Electrical characterization of inorganic-on-organic diode based InP and poly(3,4-ethylenedioxithiophene)/poly(styrenesulfonate) (PEDOT:PSS)

The electronic properties of metal–organic semiconductor-inorganic semiconductor diode between InP and poly(3,4-ethylenedioxithiophene)/poly(styrenesulfonate) (PEDOT:PSS) polymeric organic semiconductor film have been investigated via current–voltage and capacitance–voltage methods. The Al/PEDOT:PSS/p-InP contact exhibits a rectification behavior with the barrier height value of 0.98 eV and with the ideality factor value of 2.6 obtained from their forward bias current voltage (I–V) characteristics at the room temperature greater than the conventional Al/p-InP (0.83 eV, n = 1.13). This increase in barrier height and ideality factor can be attributed to PEDOT:PSS film formed at Al/p-InP interface.     

Stable organic photovoltaic with PEDOT:PSS and MoOX mixture anode interfacial layer without encapsulation

Herein, we report about an efficient and stable organic photovoltaic that uses a poly(3,4-ethylenedioxythiophene):poly(styrene-sulfonate) (PEDOT:PSS) and molybdenum oxide (MoO_X) mixture for the anode interfacial layer, and that can reach 4.43% power conversion efficiency (PCE) under AM1.5 conditions. Utilizing PEDOT:PSS:MoO_X (1:1), the shelf lifetime of poly(3-hexylthiophene) (P3HT), and indene-C₆₀ bisadduct (ICBA)-based solar cells without encapsulation, can be realized with only a 25% deterioration after 672 h of storage in air. Furthermore, we compare the photovoltaic performance of the P3HT:ICBA-based organic photovoltaic with PEDOT:PSS, and PEDOT:PSS:MoO_X, in which PEDOT:PSS:MoO_X has outperformed the others. In addition, the water vapor transmission rate of PEDOT:PSS:MoO_X is 0.17 gm/(m² day), which is much less than that of PEDOT:PSS.     

Energy level alignment in PCDTBT:PC70BM solar cells: Solution processed NiOx for improved hole collection and efficiency

Solution-based NiO_x outperforms PEDOT:PSS in device performance and stability when used as a hole-collection layer in bulk-heterojunction (BHJ) solar cells formed with poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole) (PCDTBT) and PC₇₀BM. The origin of the enhancement is clarified by studying the interfacial energy level alignment between PCDTBT or the 1:4 blended heterojunctions and PEDOT:PSS or NiO_x using ultraviolet and inverse photoemission spectroscopies. The 1.6 eV electronic gap of PEDOT:PSS and energy level alignment with the BHJ result in poor hole selectivity of PEDOT:PSS and allows electron recombination at the PEDOT:PSS/BHJ interface. Conversely, the large band gap (3.7 eV) of NiO_x and interfacial dipole (?0.6 eV) with the organic active layer leads to a hole-selective interface. This interfacial dipole yields enhanced electron blocking properties by increasing the barrier to electron injection. The presence of such a strong dipole is predicted to further promote hole collection from the organic layer into the oxide, resulting in increased fill factor and short circuit current. An overall decrease in recombination is manifested in an increase in open circuit voltage and power conversion efficiency of the device on NiO_x versus PEDOT:PSS interlayers.     

Influence of aluminium electrode preparation on PCE values of polymeric solar cells based on P3HT and PCBM

The main goal of the paper was investigation of influence of aluminum electrode preparation via thermal evaporation (TE) and the magnetron sputtering (MS) on power conversion efficiency (PCE) of polymeric solar cells. The photovoltaic properties of such three kinds devices based on poly(3-hexylthiophene-2,5-diyl) (P3HT) as ITO/P3HT/Al, ITO/P3HT:PCBM (1:1, w/w)/Al and ITO/PEDOT:PSS/P3HT:PCBM (1:1, w/w)/Al were investigated. For the constructed devices impedance spectroscopy were analyzed. For devices lack of PEDOT:PSS layer or lack of PCBM, photovoltaic parameters were very low and similar to the parameters obtained for device with Al electrode prepared by magnetron sputtering. The devices comprising PEDOT:PSS with P3HT:PCBM showed the best photovoltaic parameters such as a V_OC of 0.60 V, J_SC of 4.61 mA/cm², FF of 0.21, and PCE of 5.7 × 10^?1%.     

Adhesion properties of inverted polymer solarcells: Processing and film structure parameters

We report on the adhesion of weak interfaces in inverted P3HT:PCBM-based polymer solar cells (OPV) with either a conductive polymer, PEDOT:PSS, or a metal oxide, molybdenum trioxide (MoO₃), as the hole transport layer. The PEDOT:PSS OPVs were prepared by spin or spray coating on glass substrates, or slot-die coating on flexible PET substrates. In all cases, we observed adhesive failure at the interface between the P3HT:PCBM with PEDOT:PSS layer. The adhesion energy measured for the solar cells made on glass substrates was about 1.8 J/m², but only 0.5 J/m² for the roll-to-roll processed flexible solar cells. The adhesion energy was insensitive to the PEDOT:PSS layer thickness in the range of 10–40 nm. A marginal increase in adhesion energy was measured with increased O₂ plasma power. Compared to solution processed PEDOT:PSS, we found that thermally evaporated MoO₃ adheres less to the P3HT:PCBM layer, which we attributed to the reduced mixing at the MoO₃/P3HT:PCBM interface during the thermal evaporation process. Insights into the mechanisms of delamination and the effect of different material properties and processing parameters yield general guidelines for the design of more reliable organic photovoltaic devices.     

Effects of tetramethylene sulfone solvent additives on conductivity of PEDOT:PSS film and performance of polymer photovoltaic cells

A solvent additive in PEDOT:PSS solution is one of many methods to improve the conductivity of the poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films. We explore a new type of the solvent additive, namely tetramethylene sulfone (TMS), for the fabrication of the PEDOT:PSS conductive layer in the ITO/PEDOT:PSS/P3HT:PCBM/TiO_x/Al polymer photovoltaic cells, in comparison to a more common dimethyl sulfoxide (DMSO) solvent additive. At optimal conditions, the TMS additive at 10 wt.% has been found to enhance the conductivity of pristine PEDOT:PSS films from 0.04 S/cm up to approximately 189 S/cm, compared with the highest conductivity for the case of the DMSO additive at 15 wt.% of 117 S/cm. Possible mechanisms of this conductivity enhancement, relating to the polymer conformation and the film morphology, have been investigated by Raman spectroscopy, X-ray diffraction, atomic force microscopy, and transmission electron microscopy. The performance of the polymer photovoltaic cells fabricated with the solvent additives PEDOT:PSS films follows a similar trend to the conductivity of the films as a function of the additive concentration. The additives mainly lead to greater short circuit current density (J_sc) of the photovoltaic cells. The highest power conversion efficiency (PCE) of 2.24% of the device has been obtained with the 10 wt.% TMS additive of, compared to the PCE of 1.48% for the standard device without solvent additive.     

Detailed investigation of dependencies of photovoltaic performances of P3HT:PC61BM based solar cells on anodic work function modified by surface treatment of indium-tin-oxide electrode with benzenesulfonyl chloride derivatives

The photovoltaic (PV) characteristics of bulk-heterojunction (BHJ) solar cells based on poly(3-hexylthiophene) and [6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PC₆₁BM) were improved using indium-tin-oxide (ITO) anode electrodes modified chemically with CH₃O-, H-, Cl-, CF₃-, and NO₂-terminated benzenesulfonyl chlorides as a self-assembled monolayer (SAM). The ITO electrode surfaces were easily treated through the chemical modification of the reactive –SO₂Cl binding group, and the work function (WF) of the modified ITO was effectively changed depending on the permanent dipole moments introduced in the para-position of benzenesulfonyl chloride. We examined the correlation between the ITO WFs corrected by the change in the contact potential difference and the calculated dipole moments of the SAM models. Moreover, we examined the PV characteristics of the P3HT:PC₆₁BM based BHJ organic PV cells using the SAMs or poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS)-treated ITOs with different WFs lying within ±0.2 eV from the highest occupied molecular orbital (HOMO) level of P3HT. We found that the enhancement effect of the SAMs on the power-conversion efficiency (η_P) reached a maximum with Cl (η_P = 3.72%), and became larger than that of PEDOT:PSS (η_P = 3.62%). Two distinct J_sc dependencies, increasing and decreasing with the increasing WF of the anode ITO, were observed at higher and lower WFs than the HOMO level of the donor, respectively. Almost constant V_oc values (around 0.6 V) were observed with different SAM-modified ITOs, which suggested that Fermi level pinning was achieved by aligning the anode Fermi level and positive polaronic level of the donor polymer.     

The enhancement of electrical and optical properties of PEDOT:PSS using one-step dynamic etching for flexible application

The conductivity enhancement of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) by dynamic etching process was investigated to introduce the outstanding and simplest method for soft electronics. Four different samples which were pristine PEDOT:PSS, PEDOT:PSS doped with 5 wt.% DMSO, PEDOT:PSS with dipping process, and PEDOT:PSS with dynamic etching process were prepared to compare the properties such as conductivity, morphology, relative atomic percentage, and topography. All samples were characterized by four point probe, current atomic force microscopy (C-AFM), X-ray photoelectron spectroscopy (XPS), and UV–visible spectroscopy. The conductivity of the sample with dynamic etching process showed the highest value as 1299 S/cm among four samples. We proved that the dynamic etching process is superior to remove PSS phase from PEDOT:PSS film, to flow strong current through entire surface of PEDOT:PSS, and to show the smoothest surface (RMS 2.28 nm). XPS analysis was conducted for accurate chemical and structural surface environments of four samples and the relative atomic percentage of PEDOT in the sample with dynamic etching was the highest as 29.5%. The device performance of the sample with the dynamic etching process was outstanding as 10.31 mA/cm² of J_sc, 0.75 eV of V_oc, 0.46 of FF, and 3.53% of PCE. All properties and the device performance for PEDOT:PSS film by dynamic etching process were the most excellent among the samples.     

Composite film of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) and MoO3 as an efficient hole injection layer for polymer light-emitting diodes

We demonstrate improved performances in polymer light-emitting diodes (PLEDs) using a composite film of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and MoO₃ powder as a hole injection layer. The PLED with the composite film exhibits the current efficiency of 13.5 cd/A, driving voltage of 3.4 V, and half lifetime of 108.1 h, while those values of the PLED with a pristine PEDOT:PSS was 11.3 cd/A, 3.8 V, and 41.5 h, respectively. We also analyze the morphological, optical and electrical properties of the composite films by atomic force microscopy (AFM), UV–Vis-IR absorption, and ultraviolet photoemission spectroscopy (UPS). This work suggests that mixing MoO₃ into PEDOT:PSS is a simple and promising technique for use solution-based devices as an hole injection layer.     

MoO3/Au/MoO3–PEDOT:PSS multilayer electrodes for ITO-free organic solar cells

The effect of the MoO₃–PEDOT:PSS composite layer in the MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrode on the power conversion efficiency of ITO-free organic solar cells (OSCs) was evaluated. The MoO₃ (30 nm)/Au(12 nm)/MoO₃–PEDOT:PSS (30 nm)/PEDOT:PSS structure showed ~7% more optical transmittance than the MoO₃ (30 nm)/Au (12 nm)/MoO₃(30 nm)/PEDOT:PSS structure at 550 nm wavelength. The OSCs using MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrodes as anodes showed a considerable improvement in power conversion efficiency (PCE), from 1.84% to 2.81%, comparable to ITO based OSCs with PCE of 2.89%. This improvement is attributed to the suppression of MoO₃ dissolution by the acidic hole transport layer (HTL) PEDOT:PSS on the MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrode, resulting in high J_sc, V_oc and FF of the OSCs. This composite based multilayer electrode was shown to be a promising replacement in ITO-free flexible optoelectronic devices.     

Optical properties and conductivity of PEDOT:PSS films treated by polyethylenimine solution for organic solar cells

We report on conductivity and optical property of three different types of poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) films [pristine PH1000 film (PH1000-p), with 5 wt.% ethylene glycol additive (PH1000-EG) and with sulfuric acid post-treatment (PH1000-SA)] before and after polyethylenimine (PEI) treatment. The PEI is found to decrease the conductivity of all the PEDOT:PSS films. The processing solvent of 2-methoxyethanol is found to significantly enhance the conductivity of PH1000-p from 1.1 up to 744 S/cm while the processing solvent of isopropanol or water does not change the conductivity of PH1000-p much. As for the optical properties, the PEI treatment slightly changes the transmittance and reflectance of PH1000-p and PH1000-EG films, while the PEI leads to an substantial increase of the absorptance in the spectral region of 400–1100 nm of the PH1000-SA films. Though the optical property and conductivity of the three different types of PEDOT:PSS films vary with the PEI treatment, the treated PEDOT:PSS films exhibit similar low work function. We demonstrate solar cells with a simple device structure of glass/low-WF PEDOT:PSS/P3HT:ICBA/high-WF PEDOT:PSS cells that exhibit good performance with open-circuit voltage of 0.82 V and fill factor up to 0.62 under 100 mW/cm² white light illumination.     

Effects of UV light-irradiated buffer layer on the performance of polymer solar cells

We investigate the effect of a UV-irradiated poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) buffer layer on the performance of polymer photovoltaic cells based on poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) blends. It was found that UV irradiation can reduce the bulk and contact resistance of PEDOT:PSS films, improving the power conversion efficiency from (3.05 ± 0.04)% to (3.50 ± 0.03)% due to the lower device series resistance under an illumination of AM1.5G, 100 mW/cm². The work function change after UV irradiation and negligible surface morphology change was noticed.     

Enhanced performance in inverted polymer solar cells via solution process: Morphology controlling of PEDOT:PSS as anode buffer layer by adding surfactants

Inverted polymer solar cells were fabricated by adding the amphiphilic surfactant ‘Surfynol 104 series’ to Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as a anode buffer layer by solution process. With the introduction of Surfynol 104 series-added PEDOT:PSS, it was able to form a homogeneous film by adjusting the wettability of a hydrophobic poly(3-hexylthiophene) (P3HT):[6,6]-phenyl C₆₁-butyric acid methyl ester (PCBM) film. With decrease in series resistance (R_S) and increase in shunt resistance (R_SH), as a result, the short circuit current density (J_SC), open circuit voltage (V_OC) and fill factor (FF) of the optimized device were 10.2 mA/cm², 0.63 V and 61.3%, respectively, calculated the power conversion efficiency (PCE) was 4.0%. In addition, the air stability of the fabricated device was improved.     

All-solution-processed inverted polymer solar cells on granular surface-nickelized polyimide

In this study, we prepared all-solution-processed inverted polymer solar cells (PSCs) incorporating two solution-processed electrodes – surface-nickelized polyimide films (NiPI films) as cathodes and high-conductivity poly(3,4-ethylenedioxythiophene)/poly(styrene-sulfonate) (PEDOT:PSS) films as anodes – and an active layer with a bulk heterojunction morphology of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C₆₁-buytyric acid methyl ester (PCBM). The granular Ni thin films, which exhibited good adhesion and high-conductivity (ca. 2778 S cm^?1) on the polyimide (PI) substrates and possessed a work function different from that of pure Ni metal (WF, 5.4 eV). Using ultraviolet photoelectron spectroscopy, we determined that the WF of the NiPI films was ca. 3.9 eV. Prior to the coating of the photoactive layer, the surface of the NiPI films were treated with titanium(diisopropoxide)bis(2,4-pentanedionate) (TIPD) solution to facilitate the deposition of high-quality active layer and further as a hole blocking layer. The solution processed anodes (solvent-modified PEDOT:PSS films) were further coated and subjected to mild oxygen plasma treatment on the active layer. Short exposure (5 s) to the plasma improved the quality of the surface of the active layer for PEDOT:PSS deposition. These inverted PSCs on flexible granular NiPI films provided a power conversion efficiency of 2.4% when illuminated under AM 1.5 conditions (100 mW cm^?2). The phenomenon of light absorption enhancement in those inverted PSCs was observed as indicated in reflective UV–vis, haze factor and external quantum efficiency (EQE) responses. The resulting fill factor (FF) of 0.43 is still significantly lower than the FF of 0.64 for standard devices. When compared to the planar structure, the improvement of absorbance of light and good haze factors was obtained for granular structure which suggests NiPI as a better back contact electrode through enhancing the light trapping and scattering in inverted PSCs.     

Metal salt modified PEDOT:PSS as anode buffer layer and its effect on power conversion efficiency of organic solar cells

The effects of metal chlorides such as LiCl, NaCl, CdCl₂ and CuCl₂ on optical transmittance, electrical conductivity as well as morphology of PEDOT:PSS films have been investigated. Transmittance spectra of spun PEDOT:PSS layers were improved by more than 6% to a maximum of 94% in LiCl doped PEDOT:PSS film. The surface of the PEDOT:PSS films has exhibited higher roughness associated with an increase in the electrical conductivity after doping with metal salts. The improvement in the physical properties of PEDOT:PSS as the hole transport layer proved to be key factors towards enhancing the P3HT:PCBM bulk heterojunction (BHJ) solar cells. These improvements include significantly improved power conversion efficiency with values as high as 6.82% associated with high fill factor (61%) and larger short circuit current density (∼18 mA cm⁻²).     

Charge injection and transport studies of poly(2,7-carbazole) copolymer PCDTBT and their relationship to solar cell performance

The charge injection and transport properties of a high performance semiconducting polymer for organic photovoltaic (OPV) applications, poly[N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT), are investigated by time-of-flight (TOF) and dark-injection space-charge-limited current (DI-SCLC) techniques. OPV cells employing PCDTBT are known to possess power conversion efficiency (PCE) exceeding 6% [1], [2]. While TOF probes only the hole mobilities of a thick film, DI-SCLC is shown to be useful down to a sample thickness of ～200 nm, which is comparable to thicknesses used in OPV cells. We show that for pristine PCDTBT, the hole mobilities for both thick used in TOF and thin films for DI-SCLC are essentially the same, and they are in the range of 0.4–3.0 × 10^?4 cm²/Vs at room temperature. Both poly(3,4-ethylene dioxythioplene) doped with poly(strenesulfonate) (PEDOT:PSS) and molybdenum (VI) oxide (MoO₃) form quasi-Ohmic contacts to PCDTBT with better hole injection from MoO₃. Furthermore, the Gaussian Disorder Model (GDM) was employed to analyze the hopping transport of PCDTBT thin films. We show that PCDTBT possesses a relatively large energetic disorder (σ) of ～129 meV, which is significantly higher than the σ of poly(3-hexylthiophene) (P3HT) processed under similar conditions. The correlation between σ and OPV device performance is addressed.     

Aqueous solution-processed MoO3 as an effective interfacial layer in polymer/fullerene based organic solar cells

The authors demonstrate an effective anode interfacial layer based on aqueous solution-processed MoO₃ (sMoO₃) in poly (3-hexylthiophene) (P3HT) and indene-C60 bisadduct (ICBA) based bulk-heterojunction organic solar cells (PSCs). Various sMoO₃ concentration (0.03–0.25 wt%) was obtained by dissolving MoO₃ powder into deionized water directly with weak solubility. The characteristics of sMoO₃ films evaluated by atomic force microscope (AFM) and scanning electron microscope (SEM) suggest that the sMoO₃ films continuously cover the entire indium tin oxide (ITO) surface. The sMoO₃ based PSCs exhibit comparable power conversion efficiency with poly (3,4-ethylenedioxythiophene)–polystyrenesulfonic acid (PEDOT:PSS) based devices. However, even more importantly, the stability of sMoO₃ based devices have been greatly improved in air under continual light-illumination at 52 mW/cm². Further evaluations on Mo valence states and work function of sMoO₃ films by X-ray photoelectron spectroscopy (XPS) and ultraviolet photoelectron spectroscopy (UPS) demonstrate that the aqueous solution-processed MoO₃ could act as an better anode interfacial layer than the conventional PEDOT:PSS.     

Transparent and flexible amorphous InZnAlO films grown by roll-to-roll sputtering for acidic buffer-free flexible organic solar cells

We report on transparent and flexible amorphous In–Zn–Al–O (a-IZAO) films prepared by roll-to-roll (RTR) sputtering for use as anodes in acidic buffer free flexible organic solar cells (FOSCs). The presence of Zn and Al structural stabilizers in the In₂O₃ matrix produced a completely amorphous structure with the high optical transmittance of 89.25% and the low resistivity of 2.123 × 10⁻³ Ω-cm, as well as the high work function of 5.14 eV, making the a-IZAO films suitable for use as flexible anodes for FOSCs. In addition, the a-IZAO films showed no change in resistance (ΔR) during outer and inner bending fatigue tests due to their good mechanical flexibility. Relative to the power conversion efficiency (1.944%) of a PEDOT:PSS-based FOSCs, a FOSC fabricated by using an a-IZAO anode and without the use of acidic PEDOT:PSS buffer showed greater power conversion efficiency (2.509%), owing to the absence of interfacial reactions between the acidic PEDOT:PSS and the a-IZAO anode.     

Solution processed WO3 layer for the replacement of PEDOT:PSS layer in organic photovoltaic cells

Tungsten oxide layer is formed uniformly by a sol–gel technique on top of indium tin oxide as a neutral and photo-stable hole extraction layer (HEL). The solution processed tungsten oxide layer (sWO₃) is fully characterized by UV–Vis, XPS, UPS, XRD, AFM, and TEM. Optical transmission of ITO/sWO₃ substrates is nearly identical to ITOs. In addition, the sWO₃ layer induces nearly ohmic contact to P3HT as PEDOT:PSS layer does, which is determined by UPS measurement. In case that an optimized thickness (～10 nm) of the sWO₃ layer is incorporated in the organic photovoltaic devices (OPVs) with a structure of ITO/sWO₃/P3HT:PCBM/Al, the power conversion efficiency (PCE) is 3.4%, comparable to that of devices utilizing PEDOT:PSS as HEL. Furthermore, the stability of OPV utilizing sWO₃ is significantly enhanced due to the air- and photo-stability of the sWO₃ layer itself. PCEs are decreased to 40% and 0% of initial values, when PEDOT:PSS layers are exposed to air and light for 192 h, respectively. In contrast, PCEs are maintained to 90% and 87% of initial PCEs respectively, when sWO₃ layers are exposed to the same conditions. Conclusively, we find that solution processed tungsten oxide layers can be prepared easily, act as an efficient hole extraction layer, and afford a much higher stability than PEDOT:PSS layers.     

Effect of PEDOT–PSS resistivity and work function on PLED performance

The effect of a commonly used hole injection layer, poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT–PSS), on polymer light-emitting diode (PLED) performance has been investigated. A series of four different types of commercial PEDOT–PSS, with varying resistivity and work function were examined in devices with the structure Indium Tin Oxide (ITO)/PEDOT–PSS/High Molecular Weight Poly(n-vinylcarbazole) (PVKH): 30% N,N′-bis(3-methylphenyl)-N,N′-diphenylbenzidine (TPD)/Low molecular Weight Poly(n-vinylcarbazole) (PVKL): 40% 2-(4-Biphenyl)-5-(4-tert-butylphenyl)-1,2,4-oxadiazole (PBD): 8% Ir(ppy)₃. It was found that the PEDOT–PSS with the highest work function and resistivity produced the devices with the highest efficiencies; this is due to the improved hole injection effect, the decrease in electron leakage current and the prevention of pixel crosstalk. A maximum device current efficiency of 33.4 cd A⁻¹ has been achieved for the most resistive PEDOT; this corresponded to an external quantum efficiency (E.Q.E.) of 11%. Increasing the work function of the PEDOT used resulted in a 60% increase in E.Q.E. and device efficiency for PEDOTs in the same resistivity range. Drift–diffusion simulations, carried out using SEmiconducting Thin Film Optics Simulation software (SETFOS) 3.2, produced J–V curves in good agreement with the experimentally observed results; this allowed us to extract qualitative values for the effective device mobility along with the PEDOT work function and resistivity.