高强度船板钢中针状铁素体的原位观察

采用高温共聚焦显微镜对高强度船板钢中针状铁素体进行原位观察,并利用金相显微镜分析原位观察后其组织形态。结果表明,随着保温时间的增加,平均奥氏体晶粒尺寸增大。保温时间为900 s时获得的奥氏体尺寸更有利于针状铁素体的形核。随着保温时间的延长,铁素体开始相变的温度先减小后增加,而铁素体的相变结束温度逐渐减小。     

Optimization of strength and toughness in two high-strength stainless steels

It has been found possible to increase the strength and toughness of two high-strength stainless steels, AFC 77 and AFC 260, by austenitizing at temperatures that are in the range where both austenite and δ ferrite are stable. The δ ferrite is then removed by isothermal transformation in the range 1800° to 2000°F. This technique results in a greater solution of carbides and intermetallic particles and consequently in a greater amount of retained austenite than is possible at austenitizing temperatures below the δ-ferrite range. In addition, the technique permits optimum mechanical properties to be obtained over a wider compositional range.     

微合金化热轧TRIP钢的工艺模拟

 借助MMS-300热模拟试验机研究了控轧温度区间、终冷温度、贝氏体区等温处理以及冷却路径对微合金化热轧TRIP钢组织演变规律的影响。结果表明,随着控轧温度区间“下调”,组织中的铁素体晶粒越来越细小,铁素体量逐渐增加,残余奥氏体量则先增加后减少。终冷温度升高时,组织中的残余奥氏体量也呈现出先增加后减少的变化趋势,而贝氏体温度范围等温时间的延长使残余奥氏体量增加。相对于“缓冷+快冷”,轧后采用“快冷+缓冷+超快冷”冷却路径更有助于铁素体晶粒的细化和奥氏体的残留。在“快冷+缓冷+超快冷”冷却路径下,当控轧温度区间为900~840℃,缓冷温度范围为710~680℃,贝氏体等温处理制度为450℃×5min时,组织中的残余奥氏体量达到最高值113%。     

Influence of Copper Addition and Temperature on the Kinetics of Austempering in Ductile Iron

Austempered ductile iron (ADI) is a material that exhibits excellent mechanical properties because of its special microstructure, combining ferrite and austenite supersaturated with carbon. Two ADI alloys, Fe-3.5 pct C-2.5 pct Si and Fe-3.6 pct C-2.7 pct Si-0.7 pct Cu, austempered for various times at 623 K (350 °C) and 673 K (400 °C) followed by water quenching, were investigated. The first ferrite needles nucleate mainly at the graphite/austenite interface. The austenite and ferrite weight fractions increase with the austempering time until stabilization is reached. The increase in the lattice parameter of the austenite during austempering corresponds to an increase of carbon content in the austenite. The increase in the ferrite weight fraction is associated with a decrease in microhardness. As the austempering temperature increases, the ferrite weight fraction decreases, the high carbon austenite weight fraction increases, but the carbon content in the latter decreases. Copper addition increases the high carbon austenite weight fraction. The results are discussed based on the phases composing the Fe-2Si-C system.     

Hot plastic deformation of 08X21H5T steel

The nonuniformity of hot plastic deformation of 08X21H5T steel is studied. Tensile tests are conducted in the vacuum chamber of the IMASH-20-75 Ala-Too machine. The samples are attached to a clamp in the chamber by means of straps. A junction of a platinorhodium–platinum thermocouple is soldered to the side surface of the sample. Air is pumped out of the chamber to a residual pressure of 5.0 × 10^–5 mm Hg (6.7 × 10^–3 Pa). The sample is heated to 800–1200°C by means of industrial-frequency current. The precision of temperature maintenance is ±5°C. The deformation of the austenite and ferrite phases is investigated as a function of the overall deformation of the steel and the temperature. The influence of these factors on the slip rate of the austenite and ferrite phases along the grain boundaries is also considered. The hot-microhardness ratio of the austenite and δ ferrite in 08X21H5T steel is investigated as a function of the temperature.     

850级钢熔化焊焊缝的组织特征

利用金相显微镜、扫描电子显微镜及附带EDS系统和透射电子显微镜研究850 MPa级焊缝金属的微观组织,并通过分析焊缝金属凝固和相变过程,研究组织形成机制。发现原δ铁素体柱状晶晶界附近的锰和镍含量高于其心部含量。原δ铁素体柱状晶晶界附近组织由平行板条马氏体组成,板条宽度约为300 nm,原δ铁素体柱状晶心部组织由"交织状"板条马氏体组成,板条宽度约为400 nm。分析认为造成原δ铁素体柱状晶晶界附近和心部组织差异的重要原因是锰和镍的偏析,而焊缝金属良好的冲击韧性是因为存在30%"交织状"马氏体和一定量残余奥氏体。     

冷轧TRIP590钢带的成分优化

 化学成分和热处理工艺是影响TRIP钢力学性能的关键因素。通过热模拟试验方法研究了不同成分试验钢在临界区退火过程中的微观组织变化规律。结果表明：随着两相区退火温度的升高,铁素体平均晶粒尺寸逐渐减小,铁素体体积分数随着加热温度的升高而降低;残余奥氏体量和其中的C质量分数先随着退火温度的升高而降低,达到一个低谷以后,再随退火温度的升高而升高;在相同的退火温度下,随着Nb的加入,多边形铁素体晶粒尺寸细化,铁素体体积分数逐渐减少;既加Nb又高Si的试验钢钢中残奥数量最多,不加Nb的试验钢中残奥数量最少。TRIP钢试制结果表明,钢带组织类型为典型的TRIP钢组织,多边形铁素体平均晶粒尺寸约8μm,体积分数67%,残余奥氏体体积分数为5.58%,残余奥氏体中C质量分数为1.34%,同时,力学性能也完全满足TRIP590的性能要求。     

Weldability of corrosion-resistant high-nitrogen austenitic Kh22AG16N8M-type steels

The influence of thermal treatment on the structures and mechanical properties of welds of corrosion-resistant high-nitrogen austenitic 05Kh22AG16N8M-type steels is studied. In these steels, austenite is found to be highly resistant to discontinuous precipitation and the formation of σ phase and δ ferrite upon cooling regardless of the temperature of heating for quenching (from 900 to 1250°C) and the cooling conditions (water, air, furnace). Welding of these steels can produce high-strength welds with an enhanced impact toughness.     

Phase transformations in a corrosion-resistant high-chromium nitrogen-bearing steel

The structure, phase composition, and mechanical properties of an austenitic corrosion-resistant high-chromium nitrogen-bearing (～0.5% N) steel are studied in the as-cast state and after homogenizing heat treatment (HT) followed by quenching. The main structural constituents of the as-cast steel are austenite and the σ phase (12%), which forms as an interdendritic metal during solidification, and δ ferrite and M ₂₃C₆-type chromium carbides are absent. Homogenizing HT at 1100–1200°C leads to the σ → γ transformation through the stage of the formation of intermediate δ ferrite via the restructuring of the tetragonal into the bcc lattice. Upon long-term homogenizing HT, the chromium concentration in ferrite decreases due to diffusion chromium redistribution and the δ → γ transformation takes place. The austenite in both the as-cast steel and the steel subjected to homogenizing HT followed by water quenching contains numerous (Cr, V)N nanoparticles. The twofold yield strength of this steel (～400 MPa) as compared to nitrogen-free 18Cr-10Ni-type steels can be explained by not only the solid-solution hardening of austenite by nitrogen but also by precipitation hardening.     

含氮不锈钢凝固模式及显微组织研究

研究了四种不同N含量的18Mn18Cr N不锈钢的凝固模式、显微组织和元素分布.结果表明:N含量影响18Mn18Cr N合金系的凝固模式和显微组织.氮的质量分数由0.07%增加至0.72%时,实验钢的凝固模式由F模式转变为A模式,显微组织由铁素体和奥氏体魏氏两相组织转变为铁素体和奥氏体两相组织以及单相奥氏体组织.N含量影响奥氏体相形貌,随N含量增加,奥氏体由板条状、针状转变为枝晶间和等轴状.枝晶间和等轴状奥氏体晶粒中存在褶皱形貌,且随着氮含量增加,褶皱数量增多.褶皱的产生与凝固过程中奥氏体相内部Fe、Mn、Cr元素的偏析有关,且该凝固偏析被保留至室温组织中.      

Influence of intercritical annealing temperature on microstructure and mechanical properties of medium Mn TRIP steel

The transformation, microstructure and mechanical properties of the 0. 2C- 5Mn TRIP steel after intercritical annealing were investigated using dilatometer, scanning electronic microscopy (SEM), transmission electron microscopy(TEM), X- ray diffraction (XRD), and tensile testing machine. The phase transformation thermodynamics of the investigated steel after intercritical annealing was calculated by Factsage software and the characteristics of the transformation were discussed. The results show that the reversed austenite content increases with the increasing of the intercritical annealing temperature, the carbon content in reversed austenite firstly increases and then decreases, manganese content in reversed austenite decreases, which results in the decreasing of the thermal stability of reversed austenite. When the intercritical annealing temperature is 700??, an obvious martensitic transformation occurs during the cooling process. With the increasing of intercritical annealing temperature, cementite is gradually dissolved, but it cannot be completely dissolved due to the short transformation time. When the intercritical annealing temperature is 600-675??, the microstructure after intercritical annealing consists of ferrite, cementite and retained austenite. When the intercritical annealing temperature is 700??, the microstructure after intercritical annealing consists of ferrite, retained austenite, martensite and a small amount of undissolved cementite. The engineering stress and strain curves of the investigated steel are significantly changed with increasing intercritical annealing temperature. At the same time, the optimal mechanical properties with tensile strength of 1138MPa and total elongation of 23% can be obtained after annealed at 675?? for 3min.     

Nb的析出对变形诱导铁素体相变的影响

通过Gleeble2000热模拟实验机，研究了X65管线钢中Nb在变形奥氏体中的析出状态对变形诱导铁素体相变（DIFT）的影响。试验结果表明，在奥氏体临界区变形时，第一道次变形后，随变形后等温时间延长，诱导铁素体量变化不大。等温时间达120S时，变形奥氏体仍未发生再结晶。在道次间随时间延长，Nb的析出量增加，第二道次变形后诱导的铁素体也显著增加。微合金元素Nb通过碳氮化物的析出作用促进变形诱导铁素体相变。     

Austenite Recrystallization and Controlled Rolling of Low Carbon Steels

The dynamic recrystallization and static recrystallization in a low carbon steel were investigated through single-pass and double-pass experiments. The results indicate that as the deformation temperature increases and the strain rate decreases, the shape of the stress-strain curve is changed from dynamic recovery shape to dynamic recrystallization shape. The austenite could not recrystallize within a few seconds after deformation at temperature below 900 ℃. According to the change in microstructure during deformation, the controlled rolling of low carbon steel can be divided into four stages： dynamic recrystallization, dynamic recovery, strain-induced ferrite transformation, and rolling in two-phase region. According to the microstructure after deformation, the controlled rolling of low carbon steel can be divided into five regions： non-recrystallized austenite, partly-recrystallized austenite, fully-recrystallized austenite, austenite to ferrite transformation, and dual phase.     

Study on transformation behavior of hot- rolled microalloyed TRIP steel

Effects of deformation mode, deformation temperature, deformation rate, cooling rate and slow- cooling stop temperature on the transformation behavior of hot- rolled microalloyed TRIP steel were studied by means of MMS- 300 thermomechanical simulator. The results show that for the samples subjected to the single or double pass deformation, ferrite transformation area is expanded, pearlite transformation area appears, and martensite transformation area disappears in the continuous cooling transformation diagrams. Transformation temperatures of Ar3, Bs and Bf decrease, diffusional transformation is prevented and intermediate temperature transformation is promoted with the increase of deformation temperature or cooling rate. When deformation temperature is 850??, transformation temperatures of Ar3, Bs and Bf increase, the amount of ferrite also increases, and the amount of bainite decreases in the microstructure with the increase of deformation rate. With the decrease of slow- cooling stop temperature, ferrite amount increases, ferrite grains grow and retained austenite amount first increases and then decreases.     

等温压缩对高强度汽车钢WHT1300HF的马氏体相变及微观组织的影响

通过等温形变研究了形变参数(形变温度、形变速率、形变量)对高强度汽车钢WHT1300HF的微观组织转变和形貌的影响规律。研究结果表明:增加奥氏体等温形变量,有利于铁素体的缺陷形核,促进了形变奥氏体向铁素体转变;奥氏体的形变强化导致马氏体相变阻力增大,马氏体相变开始温度(Ms)下降,细小晶粒数量和小角度晶界数量增多;增加奥氏体等温形变(40%)速率能同时促进马氏体和铁素体相变,但马氏体体积分数和小角度晶界数量减少,细小晶粒数量略有提高;降低等温形变温度加剧奥氏体的形变强化,导致Ms温度下降,马氏体体积分数、小角度晶界比例减少,细小晶粒数量增多,铁素体含量明显增加。     

Effect of Austempering on the Structures and Performances of Cast High Carbon Si‐Mn Steel

The effects of austempering on the microstructures and mechanical performances of cast high carbon silicon and manganese steel (HCSMS) containing 1.0 wt.%C‐2.5 wt.%Si‐1.5 wt.%Mn‐1.0 wt.%Cr‐0.5 wt.%Cu were studied. The test results show a plate‐like morphology of bainitic ferrite. Each plate of the ferrite is surrounded by a thin layer of retained austenite when the austempering temperature is low, whereas large blocky areas of retained austenite are observed when the temperature is higher. The amount of retained austenite in the bainitic structure increases with increasing isothermal quenching temperature. Austempering results in a significant improvement in the mechanical performances of HCSMS. The main effect of the austempering temperature on the mechanical performances is that hardness and strength are decreased and elongation, impact toughness and fracture toughness are increased with increasing temperature. Cast HCSMS has excellent comprehensive mechanical performance when austenized at 593K.     

冷轧中锰钢退火过程中硬度及组织的演化

 利用EBSD技术研究了冷轧中锰钢在退火过程中的组织演化规律,从而揭示了其硬度变化的原因。研究结果表明:冷轧中锰钢在650℃退火,获得了0.3~0.6μm等轴状奥氏体和铁素体的超细晶组织,且随着退火时间的延长组织结构没有发生明显粗化;在550~650℃退火,随着温度的升高,奥氏体含量不断增加;在700℃退火时,奥氏体稳定性降低,出炉空冷过程中发生了马氏体转变,硬度升高;逆转变奥氏体相的稳定性主要受其碳含量控制,碳含量越高越容易获得大量稳定的逆转变奥氏体。     

水电行业用超级马氏体不锈钢合金化特点

阐述了水电行业用超级马氏体不锈钢的性能要求以及此类材料成分设计、合金化特点和基本原则。重点分析了合金成分设计对于超级马氏体不锈钢中逆转变奥氏体和6铁素体含量及分布的影响。     

Effects of austenite grain size and cooling rate on Widmanstätten ferrite formation in low-alloy steels

Deformation dilatometry is used to simulate the hot rolling of 0.20 pct C-1.10 pct Mn steels over a product thickness range of 6 to 170 mm. In addition to a base steel, steels with additions of 0.02 pct Ti, 0.06 pct V, or 0.02 pct Nb are included in the study. The transformation behavior of each steel is explored for three different austenite grain sizes, nominally 30, 55, and 100 μm. In general, the volume fraction of Widmanst?tten ferrite increases in all four steels with increasing austenite grain size and cooling rate, with austenite grain size having the more significant effect. The Nb steel has the lowest transformation temperature range and the greatest propensity for Widmanst?tten ferrite formation, while the amount of Widmanst?tten ferrite is minimized in the Ti steel (as a result of intragranular nucleation of polygonal ferrite on coarse TiN particles). The data emphasize the importance of a refined austenite grain size in minimizing the formation of a coarse Widmanst?tten structure. With a sufficiently fine prior austenite grain size (e.g., ≤30 μm), significant amounts of Widmanst?tten structure can be avoided, even in a Nb-alloyed steel.     

High temperature plastic-flow behavior of mixtures of austenite,cementite, ferrite,and pearlite in plain-carbon steels

The plastic-flow behavior of ferrite + pearlite, pearlite + cementite, and austenite + cementite mixtures in plain carbon steels has been examined over the temperature range 500 to 1050 °C, strain-rate range 6 x l0⁻⁶ to 2 x l0⁻² s⁻¹, and carbon range 0.005C to 1.89C. Up to the eutectoid temperature the strength of the ferrite + pearlite mixture more than doubles as the carbon content increases from 0.005C to 0.7C, so that whereas in low-carbon steels the ferrite is weaker than the higher temperature austenite phase, in eutectoid steels the fully pearlitic structure is stronger than the fully austenitic structure. Manganese and silicon strengthen ferrite more effectively than they do austenite. A 0.17 pct phosphorus addition strengthens the ferrite + pearlite mixture across the range of microstructures from fully ferritic to fully pearlitic. Beyond the eutectoid composition, the amount of proeutectoid cementite does not significantly affect the strength of the pearlite, but above the eutectoid temperature it appreciably strengthens the austenite and cementite mixture at the strain rate of 2 X 10^-2 s^-1.