固体酸催化棉籽油酯交换制备生物柴油

生物柴油(脂肪酸甲酯)可以由棉籽油与甲醇在酸催化剂的作用下通过酯交换反应制得. 通过硫酸改性氧化钛、氧化锆,并经过高温煅烧得到了相应的固体强酸催化剂TiO2-SO42-, ZrO2-SO42-,并对催化剂活性进行了评价. 实验结果表明,TiO2-SO42-和ZrO2-SO42-与改性前的氧化物相比具有较高的酯交换反应活性. 在230℃、醇油摩尔比12:1及催化剂用量为棉籽油2%(w)的条件下,反应8 h后甲酯的收率达到90%以上. 与固体碱催化剂相比,固体酸催化剂对原料的酸度有更强的适应性. 红外吡啶吸附光谱表明,TiO2-SO42-与ZrO2-SO42-具有较强的L酸和B酸中心.     

Effects of process variables for biodiesel production by transesterification

In this study, biodiesel production from various vegetable oils by transesterification was studied, to determine the optimum conditions. Experiments were carried out by using different kinds of catalysts (sodium hydroxide, potassium hydroxide, barium hydroxide, pyrolitic coke and wood ash) and feedstocks (corn oil, sunflower oil, soybean oil, olive pomace oil and cottonseed oil) at 65 °C and an agitation speed of 1000 rpm. The neutralization step with controlled pH was performed by treatment with phosphoric acid. An experimental design was used to evaluate the effects of the parameters such as types of vegetable oils, kinds of catalysts, reaction time, alcohol/oil volumetric ratio and amount of catalyst, on the methyl ester conversion. Using response surface methodology, a quadratic polynomial equation was obtained by multiple regression analysis. It was found that catalyst concentration was the most effective parameter. Sodium hydroxide and potassium hydroxide exhibited a superior catalytic behavior, whereas pyrolitic coke and wood ash had to be used in excess amount or for prolonged reaction times. Moreover, the properties such as viscosity, density, calorific value, acid value, and refractive index of the biodiesel were measured. The tri‐, di‐, monoacylglycerols and glycerol residuals in the methyl esters produced were also quantified by GC analysis.     

Optimization of transesterification for methyl ester production from chicken fat

In this study, low cost feedstock chicken fat was used to produce methyl ester. After reducing the free fatty acid level of the chicken fat less than 1%, the transesterification reaction was completed with alkaline catalyst. Potassium hydroxide, sodium hydroxide, potassium methoxide and sodium methoxide were used as catalyst and methanol was used as alcohol for transesterification reactions. The effects of catalyst type, reaction temperature and reaction time on the fuel properties of methyl esters were investigated. The produced chicken fat methyl esters were characterized by determining their viscosity, density, pour point, flash point, acid value, methanol content, heat of combustion value, total-free glycerin, mono-di-tri glycerides, copper strip corrosion and ester yield values. The measured fuel properties of the chicken fat methyl ester met EN 14214 and ASTM D6751 biodiesel specifications when using potassium hydroxide and sodium hydroxide catalysts with high ester yield.     

Evaluation of biodiesel obtained from cottonseed oil

Esters from vegetable oils have attracted a great deal of interest as substitutes for petrodiesel to reduce dependence on imported petroleum and provide a fuel with more benign environmental properties. In this work biodiesel was prepared from cottonseed oil by transesterification with methanol, using sodium hydroxide, potassium hydroxide, sodium methoxide and potassium methoxide as catalysts. A series of experiments were conducted in order to evaluate the effects of reaction variables such as methanol/oil molar ratio (3:1–15:1), catalyst concentration (0.25–1.50%), temperature (25–65 °C), and stirring intensity (180–600 rpm) to achieve the maximum yield and quality. The optimized variables of 6:1 methanol/oil molar ratio (mol/mol), 0.75% sodium methoxide concentration (wt.%), 65 °C reaction temperature, 600 rpm agitation speed and 90 min reaction time offered the maximum methyl ester yield (96.9%). The obtained fatty acid methyl esters (FAME) were analyzed by gas chromatography (GC) and ¹H NMR spectroscopy. The fuel properties of cottonseed oil methyl esters (COME), cetane number, kinematic viscosity, oxidative stability, lubricity, cloud point, pour point, cold filter plugging point, flash point, ash content, sulfur content, acid value, copper strip corrosion value, density, higher heating value, methanol content, free and bound glycerol were determined and are discussed in the light of biodiesel standards such as ASTM D6751 and EN 14214.     

Potassium hydroxide catalyst supported on palm shell activated carbon for transesterification of palm oil

In this study, potassium hydroxide catalyst supported on palm shell activated carbon was developed for transesterification of palm oil. The Central Composite Design (CCD) of the Response Surface Methodology (RSM) was employed to investigate the effects of reaction temperature, catalyst loading and methanol to oil molar ratio on the production of biodiesel using activated carbon supported catalyst. The highest yield was obtained at 64.1 °C reaction temperature, 30.3 wt.% catalyst loading and 24:1 methanol to oil molar ratio. The physical and chemical properties of the produced biodiesel met the standard specifications. This study proves that activated carbon supported potassium hydroxide is an effective catalyst for transesterification of palm oil.     

The Optimization of the Production of Methyl Esters from Corn Oil Using Barium Hydroxide as a Heterogeneous Catalyst

In recent years, vegetable oils, as renewable raw materials, became a promising feedstock for chemicals and biodiesel production. The main products derived from oils are esters of fatty acids, especially methyl esters, obtained by their transesterification with methanol, in presence of acid or alkaline catalysts. The use of such catalysts implies the need for washing operations, which leads to environmental pollution. In the present paper, the response surface methodology based on a central composite design, has been developed to optimize the process of transesterification of corn oil. Ba(OH)₂ in presence of diethyl ether was used as catalyst. A quadratic polynomial equation was obtained. It correlates the reaction parameters [methanol/oil molar ratio (x _r), reaction time (x _t) and catalyst concentration (x _c)] with methyl esters yield. Analysis of variance analysis showed that only methanol/oil molar ratio and catalyst concentration have had the most significant influences on the conversion. The maximum methyl esters yield was obtained using the following optimum parameters: methanol/corn oil ratio of 11.32, reaction time of 118 min and catalyst concentration of 3.6 wt%.     

Transesterification of vegetable oil to biodiesel fuel using alkaline catalyst

Biodiesel is gaining more and more importance as an attractive fuel due to the depleting fossil fuel resources. Chemically biodiesel is monoalkyl esters of long chain fatty acids derived from renewable feed stock like vegetable oils and animal fats. It is produced by transesterification in which, oil or fat is reacted with a monohydric alcohol in presence of a catalyst to give the corresponding monoalkyl esters. This article reports experimental data on the production of fatty acid methyl esters from vegetable oils, soybean and cottonseed oils using sodium hydroxide as alkaline catalyst. The variables affecting the yield and characteristics of the biodiesel produced from these vegetable oils were studied. The variables investigated were reaction time (1-3 h), catalyst concentration (0.5-1.5 w/wt%), and oil-to-methanol molar ratio (1:3-1:9). From the obtained results, the best yield percentage was obtained using a methanol/oil molar ratio of 6:1, sodium hydroxide as catalyst (1%) and 60 ± 1 °C temperature for 1 h. The yield of the fatty acid methyl ester (FAME) was determined according to HPLC. The composition of the FAME was determined according to gas chromatography. The biodiesel samples were physicochemically characterized. From the results it was clear that the produced biodiesel fuel was within the recommended standards of biodiesel fuel.     

Transesterification of rapeseed oil in subcritical methanol conditions

In this study, transesterification of rapeseed oil using subcritical methanol conditions was studied. The objective of the work was characterizing the methyl esters for its use as biodiesel in compression ignition motors. The variables affecting the methyl ester yield during the transesterification reaction, such as, the catalyst type and content, reaction temperature and pressure, the presence of hexane as co-solvent, the methanol oil molar ratio and the methanol hexane molar ratio were investigated to optimize the reaction conditions. The evolution of the process was followed by gas chromatography, determining the concentration of the methyl esters at different reaction times. The biodiesel was characterized by its density, viscosity, saponification value, iodine value, acidity index and water content, according to ISO norms. High methyl ester yield and fast reaction rate could be obtained even if the reaction pressure was relatively low, which is quite favorable to the production of biodiesel in industry.     

Biodiesel production from waste frying oil in sub- and supercritical methanol on a zeolite Y solid acid catalyst

Waste frying oil (WFO) is a very important feedstock for obtaining biodiesel at low cost and using WFO in transesterification reactions to produce biodiesel helps eliminate local environmental problems. In this study biodiesel was produced from WFO in sub- and super-critical methanol on a zeolite Y solid acid catalyst. The procedure was optimized using a design of experiments by varying the methanol to WFO molar ratio, the reaction temperature, and the amount of catalyst. Typical biodiesel yields varied from 83 to nearly 100% with methyl esters content ranging from 1.41–1.66 mol·L^-1 and typical dynamic viscosities of 22.1-8.2 cP. Gas chromatography was used to determine the molecular composition of the biodiesel. The reaction products contained over 82 wt-% methyl esters, 4.2 wt-% free acids, 13.5 wt-% monoglycerides, and 0.3 wt-% diglycerides. The transesterification of WFO with methanol around its critical temperature combined with a zeolite Y as an acid catalyst is an efficient approach for the production of biodiesel with acceptable yields.     

Ultrasonic Pretreatment Transesterification for Solid Basic-Catalyzed Synthesis of Fatty Acid Methyl Esters

Generally, ultrasound irradiation is required throughout the reaction for fatty acid methyl esters (FAME, namely, biodiesel) production, which is energy-consuming and difficult to scale-up. In order to improve the industrial application of ultrasonic technology, a systematic study of ultrasonic pretreatment solid basic (Na₂SiO₃)-catalyzed transesterification for FAME production from cottonseed oil was carried out, and the effect of ultrasonic waves on the properties of Na₂SiO₃ catalyst was assessed by X-ray diffraction (XRD), Fourier transform Infrared (FTIR) and scanning electron microscopy (SEM) characterization of fresh and collected catalysts. An ultrasonic frequency of 30 kHz, ultrasonic power of 200 W and ultrasonic pretreatment irradiation time of 30 min was determined to guarantee a satisfactory degree of transesterification. The optimum production was achieved in the reaction system at 45 °C with methanol/cottonseed oil molar ratio 5:1, catalyst dosage 3% and stirring speed 350 rpm resulting in a FAME yield of above 97% after 60 min of reaction under mechanical stirring with the ultrasonic pretreatment process. The new process has a shorter reaction time, a more moderate reaction temperature, a less amount of methanol and catalyst than only the mechanical stirring process without essential damage to activity and the structure of catalyst. These results are of great significance for applying the ultrasonic pretreatment method to produce FAME.     

Biodiesel Production Using Calcined Waste Filter Press Cake from a Sugar Manufacturing Facility as a Highly Economic Catalyst

For the first time, a low cost, high performance and environmentally friendly heterogeneous catalyst derived from waste filter press cake (FPC) from a sugar manufacturing facility was used for the production of biodiesel. This industrial waste was calcined in air at 900 °C for 2 h to convert it into an active CaO‐based catalyst (FPC‐HT). In addition, the calcium oxide nanoparticles (FPC‐NAC) were synthesized by surfactant‐hydration treatment of FPC‐HT. The synthesized catalysts were characterized by XRD, FTIR, SEM, TEM and BET analysis. These calcium oxide catalysts were used for a transesterification reaction between canola oil and methanol to produce biodiesel. The results show that the FPC‐NAC has higher catalytic activity than FPC‐HT under optimized reaction conditions. Therefore, this economic catalyst is able to catalyze the transesterification of canola oil to its methyl esters in 1.5 h with yields above 96 %.     

Biodiesel production from soybean oil using calcined Li–Al layered double hydroxide catalysts

The transesterification of soybean oil to fatty acid methyl esters was studied using a calcined Li–Al layered double hydroxide catalyst. The catalyst exhibited high activity, with near quantitative oil conversion being obtained under mild conditions (reflux temperature of methanol) and short reaction times (≤ 4 h). The influence of relevant parameters (catalyst calcination temperature, methanol to oil mole ratio, catalyst charge and reaction duration) was examined.     

Transesterification of karanja (Pongamia pinnata) oil by solid basic catalysts

The transesterification of karanja oil with methanol was carried out using solid basic catalysts. Alkali metal‐impregnated calcium oxide catalysts, due to their strong basicity, catalyze the transesterification of triacylglycerols. The alkali metal (Li, Na, K)‐doped calcium oxide catalysts were prepared and used for the transesterification of karanja oil containing 0.48–5.75% of free fatty acids (FFA). The reaction conditions, such as catalyst concentration, reaction temperature and molar ratio of methanol/oil, were optimized with the solid basic Li/CaO catalyst. This catalyst, at a concentration of 2 wt‐%, resulted in 94.9 wt‐% of methyl esters in 8 h at a reaction temperature of 65 °C and a 12 : 1 molar ratio of methanol to oil, during methanolysis of karanja oil having 1.45% FFA. The yield of methyl esters decreased from 94.9 to 90.3 wt‐% when the FFA content of karanja oil was increased from 0.48 to 5.75%. The performance of this catalyst was not significantly affected in the presence of a high FFA content up to 5.75%. The catalytic activities of Na/CaO and K/CaO were also studied at the optimized reaction conditions. In these two cases, the reaction initially proceeds slowly, however, leading to similar yields as in the case of Li/CaO after 8 h of reaction time. The purified karanja methyl esters have an acid value of 0.36 mg KOH/g and an ester content of 98.6 wt‐%, which satisfy the American as well as the European specifications for biodiesel in terms of acid value and ester content.     

Polyol-Derived Alkoxide/Hydroxide Base Catalysts I. Production

A metal methoxide is more expensive than a metal hydroxide and dissolves in methanol releasing a methoxide ion without producing water. The methoxide ion has a higher reaction rate making it more preferred for industrial biodiesel production. This study describes the preparation of alkoxide catalysts from metal hydroxides and non-volatile, non-toxic polyols. Heating aqueous solutions of metal hydroxides and different polyols (1,2-propanediol, 1,3-propanediol, glycerol, xylitol and sorbitol) under vacuum yielded polyol-derived alkoxide base catalysts (PDABC). Comparison of the drying process for respective sodium hydroxide-polyol combinations at two mole ratios of sodium hydroxide to polyol showed that drying at 2:1 mole ratio (metal hydroxide to polyol) was more efficient than that of 3:1. Dehydration of alkaline solutions containing three or more hydroxyl groups (glycerol, sorbitol and xylitol) was faster than drying similar solutions of diols. The empirical formula determined confirmed that the resulting powders contained mono-sodium substituted alkoxides at 1:1, 2:1 and 3:1 (sodium hydroxide: polyol) mole ratio. Fatty acid methyl esters were prepared from canola oil and methanol using glycerol sodium alkylate as a catalyst. The conversion yield of oil to methyl ester was greater than 99 %.     

微波强化棉籽油制备生物柴油的研究

利用微波强化以棉籽油和甲醇为原料,KOH为催化剂制备生物柴油。考察醇油摩尔比、催化剂用量、反应时间和微波功率对酯交换反应的影响。结果表明,醇油摩尔比为9∶1,催化剂用量为1.0%,反应时间为3 min,微波功率360 W为最优反应条件。在此反应条件下生物柴油产率可达94%。与传统合成方法相比,该方法可缩短反应时间30~35 min。所得生物柴油主要质量指标达到我国和欧洲(EN14214)生物柴油质量标准,通过红外光谱分析表明,棉籽油生物柴油具有生物柴油所含的官能团。     

疏水改性氧化钙催化制备生物柴油的研究

以溴化苄作为改性剂,采用化学键合方法对市售氧化钙进行表面改性,考察改性氧化钙固体碱催化菜籽油-甲醇酯交换反应制备生物柴油的性能,并在此基础上对该催化体系的耐水性进行考察。通过对反应体系中醇/油摩尔比、催化剂用量和反应时间进行优化,最终得出在醇/油摩尔比为15∶1,催化剂用量为5%以及表面改性剂溴化苄用量为0.2%时,表面改性氧化钙上生物柴油产率在反应3h即可达到99.8%,而未改性氧化钙为催化剂时在相同反应条件下生物柴油产率仅为35.3%。     

亚临界甲醇中麻疯树油制备生物柴油的研究

对麻疯树油在催化剂对甲苯磺酸作用下与亚临界甲醇反应制备脂肪酸甲酯(生物柴油)进行了研究。结果表明在反应温度170℃、醇油摩尔比40:1、催化剂用量占油重的0.75%和反应时间30 m in的条件下,反应产物中脂肪酸甲酯含量可达93%以上。制备的生物柴油,各项指标与柴油相似。主要性能指标,符合ASTMPS121-99(USA)和0#矿物柴油标准。     

棉籽油间歇式酯交换反应动力学的研究

生物柴油(棉籽油甲酯)可以由棉籽油与甲醇在催化剂KOH存在下通过酯交换反应制得。故对棉籽油间歇式酯交换反应动力学进行了研究,并考察了反应温度和催化剂浓度对产物棉籽油甲酯浓度的影响。用液相色谱法分析棉籽油的组成;用气相色谱法分析产物中棉籽油甲酯的含量。由实验数据绘制的动力学曲线得到酯交换反应在开始阶段为准二级反应,以后紧接转为一级反应和零级反应,与文献报导的棕榈油酯交换反应动力学结果一致。由实验数据求出酯交换反应在开始阶段的动力学参数,35℃、45℃时的反应速率常数分别为0.9179Lmol-1min-1和1.049Lmol-1min-1,酯交换反应的活化能为10.88kJmol-1。根据实验结果得到棉籽油酯交换反应的最佳反应温度为45℃,最佳催化剂为1.1%KOH。     

Transesterification Catalysts from Iron Doped Hydrotalcite-like Precursors: Solid Bases for Biodiesel Production

Abstract Described are new solid base catalysts for transesterification of seed oil triglycerides to fatty acid methyl esters, a key step in biodiesel production. These were prepared by substituting Fe3+ ions substitute for a fraction of the Al3+ ions in the Mg/Al layered double hydroxide lattices of hydrotalcites (HTC) and calcining to give porous metal oxides (PMOs). These iron-doped PMOs are much stronger bases than those derived from undoped or Ga3+ doped HTCs and are effective catalysts for the methanol transesterification of triacetin (glycerol triacetate) and of soybean oil. Graphical Abstract New solid base catalysts for transesterification of seed oil triglycerides to fatty acid methyl esters, a key step in biodiesel production, were prepared by substituting Fe³⁺ for Al³⁺ cations in hydrotalcite (HTC) structures and calcining to give porous metal oxides.      

Conversion of waste cooking oil to biodiesel using ferric sulfate and supercritical methanol processes

In this comparative study, conversion of waste cooking oil to methyl esters was carried out using the ferric sulfate and the supercritical methanol processes. A two-step transesterification process was used to remove the high free fatty acid contents in the waste cooking oil (WCO). This process resulted in a feedstock to biodiesel conversion yield of about 85-96% using a ferric sulfate catalyst. In the supercritical methanol transesterification method, the yield of biodiesel was about 50-65% in only 15 min of reaction time. The test results revealed that supercritical process method is probably a promising alternative method to the traditional two-step transesterification process using a ferric sulfate catalyst for waste cooking oil conversion. The important variables affecting the methyl ester yield during the transesterification reaction are the molar ratio of alcohol to oil, the catalyst amount and the reaction temperature. The analysis of oil properties, fuel properties and process parameter optimization for the waste cooking oil conversion are also presented.