Study of Atmospheric Pressure Abnormal Glow Discharge

Atmospheric pressure abnormal glow discharge （APAGD） was carried out simply with a transformer of 1 ： 500 driven by a alternating current with a frequency of 50 Hz. Typical stable discharge parameters, namely voltage of 400 V to 850 V and current of 60 mA to 110 mA were measured by oscillograph. Simulation of the discharge process suggested that the stable discharge was supported by the impedance from the secondary coil of the transformer, which offered a negative feedback to prevent the discharge from turning into an arc. An interpretation was given for the oscillogram of the sinuous discharge current and square voltage. Furthermore, the electron temperature and electron density averaged in the discharge channel of APAGD were estimated.     

Deposition of SiOx on Metal Surface with a DBD Plasma Gun at Atmospheric Pressure for Corrosion Prevention

In this study, SiOx films were deposited by a dielectric barrier discharge （DBD） plasma gun at an atmospheric pressure. The relationship of the film structures with plasma powers was investigated by Fourier transform infrared spectroscopy （FTIR）, and scanning electron microscope （SEM）. It was shown that an uniform and cross-linking structure film was formed by the DBD gun. As an application, the SiOx films were deposited on a carbon steel surface for the anti-corrosion purpose. The experiment was carried out in a 0.1 M NaCl solution. It was found that a very good anti-corrosive property was obtained, i.e., the corrosion rate was decreased c.a. 15 times in 5% NaCl solution compared to the non-SiOx coated steel, as detected by the potentiodynamic polarization measurement.     

Characterization of Crystalline Nanoparticles/Nanorods Synthesized by Atmospheric Plasma Enhanced Chemical Vapor Deposition of Perfluorohexane

A mass of nanoparticles/nanorods were formed on a simultaneously deposited gran- ular film by plasma enhanced chemical vapor deposition （PECVD） of perfluorohexane at atmo- spheric pressure without any catalysts or templates. Scanning electron microscopy （SEM） and X-ray photoelectron spectroscopy （XPS） were used to characterize the morphology and the chem- ical compositions of nanoparticles. The average size of particles is about 100 nm and the length of synthesized nanorods is between 1 μm and 2.5/tm. The analyses of transmission electron microscopy （TEM）, high-resolution transmission electron microscopy （HRTEM）, selected area electron diffraction（SAED） and X-ray diffraction （XRD） reveals that the nanoparticles and nanorods are crystalline.     

The Oblique Incident Effects of Electromagnetic Wave in Atmospheric Pressure Plasma Layers

The propagating behaviours, i.e. phase shift, transmissivity, reflectivity and absorp- tivity, of an electromagnetic （EM） wave in a two-dimensional atmospheric pressure plasma layer are described by the numerical solutions of integral-differential Maxwell＇s equations through a generalized finite-difference-time-domain （FDTD） algorithm. These propagating behaviours are found to be strongly affected by five factors： two EM wave characteristics relevant to the oblique incident and three dimensionless factors. The two EM wave factors are the polarization mode （TM mode or TE mode） and its incident angle. The three dimensionless factors are： the ratio of the maximum electron density to the critical density no/nor, the ratio of the plasma layer width to the wave length d/λ, and the ratio of the collision frequency between electrons and neutrals to the incident wave frequency veo/f.     

The Gas Nucleation Process Study of Anatase TiO2 in Atmospheric Non-Thermal Plasma EnhancedChemical Vapor Deposition简

Abstract The gas phase nucleation process of anatase TiO2 in atmospheric non-thermal plasma enhanced chemical vapor deposition is studied. The particles synthesized in the plasma gas phase at different power density were collected outside of the reactor. The structure of the collected particles has been investigated by field scanning electron microscope （FESEM）, X-ray diffraction （XRD）, high resolution transmission electron microscopy （HRTEM） and selected area electron diffraction （SAED）. The analysis shows that uniform crystalline nuclei with average size of several nanometers have been formed in the scale of micro second through this reactive atmo- spheric plasma gas process. The crystallinity of the nanoparticles increases with power density. The high density of crystalline nanonuclei in the plasma gas phase and the low gas temperature are beneficial to the fast deposition of the 3D porous anatase TiO2 film.     

Titanium Alloy Surface Modification by a Spatio-Temporal Atmospheric Pressure DBD Afterglow

The experimental work reported here is devoted to the study of the modifications inflicted on the surface of titanium alloy specimens by an atmospheric pressure dielectric barrier discharge（DBD） reactor in both spatial and temporal afterglow conditions. A commercially available （AcXys Technologies） modified reactor system was used for the surface treatment of the TiA6V4 titanium alloy that is widely used in the aeronautical industry. Wettability surface characterisation and XPS analyses are performed to give a macroscopic and microscopic insight to the surface modifications. Best operating conditions, at constant input energy, were obtained for a duty cycle equal to 10%.     

An Alternative Empirical Formula for Positive Corona Discharge I-V Characteristics in Point-to-Plate Electrode Geometry

Experimental data are presented for a study on the dependence of the I-V character- istics of the corona discharge on pressure and electrode spacing using point-to-plane electrode con- figuration. These experimental data are obtained by a fast, automatic computer data-acquisition system. The data are used to suggest an alternative dimensionally self-consistent empirical equa- tion for the parameterization of the I-V curves. The formula eliminates the need for any prior assumptions concerning the inception voltage, as is customary in this type of work.     

A New Atmospheric Pressure Microwave Plasma Source （APMPS）

An atmospheric pressure microwave plasma source （APMPS） that can generate a large volume of plasma at an atmospheric pressure has been developed at Tsinghua University. This paper presents the design of this APMPS, the theoretical consideration of microwave plasma ignition and the simulation results, including the distributions of the electric field and power density inside the cavity as well as the accuracy of the simulation results. In addition, a method of producing an atmospheric pressure microwave plasma and some relevant observations of the plasma are also provided. It is expected that this research would be useful for further developing atmospheric pressure microwave plasma sources and expanding the scope of their applications.     

Comparison of Sterilizing Effect of Nonequilibrium Atmospheric-Pressure He/O2 and Ar/O2 Plasma Jets

The sterilizing effect of the non-equilibrium atmospheric pressure plasma jet by applying it to the Bacillus subtilis spores is invesigated. A stable glow discharge in argon or helium gas fed with active gas （oxygen）, was generated in the coaxial cylindrical reactor powered by the radio-frequency power supply at atmospheric pressure. The experimental results indicated that the efficiency of killing spores by making use of an Ar/O2 plasma jet was much better than with a He/O2 plasma jet. The decimal reduction value of Ar/O2 and He/O2 plasma jets under the same experimental conditions was 4.5 seconds and 125 seconds, respectively. It was found that there exists an optimum oxygen concentration for a certain input power, at which the sterilization efficiency reaches a maximum value. It is believed that the oxygen radicals are generated most efficiently under this optimum condition.     

Deposition of Polymer Thin Film Using an Atmospheric Pressure Micro-Plasma Driven by Dual-FrequencyExcitation简

Polymer thin film deposition using an atmospheric pressure micro-plasma jet driven by dual-frequency excitations is described in this paper. The discharge process was operated with a mixture of argon （6 slm） and a small amount of acetone （0-2100 ppm）. Plasma composition was measured by optical emission spectroscopy （OES）. In addition to a large number of Ar spectra lines, we observed some spectra of C, CN, CH and C2. Through changing acetone content mixed in argon, we found that the optimum discharge condition for deposition can be characterized by the maximum concentration of carbonaceous species. The deposited film was characterized by scanning electron microscopy （SEM） and X-ray photoelectron spectroscopy （XPS） and Fourier transform infrared （FTIR） spectroscopy. The XPS indicated that the film was mostly composed of C with trace amount of O and N elements. The FTIR suggested different carbon-containing bonds （-CHx, C=O, C=C, C-O-C） presented in the deposited film.     

Atmospheric Pressure Plasma Jet in Organic Solution: Spectra,Degradation Effects of Solution Flow Rate and Initial pH Value

The organic compounds of p-nitrophenol （PNP） solution was treated by the active species generated in a stirred reactor by an atmospheric pressure plasma jet （APPJ）. The emission intensities of hydroxyl （OH）, oxygen （O）, nitric oxide （NO）, hydrogen （H） and molecular （N2） were measured by optical emission spectroscopy （OES）. The relations between the flow rates of the PNP solution and degradation, the degradation effects and initial pH value of the solution were also investigated. Experimental results show that there exist intense emissions of O （777.1 nm）, N（337.1 nm）, OH （306-310 nm） and NO band （200-290 nm） in the region of plasma. Given the treatment time and gas flow rate, the degradation increased as a function of discharge energy and solution flow rate, respectively. The solution flow rate for the most efficient degradation ranged from 1.414 m/s to 1.702 m/s, and contributed very little when it exceeded 2.199 m/s. This indicates the existence of diffusion-controlled reactions at a low solution flow rate and activation- controlled reactions at a high solution flow rate. Moreover, increasing or decreasing the initial pH value of neutral PNP solution （pH=5.95） could improve the degradation efficiency. Treated by APPJ, the PNP solutions with different initial pH values of 5.95, 7.47 and 2.78 turned more acidic in the end, while the neutral solution had the lowest degradation efficiency. This work clearly demonstrates the close coupling of active species, photolysis of ultraviolet, the organic solution flow rate and the initial pH value, and thus is helpful in the study of the mechanism and application of plasma in wastewater treatment.     

Development of Data Acquisition Card Driver for ICRH System on EAST

Presented in this paper is the development of the driver for the data acquisition card with a peripheral component interconnection （PCI） local bus on the ion cyclotron range of frequency heating （1CRH） system. The driver is mainly aimed at the embedded VxWorks system （real-time operating system） which is widely used in various fields of real-time systems. An efficient way is employed to develop this driver, which will advance the real-time control of the ICRH system on the experimental advanced superconductor tokamak （EAST）. The driver is designed using the TORNADO integrated development environment （IDE）, and implemented in C plus language. The details include the hardware configuration, analogue/digital （A/D） and digital/analogue （D/A） conversion, input and output （I/O） operation of the driver to support over five cards. The data acquisition card can be manipulated in a low-level program and meet the requirements of A/D conversion and D/A outputs.     

Simultaneous Oxidization of NOx and SO2 by a New Non-thermal Plasma Reactor Enhanced by Catalyst and Additive

The non-thermal plasma as one of the most promising technologies for removing NOx and SO2 has attrm~ted much attention. In this study, a new plasma reactor combined with catalyst and additive was developed to effectively oxidize and remove NOx and SO2 in the flue gas. The experimental results showed that TiO2 could improve the oxidation efficiency of SO2 in the case of applying plasma while having a negative effect on the oxidation process of NO and NOx. With the addition of NH3, the oxidation rates of NOx, NO and SO2 were slightly increased. However, the effect of adding NH3 on NOx oxidation was negative when the temperature was above 200℃.     

Role of Ion Beam Irradiation and Annealing Effect on the Deposition of AlON Nanolayers by Using Plasma Focus Device

AlON nanolayers are synthesized on Al substrate by the irradiation of energetic nitrogen ions using plasma focusing. Samples are exposed to multiple （5, 10, 15, 20 and 25） focus shots. Ion energy and ion number density range from 80 keV to 1.4 MeV and 5.6×10^19 m^- 3 to 1.3×10^19 m ^-3, respectively. Moreover, the effect of continuous annealing （473 K and 523 K） on an AlN surface layer synthesized with 25 focus shots is also examined. The main features of the X-ray diffraction （XRD） patterns with increasing focus shots are： （i） variation in the crystallinity of AlN along （111）, （200） and （311） planes, （ii） increasing average crystallite size of AlN （111） plane, and （iii） stress relaxation observed in AlN （111） and （200） planes. The crystallinity of AlN surface layer is comparatively better at 473 K annealing temperature. A broadened diffraction peak related to an aluminium oxide phase showing weak crystallinity is observed for 15 focus shots while non-bounded oxides are present in all other deposited layers. Raman and Fourier transform infrared spectroscopy （FTIR） analysis confirm the presence of AlN and Al203 for the surface layer annealed at 473 K temperature. Raman analysis shows that the overlapping of AlN and Al2Oa results in the development of residual stresses. Scanning electron microscope （SEM） results demonstrate that the formation of rounded grains （range from 20 nm to 200 nm） and variations in their microstructures features depend on the increasing number of focus shots. Decomposition of larger clusters into smaller ones is observed.     

Effect of Cold Plasma Treatment on Seed Germination and Growth of Wheat简

This study investigated the effect of cold helium plasma treatment on seed germina- tion, growth and yield of wheat. The effects of different power of cold plasma on the germination of treated wheat seeds were studied. We found that the treatment of 80 W could significantly improve seed germination potential （6.0%） and germination rate （6.7%） compared to the control group. Field experiments were carried out for wheat seeds treated with 80 W cold plasma. Com- pared with the control, plant height （20.3%）, root length （9.0%） and fresh weight （21.8%） were improved significantly at seedling stage. At booting stage, plant height, root length, fresh weight, stem diameter, leaf area and leaf thickness of the treated plant were respectively increased by 21.8%, 11.0%, 7.0%, 9.0%, 13.0% and 25.5%. At the same time, the chlorophyll content （9.8%）, nitrogen （10.0%） and moisture content （10.0%） were higher than those of the control, indicating that cold plasma treatment could promote the growth of wheat. The yield of treated wheat was 7.55 t-ha-1, 5.89% more than that of the control. Therefore, our results show that cold plasma has important application prospects for increasing wheat yield.     

Mechanical Properties of Thermoplastic Polyurethanes Laminated Glass Treated by Acid Etching Combined with Cold Plasma

To overcome the problem of interlaminar delamination of thermoplastic polyurethane laminated glass, silicate glass was etched with hydrofluoric acid and thermoplastic polyurethane was then treated with cold plasma. Compared with the untreated samples, the interlaminar shear strength of acid etching samples, cold plasma-treated samples and acid etching combined with cold plasma-treated samples increased by 97%, 84% and 341%, respectively. Acid etching combined with cold plasma-treated samples exhibited a higher flexural strength and strain as compared with the untreated samples. The impact energy of acid etching samples, cold plasmatreated samples and acid etching combined with cold plasma-treated samples increased by 8.7%, 8.1% and 11.6%, respectively, in comparison with the untreated samples. FT-IR analysis showed that a large number of -C-O, CO N and CO O C groups appeared on the surface of cold plasma-treated thermoplastic polyurethane, which resulted in the formation of hydrogen bonds. SEM results showed that some pittings formed on the surface of the silicate glass treated by acid etching, which resulted in the formation of a three-dimensional interface structure between tile silicate glass and polyurethane. Hydrogen bonds combined with the three-dimensional interface between silicate glass and polyurethanes co-improved the mechanical properties of thermoplastic polyurethanes laminated glass.     

Density and temperature of fermions and bosons from quantum fluctuations

A novel method to determine the density and temperature of a system constituted by fermions and/or bosons is proposed based on quantum fluctuations. For fermions system, the results in the limit where the reached temperature T is small and where there is no constraint for the reached temperature T compared to the Fermi energy ~f at a given density p are given, respectively. Quadrupole and multiplicity fluctuation relations are derived in terms of T/6f. We compared the two set results in the limit when Tis much smaller compared to Fermi energy Cf and they are consistent, as expected. The classical limit is also obtained for high temperatures and low densities. For bosons system, quadrupole and multiplicity fluctuations using Landau＇s theory of fluctuations near the critical point for a Bose-Einstein condensate （BEC） at a given density p are derived. As an example, we apply our approach to heavy ion collisions using the Constrained Molecular Dynamics model （CoMD） which includes the fermionic statistics. The multiplicity fluctuation quenching for fermions is found in the model and confirmed by experimental data. To reproduce the available experimental data better, we propose a modification of the collision term in the approach to include the possibility of ct-a collisions. The relevant Bose-Einstein factor in the collision term is properly taken into account. This approach increases the yields of bosons relative to fermions closer to data. Boson fluctuations become larger than one as expected.     

Reaction mechanisms in massive nuclei collisions and perspectives for synthesis of heavier superheavy elements

We discuss a hardship in synthesis of heaviest super heavy elements in massive nuclei reactions due to the hindrance to complete fusion of reacting nuclei caused on the onset of quasifission process which strongly competes with complete fusion and due to the strong increase of fission yields along the de-excitation cascade of the compound nucleus in comparison with the evaporation residue formation. The hindrance to formation of compound nucleus and evaporation residue is determined by the characteristic of the entrance channel.     

Second Discharge Characteristics of Aluminum Wire Electrical Explosion Under Various Argon Pressures

Electrical wire explosion is a promising method for the preparation of metal nanopowder, but the properties of metal nanopowder are affected by the second discharge process of electrical wire explosion. The second discharge characteristics of aluminum wire electrical ex- plosion under variant argon pressures were studied in a RLC discharge circuit. The results show that the curve of the second discharge voltages versus the pressure presents a U-shape. To clarify the roles of aluminum vapor and argon in the process of the second discharge, a spectrograph and a high speed framing camera were used to study the radiation spectrum and spatial distribution of the electrical explosion plasma. It is observed that argon participates in the second discharge process under low pressure. A discharge channel develops along the surface of the aluminum vapor. Under higher pressure, a second discharge takes place in the aluminum vapor and the discharge channel is inside the aluminum vapor.