共查询到20条相似文献,搜索用时 78 毫秒
1.
目的 制备超疏水自清洁的Ti6Al4V合金表面。方法 首先使用飞秒激光在Ti6Al4V合金表面预制备微米级结构,然后将预制备的样品置于1.0 mol/L的氢氧化钠溶液中,在超声水浴状态下进行电化学去合金,获得微纳米复合结构。经表面改性后,得到微纳超疏水钛合金表面。结果 经复合制备的微纳超疏水表面结构由微米级的梯形凸柱阵列,以及通过电化学去合金形成的三维纳米孔洞骨架和沉积的微米或亚微米金属氧化物组成。经过表面改性后,该微纳复合结构表面呈现优异的超疏水性,其接触角可达162.5°,滚动角低至3.4°。自清洁性能测试结果表明,该微纳超疏水钛合金表面展现出优异的低黏附性和自清洁性,1滴水对表面的清洁效率达到99.8%。激光加工参数与静态水接触角之间的关系表明,接触角与扫描间距呈负相关,与能量密度、重复次数呈正相关。结论 飞秒激光结合电化学去合金方法制备的具有微纳结构的钛合金表面呈现出优异的超疏水自清洁性能,通过改变激光加工参数能够有效增大表面的静态水接触角,为后续研究提供了一定参考。 相似文献
2.
目的 研究微/纳米复合超疏水结构的摩擦磨损机制,提高镁合金微摩擦磨损性能。方法 首先采用激光刻蚀获得微米结构,然后表面涂覆SiO2纳米颗粒,获得微/纳米复合结构,最后涂覆低表面能物质获得超疏水表面。用接触角测量仪测量超疏水表面的静态接触角,使用微摩擦磨损实验机分析超疏水表面的摩擦磨损性能,使用扫描电子显微镜观察表面磨痕形貌。结果 当载荷为1 N时,超疏水表面的摩擦系数约为0.04,基体表面约为0.06。随着载荷的增加,超疏水表面的摩擦系数逐渐与基体相近,并逐渐超过基体。随着时间的增加,超疏水表面的摩擦系数呈增加趋势,由0.04逐渐增加到0.08,基体试样没有明显的上升趋势。相同条件下,超疏水表面的磨痕宽度大于基体表面,但磨痕宽度的增大趋势小于基体表面。结论 微/纳米复合结构超疏水表面的摩擦磨损过程不同于光滑基体。超疏水表面的磨损首先发生于微/纳米凸起结构,之后发生于被微/纳米凸起填平的微米凹坑区,然后发生于激光加工热影响区表面,最后发生于镁合金基体。在所受载荷低于1~3 N时,超疏水表面微凸起结构能延缓超疏水表面摩擦磨损的发生,改善耐磨性能。 相似文献
3.
4.
5.
在远程管道运输过程中,固液间摩擦阻力是一个不容忽视的问题,类鲨鱼结构减阻效率低且制备困难。基于荷叶表面仿生思想,构筑微结构制备超疏水表面,减小摩擦阻力。采用飞秒激光刻蚀与电沉积复合工艺,在不锈钢表面构筑框-锥多级结构,经自组装氟硅烷制备超疏水表面,讨论复合工艺参数对微结构形貌及润湿性能的影响,探究框-锥多级结构超疏水表面减阻。结果表明,利用飞秒激光可获得周期性分布的框结构,随着激光功率的增加,微米框结构内部形成不规则沟壑金属堆积物,且关光延时的增长会产生单侧分布微孔结构,损伤基体整体强度;通过电沉积工艺制备亚微米尖锥结构镍镀层,随着电流密度的增加,镀层微结构形态发生变化,形成亚微米尖锥石结构,表面由疏水转变为超疏水。与激光刻蚀10次自组装氟硅烷涂层试样相比,激光刻蚀与电沉积复合工艺自组装氟硅烷涂层的试样表面接触角由138.6°提高到156.7°,对水和30wt.%甘油的减阻率分别由8.17%、14.38%提高到27.74%、23.69%。将激光刻蚀与电沉积相结合,构筑微纳结构经自组装制备超疏水表面,可为降低管道输运中固液间摩擦阻力提供新的技术途径。 相似文献
6.
MB8镁合金表面超疏水复合膜层的制备与表征 总被引:3,自引:0,他引:3
利用微弧氧化技术在镁合金表面制备微米级粗糙结构,采用环氧树脂溶液和纳米二氧化硅分散液对该表面进行涂覆处理,得到二氧化硅纳米颗粒均匀分布的粗糙表面,再利用全氟硅烷改性,制备得到具有超疏水性的复合膜层。采用扫描电镜、X射线衍射仪、接触角测量仪、高速摄影系统评价膜层的形貌结构和润湿性。结果表明,微弧氧化层所具有的微米级结构和纳米二氧化硅颗粒组成的微/纳二元粗糙结构对疏水性的提高具有重要作用;复合膜层表面的接触角随二氧化硅分散液浓度的提高呈现先增加后减小趋势,并最终逐渐稳定在150o左右;在二氧化硅分散液浓度为10.0g/L时,复合表面的接触角最大,可达161o,在此条件下获取的复合表面对不同pH值的液滴均具有超疏水性。同时该表面对水滴呈现低黏附特性。 相似文献
7.
《铸造》2020,(3)
通过优化加工参数,在镁合金表面获得优良的超疏水性能。用激光刻蚀法获得微米结构,结合纳米涂覆技术制备微/纳米复合结构,再结合低表面能物质,制得超疏水表面。系统研究了加工参数对超疏水性能的影响。通过接触角和滚动角测试,评价镁合金表面的超疏水性,并通过扫描电子显微镜对复合结构表面形貌进行分析。采用涂覆法在激光加工后的基体上成功获得了超疏水改性层。加工参数对AZ91D镁合金超疏水性具有重要的影响。当采用点阵形貌,点阵间距50μm,加工电流为15 A,纳米分散液浓度15 g/L时,AZ91D超疏水表面的静态接触角达到最大值161.1°,滑动角为2.109°,超疏水性能达到最佳。 相似文献
8.
9.
10.
《中国有色金属学报》2015,(9)
为研究表面形貌和润湿性对表面摩擦学性能的影响,采用激光加工技术在Ti6Al4V表面加工间距为100μm的网格和点阵微结构,将Si O2纳米粒子涂覆在微结构上构建微纳结构。采用接触角测量仪测量试样的表面接触角和滚动角,采用摩擦磨损实验机(UMT)测试摩擦学性能,采用LEXT OLS4000型3D激光共聚焦显微镜进行表面形貌和磨痕表征。结果表明:在具有微结构的表面涂覆Si O2可制备出具有微纳结构的超疏水Ti6Al4V表面,且网格表面比点阵表面更难以润湿。表面越难以润湿,试样的比磨损率越低,点阵和网格超疏水表面分别将比磨损率降低32.3%和53.8%,且摩擦因数曲线的波动幅度和数值均减小。且具有微纳结构的超疏水表面可显著提高Ti6Al4V的摩擦学性能。 相似文献
11.
Deng-Kui Zhang Guo-Qing Wang Ai-Ping Wu Ji-Guo Shan Yue Zhao Tian-Yi Zhao Dan-Yang Meng Jian-Ling Song Zhong-Ping Zhang 《金属学报(英文版)》2019,32(6):684-694
In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone. 相似文献
12.
After nearly two years'tense construction the first phase of industrialized base of Shenyang Research Institute of Foundry 《中国铸造》2008,5(1):63-64
After nearly two years' tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry (SRIF), located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation. 相似文献
13.
Z. Sun S.L. Zheng Y. Zhang 《金属学报(英文版)》2007,20(3):187-192
Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process. 相似文献
14.
R. González-Martínez 《金属学报(英文版)》2007,20(4):235-240
The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke. 相似文献
15.
R.Z. Wu Z.K. Qu B.D. Sun D. Shu J. Wang 《金属学报(英文版)》2007,20(3):193-198
The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results. 相似文献
16.
B.W. Zhang B.W. Li 《金属学报(英文版)》2007,20(2):129-138
On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes' collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process. 相似文献
17.
An approach based on film buckling under simple uniaxial tensile testing was utilized in this paper to quantitatively estimate the interfacial energy of the nanostructured multilayer films(NMFs) adherent to flexible substrates. The interfacial energies of polyimide-supported NMFs are determined to be *5.0 J/m2 for Cu/Cr, *4.1 J/m2 for Cu/Ta,*2.8 J/m2 for Cu/Mo, *1.1 J/m2 for Cu/Nb, and *1.2 J/m2 for Cu/Zr NMFs. Furthermore, a linear relationship between the adhesion energy and the interfacial shear strength is clearly demonstrated for the Cu-based NMFs, which is highly indicative of the applicability and reliability of the modified models. 相似文献
18.
Chen Wang Bei-Bei Wang Dong Wang Peng Xue Quan-Zhao Wang Bo-Lv Xiao Li-Qing Chen Zong-Yi Ma 《金属学报(英文版)》2019,32(6):677-683
A 17 vol% SiCp/Al–Mg–Si–Cu composite plate with a thickness of 3 mm was successfully friction stir welded(FSWed) at a very high welding speed of 2000 mm/min for the first time. Microstructural observation indicated that the coarsening of the precipitates was greatly inhibited in the heat-affected zone of the FSW joint at high welding speed, due to the significantly reduced peak temperature and duration at high temperature. Therefore, prominent enhancement of the hardness was achieved at the lowest hardness zone of the FSW joint at this high welding speed, which was similar to that of the nugget zone. Furthermore, the ultimate tensile strength of the joint was as high as 369 MPa, which was much higher than that obtained at low welding speed of 100 mm/min(298 MPa). This study provides an effective method to weld aluminum matrix composite with superior quality and high welding efficiency. 相似文献
19.
X.B. Li Y.Q. Xie Y.Z. Nie H.J. Peng H.J. Tao F.X. Yu 《金属学报(英文版)》2007,20(1):27-34
On the basis of energy and shape method for the determination of the valence bond (VB) structures of crystal, the valence bond structure of titanium is redetermined at room temperature and calculated in the whole temperature range of 0-1943K. The outer shell electronic distribution of Ti is e_c~(2.9907) · (s_c~(0.4980) d_c~(2.4927)) ef1.0093 in crystal. The temperature dependences of the VB structures of hcp and bcc phases are the same. The VB structures of hcp and bcc phases monotonically increase or decrease with the increase in temperature, but show discontinuous changes at the phase-transformation temperature 1155K. 相似文献
20.
目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。 相似文献