Utilization of carbon dioxide as soft oxidant for oxydehydrogenation of ethylbenzene to styrene over V2O5–CeO2/TiO2–ZrO2 catalyst

Vanadium oxide and cerium oxide doped titania–zirconia mixed oxides were explored for oxidative dehydrogenation of ethylbenzene to styrene utilizing carbon dioxide as a soft oxidant. The investigated TiO₂–ZrO₂ mixed oxide support with high specific surface area (207 m² g⁻¹) was synthesized by a coprecipitation method. Over the calcined support (550 °C), a monolayer equivalent (15 wt.%) of V₂O₅, CeO₂ or a combination of both were deposited by using wet-impregnation or co-impregnation methods to make the V₂O₅/TiO₂–ZrO₂, CeO₂/TiO₂–ZrO₂ and V₂O₅–CeO₂/TiO₂–ZrO₂ combination catalysts, respectively. These catalysts were characterized using X-ray diffraction (XRD), Raman, scanning electron microscopy (SEM), transmission electron microscopy (TEM), temperature preprogrammed reduction (TPR), CO₂ temperature preprogrammed desorption (TPD) and BET surface area methods. All characterization studies revealed that the deposited promoter oxides are in a highly dispersed form over the support, and the combined acid–base and redox properties of the catalysts play a major role in this reaction. The V₂O₅–CeO₂/TiO₂–ZrO₂ catalyst exhibited a better conversion and product selectivity than other combinations. In particular, the addition of CeO₂ to V₂O₅/TiO₂–ZrO₂ prevented catalyst deactivation and helped to maintain a high and stable catalytic activity.     

Synthesis and characterization of CuO/TiO2 catalysts for low-temperature CO oxidation

In this paper, the CuO/TiO₂ catalysts prepared by the deposition–precipitation (DP) method were extensively investigated for CO oxidation reaction. The structural characters of the CuO/TiO₂ catalysts were comparatively investigated by TG-DTA, XRD, and XPS measurements. It was shown that the catalytic behavior of CuO/TiO₂ catalysts greatly depended on the TiO₂-support calcination temperature, the CuO loading amount and the CuO/TiO₂ catalysts calcination temperature. CuO supported on the anatase phase of TiO₂-support calcined at 400 °C showed better catalytic activity than those supported on TiO₂ calcined at 500 and 700 °C. Among all our investigated catalysts with CuO loading from 2% to 12%, the catalyst with 8 wt% CuO loading exhibited the highest catalytic activity. The optimum calcination temperature of the CuO/TiO₂ catalysts was 300 °C. The XRD results indicated that the catalytic activity of the CuO/TiO₂ catalysts was related to the crystal phase and particle size of TiO₂ support and CuO active component.     

Evaluation and characterization of Mn-Cu mixed oxide catalysts supported on TiO2 and ZrO2 for ethanol total oxidation

MnCu/ZrO₂T and MnCu/TiO₂T (T = calcination temperature) catalysts were prepared by the sol-gel method with a Mn:Cu = 5:1 ratio and calcined at different temperatures, T = 673, 873 and 1073 K. The samples were characterized by X-ray diffraction, measurement of specific surface area, temperature programmed reduction, XPS and FT-IR spectroscopy. For both groups of catalysts, the increase of calcination temperature produced three effects: the segregation of phases, an increase of the crystallinity, and a phase transformation of the support. The catalytic activity was evaluated in total oxidation of ethanol, considered as model molecule of VOC. The MnCu/TiO₂ 673 and MnCu/ZrO₂ 873 catalysts showed the best catalytic performance, which was associated with the high dispersion of the MnO_x and CuO_x active phases. The catalytic activity of MnCu/TiO₂ 673 catalyst was also favored by its high surface area.     

CO2 hydrogenation to methanol over Cu/ZnO/ZrO2 catalysts prepared via a route of solid-state reaction

Cu/ZnO/ZrO₂ catalysts were prepared by a route of solid-state reaction and tested for the synthesis of methanol from CO₂ hydrogenation. The effects of calcination temperature on the physicochemical properties of as-prepared catalysts were investigated by N₂ adsorption, XRD, TEM, N₂O titration and H₂-TPR techniques. The results show that the dispersion of copper species decreases with the increase in calcination temperature. Meanwhile, the phase transformation of zirconia from tetragonal to monoclinic was observed. The highest activity was achieved over the catalyst calcined at 400 °C. This method is a promising alternative for the preparation of highly efficient Cu/ZnO/ZrO₂ catalysts.     

Reduction of NO by CO on Cu/ZrO2/Al2O3 catalysts: Characterization and catalytic activities

ZrO₂, γ-Al₂O₃ and ZrO₂/γ-Al₂O₃-supported copper catalysts have been prepared, each with three different copper loads (1, 2 and 5 wt%), by the impregnation method. The catalysts were characterized by nitrogen adsorption (BET), X-ray diffraction (XRD), temperature programmed reduction (TPR) with H₂, Raman spectroscopy and electronic paramagnetic resonance (EPR). The reduction of NO by CO was studied in a fixed-bed reactor packed with these catalysts and fed with a mixture of 1% CO and 1% NO in helium. The catalyst with 5 wt% copper supported on the ZrO₂/γ-Al₂O₃ matrix achieved 80% reduction of NO. Approximately the same rate of conversion was obtained on the catalyst with 2 wt% copper on ZrO₂. Characterization of these catalysts indicated that the active copper species for the reduction of NO are those in direct contact with the oxygen vacancies found in ZrO₂.     

Characterization of Supported NiSO4 and Effect of TiO2–ZrO2 Composition on Catalytic Activity for Acid Catalysis

A series of catalysts, NiSO₄/TiO₂–ZrO₂ having different TiO₂–ZrO₂ composition, for acid catalysis was prepared by the impregnation method using an aqueous solution of nickel sulfate. The addition of TiO₂ to ZrO₂ improved the surface area of the catalyst and enhanced its acidity remarkably because of the formation of new acid sites through the charge imbalance of Ti–O–Zr bonding. The binary oxide, TiO₂–ZrO₂ calcined above 600 °C resulted in the formation of crystalline orthorhombic phase of ZrTiO₄. Therefore, NiSO₄/TiO₂–ZrO₂ calcined at 500 °C exhibited a maximum catalytic activity for acid catalysis, and then the catalytic activity decreased with the calcination temperature. The correlation between catalytic activity and acidity held for both reaction, 2-propanol dehydration and cumene dealkylation. NiSO₄ supported on 50TiO₂–50ZrO₂ (TiO₂/ZrO₂ ratio = 1) among TiO₂–ZrO₂ binary oxides exhibited the highest catalytic activity for acid catalysis.     

Effect of TiO2 loading on the activity of V/TiO2-Al2O3 in the catalytic oxidehydrogenation of ethylbenzene with carbon dioxide

TiO₂-Al₂O₃ mixed oxides with different compositions ranging from 40wt-% to 95wt-% of TiO₂ were prepared by sol-gel method and impregnated with different amounts of VO _x . Supports and catalysts were characterized by X-ray diffraction (XRD), physisorption, temperature preprogrammed reduction (H₂-TPR), and ammonia temperature programmed desorption (NH₃-TPD). TiO₂ content in the support had obvious effect on the crystal structure, texture characteristic, acid property, and catalytic activity in dehydrogenation of ethylbenzene (EB) with carbon dioxide. The highest catalytic activity was acquired when the TiO₂ content was 50 wt-%.     

Chlorobenzene total oxidation over palladium supported on ZrO2, TiO2 nanostructured supports

Two series of supported Pd catalysts were synthesized on new mesoporous–macroporous supports (ZrO₂, TiO₂) labelled M (Zr and Ti). The deposition of palladium was carried out by wet impregnation on the calcined TiO₂ and ZrO₂ supports at 400 °C (Pd/Zr₄, Pd/Ti₄) and 600 °C (Pd/Zr₆, Pd/Ti₆) and followed by a calcination at 400 °C for 4 h. The pre-reduced Pd/MX catalysts were investigated for the chlorobenzene total oxidation and their catalytic properties where compared to those of a reference catalyst Pd/Ti-Ref (TiO₂ from Huntsman Tioxide recalcined at 500 °C) and of a palladium supported on the fresh mesoporous–macroporous TiO₂ (Pd/Ti). Based on the activity determined by T₅₀, the Pd/Ti and Pd/Ti₄ catalysts have been found to be more active than the reference one. Moreover activity decreased owing to the sequence: Pd/TiX  Pd/ZrX and in each series when the temperature of calcination of the support was raised. The overall results clearly showed that the activity was dependant on the nature of the support. The better activity of Pd/TiX compared to Pd/ZrX was likely due to a better reducibility of the TiO₂ support (Ti⁴⁺ into Ti³⁺) leading to an enhancement of the oxygen mobility. Production of polychlorinated benzenes PhCl_x (x = 2–6) and of Cl₂ was also observed. Nevertheless at 500 °C the selectivity in HCl was higher than 90% for the best catalysts.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

Carbon dioxide reforming of ethanol over Ni/Y2O3–ZrO2 catalysts

Supported nickel catalysts of composition Ni/Y₂O₃–ZrO₂ were synthesized in one step by the polymerization method and compared with a nickel catalyst prepared by wet impregnation. Stronger interactions were observed in the formed catalysts between NiO species and the oxygen vacancies of the Y₂O₃–ZrO₂ in the catalysts made by polymerization, and these were attributed to less agglomeration of the NiO during the synthesis of the catalysts in one step. The dry reforming of ethanol was catalyzed with a maximum CO₂ conversion of 61% on the 5NiYZ catalyst at 800 °C, representing a better response than for the catalyst of the same composition prepared by wet impregnation.     

Effect of calcination treatment of zirconia on W/ZrO2 catalysts for transesterification

In this present study, the nanocrystalline ZrO₂ particles synthesized by the solvothermal method were calcined in reductive (H₂), inert (N₂) and oxidative (O₂ and air) atmospheres prior to impregnation with tungsten (W) in order to produce the W/ZrO₂ (WZ) catalysts. Based on the ESR measurement, it revealed that only the ZrO₂ samples calcined in H₂ and N₂ exhibited the F-center (single charged oxygen vacancy) at g = 2.003. None of Zr³⁺ defect was detected for all calcined ZrO₂ samples. After impregnation with tungsten, the WZ catalysts were also characterized. It was present as the polycrystal, which can be seen by the selected area electron distribution (SAED). However, the presence of Zr³⁺ defect was evident in all WZ catalysts, while the F-center was absent. The highest Zr³⁺ intensity detected in the WZ catalyst using ZrO₂ under H₂ calcination atmosphere can be attributed to the transformation of F-center to Zr³⁺ defect. It revealed that the WZ-H₂ catalyst exhibited the highest conversion under transesterification of triacetin and methanol among other WZ catalysts. This can be attributed to the high surface acidity, which was probably induced by large amounts of Zr³⁺ defect.     

Synthesis of bio-additives: Acetylation of glycerol over zirconia-based solid acid catalysts

Acetylation of glycerol with acetic acid was investigated over ZrO₂, TiO₂–ZrO₂, WO_x/TiO₂–ZrO₂ and MoO_x/TiO₂–ZrO₂ solid acid catalysts to synthesize monoacetin, diacetin and triacetin having interesting applications as bio-additives for petroleum fuels. The prepared catalysts were characterized by means of XRD, BET surface area, ammonia-TPD and FT-Raman techniques. The effect of various parameters such as reaction temperature, molar ratio of acetic acid to glycerol, catalyst wt.% and time-on-stream were studied to optimize the reaction conditions. Among various catalysts investigated, the MoO_x/TiO₂–ZrO₂ combination exhibited highest conversion (~ 100%) with best product selectivity, and a high time-on-stream stability.     

NOx storage behavior and sulfur-resisting performance of the third-generation NSR catalysts Pt/K/TiO2–ZrO2

The NO_x storage and reduction (NSR) catalysts Pt/K/TiO₂–ZrO₂ were prepared by an impregnation method. The techniques of XRD, NH₃-TPD, CO₂-TPD, H₂-TPR and in situDRIFTS were employed to investigate their NO_x storage behavior and sulfur-resisting performance. It is revealed that the storage capacity and sulfur-resisting ability of these catalysts depend strongly on the calcination temperature of the support. The catalyst with theist support calcined at 500 °C, exhibits the largest specific surface area but the lowest storage capacity. With increasing calcination temperature, the NO_x storage capacity of the catalyst improves greatly, but the sulfur-resisting ability of the catalyst decreases. In situ DRIFTS results show that free nitrate species and bulk sulfates are the main storage and sulfation species, respectively, for all the catalysts studied. The CO₂-TPD results indicate that the decomposition performance of K₂CO₃ is largely determined by the surface property of the TiO₂–ZrO₂ support. The interaction between the surface hydroxyl of the support and K₂CO₃ promotes the decomposition of K₂CO₃ to form –OK groups bound to the support, leading to low NO_x storage capacity but high sulfur-resisting ability, while the interaction between the highly dispersed K₂CO₃ species and Lewis acid sites gives rise to high NO_x storage capacity but decreased sulfur-resisting ability. The optimal calcination temperature of TiO₂–ZrO₂ support is 650 °C.     

Effect of support modification on the chlorobenzene hydrodechlorination activity on Pt/Al2O3 catalysts

Al₂O₃ was modified with TiO₂ and ZrO₂ using organometallic precursors and is used in the preparation of supported platinum catalysts. The catalysts have been characterised by nitrogen adsorption, hydrogen chemisorption and X-ray diffraction and were tested for their activity in the hydrodechlorination of chlorobenzene. The investigations show that support modification controls the catalyst deactivation remarkably and the catalysts were found to be highly active and selective. This revised version was published online in July 2006 with corrections to the Cover Date.     

Oxidation of o-Xylene to Phthalic Anhydride on Sb-V/ZrO2 Catalysts

Zirconia-supported and bulk-mixed vanadiumantimonium oxide catalysts were used for the oxidation of o-xylene to phthalic anhydride. X-ray diffraction, Raman spectroscopy and photoelectron spectroscopy were used for characterization. It was found that vanadium promotes the transition of tetragonal to monoclinic zirconia. The simultaneous presence of Sb and V on zirconia at low coverage led to a preferential interaction of individual V and Sb oxides with the zirconia surface rather than the formation of a binary Sb-V oxide, while at higher Sb-V contents the formation of SbVO₄ took place. Sb-V/ZrO₂ catalysts showed high activity for o-xylene conversion and better selectivity to phthalic anhydride as compared to V/ZrO₂ catalysts. However, their selectivity to phthalic anhydride was poor in comparison to a V/TiO₂ commercial catalyst. The improved selectivity of the Sb-containing catalysts is attributed to the blocking of non-effective surface sites of ZrO₂, the decrease of the total amount of acid sites and the formation of surface V-O-Sb-O-V structures.     

Novel stereo controlled glycosylation of 1,2,3,4,6-penta-o-acetyl-β-d-glucopyranoside using MgO–ZrO2 as an environmentally benign catalyst

Glycosylation reactions are most commonly encountered in nature. Synthetically, glycosylations are carried out with Lewis acid catalysts or mineral acids. However an environmental threat associated with catalysts has encouraged process modification by alternative development of solid catalysts based glycosylation reactions, which are commercially viable as well. In this contribution comparative study of glycosidic bond formation of 1,2,3,4,6-penta-o-acetyl-β-d-glucopyranoside with various alcohols over variety of reaction promoters/catalyst like p-toluene sulphonic acid, HCl, H₂SO₄ and MgO–ZrO₂ were taken up to evaluate the performance of this potential promoter/catalysts systems. The best catalyst for the selective synthesis of alkyl-β-d-glucopyranosides was MgO–ZrO₂ which remains active upto three runs. This replacement of homogeneous acid catalysts by heterogeneous base catalyst shows alkyl-β-d-glucopyranoside as major product at comparatively low temperature range. The effects of variety of parameters were studied in a batch reactor. The mechanism of the reaction over basic mixed metal oxide at 363 K is put forth.     

Carbon dioxide reforming of methane over Co-X/ZrO2 catalysts (X = La,Ce, Mn,Mg, K)

Dry reforming of methane has been studied over Co/ZrO₂ catalysts promoted with different metal additives (La, Ce, Mn, Mg, K) aiming to improve the performance of the catalysts and increase their resistance to coking. Scanning electron microscopy studies and different activity levels of the catalysts clearly show that the type of the promoter significantly affected the metal dispersion properties and catalytic performances of Co/ZrO₂ catalysts. La-modified catalyst exhibited high stability, but moderate activity. It showed no severe coke deposition. Ce-doped Co/ZrO₂ displayed the highest activity among all the catalysts prepared and had a very limited activity loss.     

Dimethyl ether conversion to light olefins over the SAPO-34/ZrO2 composite catalysts with high lifetime

The SAPO-34/ZrO₂ composite catalysts using ZrO₂ as a binder were prepared and their performance was investigated for the dimethyl ether to olefins (DTO) reaction. The composite catalysts showed higher catalytic lifetimes than the free SAPO-34 catalyst, while maintaining high selectivity toward light olefins. This suggests that the binder-filled space between the SAPO-34 crystals can provide additional diffusion paths for mass transfer. In the SAPO-34/ZrO₂ composite catalysts with different ZrO₂ contents, the SAPO-34(11 wt%)/ZrO₂ composite catalyst showed the highest catalytic lifetime. It can be concluded that ZrO₂ is one of the best binders for the preparation of SAPO-34/binder composite catalysts.     

Phenol photodegradation with oxygen and hydrogen peroxide over TiO2 and Fe-doped TiO2

Photodegradation of phenol was investigated with two types of oxidant agents in water, oxygen and hydrogen peroxide, at two different reaction pH with a series of nanosized iron-doped anatase TiO₂ catalysts with different iron contents. The catalysts have been prepared by a sol–gel/microemulsion method. Firstly, iron-doped titania catalysts were studied with respect to their activity behavior when oxygen was used as oxidant agent in the photocatalytic degradation of aqueous phenol in comparison with un-doped reference catalysts. Secondly, two catalysts (TiO₂ and 0.7 wt.% Fe-doped TiO₂) were selected to extend the study for the employment of hydrogen peroxide as oxidant at different concentrations and two initial reaction pHs. An enhancement of the photocatalytic activity is observed only for relatively low doping level (ca. 0.7 wt.%) in catalyst calcined at 450 °C preferably using hydrogen peroxide as oxidant agent which is attributable to the partial introduction of Fe³⁺ cations into the anatase structure. Nevertheless, it has been demonstrated that catalyst surface properties can play an important role during phenol photodegradation process on the basis of the analysis of differences found in the photoactivity as a function of reaction pH.     

The CO methanation over NaY-zeolite supported Ni/Co3O4, Ni/ZrO2, Co3O4/ZrO2 and Ni/Co3O4/ZrO2 catalysts

The CO methanation was studied over zeolite NaY supported Ni, Co₃O₄, ZrO₂ catalysts. The XRD, N₂ physisorption and SEM analysis were used in order to characterize the catalysts. Catalytic activities were carried out under a feed composition of 1% CO, 50% H₂ and 49% He between the 125 °C to 375 °C. Except for the Ni/Co₃O₄/NaY catalyst, all catalysts gave high surface area because of the presence of zeolite NaY. Average pore diameter of the catalysts fell into the mesopore diameter range. The highest CO methanation activity was obtained with Ni/ZrO₂/NaY catalyst at which the CO methanation was started after 175 °C and 100% CO conversion was obtained at 275 °C using the same catalyst.