Synthesis of epoxy‐functionalized hyperbranched poly(phenylene oxide) and its modification of cyanate ester resin

High curing temperature is the key drawback of present heat resistant thermosetting resins. A novel epoxy‐functionalized hyperbranched poly(phenylene oxide), coded as eHBPPO, was synthesized, and used to modify 2,2′‐bis (4‐cyanatophenyl) isopropylidene (CE). Compared with CE, CE/eHBPPO system has significantly decreased curing temperature owing to the different curing mechanism. Based on this results, cured CE/eHBPPO resins without postcuring process, and cured CE resin postcured at 230°C were prepared, their dynamic mechanical and dielectric properties were systematically investigated. Results show that cured CE/eHBPPO resins not only have excellent stability in dielectric properties over a wide frequency range (1–10⁹Hz), but also show attractively lower dielectric constant and loss than CE resin. In addition, cured CE/eHBPPO resins also have high glass transition temperature and storage moduli in glassy state. These attractive integrated performance of CE/eHBPPO suggest a new method to develop high performance resins. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Blended hybrids based on silsesquioxane–OH and epoxy resins

Blended hybrids based on silsesquioxane cyclohexyl trisilanol [STOH; i.e., (c‐C₆H₁₁)₇Si₇O₉(OH)₃] and epoxy resin 4,5‐epoxyhexyl‐1,2‐dimethyl acid diglycidyl ester (TDE‐85) were prepared with good compatibility of STOH up to 5 wt % with TDE‐85. The blended hybrid resins, with various STOH additions, were cured by 4,4′‐diaminodiphenylsulfone, and the curing reactions were investigated with differential scanning calorimetry. The incorporation of STOH increased the curing reaction of TDE‐85 for three active hydrogens existing in the STOH molecule. The storage moduli and glass‐transition temperatures of the cured hybrid resins were studied with dynamic mechanical analysis. The cured hybrids had higher storage moduli than the pure epoxy resins at lower temperatures and increased slightly even when the temperature was above the glass‐transition temperature. Two peaks appearing in tan δ curves indicated the block copolymer structure and two different glass‐transition temperatures of the cured hybrid resins. The thermal stability and flame retardancy of the cured hybrid resins were investigated with thermogravimetric analysis and limited oxygen index values, respectively. The results showed that introducing silsesquioxane–OH units into epoxy resins could improve the thermal stability and flame retardancy of the resins. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Preparation,curing kinetics,and thermal properties of bisphenol fluorene epoxy resin

Diglycidyl ether of 9,9‐bis(4‐hydroxyphenyl) fluorene (DGEBF) was synthesized to introduce more aromatic structures into an epoxy resin system. The structure of DGEBF was characterized with Fourier transform infrared and ¹H‐NMR. 4,4′‐Diaminodiphenylmethane (DDM) was used as the curing agent for DGEBF, and differential scanning calorimetry was applied to study the curing kinetics. The glass‐transition temperature of the cured DGEBF/DDM, determined by dynamic mechanical analysis, was 260°C, which was about 100°C higher than that of widely used diglycidyl ether of bisphenol A (DGEBA). Thermogravimetric analysis was used to study the thermal degradation behavior of the cured DGEBF/DDM system: its onset degradation temperature was 370°C, and at 700°C, its char yield was about 27%, whereas that of cured DGEBA/DDM was only 14%. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and thermal properties of bismaleimide blends based on hydroxyphenyl maleimide

N‐(4‐hydroxyphenyl)maleimide was melt‐blended with the glycidyl ether of bisphenol‐A and various mole percentages of 4, 4′‐(diaminodiphenylsulfone) bismaleimide. The cure behaviour of the resins was evaluated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The blends showed distinct reductions in the onset of cure (T_o) and peak exothermic (T_exo) temperatures. The blends cured at low temperatures exhibited glass transition temperatures (T_gs) higher than the cure temperatures. The cured blends showed high moduli, glass transition temperatures in excess of 250 °C and good thermal stabilities up to 400 °C. Copyright © 2005 Society of Chemical Industry     

Synthesis and characterization of phthalonitrile resins from ortho‐linked aromatic and heterocyclic monomers

This article describes the synthesis and properties of phthalonitrile polymers prepared from three different ortho‐linked monomers, namely 2,2′‐bis(3,4‐dicyanophenoxy)biphenyl, 1,2‐bis(3,4‐dicyanophenoxy)benzene and 2,2′‐bis(3,4‐dicyanophenoxy)‐1,3,4‐oxadiazole. The resins exhibited a low complex viscosity, with a varying range of processing temperatures for all three systems. Thermogravimetric analysis showed that the synthesized polymers exhibited high thermal and thermo‐oxidative stability. The high char yields, which ranged from 64 to 69% at 900 °C under nitrogen atmosphere, and the high glass transition temperatures of the polymers indicated a high crosslinking density in the network structure. Dynamic mechanical measurements demonstrated that the fully cured monomer 2,2′‐bis(3,4‐dicyanophenoxy)‐1,3,4‐oxadiazole exhibited no change in glass transition temperature or in storage modulus up to 500 °C. © 2013 Society of Chemical Industry     

Comparative study of silicon‐containing cycloaliphatic epoxides between different chemical structures and curing mechanisms for potential light‐emitting diode encapsulation applications

The aim of this paper is to systematically investigate the curing behavior of three novel di‐ and trifunctional silicon‐containing cycloaliphatic epoxy resins by both anhydride and cationic ring‐opening polymerization methods as well as the viscoelasticity, thermal stability, water absorption and optical properties of the cured products. Differential scanning calorimetry curves show that, relative to anhydride curing, cationic polymerization can decrease the curing temperature to below 120 °C, and the reaction exothermic peaks become very narrow and sharp, exhibiting rapid curing characteristics at moderately low temperature. In addition, the differences between the anhydride and cationic curing methods bring about interesting variations in physical properties for the cured products which are well related to their chemical structures, polymerization mechanism, crosslinking density, segmental flexibility and inter‐segmental distance. The excellent transparency, rapid cationic curing rate, good thermal stability and high glass transition temperature of over 275 °C make this series of epoxy resins promising candidates for light‐emitting diode encapsulation applications. © 2012 Society of Chemical Industry     

Synthesis and characterization of melt‐processable polyimides derived from 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene

A series of molecular‐weight‐controlled imide resins end‐capped with phenylethynyl groups were prepared through the polycondensation of a mixture of 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene and 1,3‐bis(4‐aminophenoxy)benzene with 4,4′‐oxydiphthalic anhydride in the presence of 4‐phenylethynylphthalic anhydride as an end‐capping agent. The effects of the resin chemical structures and molecular weights on their melt processability and thermal properties were systematically investigated. The experimental results demonstrated that the molecular‐weight‐controlled imide resins exhibited not only meltability and melt stability but also low melt viscosity and high fluidability at temperatures lower than 280°C. The molecular‐weight‐controlled imide resins could be thermally cured at 371°C to yield thermoset polyimides by polymer chain extension and crosslinking. The neat thermoset polyimides showed excellent thermal stability, with an initial thermal decomposition temperature of more than 500°C and high glass‐transition temperatures greater than 290°C, and good mechanical properties, with flexural strengths in the range of 140.1–163.6 MPa, flexural moduli of 3.0–3.6 GPa, tensile strengths of 60.7–93.8 MPa, and elongations at break as high as 14.7%. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Copolymerization modification: improving the processability and thermal properties of phthalonitrile resins with novel comonomers

Two novel tetrahydrophthalic anhydride end‐capped imide compounds (THAN and THBN) with high thermal stability were synthesized to promote the curing reaction of 1,3‐bis(3,4‐dicyanophenoxy)benzene (3BOCN), and to study the effects of comonomer structure on the curing behavior and thermal performance of phthalonitrile resins. The curing behaviors of THAN/3BOCN and THBN/3BOCN blends with various molar ratios were investigated using rheological analysis and differential scanning calorimetry, suggesting a wide processing window. Dynamic mechanical analysis and thermogravimetric analysis showed that the cured resins possessed high glass transition temperatures (> 500 °C), and superior thermal and long‐term thermo‐oxidative stabilities with weight retention of 95% ranging from about 544 to 558 °C in both nitrogen and air. All these results indicated that the processability and thermal properties of phthalonitrile resins could be improved further by modifying the structure of comonomer in this kind of curing system. © 2018 Society of Chemical Industry     

Studies on crosslinking and thermal behavior of phthalonitrile end‐capped imide monomer in presence of aromatic amines

This paper describes the synthesis and characterization of a bisphthalonitrile monomer having an imide linkage prepared by reacting 4,4′‐(hexafluoroisopropylidene) diphthalic anhydride with 4‐(4‐aminophenoxy) phthalonitrile. The structure of the monomer was confirmed by Fourier transform infrared, ¹H‐NMR, and ¹³C‐NMR spectroscopy. The curing behavior of bisphthalonitrile monomer was investigated in the absence or presence of different diamines using differential scanning calorimetry. Diamines 4,4′‐diaminodiphenyl ether (DDE) and 4,4′‐diaminodiphenylsulfone (DDS) were used to investigate the effect of the structure of diamines on the curing behavior of bisphthalonitrile monomer. An exothermic transition due to curing was observed in the DSC scan, and the curing temperature was found to be dependent on the nucleophilicity of the amine. DDE was found to be more reactive than DDS. The thermal stability of the cured resins was evaluated using thermogravimetry in nitrogen atmosphere. All of the cured samples were stable up to 400 °C and leave behind 62% char residue at 800 °C, which was found to be dependent on the structure of the diamine used for curing as well as on the curing conditions. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46151.     

Branched phenyl‐s‐triazine moieties to enhance thermal properties of phthalonitrile thermosets

Heat‐resistant materials have made tremendous progress in marine, aerospace and microelectronic fields. Herein, a new class of phthalonitrile resins, branched poly(biphenyl ether triphenyl‐s‐triazine) phthalonitriles, were successfully synthesized via a two‐step, one‐pot reaction, on the basis of 2,4,6‐tris(4‐fluorophenyl)‐1,3,5‐triazine and 4,4′‐biphenol. 4,4′‐Diaminodiphenylsulfone was employed to facilitate the curing reaction, and successful realization of curing behavior was concluded from rheological and differential scanning calorimetric studies, indicating the obtained resins possess favorable processability. The relationship between concentration of reactants and properties of the resins was systematically studied. After thermal curing, the E‐glass fiber‐reinforced composite, prepared with a concentration of reactants of 0.15 g mL^?1, shows an admirable glass transition temperature of 480 °C and commendable thermal stability with 5% weight loss temperature in nitrogen of 563 °C, suggesting that the improvement of the thermal properties stems from the branched structure and the phenyl‐s‐triazine units. © 2017 Society of Chemical Industry     

Amino‐capped aniline trimer/epoxy resin intercrosslinked networks

An amino‐capped aniline trimer (ACAT) in emeraldine base form was reacted with an epoxy resin to produce intercrosslinked networks. The quinoid structure of the ACAT was able to crosslink on curing and, thus, led to a very high glass‐transition temperature of the cured resin. The epoxy resin cured with the ACAT showed superior thermal properties over the resins cured with p‐phenylenediamine and 4,4′‐diamino diphenylamine. These findings were based on differential scanning calorimetry, IR, dynamic mechanical analysis, and thermogravimetric analysis data. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 222–226, 2006     

Synthesis and characterization of epoxy film cured with phosphorous‐containing phenolic resin

Through the electrophilic addition reaction of ? P(O)? H and C?C, a series of novel phosphorus‐containing phenolic resins bearing maleimide (P‐PMFs) were synthesized and used as curing agent for preparing high performance and flame retardancy epoxy resins. The structure of the resin was confirmed with FTIR and elemental analysis. Thermal properties and thermal degradation behaviors of the thermosetted resin was investigated by using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The epoxy resins exhibited high glass transition temperature (143–156°C), goof thermal stability (>330°C) and retardation on thermal degradation rates. High char yields (700°C, 52.9%) and high limited oxygen indices (30.6–34.8) were observed, indicating the resins' good flame retardance for the P‐PMFs/CNE cured resins. The developed resin may be used potentially as environmentally preferable products in electronic fields. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3813–3817, 2007     

Effect of different aromatic amines on the crosslinking behavior and thermal properties of phthalonitrile oligomer containing biphenyl ethernitrile

To find a proper amine to promote the processability of phthalonitrile‐based composites, three different aromatic amines: 4‐aminophenoxyphthalonitrile (APN), 2,6‐bis (4‐diaminobenzoxy) benzonitrile (BDB) and 4,4′‐diaminediphenyl sulfone (DDS) were used as curing agents to investigate the crosslinking behavior and thermal decomposition behavior of phthalonitrile oligomer containing biphenyl ethernitrile (2PEN‐BPh). Differential scanning calorimeter (DSC) and dynamic rheological analysis were employed to study the curing reaction behavior of the phthalonitrile/amine blends and prepolymers. The studies revealed that BDB was the preferred curing agent and the preferred concentration of BDB was 3 wt %. The thermal properties of the 2PEN‐BPh polymers were monitored by TGA, and the results indicated that all the completely cured 2PEN‐BPh polymers maintained good structure integrity upon heating to elevated temperatures and these polymers could thermal stabilize up to over 550°C in both air and nitrogen atmospheres. Dynamic mechanical analysis (DMA) showed the glass transition temperature (T_g) exceeded 450°C when the 2PEN‐BPh polymer post cured at 375°C for 8 h. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Microwave processing of SiC nanoparticles infused polymer composites: Comparison of thermal and mechanical properties

The goal of this study is to compare thermal and mechanical properties of an epoxy resin system reinforced with SiC nanoparticles using both conventional thermal curing and microwave irradiation techniques. The microwave curing technique has shown potential benefits in processing polymeric nanocomposites by reducing the curing time without compromising the thermo‐mechanical performances of the materials. It was observed from this investigation that, the curing time was drastically reduced to ～30 min for microwave curing instead of 12 h room temperature curing with additional 6 h post curing at 75°C. Ductile behavior was more pronounced for microwave curing technique while thermal curing showed brittle like behavior as revealed from flexural test. The maximum strain to failure was increased by 25–40% for microwave‐cured nanocomposites over the room temperature cured nanocomposites for the same loading of nanofillers. The glass transition temperature (T_g) also increased by ～14°C while curing under microwave irradiation. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41708.     

High glass transition temperature bismaleimide‐triazine resins based on soluble amorphous bismaleimide monomer

A novel bismaleimide (DOPO‐BMI) with unsymmetrical chemical structure and DOPO pendant group has been prepared. The particular molecular structure makes DOPO‐BMI show an intrinsic amorphous state with a T_g about 135°C and excellent solubility in most organic solvents, which is beneficial to the processability of bismaleimide composite materials. A series of bismaleimide‐triazine (BT) resins have been prepared based on DOPO‐BMI and 2,2‐bis(4‐cyanatophenyl)propane at various weight ratios. The prepared BT resins show outstanding solubility in organic solvent and low viscosity about 10–671 mPa s at 180°C. The cured BT resins exhibit high glass transition temperature (T_g) over 316°C. As the weight ratio of DOPO‐BMI increases to 80% (BT80), the T_g can rise to 369°C (tan δ). The cured BT resins also show good thermal stability with the 5% weight loss temperature over 400°C under both nitrogen and air atmosphere. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42882.     

High‐performance hyperbranched poly(phenylene oxide) modified bismaleimide resin with high thermal stability,low dielectric constant and loss

High‐performance hyperbranched poly(phenylene oxide)‐modified bismaleimide resin with high thermal stability, low dielectric constant, and loss was developed, which is made up of hyperbranched poly(phenylene oxide) (HBPPO), 4,4′‐bismaleimidodiphenylmethane (BDM), and o, o′‐diallylbisphenol A (DBA). The curing reactivity, morphology, and performance of BDM/DBA/HBPPO resin were systemically investigated, and similar investigations for BDM/DBA resin were also carried out for comparison. Results show that BDM/DBA/HBPPO and BDM/DBA resins have similar curing mechanism, but the former can be cured at lower temperature than the later; in addition, cured BDM/DBA/HBPPO resin with suitable HBPPO content has better thermal stability and dielectric properties (lower dielectric constant and loss) than BDM/DBA resin. The difference in macroproperties between BDM/DBA/HBPPO and BDM/DBA resins results from the different chemical structures and morphologies of their crosslinking networks. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Catalytic effect of 2,2′‐diallyl bisphenol A on thermal curing of cyanate esters

Cyanate esters are a class of thermal resistant polymers widely used as thermal resistant and electrical insulating materials for electric devices and structural composite applications. In this article, the effect of 2,2′‐diallyl bisphenol A (DBA) on catalyzing the thermal curing of cyanate ester resins was studied. The curing behavior, thermal resistance, and thermal mechanical properties of these DBA catalyzed cyanate ester resins were characterized. The results show that DBA is especially suitable for catalyzing the polymerization of the novolac cyanate ester resin (HF‐5), as it acts as both the curing catalyst through depressing the exothermic peak temperature (T_exo) by nearly 100°C and the toughening agent of the novolac cyanate ester resin by slightly reducing the elastic modulus at the glassy state. The thermogravimetric analysis and dynamic mechanical thermal analysis show that the 5 wt % DBA‐catalyzed novolac cyanate ester resin exhibits good thermal resistance with T_d⁵ of 410°C and the char yield at 900°C of 58% and can retain its mechanical strength up to 250°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1775–1786, 2006     

Dielectric behavior and properties of a cyanate ester containing dicyclopentadiene. I

2,6‐Dimethyl phenol dicyclopentadiene dicyanate ester (DCPDCY) was synthesized through the reaction of 2,6‐dimethyl phenol dicyclopentadiene novolac and cyanogen bromide. The proposed structure was confirmed by Fourier transform infrared, mass spectrometry, NMR spectrometry, and elemental analysis. DCPDCY was then cured by itself or cured with bisphenol A dicyanate ester (BADCY) to form triazine structures. The thermal properties of the cured DCPDCY resins were studied with differential scanning calorimetry, dynamic mechanical analysis (DMA), dielectric analysis, and thermogravimetric analysis; these data were compared with those of BADCY. The cured DCPDCY resins exhibited a lower dielectric constant (2.58 at 1 MHz), a lower dissipation factor (20.2 mU at 1 MHz), less thermal stability (the 5% degradation temperature and char yield were 430°C and 32.1%, respectively), a lower glass‐transition temperature (266°C by thermomechanical analysis and 271°C by DMA), a lower coefficient of thermal expansion (22.5 ppm before the glass‐transition temperature and 124.9 ppm after the glass‐transition temperature), and less moisture absorption (0.88% at 48 h) than BADCY, but they showed higher moduli (6.28 GPa at 150°C and 5.35 GPa at 150°C) than the bisphenol A system. The properties of the cured cocyanate esters (DCPDCY and BADCY) lay between those of cured BADCY and DCPDCY, except for the moduli. The moduli of some cocyanate esters were even higher than those of cured BADCY and DCPDCY. A positive deviation from the Fox equation was observed for cocyanate esters. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2079–2089, 2005     

Synthesis and properties of fluorinated biphenyl‐type epoxy resin

A novel fluorinated biphenyl‐type epoxy resin (FBE) was synthesized by epoxidation of a fluorinated biphenyl‐type phenolic resin, which was prepared by the condensation of 3‐trifluoromethylphenol and 4,4′‐bismethoxymethylbiphenyl catalyzed in the presence of strong Lewis acid. Resin blends mixed by FBE with phenolic resin as curing agent showed low melt viscosity (1.3–2.5 Pa s) at 120–122°C. Experimental results indicated that the cured fluorinated epoxy resins possess good thermal stability with 5% weight loss under 409–415°C, high glass‐transition temperature of 139–151°C (determined by dynamic mechanical analysis), and outstanding mechanical properties with flexural strength of 117–121 MPa as well as tensile strength of 71–72 MPa. The thermally cured fluorinated biphenyl‐type epoxy resin also showed good electrical insulation properties with volume resistivity of 0.5–0.8 × 10¹⁷ Ω cm and surface resistivity of 0.8–4.6 × 10¹⁶ Ω. The measured dielectric constants at 1 MHz were in the range of 3.8–4.1 and the measured dielectric dissipation factors (tan δ) were in the range of 3.6–3.8 × 10^?3. It was found that the fluorinated epoxy resins have improved dielectric properties, lower moisture adsorption, as well as better flame‐retardant properties compared with the corresponding commercial biphenyl‐type epoxy resins. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Phosphorous‐containing epoxy resins from a novel synthesis route

The ? P(O)‐H in 9,10‐dihydro‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) was used as an active group to react with the carbonyl group in 4,4′‐dihydroxybenzophenone (DHBP) to result a novel phosphorous‐containing biphenol compound (DOPO‐2OH). Phosphorous‐containing epoxy resins were therefore obtained from reacting DOPO‐2OH with epichlorohydrin or with diglycidylether bisphenol A. The synthesized compounds were characterized with FTIR, ¹H and ³¹P NMR, elemental analysis, and epoxide equivalent weight titration to demonstrate the their chemical structures. Cured epoxy resins were prepared via thermal curing the epoxy resins with various curing agents. Thermal analysis results (differential scanning calorimetry and thermogravimetric analysis) revealed that these cured epoxy resins exhibited high glass transition temperatures and high thermal stability. High char yields at 700°C and high LOI (limited oxygen index) values were also found for the cured epoxy resins to imply that the resins were possessing high flame retardancy. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1697–1701, 2002