Internal Oxidation of Ce3+-BaTiO3 Solid Solutions

The reoxidation process in highly Ce³⁺-doped BaTiO₃ ceramics was studied using TEM. Samples of two different types of solid solutions, Ba_1−XCe³⁺ _X Ti_1−X/4( V _Ti) X/4 O₃ and Ba_1−XCe³⁺ _X Ti⁴⁺_{1− X} Ti³⁺ _X O₃, were prepared by sintering oxide mixtures in air and in a reducing atmosphere, respectively. The solid solutions were reoxidized by annealing in air at high temperatures (1000°—1100°C). As a result of internal oxidation of Ce³⁺ and Ti³⁺, fluorite CeO₂ and monoclinic Ba₆Ti₁₇O₄₀ phases were precipitated in the perovskite matrix. In Ba_1−XCe³⁺ _X Ti_1−X/4( V _Ti)X/4O3 solid solution precipitates nucleate heterogeneously at grain boundaries and at extended defects inside the grains, whereas in Ba_1−XCe³⁺_XTi⁴⁺_1−XTi³⁺_XO₃ solid solution precipitates are nucleated mainly homogeneously inside reoxidized perovskite grains. The form of the precipitates and their orientational relationship with the matrix, as well as the mechanism of internal oxidation, are discussed.     

Bismuth/Samarium Cosubstituted Ba6−3xNd8+2xTi18O54 Microwave Dielectric Ceramics

Modification of the microwave dielectric properties in Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ ( x = 0.5) solid solutions by Bi/Sm cosubstitution for Nd was investigated. A large increase in the dielectric constant and near-zero temperature coefficient combined with high Qf values were obtained in modified Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ solid solutions where an enlarged solid solution limit of Bi in Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ was observed. Excellent microwave dielectric characteristics (ɛ= 105, Qf = 4110 GHz, and very low τ_f) were achieved in the composition Ba_{6−3 x} (Nd_0.7Bi_0.18Sm_0.12)_{8+2 x} Ti₁₈O₅₄.     

Electrical Properties of a Bismuth Layer-Structured Ba2Bi4Ti5O18 Single Crystal

Ba₂Bi₄Ti₅O₁₈ single crystals were grown, and their dielectric permittivity, conductivity, and ferroelectricity were investigated along the a -(or b -)axis and the c -axis separately. The dielectric permittivity at 1 MHz along the a -(or b -)axis was 2000 at the Curie temperature (360°C); this value was 8 times greater than that along the c -axis. The dc conductivity was greater along the a -(or b -)axis than that along the c -axis, by one order of magnitude. In regard to the ferroelectricity, the saturated remanent polarization was 120 mC/m² and the saturated coercive field was 3 MV/m along the a -(or b -)axis; values of 8.5 mC/m² and 0.81 MV/m, respectively, were observed along the c -axis. The Ba₂Bi₄Ti₅O₁₈ single crystals had large electrical anisotropies, which were due to the layered structure.     

Diffuse Ferroelectric Phase Transition and Relaxor Behaviors in Ba-Based Bismuth Layer-Structured Compounds and La-Substituted SrBi4Ti4O15

The dielectric characteristics of BaBi₂Nb₂O₉, BaBi₄Ti₄O₁₅, BaBi₈Ti₇O₂₇, and La-substituted SrBi₄Ti₄O₄ were investigated to discuss their ferroelectric phase transition and relaxor behaviors. BaBi₂Nb₂O₉ showed typical relaxor behaviors, and a shift of T _m with increasing frequency was observed in BaBi₄Ti₄O₁₅ and SrBi_{4− x} La _x Ti₄O₁₅ ( x =0.8, 1.0) but they underwent a real paraelectric–ferroelectric phase transition on zero-field cooling, while BaBi₈Ti₇O₂₇ showed a normal ferroelectric nature. The reduced concentration and weakened coupling of the dipoles related to A-site bismuth are believed to be responsible for the appearance of short-range electric ordering and the relaxor behaviors in these bismuth layer-structured compounds.     

Microstructural Changes during the Reduction/Reoxidation Process in Donor-Doped BaTiO3 Ceramics

Microstructural changes occurring during oxidation of the reduced form of donor-doped BaTiO₃ (Ba_{1− X} D _X ^.Ti_{1− X} ⁴⁺Ti _X ³⁺O₃) and during reduction of the oxidized form of donor-doped BaTiO₃ (Ba_{1− X} D _X ^.Ti_{1− X /4}⁴⁺( V _Ti^) _{X /4}O₃) were studied using TEM. Samples of both types of solid solutions, containing different La concentrations (from 2 to 20 mol% La), were prepared by sintering under reducing conditions and in air, respectively. The reduced form of donor-doped BaTiO₃ was oxidized by annealing at high temperatures (1150° and 1350°C) in air, while the oxidized form was reduced by annealing under reducing conditions. Because of oxidation of the reduced phase of donor-doped BaTiO₃, the Ti-rich phases Ba₆Ti₁₇O₄₀ and BaLa₂Ti₄O₁₂ were precipitated. Reduction of the oxidized form caused precipitation of the Ba-rich phase Ba₂TiO₄ preferentially inside the matrix grains. All precipitates had well-defined orientational relationships with the perovskite matrix.     

Subsolidus Phase Equilibria in the System Na2O-Bi2O3-TiO2 at 1000°C

Subsolidus phase relations in the system Na₂O-Bi₂O₃-TiO₂ at 1000°C were investigated by solid-state reaction techniques and X-ray diffraction methods. Five ternary compounds were observed in the system: Na_0.5Bi_4.5Ti₄O₁₅; Na_0.5Bi_0.5TiO₃; a cubic pyrochlore solid solution composed of xNa₂O.25Bi₂O₃.(75−;x) TiO₂ where x is 2.5 to 3.75; a new compound Na_0.5Bi_8.5Ti₇O₂₇ indexed with the orthorhombic cell of a = 5.45, b = 5.42, and c = 36.8 Å; and an unidentified phase with the probable composition NaBiTi₆O₁₄.     

Effects of B2O3 on the Phase Stability of Ba2Ti9O20 Microwave Ceramic

Preparation of dense and phase-pure Ba₂Ti₉O₂₀ is generally difficult using solid-state reaction, since there are several thermodynamically stable compounds in the vicinity of the desired composition and a curvature of Ba₂Ti₉O₂₀ equilibrium phase boundary in the BaO–TiO₂ system at high temperatures. In this study, the effects of B₂O₃ on the densification, microstructural evolution, and phase stability of Ba₂Ti₉O₂₀ were investigated. It was found that the densification of Ba₂Ti₉O₂₀ sintered with B₂O₃ was promoted by the transient liquid phase formed at 840°C. At sintering temperatures higher than 1100°C, the solid-state sintering became dominant because of the evaporation of B₂O₃. With the addition of 5 wt% B₂O₃, the ceramic yielded a pure Ba₂Ti₉O₂₀ phase at sintering temperatures as low as 900°C, without any solid solution additive such as SnO₂ or ZrO₂. The facilities of B₂O₃ addition to the stability of Ba₂Ti₉O₂₀ are apparently due to the eutectic liquid phase which accelerates the migration of reactant species.     

Topochemical Synthesis of Plate-Like Na0.5Bi0.5TiO3 from Aurivillius Precursor

Plate-like Na_0.5Bi_0.5TiO₃ (NBT) particles with perovskite structure were synthesized by topochemical microcrystal conversion from plate-like particles of layer-structured Na_0.5Bi_4.5Ti₄O₁₅ (NBIT) at 950°C in NaCl molten salt. As the precursors of NBT, plate-like NBIT particles were first synthesized by molten salt process by the reaction of Bi₄Ti₃O₁₂, Na₂CO₃, and TiO₂. After the topochemical reactions, layer-structured NBIT particles were transformed to the perovskite NBT platelets. NBT particles with a thickness of approximately 0.5 μm and a length of 10–15 μm retained the morphology feature of the precursor. High-aspect-ratio NBT platelets are suitable templates to obtain textured ceramics (especially NBT-based ceramics) by (reactive) template grain growth process.     

Comment on "Effect of Al2O3 and Bi2O3 on the Formation Mechanism of Sn-Doped Ba2Ti9O20"

in a recent article of the Journal , Yu et al .¹ reported their experimental results on the effect of Al₂O₃ and Bi₂O₃ on the formation mechanism of Sn-doped Ba₂Ti₉O₂₀. They claimed that both Al₂O₃ and Bi₂O₃ can dramatically assist the formation of Sn-doped Ba₂Ti₉O₂₀ but are based on different mechanisms. They concluded that first, Bi₂O₃ melts above 830°C and accelerates the migration of the involved reactants to form Ba₂Ti₉O₂₀; second, Al₂O₃ can reduce the height of the potential energy barrier of the formation of Ba₂Ti₉O₂₀ due to the intergrowth of BaAl₂Ti₆O₁₆ phase. They explained their results from a point of view that the formation of Ba₂Ti₉O₂₀ is controlled by (1) the migration of reactants to the interfaces and (2) the height of the potential-energy barrier of the reaction at the interfaces. However, based on their results, we feel their conclusions are incautious and may be misleading, as will be discussed later.     

Phase Equilibria in the TiO2-Rich Region of the System BaO-TiO2

Phase relations in the system BaO-TiO₂ from 67 to 100 mol% TiO₂ were investigated at 1200° to 1450°C in O₂. Data were obtained by microstructural, X-ray, and thermal analyses. The existence of the stable compounds Ba₆Ti₁₇O₄₀, Ba₄Ti₁₃O₃₀, BaTi₄O₉, and Ba₂Ti₉O₂₀ was confirmed. The compound BaTi₂O₅ is unstable and either forms as a reaction intermediate below the solidus or crystallizes from the melt. The compounds Ba₆Ti₁₇O₄₀ and Ba₄Ti₁₃O₃₀ decompose in peritectic reactions, and BaTiO₃ and Ba₆Ti₁₇O₄₀ react to form a eutectic. Special conditions are required for the formation of Ba₂Ti₉O₂₀, which decomposes in a peritectoid reaction at 1420°C. The new phase diagram is presented.     

Sol–Gel Preparation of BaTi4O9 and Ba2Ti9O20

BaTi₄O₉ and Ba₂Ti₉O₂₀ precursors were prepared via a sol–gel method, using ethylenediaminetetraacetic acid as a chelating agent. The sol–gel precursors were heated at 700°–1200°C in air, and X-ray diffractometry (XRD) was used to determine the phase transformations as a function of temperature. Single-phase BaTi₄O₉ could not be obtained, even after heating the precursors at 1200°C for 2 h, whereas single-phase Ba₂Ti₉O₂₀ (as determined via XRD) was obtained at 1200°C for 2 h. Details of the synthesis and characterization of the resultant products have been given.     

Preparation and Unit-Cell Parameters of Single Crystals of Ba2Ti9020

Ba₂Ti₉O₂₀ crystallizes in the monoclinic system with α= l.4818(5) nm, b = 1.4283(6), and c = 0.7109(2) with β = 98.37°±0.07°. The most likely space group is P 2₁/ m , Z = 4 with a calculated density 4.58 g/cm³. The powder pattern was indexed. The Ba₂Ti₉O₂₀ crystals form as stellated groups when melts of BaCl₂+ 20 to 50% TiO₂ cool from 1275°C.     

Synthesis of Micron-Scale Platelet BaTiO3

Micron-scale platelet barium titanate was synthesized using a twostep molten salt and topochemical technique. Plate-like BaBi₄Ti₄O₁₅ was first synthesized as a precursor by molten salt synthesis. Then, Bi³⁺ in the precursor was replaced by Ba²⁺ and formed perovskite-structure BaTiO₃ through a topochemical reaction. The BaTiO₃ single crystals have an average size of 5–10 μm and a thickness of 0.5 μm. The purpose of this article is to control the particle shape with desired structure. High aspect ratio BaTiO₃ platelets are suitable templates to obtain textured ceramics (especially Pb(Mg_1/3Nb_2/3)O₃–32.5PbTiO₃) by the templated grain growth process.     

Microwave Properties of Ba2Ti9O20 Doped with Zirconium and Tin Oxides

The effects of solid-solution additives, their concentration, and the thermal processing schedule on the microstructure evolution and microwave properties of Ba₂Ti₉O₂₀ were studied. The solubility of tin in Ba₂Ti₉O₂₀ was higher than that of zirconium. Both elements facilitated the formation of phase-pure Ba₂Ti₉O₂₀ resonators. Ba₂Ti₉O₂₀ formed most easily with low dopant concentrations (0.82 mol%) (most impressively for ZrO₂ substitutions). Extended heat treatment (16 h versus 6 h at a temperature of 1390°C) resulted in volatilization of the grain-boundary liquid phase, which leads to more-porous resonators that have correspondingly lower permittivities. Increasing the dopant concentration resulted in minor increases in the quality factor; doping with zirconium led to slightly higher values (a maximum of 13900 at a frequency of 3 GHz). Increasing the measurement temperature degraded the quality factor (most precipitously for BaTi₄O₉). The temperature coefficient decreased as the ZrO₂ substitution increased but was largely unaffected by the SnO₂ concentration. Excess TiO₂ in a batch with no other dopants demonstrated degraded microwave properties.     

Effect of Al2O3 and Bi2O3 on the Formation Mechanism of Sn-Doped Ba2Ti9O20

High-performance Ba₂Ti₉O₂₀ ceramics are attracting great attention, but their formation mechanism still is somewhat unclear. The present investigation shows that the formation of Ba₂Ti₉O₂₀ can be promoted strikingly by the participation of Bi₂O₃ and Al₂O₃. The effect of Bi₂O₃ on the formation of Ba₂Ti₉O₂₀ is attributed to the fact that migration of the involved reactants is accelerated by liquid which forms from the melting of Bi₂O₃ above 830°C. This migration, however, is not the only rate-limiting factor. A high potential-energy barrier, resulting from stress that arises along the crystal-structured layers, also heavily restricts the formation of Ba₂Ti₉O₂₀. The participation of Al₂O₃, on the other hand, can reduce the height of this potential-energy barrier and effectively improve the kinetics of the formation of Ba₂Ti₉O₂₀ by causing the formation of BaAI₂Ti₆O₁₆ crystals; these crystals intergrow with Ba₂Ti₉O₂₀ crystals and result in decreased stress.     

Factors Affecting the Formation of Ba2Ti9O20

The phase development sequence based on a composition equivalent to Ba₂Ti₉O₂₀ during heating is found to be in the following order: BaTi₅O₁₁ > BaTi₄O₉ > Ba₂Ti₉O₂₀. The lowest rate of formation of Ba₂Ti₉O₂₀ is caused by its high surface energy and interface energy, which result in a low nucleation rate. The existence of BaTi₅O₁₁ in calcined powder helps to form Ba₂Ti₉O₂₀ in sintered compacts. The effect of BaTi₅O₁₁ on Ba₂Ti₉O₂₀ formation can be explained by their similar oxygen packing and by reduced volume change during transformation. The amount of BaTi₅O₁₁ formed during heating depends greatly on the compositional homogeneity of powders. The addition of SnO₂ aids the formation of Ba₂Ti₉O₂₀ by reduced strain energy at transformation and reduced surface energy.     

Barium Neodymium Titanate Electroceramics: Phase Equilibria Studies of Ba6–3xNd8+2xTi18O54 Solid Solution

A solid-solution phase with the general formula Ba_6-3x Nd_8+2x Ti₁₈O₅₄, where 0.25(5) ≤×≤ 0.75(5), has been characterized at 1250°C; this phase has been variously described as BaNd₂Ti₄O₁₂ and BaNd₂Ti₅O₁₄ in the literature. Variation in its stoichiometry is accommodated via the cation substitution mechanism, 3Ba²⇆2Nd³⁺. The location and extent of the solid solution were demonstrated by a combination of phase diagram studies and X-ray diffraction techniques, including lattice parameter measurements and electron microscopy. A combination of techniques was employed due to the insensitivity of secondary phase detection by X-ray diffraction in this system. Using this approach, a second possible solid-solution mechanism, Ba²⁺2Nd³⁺⇆2Ti⁴⁺, is discounted.     

Photoluminescence Enhancement of (La0.95Eu0.05)2Ti2O7 Nanophosphors via Li+ Doping

Li⁺ ions have been successfully doped into the La sites of (La_0.95Eu_0.05)₂Ti₂O₇ nanocrystals through a facile citric acid sol–gel method. The doping concentration of Li⁺ ions can be as high as 15 mol%. Photoluminescence (PL) performances of the obtained samples have been investigated. The results showed that a doping with small number of Li⁺ ions improves the PL intensity of the synthesized La₂Ti₂O₇:Eu³⁺ nanophosphors. The highest emission intensity was observed using the formula of (La_0.92Eu_0.05Li_0.03)₂Ti₂O₇, whose brightness was increased by almost 20% in comparison with that of (La_0.95Eu_0.05)₂Ti₂O₇.     

Atmospheric Dependence on Dielectric Loss of 1/6Ba5Nb4O15· 5/6BaNb2O6 Ceramics

Samples of 1/6Ba₅Nb₄O₁₅·5/6BaNb₂O₆ along with the pure end members, Ba₅Nb₄O₁₅ and BaNb₂O₆, were sintered under low oxygen partial pressure. The degradation mechanisms of dielectric loss in this reducing atmosphere have been studied. We found that the degradation occurred primarily due to the formation of oxygen vacancies caused by the reduction of Nb⁵⁺. This was determined by measuring the electrical conductivity, and through X-ray photoelectron spectroscopy. More importantly, the dielectric loss of 1/6Ba₅Nb₄O₁₅·5/6BaNb₂O₆ samples with higher temperature stability was further decreased on sintering in a reducing atmosphere. This observation has been explained by considering the increased porosity and formation of a reduced second phase, Ba_0.65NbO₃.     

Preparation of Ba6−3xNd8+2xTi18O54 via Ethylenediaminetetraacetic Acid Precursor

Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ ceramic powders were synthesized by the modified Pechini method using ethylenediaminetetraacetic acid (EDTA) as a chelating agent. A purplish red, molecular-level, homogeneously mixed gel was prepared, and transferred into a porous resin intermediate through charring. Single-phase and well-crystallized Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ powders were obtained from pulverized resin at a temperature of 900°C for 3 h, without formation of any intermediate phases. Meanwhile, the molar ratio of EDTA to total metal cation concentration had a significant influence on the crystallization behavior of Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄. The Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ ( x = 2/3) ceramics prepared via EDTA precursor have excellent microwave dielectric characteristics: ɛ= 87, Qf = 8710 GHz.