共查询到19条相似文献,搜索用时 750 毫秒
1.
通过沉淀法制各了高碳酸根(CO32-)含量的纳米碳酸羟基磷灰石(nanosized carbonated hydroxyapatite,CHA).研究了合成温度、初始原料碳酸氢钠(NaHCO3)和磷酸氢二铵[(NH4)2HPO4]的摩尔比[n(CO32-)/n(PO43-)]和pH值对CO32-替代的影响.用X射线衍射和透射电镜表征CHA粉体的物相组成和形貌.用碳硫元素分析仪和红外光谱研究了CO32-替代的含量和类型.结果表明:随着合成温度的升高或原料中CO32-浓度的减小,CHA晶粒尺寸和长径比增加;合成CHA中的晶相组成和CO32-含量主要由n(CO32-)/n(PO43-)决定;而CO32-的替代类型则主要取决于n(CO32-)/n(PO43-)和pH值.在高pH值或高n(CO32-)/n(PO43-)的合成条件下,能够获得以B型替代为主的CHA. 相似文献
2.
羟基磷灰石和碳酸羟基磷灰石结构和细胞相容性的对比研究 总被引:1,自引:1,他引:0
采用湿化学法制备碳酸羟基磷灰石(CHA)。研究了碳酸根替代对晶体结构和表面能的影响,通过细胞培养实验,比较了羟基磷灰石(HA)和CHA表面的细胞贴附和增殖情况,探讨了表面能与细胞相容性的关系。用X射线衍射和红外光谱分析了晶体结构,用接触角测定仪测量接触角,进而计算样品的表面能。结果表明:湿化学法碱性条件下制备的是以B型替代为主的CHA,其表面能的极性分量高于HA表面能的极性分量,成骨细胞能够在材料表面良好黏附和增殖,具有良好的细胞相容性。 相似文献
3.
4.
5.
在湿CO2气氛中热处理生成碳酸羟基磷灰石的探讨 总被引:2,自引:1,他引:1
将湿化学法合成的不同钙磷摩尔比的粉体,经1 500℃煅烧后,在含水蒸气的CO2中热处理,制备了碳酸羟基磷灰石.应用X射线衍射、红外光谱、差热和热重分析研究了不同热处理温度和不同钙磷摩尔比下产物的化学结构和相组成,讨论了热处理温度和原料钙磷摩尔比对样品相组成的影响.结果表明:所合成的碳酸羟基磷灰石,碳酸根能够进入晶格.热处理温度为800℃时,晶相中有碳酸钙存在,当原料钙磷摩尔比为1.45时,在823~1 000 ℃下热处理结晶相为碳酸羟基磷灰石.当钙磷摩尔比低于或者高于1.45时,存在磷酸三钙、氧化钙、碳酸钙等其它晶相. 相似文献
6.
综述了碳酸根羟基磷灰石的制备方法和国内外研究进展,归纳了计算碳酸根含量和判断替代类型的方法,对该领域的发展前景及今后的研究趋势进行了评述。 相似文献
7.
8.
9.
10.
11.
《Ceramics International》2020,46(17):26784-26789
Effect of sintering temperature on the physical and mechanical properties of synthesized B-type carbonated hydroxyapatite (CHA) over a range of temperature in CO2 atmosphere has been investigated. The B-type CHA in nano size was synthesized at room temperature by using a direct pouring wet chemical precipitation method. The synthesized CHA powders were subsequently consolidated by sintering treatment from 800 to 1100 °C. The sintered CHA samples were evaluated using X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectrometry, X-ray fluorescence (XRF), carbon-hydrogen-nitrogen-sulfur-oxygen (CHNS/O) elemental analyzer, Field emission scanning electron microscopy (FESEM), and Vicker's indentation technique. The results obtained from XRD and FESEM indicated that the synthesized B-type CHA powders were nanometer in size. The crystallinity and crystallite size of the sintered CHA samples were increased due to increasing sintering temperature. The heat treatment between 800 °C and 1000 °C has resulted in coarsening and increased hardness of the sintered CHA samples. However, these properties began to deteriorate when sintering beyond 1100 °C due the formation of calcium oxide. 相似文献
12.
以湿化学法制备了不同氟替代量的氟羟基磷灰石(FHA,Ca10(PO4)6(OH)2-2xF2x,0相似文献
13.
由热压和液相烧结方法制得了具有各种莫来石含量和显微结构的莫来石-堇青石复合体.研究了各种烧结温度、时间、气氛条件下复合体的致密度和显微结构的改善.还研究了复合体弹性模量、断裂韧性、热膨胀系数与组成之间的关系.研究结果表明,复合体的断裂韧性随莫来石含量和杨氏模量线性增加,粗的针状莫来石由于其穿晶断裂模式而有较高的断裂韧性. 相似文献
14.
中温分解钾长石的热力学分析与实验 总被引:15,自引:0,他引:15
综合介绍了利用助剂分解钾长石的研究现状。通过热力学计算预测以碳酸钠、碳酸钾为助剂分解钾长石的分解反应温度在800~890℃之间。分解反应机理的分析表明:随着焙烧温度的升高。钾长石由单一的焙烧分解状态进入分解和烧结同时进行的状态,实验表明:钾长石矿的分解率达98%以上。以碳酸钠、碳酸钾为助剂在820~850℃即可使钾长石分解。 相似文献
15.
16.
纳米碳酸钙的制备及表征 总被引:4,自引:0,他引:4
研究了以氧化钙和二氧化碳为原料,化学法制备纳米碳酸钙的工艺条件、添加剂的影响及形态。结果表明:中间体氢氧化钙的初始浓度、二氧化碳的流量、反应温度、搅拌速度及添加剂等在控制制备纳米碳酸钙颗粒的形状和尺寸中均十分重要。透射电镜观察结果表明:通过控制反应及添加剂,可以得到尺寸规整的链锁形、纺锤形和球形纳米碳酸钙。表面能谱证实产品为高纯的碳酸钙。X射线衍射和电子衍射的结果进一步表明:所制纳米碳酸钙均属方解石型六方晶系,a0=0.498 9 nm,c0=1.706 2 nm;为多晶结构。 相似文献
17.
This article deals with the thermal decomposition behavior of a polysulfone containing 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide versus the initial chloromethylated polysulfone under an inert atmosphere and in air. Thermogravimetric characteristics from thermogravimetry and differential thermogravimetry data revealed important differences related to the employed atmosphere, the types of substituted functional groups, or the degree of substitution. The introduction of the 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide pendent group into polysulfone enhanced the thermal stability of the initial chloromethylated polysulfone in both an inert atmosphere and air. Thermal degradation in nitrogen consisted of one degradation step, whereas thermooxidative degradation in air involved more steps. In air, the degradation mechanism was more complex. The volatile products and solid residues that resulted after pyrolysis in an inert atmosphere and in air were analyzed with Fourier transform infrared and mass spectrometry. Environmental scanning electron microscopy showed that the char residues had different morphologies, which suggested that a more compact structure led to better resistance to heat and oxygen. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci 000: 000–000, 2011 相似文献
18.
实验选取高岭土作为陶瓷基体,以不同含量的鳞片石墨和碳化硅作为导电原料,充分利用炭材料优异的导电、导热性及耐高温性能和陶瓷材料优异的抗氧化性及机械强度,经混合、模压成型和烧结工艺制备出炭/陶复合电热材料。采用XRD和SEM对其物相组成和微观形貌进行分析表征,并对其通电发热性能以及抗氧化性能等进行了测试。研究了石墨以及碳化硅的含量对复合材料电热性能的影响,并对电热机理进行了初步的分析研究。本研究所制备的炭/陶复合材料具有优异的电热性能,在低电压下(10V)即可迅速升温,并在较高温度下保持相对稳定。研制的样品中最高发热温度可达631℃。通过将炭材料和陶瓷材料复合,可有效改善炭材料的抗氧化性,使其氧化失重温度升高200℃左右。 相似文献