Inconel 718高温合金SMAW焊接接头组织及力学性能研究

对Inconel 718镍基高温合金进行焊条电弧焊(SMAW)焊接试验,研究其接头显微组织和力学性能。结果表明,焊接接头由五部分组成,分别为焊缝区、细晶区、不完全再结晶区、粗晶区以及基体;由于焊缝区有大量Laves相的存在,导致焊缝区为焊接热影响最薄弱的区域,拉伸试样断裂位置在焊缝处;显微硬度测试表明焊缝区硬度最低,母材硬度最高。     

Ti60合金板材电子束焊接接头组织性能研究

研究了Ti60合金板材电子束焊接接头的显微组织与力学性能.研究表明,焊接接头熔合区中的显微组织由针状α′相、α相和β相组成,热影响区的显微组织为β相转变组织、针状α′相及部分未溶解的等轴初生α相组成的混合组织.焊接接头硬度呈不均匀分布,焊缝熔合区的硬度最高,热影响区次之,母材区最低.焊接接头的室温和高温拉伸均断裂于母材区,焊接接头处拉伸强度等同于接头处母材区的强度.焊接接头的持久断裂均发生于焊缝区域,接头的持久寿命均100 h.     

TIG焊接热循环对AZ31B镁合金硬度的影响

以AZ31B镁合金为研究对象，采用TIG焊方法进行焊接，考察了焊接热循环对镁合金的硬度的影响。测量、比较、分析了焊缝、热影响区、母材的硬度。结果表明，表面处理过程（研磨、抛光、侵蚀液体及工艺等）对镁合金硬度的影响很大，直接影响到“焊接工艺-硬度”之间关系。与母材相比，由于焊缝的冷却速率高，组织细小，硬度较高。热影响区的组织虽比母材粗大，但硬度与母材相近。焊缝区不同部位的硬度存在一定差异。     

1800 MPa热成形钢与CR340LA低合金高强钢激光焊接性能

采用光纤激光焊接设备对1800 MPa级热成形钢与CR340LA低合金高强钢进行对接激光拼焊,研究了不同激光焊接功率和焊接速度下焊接接头的组织演变规律及热冲压成形性能,并对焊接接头的力学性能和硬度进行了分析。结果表明,3种焊接工艺下激光拼焊原板综合力学性能相差较小,由焊接接头造成的伸长率和抗拉强度的损失均在母材的28.3%和9.1%以内。激光焊接后焊缝区均为粗大、高硬度的马氏体结构;两侧热影响区组织主要为铁素体和马氏体,接头未出现明显的软化区。激光拼焊原板拉伸试样均断裂于CR340LA母材区,距离焊缝12 mm左右,且存在焊缝隆起现象。选取焊接功率和焊接速率分别为4000 W和0.18 m·s?1的焊接试样在高温下进行热冲压成形检测,未出现焊缝开裂,热成形后拼焊板具有良好性能,满足汽车激光拼焊板使用要求,拉伸结果表明,试样断裂位置与未热冲压成形前一致,均位于CR340LA母材区,拉伸过程中,焊缝向高强度母材侧偏移,在弱强度母材侧产生应力集中并缩颈断裂。      

电子束焊喷射成形Al-Zn-Mg-Cu合金的组织性能研究

采用电子束焊接的方法对10 mm厚的喷射成形Al-Zn-Mg-Cu合金板进行了拼焊实验。采用金相显微镜、扫描电镜、室温拉伸实验、显微硬度等方法分析了焊接接头的微观组织,测试了焊接接头的力学性能及显微硬度。结果表明,喷射成形Al-Zn-Mg-Cu合金焊接接头由三个区域(近缝区母材,焊核区,热影响区)组成。焊缝宽为0.3～1.0 mm,焊核区由尺寸约3～8μm的等轴细晶组成,析出相沿晶界分布,晶内析出相较少;热影响区大部分保留了母材的原始组织特征,小部分区域发生了重熔。从焊缝区到母材,显微硬度值逐渐下降,焊缝区硬度值高出母材约35。经T6处理后,焊接接头强度约为母材的82%。     

40CrNiMoA钢同质焊条焊接接头组织和性能研究

分析了焊接电流70A、80A、90A对40CrNiMoA钢焊缝接头组织和力学性能的影响。随着焊接电流的增大,焊缝外观质量较好。随着焊接电流的增大,熔池区温度升高,奥氏体晶粒尺寸增大,导致马氏体组织粗大。焊缝的显微组织为马氏体及少量残余奥氏体。焊缝的硬度远高于母材的硬度,且波动较大。热影响区的硬度从母材向沿焊缝方向逐渐升高。焊接接头纵向应力在焊缝中心为压应力,向外压应力减小。焊接颜色区边界处纵向应力为拉应力,且该点拉应力最大。焊接接头横向应力在焊缝中心为拉应力,向外逐渐增大,焊接颜色区边界处变横向拉应力达到最大。焊接电流和热输入增大,降低了材料的韧性,组织中铁素体增多及焊接残余应力是诱发脆性断裂的原因。焊接电流80A是40CrNiMoA同质焊条平板对接焊接工艺的最佳的焊接电流。     

热处理对40CrNiMoA钢板焊接接头组织及力学性能的影响

本文研究了调质工艺对40CrNiMoA钢板焊接接头显微组织及力学性能的影响。试验结果表明,经 830 - 870 °C +550 - 650 °C 调质处理后,40CrNiMoA钢3 mm板90 A 10 V焊接接头的焊缝区、热影响区、母材区的硬度差异显著减小,形成了回火索氏体组织。调质处理温度越高,焊接接头的焊缝区、热影响区与母材区的组织越 均匀,且组织中的碳化物颗粒尺寸增大。40CrNiMoA钢焊接板经850 Y油淬,600 X.回火后,具有较高的强度(905 MPa)和塑性(13. 5% ),综合力学性能最优。     

HRB400细晶粒热轧带肋钢筋焊接试验

用昆钢开发生产的HRB400细晶粒热轧带肋钢筋作为母材．采用闪光对焊工艺进行焊接。对焊接接头进行力学性能、维氏硬度和金相检验．说明了在焊接热循环作用下,重新奥氏体化后再结晶形成的组织对母材强度有影响。结合焊接接头硬度及金相组织的变化规律。对焊接接头的抗拉强度进行探讨。结果表明．钢筋焊接后焊缝的抗拉强度低于母材．只有将焊接件镦粗。使焊缝有效截面积大于母材截面积的1．1倍．才能保证HRB400细晶粒热轧带肋钢筋焊接接头抗拉强度指标大于该钢种的抗拉强度指标．使焊接接头不发生焊缝断裂。     

TA1中厚板电子束焊接组织性能及接头强化原因分析

采用真空电子束焊对30 mm厚TA1工业纯钛试板开展焊接试验,结合光学金相显微镜(OM)、维氏硬度、拉伸试验及电子背散射衍射(EBSD)对接头进行宏微观组织性能检验,分析电子束焊接过程对TA1材料微观组织与力学性能的影响及接头强化原因.结果 表明:电子束焊接热循环过程使TA1母材至焊缝组织由等轴α向锯齿α转变;焊缝及热影响区的强度、硬度均高于母材;接头性能得到强化与锯齿α及针状α马氏体对硬度的提升作用、焊缝及热影响区内细小的锯齿状α晶粒以及微细孪晶对焊接组织的细化作用有关.     

Al-6.6Zn-1.7Mg-0.26Cu合金挤压材焊接接头的组织与性能

采用光学显微镜、透射电子显微镜、维氏硬度计和拉伸试验机,研究了Al-6.6Zn-1.7Mg-0.26Cu合金挤压材熔化极惰性气体保护焊接接头的显微组织和力学性能。结果表明:焊缝中心区为枝晶,靠近母材侧的焊缝熔合区为柱状晶,母材为等轴晶,但靠近焊缝熔合区的母材晶粒发生了长大。焊接接头的硬度以焊缝为中心呈对称分布,从母材到焊缝中心,硬度先下降后上升再下降。焊缝中心区的硬度最低,为86~105(HV)。焊接接头的抗拉强度为309MPa,屈服强度为237MPa,伸长率为4.75%,挤压材的焊接强度系数为0.76。     

The effect of amount of possession of the trait of hostility on accuracy of perception of hostility in others.

Some theories of personality hold that an individual's perception of others is influenced by his own personality characteristics; more specifically, that a trait of low social value will be projected more into others, and that insight into the possession of these characteristics reduces this distortion. These 2 hypotheses were tested by having a group of college students rate each other (including themselves) on degree of friendliness or hostility. Agreement with group rating about self yielded the insight score. In general, the hypotheses were supported; the "friendly" Ss were most accurate in their perception of others, and insight was positively associated with accurate perception. From Psyc Abstracts 36:04:4HL16M. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Comparison of rates of infection of two methods of emergency ventricular drainage

The rates of infection of two methods of external ventricular drainage in use at Atkinson Morley's Hospital--namely, (a) percutaneous drainage with Rickham reservoirs and (b) tunnelled ventriculostomies--were compared in this retrospective review. Percutaneous drainage of CSF with Rickham reservoirs was associated with a 27% rate of infection as identified by positive microbiological cultures; tunnelled ventriculostomy catheters had a 10% infection rate. The difference in the infection rate between the two methods was statistically significant (P < 0.015). Other variables examined, including the age and sex of the patients and the reasons for ventricular drainage, were not associated with an increased rate of infection. Most infections from either method were caused by a coagulase negative staphylococcus. The average duration of ventricular drainage before identification of positive cultures was 5.7 days for Rickham reservoirs and 6.0 days for ventriculostomies.     

浅析《野草》的版画特征

鲁迅先生一生热爱美术作品,对版画中木刻兴趣尤甚.<野草>作为其"写心之作",亦呈现出一些与木刻版画一致的审美特征:一是具有木刻版画的色彩特征,多对比、多冷色,有阴郁的美感;二是具有木刻版画的力度特征,环境描写、人物刻画处处刀锋毕现,遒劲有力,有一种"力之美".     

四辊破碎机车刀架的改造

针对四辊破碎机车刀架车削中存在的几个问题,详细介绍了电动车刀架的结构和工作原理,建立主要设计参数的数学表达式,并进行适当的分析。改造后,这种电动车刀架运行平稳、可靠、方便、省力,取得了预期的效果。     

转炉炉壳热应力分析

根据实际转炉建立实体模型。以有限元为手段,考虑了炉衬和炉壳材料的物性参数随温度变化的特点和炉衬与炉壳之间膨胀间隙,计算了转炉炉壳在温度载荷和炉衬膨胀压力同时作用下的热应力。所得结果可为转炉炉壳设计提供依据。     

Comparison of the results of surgical and conservative treatment of fractures of the diaphysis of the tibia

In this paper is treated the fundamental problematic of the fracture of the diaphysis of the tibia and the therapeutic results after the conservative and operative treatment are confronted. Among 518 patients with 433 open fractures and 35 with closed fractures of the diaphysis of the tibia, successful treatment of more 2/3 was obtained in the period from 1968 to 1972. Following our casuistics and literature, whose results are similar, we find out that the average total treatment of the osteosynthesis of the fracture of the diaphysis was shortened for 2,5 months depending upon the type and the localisation of the fracture. Apolied methods of the operative and conservative and conservative treatment in relation to the velocity of the medical cure as well as to the extreme anatomical-functional results are analised. We noticed that osteosynthesis, made by the intermedullary nail and the extension of the canals or by a small AO table, by the achieved stability makes conditions of immediate motions and an early rehabilitation. Because of that it gives the best functional results.     

焦炭热性能指标意义浅析

通过对焦炭在高炉内的历程及其变化规律的剖析,阐述焦炭热性能指标的意义,形象地把焦炭在高炉内的损耗分为三部分(M1,M2,M3)。指出M2对焦比及焦炭价格有一定的指导作用。     

Results of treatment of cancer of the cardia

Cancer of the cardia is traditionally discussed with cardiac cancer of the lower portion of the esophagus and upper gastric cancer invading the esophagus, and the specific characteristics of cancer of the cardia have never been clearly defined. We reviewed the outcome of 172 patients with adenocarcinoma of the cardia who had undergone radical surgery between 1949 and 1994 in the Division of Gastrointestinal Surgery of the Cancer Institute Hospital. The centers of the tumors were located within 2 cm above and below the boundary between the esophagus and the stomach, and their longitudinal diameter was less than 8 cm. We divided the patients into an early period (1949-1979; n = 79) and a late period (1980-1994; n = 93), and focused on the historical transition. There were no differences in patient gender or histology between the two periods. However, the late period was associated with fewer cases of esophageal invasion and shorter longitudinal diameter, as the age of the population advanced. The number of advanced cancers such as the localized and infiltrative type had decreased, and early cancer and early clinical stage had become more common, but despite the fact that the number of early cancers had increased, extended dissection, such as thoracic and paraaortic lymph node dissection, was performed more frequently. By clinical stage, the long-term outcome markedly improved in Stage I patient in the late period, and tended to improve in Stage II and III patients. This appears to have been attributable to the prevention of micrometastasis by extended dissection, although the number of early cancers is another major potential cause. There were no differences in the outcome of Stage IV patients between the two periods, and further advances in multimodality therapy must be awaited. The range of resection is basically proximal gastrectomy, and if there are adequate indications, the prognosis is favorable. In view of the status of lymphatic flow and lymph node metastasis, and long-term results, lateroaortic lymph node dissection is important. Since the number of early cancer patients has been increasing, if intraabdominal recurrence is prevented, intrathoracic lymph node dissection will contribute greatly to the outcome of such patients.     

参与式农业基地建设行动方案设计

为了编制实用性强的基地建设行动方案,首先,确定参与式发展的主体,搭建一个"决策框架";其次,针对行动目标,提出不同参与主体,如管理者、农民、消费者等团队与个人的目标及行动内容;最后,工作应向重塑伙伴式合作关系,挖掘农民自我发展潜力,完成三大角色的转换,打造农业基地文化等方向推进.