     

Composite film of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) and MoO3 as an efficient hole injection layer for polymer light-emitting diodes

We demonstrate improved performances in polymer light-emitting diodes (PLEDs) using a composite film of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and MoO₃ powder as a hole injection layer. The PLED with the composite film exhibits the current efficiency of 13.5 cd/A, driving voltage of 3.4 V, and half lifetime of 108.1 h, while those values of the PLED with a pristine PEDOT:PSS was 11.3 cd/A, 3.8 V, and 41.5 h, respectively. We also analyze the morphological, optical and electrical properties of the composite films by atomic force microscopy (AFM), UV–Vis-IR absorption, and ultraviolet photoemission spectroscopy (UPS). This work suggests that mixing MoO₃ into PEDOT:PSS is a simple and promising technique for use solution-based devices as an hole injection layer.     

Transparent and flexible amorphous InZnAlO films grown by roll-to-roll sputtering for acidic buffer-free flexible organic solar cells

We report on transparent and flexible amorphous In–Zn–Al–O (a-IZAO) films prepared by roll-to-roll (RTR) sputtering for use as anodes in acidic buffer free flexible organic solar cells (FOSCs). The presence of Zn and Al structural stabilizers in the In₂O₃ matrix produced a completely amorphous structure with the high optical transmittance of 89.25% and the low resistivity of 2.123 × 10⁻³ Ω-cm, as well as the high work function of 5.14 eV, making the a-IZAO films suitable for use as flexible anodes for FOSCs. In addition, the a-IZAO films showed no change in resistance (ΔR) during outer and inner bending fatigue tests due to their good mechanical flexibility. Relative to the power conversion efficiency (1.944%) of a PEDOT:PSS-based FOSCs, a FOSC fabricated by using an a-IZAO anode and without the use of acidic PEDOT:PSS buffer showed greater power conversion efficiency (2.509%), owing to the absence of interfacial reactions between the acidic PEDOT:PSS and the a-IZAO anode.     

Thermal degradation mechanisms of PEDOT:PSS

The thermal stability of thin (50 nm) PEDOT:PSS films, was investigated by dc conductivity measurements, X-ray and UV photoelectron spectroscopies as a function of heating temperature and heating time. The mechanism of electrical conductivity as a function of temperature is consistent with a hopping type carrier transport. The electrical conductivity decreased, as a function of time, in agreement with a granular metal type structure, in which aging is due to the shrinking of the PEDOT conductive grains. XPS and UPS spectra indicate that conformational changes of the PEDOT:PSS film are responsible for this behaviour and a model for these modifications is proposed.     

Stable organic photovoltaic with PEDOT:PSS and MoOX mixture anode interfacial layer without encapsulation

Herein, we report about an efficient and stable organic photovoltaic that uses a poly(3,4-ethylenedioxythiophene):poly(styrene-sulfonate) (PEDOT:PSS) and molybdenum oxide (MoO_X) mixture for the anode interfacial layer, and that can reach 4.43% power conversion efficiency (PCE) under AM1.5 conditions. Utilizing PEDOT:PSS:MoO_X (1:1), the shelf lifetime of poly(3-hexylthiophene) (P3HT), and indene-C₆₀ bisadduct (ICBA)-based solar cells without encapsulation, can be realized with only a 25% deterioration after 672 h of storage in air. Furthermore, we compare the photovoltaic performance of the P3HT:ICBA-based organic photovoltaic with PEDOT:PSS, and PEDOT:PSS:MoO_X, in which PEDOT:PSS:MoO_X has outperformed the others. In addition, the water vapor transmission rate of PEDOT:PSS:MoO_X is 0.17 gm/(m² day), which is much less than that of PEDOT:PSS.     

ITO-free organic solar cells using highly conductive phenol-treated PEDOT:PSS anodes

Phenol as one of the most polar solvent was used to enhance the conductivity of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films. The conductivity of PEDOT:PSS films improved to 1193 S/cm after treatment with phenol vapor and 1054 S/cm after treatment with phenol drop. The treated films also showed high transmittance in the visible region which is one of the crucial factors for optoelectronic devices such as organic solar cells and light emitting diodes. The mechanism of conductivity enhancement of treated thin PEDOT:PSS films was investigated by atomic force microscopy (AFM) and UV/Vis spectrophotometer. The AFM images showed that the ratio of PEDOT to PSS at top most of the surface was increased for treated film. Rearrangement of PEDOT segment throughout the film and hence conformational changes are the reasons for enhancement of conductivity. The modified PEDOT:PSS films were used as electrode for ITO-free organic solar cells (OSCs). These ITO-free OSCs showed almost equal operation to those for ITO electrodes.     

Pt–free counter electrodes based on modified screen–printed PEDOT:PSS catalytic layers for dye–sensitized solar cells

One of the most highlighted advantages of dye-sensitized solar cells (DSSCs) consists in the possibility to apply simple and low-cost printing techniques and solution processable materials for their assembling. Here, we report on screen-printed Pt–free counter electrodes (CEs) based on poly(3,4–ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) dispersions with different content of rheological agent – hydroxyethyl cellulose (HEC). These PEDOT:PSS dispersions, having measured pseudoplastic and thixotropic rheological behaviour, were screen–printed onto FTO glasses. The content of rheological agent in PEDOT:PSS catalytic layers showed an effect on measured thickness, electrochemical properties, specific conductivity and subsequently on the evaluated photovoltaic performance of DSSCs. The PEDOT:PSS CE with the 0.03 wt% of HEC achieved the best electrochemical performance and specific conductivity (80 S cm⁻¹), the lowest thickness of 200 nm and transparency in VIS light spectrum over 60%. DSSCs based on this PEDOT:PSS CE reached the highest conversion efficiency of 4.2% which is only approximately 40% lower value than η=6.9% evaluated for Pt CE.     

Conductivity,work function,and environmental stability of PEDOT:PSS thin films treated with sorbitol

The electrical properties of poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) thin films deposited from aqueous dispersion using different concentrations of sorbitol have been studied in detail. Although it is well known that sorbitol enhances the conductivity of PEDOT:PSS thin films by three orders of magnitude, the origin and consequences of sorbitol treatment are only partly understood and subject of further study. By thermal annealing of spin coated PEDOT:PSS/sorbitol films and simultaneously monitoring the conductivity, we demonstrate that the strong increase in conductivity coincides with evaporation of sorbitol from the film. Hence, sorbitol is a processing additive rather than a (secondary) dopant. Scanning Kelvin probe microscopy reveals that sorbitol treatment causes a reduction of the work function from 5.1 eV to 4.8–4.9 eV. Sorbitol also influences the environmental stability of the films. While the conductivity of the pristine PEDOT:PSS films increases by about one order of magnitude at ∼50% RH due to an ionic contribution to the overall conductivity, films prepared using sorbitol exhibit an increased environmental stability with an almost constant conductivity up to 45% RH and a slight decrease at 50% RH. The higher stability results from a reduced tendency to take up water from the air, which is attributed to a denser packing of the PEDOT:PSS after sorbitol treatment.     

A facile chemical reduction approach for effectively tuning thermoelectric properties of PEDOT films

Poly(3,4-ethylenedioxythiophene)–tosylate–polyethylene glycol–polypropylene glycol–polyethylene glycol (PEDOT–Tos–PPP) films were prepared via a vapor phase polymerization (VPP) method. The films possess good electrical conductivity (1550 S cm⁻¹), low Seebeck coefficient (14.9 μV K⁻¹) and thermal conductivity (0.501 W m⁻¹ K⁻¹), and ZT ∼ 0.02 at room temperature (RT, 295 K). Then, the films were treated with NaBH₄/DMSO solutions of different NaBH₄ concentrations to adjust the redox level. After the NaBH₄/DMSO treatment (dedoping), the electrical conductivity of the films continuously decreased from 1550 to 5.7 S cm⁻¹, whereas the Seebeck coefficient steeply increased from 14.9 to 143.5 μV K⁻¹. A maximum power factor of 98.1 μW m⁻¹ K⁻² has been achieved at an optimum redox level. In addition, the thermal conductivity of the PEDOT–Tos–PPP films decrease from 0.501 to 0.451 W m⁻¹ K⁻¹ after treated with 0.04% NaBH₄/DMSO solution. A maximum ZT value of 0.064 has been achieved at RT. The electrical conductivity and thermal conductivity (Seebeck coefficient) of the untreated and 0.04% NaBH₄/DMSO treated PEDOT–Tos–PPP films decrease (increases) with increasing temperature from 295 to 385 K. And the power factor of the films monotonically increases with temperature. The ZT at 385 K of the 0.04% NaBH₄/DMSO treated film is 0.155.     

Transverse charge transport in inkjet printed poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS)

Transverse (z) alignment of PEDOT grains was demonstrated in inkjet printed PEDOT:PSS. This explained the superior transverse charge conduction mode in inkjet printed PEDOT:PSS films, best fitted by the Efros-Shklovskii 1D-VRH (variable range hopping) model in this study compared with spin coated PEDOT:PSS films, which have demonstrated layers of generally in-plane aligned PEDOT:PSS grains. The findings of this study, regarding the microstructure of inkjet printed PEDOT:PSS films and their transverse charge transport model, justify measurements of the transverse conductivity of inkjet printed films in this study being 600 times higher than that of spin coated films. In addition, it was found that the addition of 5 wt% DMSO in the printing PEDOT:PSS ink lowers the workfunction by 3% approximately.     

Indium zinc oxide ohmic contact to poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) induced by UV light

In this research, we investigated the I–V characteristics of ITO/PEDOT:PSS/InZnO devices for two sets of samples. The first set is composed of PEDOT:PSS as-prepared, while the second set is composed of PEDOT:PSS irradiated by UV light source. We found that UV irradiation improves the electrical conductivity of the fabricated devices and yields to ohmic contact. Based on the UPS measurements, it was found that UV irradiation leads to an increase in the work function and the enhancement of electrical conductivity of PEDOT:PSS films. XPS and AFM measurements indicate that conformational changes of the PEDOT:PSS films are responsible for this behavior. We also studied the effect of storage on the electrical properties of our devices. No significant changes of electrical characteristics have been found after storing the devices for a period of 30 days.     

All-solution-processed inverted polymer solar cells on granular surface-nickelized polyimide

In this study, we prepared all-solution-processed inverted polymer solar cells (PSCs) incorporating two solution-processed electrodes – surface-nickelized polyimide films (NiPI films) as cathodes and high-conductivity poly(3,4-ethylenedioxythiophene)/poly(styrene-sulfonate) (PEDOT:PSS) films as anodes – and an active layer with a bulk heterojunction morphology of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C₆₁-buytyric acid methyl ester (PCBM). The granular Ni thin films, which exhibited good adhesion and high-conductivity (ca. 2778 S cm^?1) on the polyimide (PI) substrates and possessed a work function different from that of pure Ni metal (WF, 5.4 eV). Using ultraviolet photoelectron spectroscopy, we determined that the WF of the NiPI films was ca. 3.9 eV. Prior to the coating of the photoactive layer, the surface of the NiPI films were treated with titanium(diisopropoxide)bis(2,4-pentanedionate) (TIPD) solution to facilitate the deposition of high-quality active layer and further as a hole blocking layer. The solution processed anodes (solvent-modified PEDOT:PSS films) were further coated and subjected to mild oxygen plasma treatment on the active layer. Short exposure (5 s) to the plasma improved the quality of the surface of the active layer for PEDOT:PSS deposition. These inverted PSCs on flexible granular NiPI films provided a power conversion efficiency of 2.4% when illuminated under AM 1.5 conditions (100 mW cm^?2). The phenomenon of light absorption enhancement in those inverted PSCs was observed as indicated in reflective UV–vis, haze factor and external quantum efficiency (EQE) responses. The resulting fill factor (FF) of 0.43 is still significantly lower than the FF of 0.64 for standard devices. When compared to the planar structure, the improvement of absorbance of light and good haze factors was obtained for granular structure which suggests NiPI as a better back contact electrode through enhancing the light trapping and scattering in inverted PSCs.     

In-situ modification of PEDOT:PSS work function using alkyl alcohols as secondary processing solvents and their impact on merocyanine based bulk heterojunction solar cells

The influence of a series of alkyl alcohols on the work function of PEDOT:PSS thin films is systematically investigated by Kelvin probe measurements. We show that the PEDOT:PSS work function can be increased stepwise from 5.2 eV for pristine PEDOT:PSS to 5.61 eV using either alcohols with different alkyl chain length or varying the amount of alcohol in mixtures with chlorobenzene. Moreover, we demonstrate the effect of work function modification on merocyanine based bulk heterojunction solar cells, resulting in improved values for the open-circuit voltage comparable to those obtained with high work function MoO₃. Thus, the processing method presented herein can potentially serve as a simple, alternative route to adjustable and high work function electrodes while maintaining processability from solution.     

Adhesion properties of inverted polymer solarcells: Processing and film structure parameters

We report on the adhesion of weak interfaces in inverted P3HT:PCBM-based polymer solar cells (OPV) with either a conductive polymer, PEDOT:PSS, or a metal oxide, molybdenum trioxide (MoO₃), as the hole transport layer. The PEDOT:PSS OPVs were prepared by spin or spray coating on glass substrates, or slot-die coating on flexible PET substrates. In all cases, we observed adhesive failure at the interface between the P3HT:PCBM with PEDOT:PSS layer. The adhesion energy measured for the solar cells made on glass substrates was about 1.8 J/m², but only 0.5 J/m² for the roll-to-roll processed flexible solar cells. The adhesion energy was insensitive to the PEDOT:PSS layer thickness in the range of 10–40 nm. A marginal increase in adhesion energy was measured with increased O₂ plasma power. Compared to solution processed PEDOT:PSS, we found that thermally evaporated MoO₃ adheres less to the P3HT:PCBM layer, which we attributed to the reduced mixing at the MoO₃/P3HT:PCBM interface during the thermal evaporation process. Insights into the mechanisms of delamination and the effect of different material properties and processing parameters yield general guidelines for the design of more reliable organic photovoltaic devices.     

Explaining the effects of processing on the electrical properties of PEDOT:PSS

By simultaneously measuring the Seebeck coefficient and the conductivity in differently processed PEDOT:PSS films, fundamental understanding is gained on how commonly used processing methods improve the conductivity of PEDOT:PSS. Use of a high boiling solvent (HBS) enhances the conductivity by 3 orders of magnitude, as is well-known. Simultaneously, the Seebeck coefficient S remains largely unaffected, which is shown to imply that the conductivity is improved by enhanced connectivity between PEDOT-rich filaments within the film, rather than by improved conductivity of the separate PEDOT filaments. Post-treatment of PEDOT:PSS films by washing with H₂SO₄ leads to a similarly enhanced conductivity and a significant reduction in the layer thickness. This reduction strikingly corresponds to the initial PSS ratio in the PEDOT:PSS films, which suggests removal and replacement of PSS in PEDOT:PSS by HSO₄⁻ or SO₄²⁻ after washing. Like for the HBS treatment, this improves the connectivity between PEDOT filaments. Depending on whether the H₂SO₄ treatment is or is not preceded by an HBS treatment also the intra-filament transport is affected. We show that by characterization of S and σ it is possible to obtain more fundamental understanding of the effects of processing on the (thermo)electrical characteristics of PEDOT:PSS.     

Doped PEDOT:PSS electrodes,patterned through wettability control,and their effects on the electrical properties of polymer thin film transistors

The water−based conductive polymer, poly(3,4−ethylenedioxythiophene), doped with poly(styrene sulfonate) (PEDOT:PSS), has received much attention for its utility as a printable electrode due to its transparency, thermal stability, and processability; however, the electrical properties of devices prepared with printed PEDOT:PSS electrodes are generally inferior to those of devices fabricated with evaporated metal electrodes or their inorganic counterparts. Here, we show that the electrical performances of polymer thin film transistors could be improved by doping the PEDOT:PSS chains used as source and drain electrodes. The addition of HAuCl₄ to the PEDOT:PSS solution increased the electrical conductivity and work function of the electrodes. The PEDOT:PSS film doped with 10 mM HAuCl₄ provided a field effect mobility exceeding 0.01 cm²V⁻¹s⁻¹, a factor of 7 greater than the value obtained from the device prepared with pristine PEDOT electrodes.