Ba(Zn1/3Nb2/3)O3/Ni0.8Zn0.2Fe2O4 magneto-dielectric composite with large dielectric constant and high permeability

Ba(Zn_1/3Nb_2/3)O₃/Ni_0.8Zn_0.2Fe₂O₄ (BZN/NZO) composites were synthesized via the conventional solid-state reaction method. The phase composition and surface morphology of the composites were investigated using XRD and SEM, respectively. The dielectric and magnetic properties of the composites were studied. The results show that the BZN/NZO composites have large dielectric constants and very high permeabilities. For the 20%BZN/80%NZO composite, the dielectric constant and permeability in low frequency range are about 8,000 and 18, respectively. The large dielectric behavior of the BZN/NZO composites is mainly attributed to the Maxwell–Wagner polarization.     

Magnetic and dielectric properties of the M-type barium strontium hexaferrite (Ba x Sr1−x Fe12O19) in the RF and microwave (MW) frequency range

This paper presents results for the dielectric permittivity (ε′), dielectric loss (tg δ _E) dielectric permeability (μ′) and magnetic loss (tg δ _M) in the radio-frequency and microwave frequency range of Ba _x Sr_1−x Fe₁₂O₁₉ hexaferrite (0 ≤ x ≤ 1). The samples were prepared by a new route of the ceramic method. The magnetic permeability (μ′) and magnetic loss (tg δ _M) measurements in the range 100 MHz to 1.5 GHz, reveals that 1.32 ≤ μ′ ≤ 1.68 for the permeability of BFO100 (BaFe₁₂O₁₉) and 1.16 < μ′ ≤ 1.88 for SFO100 (SrFe₁₂O₁₉) in the range of studied frequencies. The BFO100 sample presented lower loss (tg δ _M = 4.10⁻³ at 1.5 GHz). The permittivity of BFO100 and SFO100 in 1.5 GHz are, respectively 8.18 and 8.19, and in the 1 MHz are, respectively 52.04 and 19.09. The samples presented coercive field in the range of 3–5 kOe and remanence magnetization in the range of 33–36 emu/g. The subjects of paper were study the dielectric and magnetic properties of the barium and strontium hexaferrite, in view of applications as a material for permanent magnets, high density magnetic recording and microwave devices.     

Dielectric and ferromagnetic properties of BaTiO<Subscript>3</Subscript>/Ni<Subscript>0.93</Subscript>Co<Subscript>0.02</Subscript>Cu<Subscript>0.05</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> composites

xBaTiO₃ + (1 − x)Ni_0.93Co_0.02Cu_0.05Fe₂O₄ (x = 0.5, 0.6, 0.7, 0.8) composites with ferroelectric–ferromagnetic characteristics were synthesized by the ceramic sintering technique. The presence of constituent phases in the composites was confirmed by X-ray diffraction studies. The average grain size was calculated by using a scanning electron micrograph. The dielectric characteristics were studied in the 100 kHz to 15 MHz. The dielectric constant changed higher with ferroelectric content increasing; and it was constant in this frequency range. The relation of dielectric constant with temperature was researched at 1, 10, 100 kHz. The Curie temperature would be higher with frequency increasing. The hysteresis behavior was studied to understand the magnetic properties such as saturation magnetization (M _s). The composites were a typical soft magnetic character with low coercive force. Both the ferroelectric and ferromagnetic phases preserve their basic properties in the bulk composite, thus these composites are good candidates as magnetoelectric materials.     

TiO2-nanorod decorated carbon nanotubes for high-permittivity and low-dielectric-loss polystyrene composites

Polymer composites with high permittivity and low dielectric loss are highly desirable in electronic and electrical industry. Adding conductive fillers could significantly increase the permittivity of a polymer. However, polymer composites containing conductive fillers often exhibit very high dielectric loss due to their large electrical conduction or leakage currents. In this work, by engineering TiO₂-nanorod-decorated multi-walled carbon nanotubes (TD-CNTs), polystyrene (PS) composite with high permittivity and low dielectric loss have been successfully prepared. The composite containing of 17.2 vol.% TD-CNTs has a permittivity of 37 at 1 kHz, which is 13.7 times higher than that of the pure PS (2.7), while the dielectric loss still remains at a low value below 0.11. The dielectric properties of the composites are closely related to the length of CNTs and the loading level of TiO₂-nanorods on the CNT surfaces.     

Three-phase polymer–ceramic–metal composite for embedded capacitor applications

This paper addresses the materials and processes for printed wiring board compatible embedded capacitor using ceramic, polymer and metal. The Ca[(Li_1/3Nb_2/3)_0.8Ti_0.2]O_3?δ (CLNT)–epoxy–silver, three-phase composites were prepared by two step mixing and thermosetting technique. The dielectric properties of the three-phase composites were investigated in terms of volume fraction of silver, temperature and frequency. The dielectric properties of epoxy–CLNT composites were compared with theoretical predictions. The relative permittivity of the three-phase composites increased with silver loading. Addition of 0.28 volume fraction of silver increases the relative permittivity of epoxy–CLNT composites from 8 to 142 at 1 MHz. This composite is flexible and can be fabricated into various shapes with low processing temperature.     

Magnetodielectric composite with ferrite inclusions as substrates for microstrip patch antennas at microwave frequencies

A study has been conducted to estimate the complex permittivity and permeability along with magnetic characterization of different volume fractions of magnetodielectric composites with cobalt ferrite nano inclusions. Using an in touch superstrate technique dielectric properties are estimated. Cavity perturbation technique is used to study the complex permeability of the samples. 4πM_s value and coercivity is measured using vibrating sample magnetometry. Structural and surface morphologies on the composite samples are conducted to determine the size and homogeneous distribution of nano inclusions. The average grain size of cobalt ferrite nanoparticles is found to be ～10 nm. The real part of permittivity and permeability of the samples varies from ～1–2.905 to ～1.01–1.05 with increase in inclusion content from 1% VF to 5% VF, respectively. The tan δ of permittivity and imaginary part of permeability is found to be of the order of ～10^?3 and ～10^?1 respectively. Verification of these composites as potential substrates for microstrip patch antenna is carried out by fabricating simple rectangular patch at 9.5 GHz using transmission line model. Rectangular patch is designed on 5% VF composite system. The return loss for the composite system was found to be ～?19.451 dB which is comparable with that designed on standard glass epoxy substrate (?_r = 4.5).     

Dielectric and magnetic properties of Ca(Zn<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript>/NiZn ferrite composites

Dense Ca(Zn_1/3Nb_2/3)O₃/NiZn ferrite composites with homogeneously fine microstructures were prepared through conventional solid-state method. The powder XRD patterns confirm the coexistence of the two phases. The dielectric properties in the low frequency range (100 Hz–1 MHz) follow the rule of Maxwell–Wagner interfacial polarization. The dielectric and magnetic properties in the high frequency range (10 MHz–1 GHz) are also reported. The results show that this kind of magnetic–dielectric composites could be used in high-frequency communications for the capacitor-inductor integrating devices such as electromagnetic interference filters and antennas.     

Layered dielectric–magnetic composite structures for Rf-applications

In this paper multilayer magnetic–dielectric composite structures for high frequency applications are introduced. The 0–3 type dielectric and magnetic composites with homogeneously distributed ceramic inclusions were fabricated by mixing extrusion and injection moulding. Magnetic Yttrium Iron Garnet (YIG) and Z-type Hexaferrite (HexaZ) as well as paraelectric Barium Strontium Titanate (BST) powders were used to enhance the permittivity and permeability of the composites. The magnetic–dielectric multilayer composites were constructed by hot-laminating magnetic and dielectric layers in turn to create a solid 2-2 type composite structure. The microstructure, high frequency dielectric and magnetic properties of individual layers and 2-2 composites were investigated and measured. The measurement results indicate that such multimaterial multilayer structures are good candidates for components with reduced dielectric and magnetic losses. Moreover, the observed good frequency stability and the cut-off frequencies above 1 GHz suggested that the composites could be utilized in, e.g., sophisticated functional circuit boards and RF devices.     

Enhanced thermal conductivity and dielectric properties of Al/β-SiCw/PVDF composites

Polymeric composites with high thermal conductivity, high dielectric permittivity but low dissipation factor have wide important applications in electronic and electrical industry. In this study, three phases composites consisting of poly(vinylidene fluoride) (PVDF), Al nanoparticles and β-silicon carbide whiskers (β-SiC_w) were prepared. The thermal conductivity, morphological and dielectric properties of the composites were investigated. The results indicate that the addition of 12 vol% β-SiC_w not only improves the thermal conductivity of Al/PVDF from 1.57 to 2.1 W/m K, but also remarkably increases the dielectric constant from 46 to 330 at 100 Hz, whereas the dielectric loss of the composites still remain at relatively low levels similar to that of Al/PVDF at a wider frequency range from 10⁻¹ Hz to 10⁷ Hz. With further increasing the β-SiC_w loading to 20 vol%, the thermal conductivity and dielectric constant of the composites continue to increase, whereas both the dielectric loss and conductivity also rise rapidly.     

Dielectric,thermal and mechanical properties of Sr<Subscript>2</Subscript>ZnSi<Subscript>2</Subscript>O<Subscript>7</Subscript> based polymer/ceramic composites

Polymer/Sr₂ZnSi₂O₇ (SZS) ceramic composites suitable for substrate applications have been developed using the polymers polystyrene (PS), high density polyethylene (HDPE) and Di-Glycidyl Ether of Bisphenol A (DGEBA). The dielectric, thermal and mechanical properties of the composites are investigated as a function of various concentrations of the ceramic filler. The obtained values of relative permittivity, dielectric loss tangent, thermal conductivity and coefficient of thermal expansion of the composites are compared with the corresponding theoretical predictions. The relative permittivity of the polymer/ceramic composites increases with filler loading. The dielectric loss tangent also shows the same trend except for DGEBA/SZS composites. The major advantages of the ceramic loading are improvement in thermal conductivity and a decrease in the coefficient of thermal expansion. The tensile strength of the composites decreases with increase in filler content, whereas an improvement is observed in microhardness. The variation of relative permittivity (at 1 MHz) of the composites is also studied as a function of temperature.     

Influence of copper substitution on magnetic and electrical properties of MgCuZn ferrite prepared by microwave sintering method

Polycrystalline MgCuZn ferrites with chemical formula Mg_0.50-xCu_xZn_0.50Fe₂O₄ (x = 0.00, 0.05, 0.10, 0.15, 0.20, 0.25 and 0.30) were prepared by microwave sintering method. These powders were calcined, compacted and sintered at 950 °C for 30 min. Structural, microstructural and elemental analyses were carried out using X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometry (EDS), respectively. The lattice parameter is found to increase with increasing copper content. A remarkable densification is observed with the addition of Cu ions in the ferrites. The sintered ferrite was characterized for initial permeability, dielectric constant and dielectric loss tangent and ac conductivity measurements. The temperature variation of the initial permeability of these samples was carried out from 30 °C to 200 °C. The dielectric constant, dielectric loss tangent and ac conductivity have been measured in the frequency range of 100 Hz to 1 MHz. Initial permeability and dielectric constant were found to increase and dielectric loss decreased with Cu substitution for Mg, up to x = 0.20. The ferrite powder prepared is suitable for the application in multilayer chip inductor due to its low-temperature sinterability, good magnetic properties and low loss at high frequency.     

CaCu3Ti4O12/NiCuZn铁氧体基磁电复合材料研究

将CCTO(CaCu3Ti4O12)与NiCuZn铁氧体进行复合,系统地研究了组分变化对这种新型磁电复合材料的烧结性能、晶相结构、显微结构和磁电性能的影响。随后,为了实现复合材料的低温烧结以及综合考虑复相陶瓷的磁电性能,选取80%(质量分数,下同)NiCuZn铁氧体/20%CCTO组分,以BBSZ(Bi2O3-H3BO3-SiO2-ZnO)玻璃作为助熔剂,研究了CCTO/NiCuZn铁氧体基复合材料的烧结行为和磁电性能。结果表明,掺杂BBSZ后,900℃下烧结的所有样品的密度均达到了复相陶瓷理论密度的95%,且复相陶瓷的介电常数和磁导率在1～30 MHz范围内均不依赖于频率的变化。在10 MHz的频率下,当BBSZ的含量从0增加到3%时,复相陶瓷磁导率μ从13.2增加到47.9,磁损耗tanδμ从0.022下降到0.017,同时,样品的谐振频率从109Hz左右移动到3.2×108Hz。相应地,复相陶瓷的介电常数ε从9.2增加到16,介电损耗tanδε从0.069下降到0.012。这一优异的整体性能使其有望实际应用。     

Effective dielectric response of polymer composites with ceramic coated silver flakes

High permittivity polymer composites were prepared using Bisphenol A epoxy resin and low loss alumina (Al₂O₃) coated silver (Ag) flakes for embedded passives. The uniformity and thickness of the Al₂O₃ layer were studied using both scanning and transmission electron microscopy (SEM and TEM). SEM was also used to investigate the morphology of the composites and the particle distribution. The dielectric properties of the composites were measured as a function of frequency and temperature. The composites showed a high relative permittivity of 370 with a low loss tangent of 0.07 at 1 MHz and a temperature coefficient of permittivity ~160 ppm/K.     

Preparation, magnetic and microwave absorption properties of La0.5Sr0.5MnO3/La(OH)3 composites

La_0.5Sr_0.5MnO₃/La(OH)₃ composites with different weight ratio of La_0.5Sr_0.5MnO₃ particles and La(OH)₃ nanowires have been prepared by tuning the reaction time under hydrothermal conditions. The structure, morphology and magnetic properties have been investigated. Additionally, by the measurements of the complex permittivity, permeability and microwave absorption properties in the frequency range of 1-12 GHz, the results shown that the weight ratio of La(OH)₃ nanowires has great influence on reflection loss. Excellent absorption property can be obtained when the ratio is 1.4%, which is attributed to the enhanced electromagnetic match as well as the proper dielectric loss and magnetic loss. The enhanced electromagnetic match is originated from the improved frequency dispersion of the complex permittivity and permeability due to the presence of dielectric La(OH)₃ nanowires.     

Low-loss electromagnetic composites for RF and microwave applications

Low-loss electromagnetic composites with high permittivity and permeability will benefit the miniaturization and multifunctional of RF devices. A kind of low-loss dielectric-magnetic ceramic-ceramic composite was developed by hybrid processing technology with the goal of integrating the dielectric properties and magnetic properties. The hybrid processing technology exhibits the advantage of lowered sintering temperatures for the composites while retaining good microstructure and high performance. By introducing elastomer as matrix, a kind of flexible low-loss dielectric-magnetic ceramic-polymer composite was prepared and studied. The obtained flexible dielectric-magnetic ceramic-polymer composite exhibited low loss and good mechanical properties. The results show good effects on lowering the dielectric loss and extending the cut-off magnetic frequency of the electromagnetic composite. Methods for tailoring the properties of the multifunctional composites were proposed and discussed.     

Highly enhancing electromagnetic properties in Fe-Si/MnO-SiO2 soft magnetic composites by improving coating uniformity

Fe-Si/MnO-SiO₂ soft magnetic composites (SMCs) are prepared by sintering ball milled Fe-Si/MnO₂ core–shell structured composites. The correlation between the coating uniformity and electromagnetic properties have been investigated via adjusting ball milling parameters in detail. The results indicate that uniform MnO₂ coating can be transformed into MnO-SiO₂ composite coatings with high insulation due to the high temperature reaction between MnO₂ and Si. Agate ball is more effective than stainless steel ball to improve the uniformity of MnO₂ coating as well as the electromagnetic properties such as significantly higher resistivity, lower core loss and better frequency stability of permeability. Moreover, increasing the ball milling time from 4 h to 24 h can obviously improve the coating uniformity and thus result in the remarkable increase of the resistivity from 2.4 mΩ·cm to 356.9 mΩ·cm. And the core loss and dynamic loss decrease rapidly while the M_s shows a slight decline. When the ball milling time reaches 24 h, the Fe-Si SMCs exhibits superior magnetic properties such as high M_s (181.0 emu/g), very low core loss (361.5 kW/m³ at 100 kHz) and good frequency stability of permeability (65) from 50 Hz to 1000 kHz.     

Studies of the temperature coefficient of capacitance (TCC) of a new electroceramic composite: Pb(Fe0.5Nb0.5)O3 (PFN)–Cr0.75Fe1.25O3(CRFO)

In this paper we did a study of the dielectric properties: capacitance (C), dielectric permittivity(ε), electric modulus(M) and dielectric loss(tangα)) in the radio-frequency(RF) and microwave (MW) frequency range as a function of temperature and the temperature coefficient of capacitance (TCC) of the composites [Pb(Fe_1/2Nb_1/2)O₃(PFN)]_Z–[Cr_YFe_2−YO₃(CRFO)]_100−Z where Z = 0, 10, 50, 90 and 100%. The compounds were prepared by the powder-sintering and the X-ray diffraction (XRD) was used in this study using the Rietveld procedure. The X-ray analysis shows that PFN phase is tetragonal where the CRFO phase belongs to a trigonal structure. The capacitance, dielectric permittivity, electric modulus and loss were studied in the frequency range of 100 Hz to 1GHz and temperature range of 25–100 °C. The values of TCC for all the samples are presenting positive values. The study of the electric modulus (M) as a function of frequency and temperature lead to the measurement of the activation energy (E_ac), which is directed linked to the relaxation process associated to the interfacial polarization effect in the samples. The study of the electrical properties in the RF and MW range of frequencies is important in view of possible applications of these composites as future components in RF and MW circuits.     

Effect of coupling agent on the thermal and dielectric properties of PTFE/Sm2Si2O7 composites

The present study investigates the dielectric and thermal properties of PTFE/Sm₂Si₂O₇ composites. The composites were prepared by powder processing technique followed by hot pressing. The variation of the dielectric properties with filler content (0–0.5 V_f) was studied at 1 MHz and 9 GHz. The filler surface was chemically modified using phenyl trimethoxy silane (PTMS) as a coupling agent. The microstructural study using scanning electron microscopy (SEM) showed that the particles were well dispersed in the matrix when coupled with PTMS. The surface modification led to an improvement in the dielectric properties. The PTFE filled with 0.4 V_f silane treated Sm₂Si₂O₇ composite showed a low dielectric loss of 0.0054 and slightly higher relative permittivity of 3.92 when compared with the untreated composite of the same composition. The experimental values of relative permittivities were compared with the theoretical predictions and the Effective Medium Theory was found to agree well even for higher content of silane treated filler. It was found that the addition of silane coupling agent is very effective in improving the thermal properties of the PTFE/Sm₂Si₂O₇ composites.     

Dielectric,mechanical and thermal properties of polymer/BaTiO3 composites for embedded capacitor

Barium titanate (BaTiO₃) filled polymethylmethacrylate (PMMA) composites were prepared using the simple solution method followed by hot pressing. The content of BaTiO₃ was varied from 0 to 65 vol.%. Scanning electron microscopy showed good dispersion and adhesion of BaTiO₃ with the PMMA matrix. The dielectric constant of the composites increased significantly. There was weak dispersion in the dielectric constant of the composites (up to 45 vol.%) with frequency between 100 Hz and 15 MHz. The dissipation factor of the composites increased from 0.021 for pure PMMA to 0.029 for 45 vol.% composites. However, 65 vol.% composite showed dispersion in dielectric constant with increasing frequency and higher dissipation factor. The Lichtenecker equation agreed well with the experimental data. The microhardness and the glass transition temperature of the composites increased approximately 4.7-fold and 42 °C, respectively, compared to pure PMMA. The CTE of the 65 vol.% composite is close to that of copper.     

Structural and dielectric properties of nanocrystalline Nd<Superscript>3+</Superscript> substituted nickel–zinc ferrites

Ferrite samples with general formula Ni_1−xZn_xNd_yFe_2−yO₄ (x = 0, 0.2, 0.4, 0.6, 0.8 and 1; y = 0.01, 0.02 and 0.03) were synthesized by oxalate co-precipitation technique. The X-ray diffraction study confirms the formation of single-phase cubic spinel structure. The lattice constant of the samples increases with increase in zinc content and obeys Vegard’s law. On Nd³⁺ substitution lattice constant of the samples slightly increases except zinc ferrite. The frequency dependence of the dielectric constant, dielectric loss and AC conductivity of the samples were determined in the frequency range from 20 Hz to 1 MHz at room temperature. The experimental results reveal that the dielectric constant and dielectric loss decreases where as AC electrical conductivity increases with increase in frequency. The dielectric loss increases with increase in zinc content whereas it decreases with increase in Nd³⁺ content. There is no appreciable change in permittivity of the samples with increase in Nd³⁺ content. Permeability of all the samples increases with increase in Nd³⁺ content. Because of lower dielectric loss, Nd³⁺ substituted Ni–Zn ferrites are useful in electronic devices.