Modification of polyamide 6 with hycar ATBN

The preparation of block copolymers from 6-caprolactam and a liquid amine terminated butadiene-acrylonitrile copolymer Hycar ATBN 1300X21 having higher notched impact strength than ordinary poly(6-caprolactam) was studied. In the polymerization of 6-caprolactam initiated by an adduct of phosphoric acid with 6-caprolactam the influence of initiator concentration (0– 50 mol-%) and Hycar ATBN 1300X21 concentration (0–5 wt.-%) in the polymerization charge, of polymerization time (4 – 72 h) and of temperature (200–280°C) on the 6-caprolactam conversion and on the properties of the copolymers formed were followed. Notched impact strength of the block copolymers prepared under optimized conditions was as high as 13.5 kJ·m^?2.     

Polymerization of lactams, 87. Block copolymers of poly(ϵ-caprolactam) and polybutadiene prepared by anionic polymerization. Part I: Preparation and properties

The effect of the polymerization conditions on the properties of poly(?-caprolactam)-polybutadiene block copolymers prepared by polymerization casting through anionic polymerization of ?-caprolactam initiated with potassium salt of ?-caprolactam in the presence of α,ω-dihydroxy-polybutadiene and isocyanates or their blocked derivatives as functionalizing agents was investigated. The influence of the content of telechelic polybutadiene, its molecular weight, type of diisocyanate, and polymerization temperature on the fundamental mechanical properties of the prepared materials and on the polymerization rate was evaluated.     

Powdered poly(ethylene terephthalate)

The influence of the conditions of preparation on the properties of powdered poly(ethylene terephthalate) was followed from the point of view of its specific surface. The powdered poly(ethylene terephthalate) prepared by reprecipitation from the melt of 6-caprolactam has a porous and structured surface, and consequently, also a large specific surface in comparison with the powedered poly(ethylene terephthalate) prepared by mechanical milling. The specific surface value is influenced by the cooling rate of the initial homogeneous melt of poly(ethylene terephthalate)-6-caprolactam, by the concentration of poly(ethylene terephthalate) in this melt and by its molecular weight, by the water temperature at the extraction of 6-caprolactam from the tough mixed melt, by the drying temperature of the powdered poly(ethylene terephthalate), and by the content of residual 6-caprolactam in the powdered product. In the examined area, the specific surface value of the powdered poly(ethylene terephthalate) prepared by reprecipitation from the melt of 6-caprolactam ranged from 10 to 110 m²·g^?1.     

Synthesis and characteristics of the composites based on poly(caproamide) and multiwalled carbon nanotubes

Polycaproamide composites are synthesized by the anionic activated bulk polymerization of ?-caprolactam in the presence of 0.1–5.0 wt % of multiwalled carbon nanotubes and using low-molecularmass monofunctional (N-acetyl-?-caprolactam) and macromolecular polyfunctional (aromatic polyimides) activating agents. The effect of nanotubes on the polymerization of ?-caprolactam is studied, and this effect is shown to become more pronounced as the concentration of nanotubes is increased. The effect of nanotubes on the microstructure, phase composition, water sorption, thermophysical, mechanical, and friction characteristics of poly(caproamide) is analyzed.     

Polymerization of lactams, 95 Preparation of polyesteramides by the anionic polymerization of ε-caprolactam in the presence of poly(ε-caprolactone)

Preparation of polyesteramides-poly[(ε-caprolactam)-co-(ε-caprolactone)]s by anionic polymerization of ε-caprolactam in the presence of poly(ε-caprolactone) at 150 °C was studied in this paper. ε-Caprolactam magnesium bromide was used as an initiator of polymerization and polymeric materials containing 5-25 wt% ε-caprolactone units were obtained. Thermal methods (DSC and DMA) were employed for characterization of poly[(ε-caprolactam)-co-(ε-caprolactone)]s and their mechanical properties were also evaluated. By introducing the activator with N-acyllactam structure, the polymerization rate increased and it was possible to carry out the polymerization at 110 °C. Mechanical properties of polyesteramides were influenced by both the content of ε-caprolactone units incorporated into copolymer and polymerization temperature. The mechanism of incorporation of poly(ε-caprolactone) is discussed. The results show that it is not possible to restrict exchange transacylation reactions, progressing in the course of polymerization, by kinetic tools.     

Structure of poly(ε-caprolactam) obtained in anionic bulk polymerization

The nascent structures of poly(ε-caprolactam) (N6), obtained during anionic polymerization in bulk in the presence of different additives, were investigated. The experimental data show that both the type and the quantity of activator influence significantly the process of polymerization as well as the chemical and the physical structures of N6. By means of WAXD, DSC, IR, light and transmission microscopy (TEM), and electron microdiffraction (ED) the changes in the morphological and the crystal structure were followed. The observed alterations in the physical structures of N6 samples are explained on the base of changes in the chemical structure and mobility of the polymer chains. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(dimethylamino ethyl methacrylate)–poly(ethylene oxide)–poly(dimethylamino ethyl methacrylate) triblock copolymers

Novel, monodispersed, and well‐defined ABA triblock copolymers [poly(dimethylamino ethyl methacrylate)–poly(ethylene oxide)–poly(dimethylamino ethyl methacrylate)] were synthesized by oxyanionic polymerization with potassium tert‐butanoxide as the initiator. Gel permeation chromatography and ¹H‐NMR analysis showed that the obtained products were the desired copolymers with molecular weights close to calculated values. Because the poly(dimethylamino ethyl methacrylate) block was pH‐ and temperature‐sensitive, the aqueous solution behavior of the polymers was investigated with ¹H‐NMR and dynamic light scattering techniques at different pH values and at different temperatures. The micelle morphology was determined with transmission electron microscopy. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis,structure and behavior of new polycaprolactam copolymers based on poly (ethylene oxide)–poly (propylene oxide)–poly (ethylene oxide) macroactivators derived from Pluronic block copolymers

Novel series of poly (CL–co–Pluronic) polymers were successfully synthesized in situ by ring-opening polymerization (ROP) of ε-caprolactam (ε-CL). The copolymerization was activated by new type macroactivators (MAs) based on hydroxyl-terminated poly (ethylene oxide)-poly (propylene oxide)-poly (ethylene oxide) [PEO-PPO-PEO] triblock copolymers, known under the trade name Pluronic^®. Toluene-2,4-diisocyanate (TDI) was used to obtain the isocyanate-terminated Pluronic prepolymers. The corresponding MAs were synthesized in situ with an N-carbamoyllactam structure. As an initiator of the copolymerization processes was used sodium lactamate (NaCL). To confirm the influence over the copolymerization process, microstructure, composition and molecular weight of the polymeric products two new types MAs based on Pluronic (P123 and F68) have been varied from 2 to 10 wt.% (vs. the monomer ε-CL). The structure of the both Pluronic based macroactivators (MAs) and accordingly obtained two series poly (CL-co-Pluronic) polymers were confirmed by ¹H NMR and FT-IR analyses. Additionally, the structure, molecular weight, physicomechanical behavior, thermal stability and morphology of the new synthesized poly (CL–co–Pluronic) polymers have been investigated by Differential Scanning Calorimetry (DSC), Wide-Angle X-ray Diffraction (WAXD), Thermogravimetric Analysis (TGA) and Scanning Electron Microscopy (SEM) analysis.     

Synthesis of poly(ester‐anhydride)s based on poly(ϵ‐caprolactone) prepolymer

The objective of this study was to prepare high molecular weight poly(ester‐anhydride)s by melt polycondensation. The polymerization procedure consisted of the preparation of carboxylic acid terminated poly(?‐caprolactone) prepolymers that were melt polymerized to poly(?‐caprolactone)s containing anhydride functions along the polymer backbone. Poly(?‐caprolactone) prepolymers were prepared using either 1,4‐butanediol or 4‐(hydroxymethyl)benzoic acid as initiators, yielding hydroxyl‐terminated intermediates that were then converted to carboxylic acid‐terminated prepolymers by reaction with succinic anhydride. Prepolymers were then allowed to react with an excess of acetic anhydride, followed by subsequent polycondensation to resulting high molecular weight poly(ester‐anhydride)s. Upon coupling of prepolymers, size exclusion chromatography analyses showed an increase from 3600 to 70,000 g/mol in number‐average molecular weight (M_n) for the 1,4‐butanediol initiated polymer, and an increase from 7200 to 68,000 g/mol for the 4‐(hydroxymethyl)benzoic acid‐initiated polymer. 4‐Hydroxybenzoic acid and adipic acid were also used as initiators in the preparation of poly(?‐caprolactone) prepolymers. However, with these initiators, the results were not satisfactory. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 176–185, 2001     

AB,BAB and (AB)3 poly(ε‐caprolactone)‐based block copolymers with functionalized poly(meth)acrylate segments

Linear and star‐shaped poly(ε‐caprolactone) (PCL) block copolymers containing poly(meth)acrylate segments with glycidyl, 2‐(trimethylsilyloxy)ethyl and tert‐butyl pendant groups were synthesized using mono‐, di‐ and trifunctional PCL macroinitiators and appropriate (meth)acrylate monomers by controlled radical polymerization. The well‐defined structures with narrow molecular weight distributions indicate the coexistence of semi‐crystalline PCL and amorphous poly(meth)acrylic phases. The hydrophobic nature of the block copolymers can be easily converted to amphiphilic, which with biodegradable and biocompatible PCL segments are promising as polymeric carriers in drug delivery systems. © 2012 Society of Chemical Industry     

Synthesis and thermal properties of poly(methyl methacrylate)‐poly(L‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer

Poly(methyl methacrylate)‐poly(L ‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer was prepared using atom transfer radical polymerization (ATRP). The structure and properties of the copolymer were analyzed using infrared spectroscopy, gel permeation chromatography, nuclear magnetic resonance (¹H‐NMR, ¹³C‐NMR), thermogravimetry, and differential scanning calorimetry. The kinetic plot for the ATRP of methyl methacrylate using poly(L ‐lactic acid) (PLLA) as the initiator shows that the reaction time increases linearly with ln[M]₀/[M]. The results indicate that it is possible to achieve grafted chains with well‐defined molecular weights, and block copolymers with narrowed molecular weight distributions. The thermal stability of PLLA is improved by copolymerization. A new wash‐extraction method for removing copper from the ATRP has also exhibits satisfactory results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of the novel block copolymer poly(ε‐caprolactone)‐b‐poly(4‐vinyl pyridine) by the combination of coordination and controlled free‐radical polymerizations

A novel block copolymer, poly(ε‐caprolactone)‐b‐poly(4‐vinyl pyridine), was synthesized with a bifunctional initiator strategy. Poly(ε‐caprolactone) prepolymer with a 2,2,6,6‐tetramethylpiperidinyloxy (TEMPO) end group (PCL_T) was first obtained by coordination polymerization, which showed a controlled mechanism in the process. By means of ultraviolet spectroscopy and electron spin resonance spectroscopy, the TEMPO moiety was determined to be intact in the polymerization. The copolymers were then obtained by the controlled radical polymerization of 4‐vinyl pyridine in the presence of PCL_T. The desired block copolymers were characterized by gel permeation chromatography, Fourier transform infrared spectroscopy, and NMR spectroscopy in detail. Also, the effects of the molecular weight and concentration of PCL_T on the copolymerization were investigated. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2280–2285, 2004     

Fine polystyrene latexes with reactive poly(ethylene oxide) –poly(propylene oxide)–poly(ethylene oxide) triblock macrosurfactants in modified miniemulsion polymerization

Polystyrene latexes were produced via a newly accessible miniemulsion polymerization where reactive poly(ethylene oxide)–poly(propylene oxide) –poly(ethylene oxide) triblock macrosurfactants were used to impart the interfacial activity during the emulsification and the reactivity in the polymerization. Through atomic force microscopy studies, it was found that the polystyrene latexes produced were extremely small to about 50 nm in a proper experimental condition, and covered richly with poly(ethylene oxide) groups. The polystyrene latexes were expected to have great applicability in the production of structured latex films. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 328–332, 2002     

Synthesis and characterization of poly(2‐ethylaniline)–poly(styrenesulfonic acid) and poly(o‐phenetidine)–poly(styrenesulfonic acid) complexes

This research focuses on the synthesis of ethyl and ethoxy substituted polyaniline with poly(styrenesulfonic acid) comprising a poly(o‐phenetidine)–poly(styrenesulfonic acid) [P(O? P)‐PSSA] and poly(2‐ethylaniline)–poly(styrenesulfonic acid) [P(2‐E)‐PSSA]. The complexes P(O? P)‐PSSA and P(2‐E)‐PSSA were prepared by chemical polymerization of monomer (o‐phenetidine, 2‐ethylaniline) with PSSA using an oxidant of ammonium persulfate in 1M HCl solution; polyaniline (PANI), poly(2‐ethylaniline) (P2E), poly(o‐pheneditine) (POP), and polyaniline‐poly(styrenesulfonic acid) (PANI‐PSSA) also were prepared by chemical polymerization to be the reference samples. The products were characterized by IR, VIS, EPR, water solubility, elemental analysis, conductivity, SEM, and TEM. IR spectral studies shown that the structure of P(2‐E)‐PSSA and P(O? P)‐PSSA complexes is similar to that of polyaniline. EPR and visible spectra indicate the formation of polarons. The morphology of the blend was investigated by measured SEM and TEM, indicating the conducting component and electrically conductive property of the polymer complexes. The pH value for deprotonation [pH ≥ 9.5 for P(2‐E)‐PSSA and pH ≥ 8.0 for P(O? P)‐PSSA] are higher than that of corresponding HCl salts, indicating an intimate interaction between polymer chains. Elemental analysis results show that P(O? P)‐PSSA has a nitrogen‐to‐sulfur ratio of ～52%, larger than that for P(2‐E)‐PSSA, ～41%. The conductivity of the complexes is around 10^?2S/cm, and the solubility of P(2‐E)‐PSSA and P(O? P)‐PSSA in water is 2.9 and 1.9 g/L, respectively. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1198–1205, 2005     

Catalyzed chain extension of poly(butylene adipate) and poly(butylene succinate) with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline)

Low‐molecular‐weight HOOC‐terminated poly(butylene adipate) prepolymer (PrePBA) and poly(butylene succinate) prepolymer (PrePBS) were synthesized through melt‐condensation polymerization from adipic acid or succinic acid with butanediol. The catalyzed chain extension of these prepolymers was carried out at 180–220°C with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) as a chain extender and p‐toluenesulfonic acid (p‐TSA) as a catalyst. Higher molecular weight polyesters were obtained from the catalyzed chain extension than from the noncatalyzed one. However, an improperly high amount of p‐TSA and a high temperature caused branching or a crosslinking reaction. Under optimal conditions, chain‐extended poly(butylene adipate) (PBA) with a number‐average molecular weight up to 29,600 and poly(butylene succinate) (PBS) with an intrinsic viscosity of 0.82 dL/g were synthesized. The chain‐extended polyesters were characterized by IR spectroscopy, ¹H‐NMR spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray scattering, and tensile testing. DSC, wide‐angle X‐ray scattering, and thermogravimetric analysis characterization showed that the chain‐extended PBA and PBS had lower melting temperatures and crystallinities and slower crystallization rates and were less thermally stable than PrePBA and PrePBS. This deterioration of their properties was not harmful enough to impair their thermal processing properties and should not prevent them from being used as biodegradable thermoplastics. The tensile strength of the chain‐extended PBS was about 31.05 MPa. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Biodegradable studies of poly(trimethylenecarbonate‐ε‐caprolactone)‐block‐poly(p‐dioxanone), poly(dioxanone), and poly(glycolide‐ε‐caprolactone) (Monocryl®) monofilaments

The aim of the study was to investigate the mechanical properties and biodegradability of poly(trimethylenecarbonate‐ε‐caprolactone)‐block‐poly(p‐dioxanone) [P(TMC‐ε‐CL)‐block‐PDO] in comparison with poly(p‐dioxanone) and poly(glycolide‐ε‐caprolactone) (Monocryl®) monofilaments in vivo and in vitro. P(TMC‐ε‐CL)‐block‐PDO copolymer and poly(p‐dioxanone) were prepared by using ring‐opening polymerization reaction. The monofilament fibers were obtained using conventional melt spun methods. The physicochemical and mechanical properties, such as viscosity, molecular weight, crystallinity, and knot security, were studied. Tensile strength, breaking strength retention, and surface morphology of P(TMC‐ε‐CL)‐block‐PDO, poly(p‐dioxanone), and Monocryl monofilament fibers were studied by immersion in phosphate‐buffered distilled water (pH 7.2) at 37°C and in vivo. The implantation studies of absorbable suture strands were performed in gluteal muscle of rats. The polymers, P(TMC‐ε‐CL)‐block‐PDO, poly(p‐dioxanone), and Monocryl, were semicrystalline and showed 27, 32, and 34% crystallinity, respectively. Those mechanical properties of P(TMC‐ε‐CL)‐block‐PDO were comparatively lower than other polymers. The biodegradability of poly(dioxanone) homopolymer is much slower compared with that of two copolymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 737–743, 2006     

Preparation of poly(vinyl amine)‐grafted crosslinked poly(vinyl alcohol) microspheres

Crosslinked poly(vinyl alcohol) (CPVA) microspheres were first prepared via the suspension polymerization of vinyl acetate and the alcoholysis of poly(vinyl acetate). Afterwards, a two‐step method involving graft polymerization and Hofmann degradation was used to prepare functional poly(vinyl amine)‐grafted crosslinked poly(vinyl alcohol) (PVAm–CPVA) microspheres, onto which poly(vinyl amine) (PVAm) macromolecules were grafted. The graft polymerization of acrylamide (AM) on CPVA microspheres was performed with cerium salt as the initiator in an acidic aqueous medium, resulting in polyacrylamide (PAM)‐grafted CPVA microspheres. Subsequently, the grafted PAM was transformed into PVAm via the Hofmann degradation reaction, and PVAm–CPVA microspheres were prepared. The effects of the main factors on the graft polymerization and Hofmann degradation were examined, and the reaction mechanisms were researched in depth. The experimental results showed that for the graft polymerization of AM on CPVA microspheres initiated by cerium salt, the acid concentration and the amount of cerium salt affected the grafting degree of PAM greatly. For the Hofmann degradation reaction of the grafted PAM, the amination degree of PVAm–CPVA microspheres was obviously affected by the amount of sodium hypochlorite in the presence of sodium hydroxide. The preliminary adsorption tests showed that PVAm–CPVA microspheres were multifunctional and had strong adsorption ability for Fe(III) ions by chelation action and for chromate ions (CrO) by strong electrostatic interactions. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polymer networks based on α,ω-methacrylate-terminated poly(1,3-dioxolane)

α,ω-Methacrylate-terminated poly(1,3-dioxolane)s (polyDXL) were synthesized by cationic ring-opening polymerization of DXL in the presence of methylene-bis(oxyethylmethacrylate) as transfer agent. If the initiator concentration is small compared with the transfer agent concentration, the molecular weights of the polymers are governed by the ratio of the reacted monomer to the reacted transfer agent. The α,ω-methacrylate-terminated polyDXLs obtained undergo free radical polymerization with formation of polyacetal networks. The properties of the networks as function of the molecular weight of the corresponding prepolymers are reported.     

Aerobic oxidative polymerization of 2,6‐dimethylphenol in water with a highly efficient copper(II)– poly(N‐vinylimidazole) complex catalyst

A Cu(II)–poly(N‐vinylimidazole) (PVI) complex was prepared and used to catalyze the oxidative polymerization of 2,6‐dimethylphenol (DMP) to form poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) in water. The stoichiometric ratio between imidazole groups in PVI and copper ions was found to be 4 when continuous variation analysis was applied. Compared with a conventional Cu(II)–low‐molecular‐weight ligand complex, a high catalytic efficiency was observed in the polymerization of DMP catalyzed by the Cu(II)–PVI complex. The influence of the Cu(II)–PVI complex concentration and imidazole/Cu(II) molar ratio on the oxidative polymerization of DMP was studied. Both the yield and molecular weight of PPO increased significantly with the catalyst concentration and decreased with the imidazole/Cu(II) molar ratio. The molecular weight of PVI also played an important role in the improvement of the catalytic efficiency. The high catalytic efficiency of the Cu(II)–PVI complex may have been due to the concentration effect of the catalyst and substrate. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of biodegradable poly(ester‐urethanes) based on bacterial poly(R‐3‐hydroxybutyrate)

A series of poly(R‐3‐hydroxybutyrate)/poly(ε‐caprolactone)/1,6‐hexamethylene diisocyanate‐segmented poly(ester‐urethanes), having different compositions and different block lengths, were synthesized by one‐step solution polymerization. The molecular weight of poly(R‐3‐hydroxybutyrate)‐diol, PHB‐diol, hard segments was in the range of 2100–4400 and poly(ε‐caprolactone)‐diol, PCL‐diol, soft segments in the range of 1080–5800. The materials obtained were investigated by using differential scanning calorimetry, wide angle X‐ray diffraction and mechanical measurements. All poly(ester‐urethanes) investigated were semicrystalline with T_m varying within 126–148°C. DSC results showed that T_g are shifted to higher temperature with increasing content of PHB hard segments and decreasing molecular weight of PCL soft segments. This indicates partial compatibility of the two phases. In poly(ester‐urethanes) made from PCL soft segments of molecular weight (M_n ≥ 2200), a PCL crystalline phase, in addition to the PHB crystalline phase, was observed. As for the mechanical tensile properties of poly(ester‐urethane) cast films, it was found that the ultimate strength and the elongation at the breakpoint decrease with increasing PHB hard segment content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 703–718, 2002