Melt differentiation and crystallization of clinker minerals in a CaO-SiO2-Al2O3-Fe2O3 pseudoquaternary system

In the CaO-SiO₂-Al₂O₃-Fe₂O₃ pseudoquaternary system, the solid solutions of Ca₃SiO₅ [C₃S(ss)], Ca₂SiO₄ [C₂S(ss)], Ca₂(Al_xFe_1 − x)₂O₅ with 0.40 ≤ x ≤ 0.57 (ferrite) and Ca₃Al₂O₆ [C₃A(ss)] were crystallized out of a complete melt with 52.9 mass% CaO and Al₂O₃/Fe₂O₃ = 0.70. When the melt was cooled from 1673 K at 80 K/h, the crystals of ferrite with x = 0.40, C₃S(ss) and C₂S(ss) would start to nucleate from the melt at 1630 K. During further cooling, the x value of the precipitating ferrite would progressively increase and eventually approach 0.57 at 1613 K. The resulting ferrite crystals showed a zonal structure, the x value of which successively increased from the cores toward the rims. Actually, the x values of 0.43 and 0.52 were confirmed for, respectively, the cores and rims by EPMA. As the simultaneous crystallization of zoned ferrite, C₃S(ss) and C₂S(ss) proceeded, the coexisting melt would become progressively enriched in the Al₂O₃ component. After the termination of the ferrite crystallization, the C₃A(ss), C₃S(ss) and C₂S(ss) crystallized out of the differentiated melt. The end result was the four phase mixture of ferrite, C₃A(ss), C₃S(ss) and C₂S(ss), being free from the nucleation of Ca₁₂Al₁₄O₃₃ solid solution.     

Heavy metals in cement phases: on the solubility of Mg, Cd, Pb and Ba in Ca3Al2O6

The compounds formed when the divalent cations Mg²⁺, Cd²⁺, Ba²⁺ and Pb²⁺ are present during the preparation of Ca₃Al₂O₆ have been studied using X-ray microanalysis and diffraction methods. The smaller Mg cations are found to partially substitute for Ca²⁺, and structural refinements show that Mg preferentially occupies the smaller six-coordinate sites in Ca_3−xMg_xAl₂O₆. When Ba is present, it preferentially occupies the larger eight- and nine-coordinate sites. X-ray microanalysis suggests that Pb and Cd are lost from the samples during the preparation process. The diffraction patterns show a small decrease in the lattice parameters, suggesting that a defect structure of the type Ca_3−x(vac)_xAl₂O₆ is formed. The distribution of products formed on hydration of the doped Ca_3−xM_xAl₂O₆ is found to be very different than that observed for the undoped material.     

Influence of MgO on the formation of Ca3SiO5 and 3CaO·3Al2O3·CaSO4 minerals in alite-sulphoaluminate cement

The influence of MgO on the formation of Ca₃SiO₅ and 3CaO·3Al₂O₃·CaSO₄ minerals in alite-sulphoaluminate cement is reported in this paper. The results show that adding a suitable amount of MgO can lower the clinkering temperature, promote the formation of Ca₃SiO₅ and 3CaO·3Al₂O₃·CaSO₄ minerals, and help in the coexistence of the two minerals in the clinker. MgO may obviously decrease the formation of Ca₃Al₂O₆, and increase the SiO₂ content incorporated into the interstitial phase.     

Properties and rapid consolidation of nanostructured Al2O3-Al2SiO5 composites by high frequency induction heated sintering

The rapid sintering of nanostructured Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites was investigated by a high-frequency induction heating sintering process. The advantage of this process is that it allows very quick densification to near theoretical density and inhibition of grain growth. Highly dense nanostructured Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites were produced with simultaneous application of a 80 MPa pressure and induced output current of a total power capacity (15 kW) within 3 min. The sintering behavior, grain size and mechanical properties of Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites were investigated.     

Effects of CaSiO3 addition on sintering behavior and microwave dielectric properties of Al2O3 ceramics

The effects of CaSiO₃ addition on the sintering behavior and microwave dielectric properties of Al₂O₃ ceramics have been investigated. The addition of CaSiO₃ into Al₂O₃ ceramics resulted in the emergence of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈, which acting as liquid sintering aids can effectively lower the sintering temperature of Al₂O₃ ceramic. The Q × f value of Al₂O₃-CaSiO₃ ceramics decreased with the CaSiO₃ addition increasing because of the lower Q × f value of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈. Compared with the pure CaSiO₃ ceramic, the Al₂O₃-CaSiO₃ ceramic with 20 wt% CaSiO₃ addition possessed good dielectric properties of ?_r = 9.36 and Q × f = 13,678 GHz at the similar sintering temperature.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Phase diagram of the Al2O3-HfO2-Y2O3 system

The phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system was first constructed in the temperature range 1200-2800 °C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this system. Four new ternary and three new quasibinary eutectics were found. The minimum melting temperature is 1755 °C and it corresponds to the ternary eutectic Al₂O₃ + HfO₂ + Y₃Al₅O₁₂. The solidus surface projection, the schematic of the alloy crystallization path and the vertical sections present the complete phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system.     

Phase separation induced by hydration of the mixed Ca/Sr aluminates Ca3−xSrxAl2O6: A crystallographic study

The compounds formed by the hydration of single-phase samples of the mixed, solid solution, Ca/Sr aluminates, Ca_3−xSr_xAl₂O₆, 3≤x≤0 have been studied using high-resolution synchrotron powder diffraction. Hydration of these mixed metal aluminates generally resulted in the formation of at least two hydrogarnet phases, one Ca-rich and the other Sr-rich. The structures of these hydrogarnets have been refined from neutron or synchrotron powder X-ray diffraction (XRD) data. A simple solubility model to explain the phase separation is presented.     

Effects of Al2O3 addition on the sintering behavior and microwave dielectric properties of CaSiO3 ceramics

The effects of Al₂O₃ addition on the densification, structure and microwave dielectric properties of CaSiO₃ ceramics have been investigated. The Al₂O₃ addition results in the presence of two distinct phases, e.g. Ca₂Al₂SiO₇ and CaAl₂Si₂O₈, which can restrict the growth of CaSiO₃ grains by surrounding their boundaries and also improve the bulk density of CaSiO₃-Al₂O₃ ceramics. However, excessive addition (≥2 wt%) of Al₂O₃ undermines the microwave dielectric properties of the title ceramics since the derived phases of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈ have poor quality factor. The optimum amount of Al₂O₃ addition is found to be 1 wt%, and the derived CaSiO₃-Al₂O₃ ceramic sintered at 1250 °C presents improved microwave dielectric properties of ?_r = 6.66 and Q × f = 24,626 GHz, which is much better than those of pure CaSiO₃ ceramic sintered at 1340 °C (Q × f = 13,109 GHz).     

Support modification to improve the sulphur tolerance of Ag/Al2O3 for SCR of NOx with propene under lean-burn conditions

Ag/Al₂O₃ catalysts with 1 wt% SiO₂ or TiO₂ doping in alumina support have been prepared by wet impregnation method and tested for sulphur tolerance during the selective catalytic reduction (SCR) of NO_x using propene under lean conditions. Ag/Al₂O₃ showed 44% NO_x conversion at 623 K, which was drastically reduced to 21% when exposed to 20 ppm SO₂. When Al₂O₃ support in Ag/Al₂O₃ was doped with 1 wt% SiO₂ or TiO₂ the NO_x conversion remained constant in presence of SO₂ showing the improved sulphur tolerance of these catalysts. Subsequent water addition does not induce significant deactivation. On the contrary, a slight promotional effect on the activity of NO conversion to nitrogen is observed after Si and Ti incorporation. FTIR study showed the sulphation of silver and aluminum sites of Ag/Al₂O₃ catalysts resulting in the decrease in the formation of reactive intermediate species such as –NCO, which in turn decreases NO_x conversion to N₂. In the case of Ag/Al₂O₃ doped with SiO₂ or TiO₂, formation of silver sulphate and aluminum sulphate was drastically reduced, which was evident in FTIR resulting in remarkable improvement in the sulphur tolerance of Ag/Al₂O₃ catalyst. These catalysts before and after the reaction have been characterized with various techniques (XRD, BET surface area, transmittance FTIR and pyridine adsorption) for physico-chemical properties.     

Large-scale fine structural alumina matrix ceramic guideway materials improved by diopside and Fe2O3

Diopside and Fe₂O₃ were introduced in alumina matrix ceramic materials. Large-scale fine structural alumina matrix ceramic guideway materials were fabricated by the technology of pressureless sintering, during which liquid phase sintering took place and new phases such as 3Al₂O₃·2SiO₂, CaO·Al₂O₃·2SiO₂ and CaO·6Al₂O₃ were produced by the chemical reactions taking place among alumina and the additives. The hardness, the fracture toughness and the bending strength of the guideway products were tested. The influences of diopside and Fe₂O₃ additions were studied by microstructural observations and mechanical properties evaluations. Meanwhile, the expected improvement of mechanical properties compared with pure alumina was indeed observed. The fracture mechanism and porosity of large-scale fine structural alumina matrix ceramic guideway materials were analyzed.     

Ethanol steam reforming reactions over Al2O3 · SiO2-supported Ni-La catalysts

Nickel-based catalysts supported on Al₂O₃ · SiO₂ were prepared with modification of the second metal involving La, Co, Cu, Zr or Y, of which the catalytic behaviors were assessed in the ethanol steam reforming reaction. Activity test indicated that addition of La resulted in higher selectivity of hydrogen and lower selectivity of carbon monoxide, compared with Co-doped nickel catalyst. Influences of lanthanum amounts on catalytic performance were studied over 30NixLa/Al₂O₃ · SiO₂ (x = 5, 10, 15), and characterizations by XRD, TPR and XPS indicated that low amount of lanthanum additives (5%) was superior to inhibit the crystal growth of nickel as well as beneficial to the reduction of nickel oxide. Finally 100 h test for the optimal catalyst 30Ni5La/Al₂O₃ · SiO₂ indicated its good long-term stability to provide high hydrogen selectivity and low carbon monoxide formation, as well as good resistance to coke deposition at low temperature.     

Mixed oxides Ca2Fe2O5 and Ca2Co2O5 as anode materials for Li-ion batteries

The electrochemical performance of mixed oxides, Ca₂Fe₂O₅ and Ca₂Co₂O₅ for use in Li-ion batteries was studied with Li as the counter electrode. The compounds were prepared and characterized by X-ray diffraction and SEM. Ca₂Fe₂O₅ showed a reversible capacity of 226 mAh/g at the 14th cycle and retained 183 mAh/g at the end of 50 cycles at 60 mA/g in the voltage window 0.005-2.5 V. A reversible capacity in the range, 365-380 mAh/g, which is stable up to 50 charge-discharge cycles is exhibited by Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V and at 60 mA/g. This corresponds to recycleable moles of Li of 3.9±0.1 (theoretical: 4.0). Significant improvement in the cycling performance and attainable reversible capacity were noted for Ca₂Co₂O₅ on cycling to an upper cut-off voltage of 3.0 V as compared to 2.5 V. Coulombic efficiency for both compounds is >98%. Electrochemical impedance spectroscopy (EIS) data clearly indicate the reversible formation/decomposition of polymeric surface film on the electrode surface of Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V. Cyclic voltammetry results compliment the galvanostatic cycling data.     

Selective synthesis of mixed alcohols from syngas over catalyst Fe2O3/Al2O3 in slurry reactor

The Fe₂O₃/Al₂O₃ catalyst was studied to selectively synthesize mixed alcohols from syngas in a continuously stirred slurry reactor with the oxygenated solvent Polyethylene Glycol-400 (PEG-400). The selectivity of mixed alcohols in the products reached as high as 95 wt.% and the C₂₊ alcohols (mainly ethanol) was more than 40 wt.% in the total alcohol products at the reaction conditions of 250 °C, 3.0 MPa, H₂/CO = 2 and space velocity = 360 ml/g_cat h. The hydrogen temperature programmed reduction (H₂-TPR) and X-ray photoelectron spectroscopy (XPS) measurements of the catalyst confirmed that the FeO phase was responsible for the high selectivity to mixed alcohols in the process. And the oxygenated solvent PEG-400 was also necessary for the selective synthesis of mixed alcohols in the reaction system.     

Enhanced thermoelectric properties induced by chemical pressure in Ca3Co4O9

We report the investigation of boron substitution on structural, electrical, thermal, and thermoelectric properties of Ca_3−xB_xCo₄O₉ (x=0, 0.5, 0.75, and 1) in the temperature range between 300 K and 5 K. X-ray diffraction studies show that the Ca₃Co₄O₉ phase is successfully preserved as the majority phase in the x=0.5 sample despite the small size of boron ions. Electrical transport measurements confirm that B³⁺ substitution for Ca²⁺ causes an increase in resistivity due to the decrease in carrier concentration. x=0.5 sample is found to have a Seebeck coefficient of 181 μV/K at room temperature which is ~1.5 times higher than that of the pure Ca₃Co₄O₉. Our results indicate that the chemical pressure due to the large ionic radii difference between B³⁺ (0.27 Å) and Ca²⁺ (1 Å) enhances the thermoelectric properties as long as the unique crystal structure of Ca₃Co₄O₉ is preserved.     

Combustion synthesis of (Ti1−xNbx)2AlC solid solutions from elemental and Nb2O5/Al4C3-containing powder compacts

Preparation of the (Ti_1−xNb_x)₂AlC solid solution (formed from the M_n+1AX_n or MAX carbides, where n = 1, 2, or 3, M is an early transition metal, A is an A-group element, and X is C) with x = 0.2-0.8 was investigated by self-propagating high-temperature synthesis (SHS). Nearly single-phase (Ti,Nb)₂AlC was produced through direct combustion of constituent elements. Due to the decrease of reaction exothermicity, the combustion temperature and reaction front velocity decreased with increasing Nb content of (Ti_1−xNb_x)₂AlC formed from the elemental powder compacts. In addition, the samples composed of Ti, Al, Nb₂O₅, and Al₄C₃ were adopted for the in situ formation of Al₂O₃-added (Ti,Nb)₂AlC. The SHS process of the Nb₂O₅/Al₄C₃-containing sample involved aluminothermic reduction of Nb₂O₅, which not only enhanced the reaction exothermicity but also facilitated the evolution of (Ti,Nb)₂AlC. Based upon the XRD analysis, two intermediates, TiC and Nb₂Al, were detected in the (Ti,Nb)₂AlC/Al₂O₃ composite and their amounts were reduced by increasing the extent of thermite reduction involved in the SHS process. The laminated microstructure characteristic of the MAX carbide was observed for both monolithic and Al₂O₃-added (Ti,Nb)₂AlC solid solutions synthesized in this study.     

A crucial role of O2 and O2 on mayenite structure for biomass tar steam reforming over Ni/Ca12Al14O33

Newly synthesized nickel calcium aluminum catalysts (Ni/Ca₁₂Al₁₄O₃₃) were tested in a fixed bed reactor for biomass tar steam reforming, toluene as tar destruction model compound. Four catalysts (Ni/Ca₁₂Al₁₄O₃₃) were prepared with Ni loading amount from 1, 3, 5 to 7 wt%, even 1% loading catalyst also showed excellent performance. Catalysts aged experiments in the absence (60 h on stream) and presence of H₂S were characterized by BET, X-ray diffraction (XRD), and Raman spectra. It was observed that Ni/Ca₁₂Al₁₄O₃₃ showed excellent sustainability against coke formation due to the “free oxygen” in the catalysts. It also exhibited higher H₂S-poisoning resistance property compared to the commercial catalysts Ni/Al₂O₃ (5%) and Ni/CaO_0.5/MgO_0.5. Raman spectra revealed that “free oxygen O₂⁻ and O₂²⁻” in the structure of the catalysts could be substituted by sulfur then protected Ni poisoning on some degree, but reactivation experiments by O₂ flowing showed that the sulfide Ni/Ca₁₂Al₁₄O₃₃ was difficult to completely restore, incorporation of sulfur in the structure only partly regain by O₂. The kinetic model proposes, as generally accepted, a first-order reaction for toluene with activation energy of 82.06 kJ mol⁻¹ was coincident with the literature data. The Ni/Ca₁₂Al₁₄O₃₃ catalyst was effective and relative cheap, which may be lead to reduction in the cost of hot gas cleaning process.     

Mechanical properties of Al2O3-Cr2O3/Cr3C2 nanocomposite fabricated by spark plasma sintering

The fine grains of Al₂O₃-Cr₂O₃/Cr-carbide nanocomposites were prepared by employing recently developed spark plasma sintering (SPS) technique. The initial materials were fabricated by a metal organic chemical vapor deposition (MOCVD) process, in which Cr(CO)₆ was used as a precursor and Al₂O₃ powders as matrix in a spouted chamber. The basic mechanical properties like hardness, fracture strength and toughness, and the nanoindentation characterization of nanocomposites such as Elastics modulus (E), elastic work (W_e) and plastic work (W_p) were analyzed. The microstructure of dislocation, transgranular and step-wise fracture surface were observed in the nanocomposites. The nanocomposites show fracture toughness of (4.8 MPa m^1/2) and facture strength (780 MPa), which is higher than monolithic alumina. The strengthening mechanism from the secondary phase and solid solution are also discussed in the present work. Nanoindentation characterization further illustrates the strengthening of nanocomposites.     

Influence of CuO on the formation and coexistence of 3CaO·SiO2 and 3CaO·3Al2O3·CaSO4 minerals

The influence of CuO on the formation and coexistence of 3CaO·SiO₂ and 3CaO·3Al₂O₃·CaSO₄ minerals in Portland cement containing 3CaO·3Al₂O₃·CaSO₄ mineral is reported in this paper. The results show that a suitable amount of CuO can lower the clinkering temperature and improve the burn-ability of clinkers. It can also promote the formation of 3CaO·SiO₂ and 3CaO·3Al₂O₃·CaSO₄ minerals and facilitate the coexistence of the two minerals in the clinkers. But adding 1% CuO to the raw material can cause the decomposition of 3CaO·3Al₂O₃·CaSO₄.     

Fuel mixture approach for solution combustion synthesis of Ca3Al2O6 powders

Single-phase 3CaO·Al₂O₃ powders were prepared via solution combustion synthesis using a fuel mixture of urea and β-alanine. The concept of using this fuel mixture comes from the individual reactivity of calcium nitrate and aluminum nitrate with respect to urea and β-alanine. It was proved that urea is the optimum fuel for Al(NO₃)₃ whereas β-alanine is the most suitable fuel for Ca(NO₃)₂. X-ray diffraction and thermal analysis investigations revealed that heating at 300 °C the precursor mixture containing the desired metal nitrates, urea and β-alanine triggers a vigorous combustion reaction, which yields single-phase nanocrystalline 3CaO·Al₂O₃ powder (33.3 nm). In this case additional annealing was no longer required. The use of a single fuel failed to ensure the formation of 3CaO·Al₂O₃ directly from the combustion reaction. After annealing at 900 °C for 1 h, the powders obtained by using a single fuel (urea or β-alanine) developed a phase composition comprising of 3CaO·Al₂O₃, 12CaO·7Al₂O₃ and CaO.