Regenerated cellulose fibers as impact modifier in long jute fiber reinforced polypropylene composites: Effect on mechanical properties,morphology, and fiber breakage

Polypropylene/jute fiber (PP‐J) composites with various concentrations of viscose fibers (VF) as impact modifiers and maleated polypropylene (MAPP) as a compatibilizer have been studied. The composite materials were manufactured using direct long fiber thermoplastic (D‐LFT) extrusion and compression molding. The effect of fiber length, after the extrusion process, on composites mechanical performance and toughness was investigated. The results showed that the incorporation of soft and tough VF on the PP‐J improved the energy absorption of the composites. The higher impact strength was found with the addition of 10 wt % of the impact modifier, but the increased concentration of the impact modifier affected the tensile and flexural properties negatively. Similarly, HDT values were reduced with addition of viscose fibers whereas the addition of 2 wt % of maleated polypropylene significantly improved the overall composite properties. The microscopic analysis clearly demonstrated longer fiber pullouts on the optimized impact modified composite. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41301.     

Investigating polypropylene–green coconut fiber composites in the molten and solid states through various techniques

A series of polypropylene (PP)–green coconut fiber (GCF) composites were prepared by melt mixing and their properties studied in the molten state using an advanced nonlinear harmonic testing technique, and in the solid state using standard mechanical testing and scanning electron microscopy (SEM). The effect of fiber loading as well as the role of maleated polypropylene as compatibilizing agent was investigated. PP–GCF composites are heterogeneous materials that, in the molten state, are found to exhibit essentially a nonlinear viscoelastic character, in contrast with the pure PP, which has a linear viscoelastic region up to 50–60% strain. Complex modulus increases with GCF content but in such a manner that the observed reinforcement is at best of hydrodynamic origin, without any specific chemical interaction occurring between the polymer matrix and the fibers. The addition of maleated polypropylene improves the wetting of fibers by the molten polymer but the effect is so small that specific chemical reactions could hardly be considered as occurring. Flexural modulus data confirm the reinforcing effects of the fiber and an improvement is noted when some maleated polypropylene is used, with an optimum level of around 1% (or the PP content). SEM microphotographs clearly show that maleated polypropylene imparts a better wetting of GC fibers by PP, but chemical interactions are unlikely to occur between the polymer and GCF. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1922–1936, 2006     

Deformation mechanisms and mechanical properties of modified polypropylene/wood fiber composites

Mechanical properties and deformation mechanisms of polypropylene (PP)/wood fiber (WFb) composites modified with maleated polypropylene as compatibilizer and styrene-butadiene rubber (SBR) as impact modifier have been studied. The addition of maleated polypropylene to the unmodified polypropylene/wood fiber composite enhances the tensile modulus and yield stress as well as the Charpy impact strength. SBR does not cause a drop in the tensile modulus and yield strength because of the interplay between decreasing stiffness and strength by rubber modification and increasing stiffness and strength by good interfacial adhesion between the matrix and fibers. The addition of both maleated polypropylene and rubber to the polypropylene/wood fiber composite does not result in an improvement of effects based on maleated polypropylene and rubber, which includes possible synergism. The deformation mechanisms in unmodified polypropylene/wood fiber composite are matrix brittle fracture, fiber debonding and pullout. A polymeric layer around the fibers created from maleated polypropylene may undergo debonding, initiating local plasticity. Rubber particle cavitation, fiber pullout and debonding were the basic failure mechanisms of rubber-toughened polypropylene/wood fiber composite. When maleated polypropylene was added to this composite, fiber breakage and matrix plastic deformation took place. Polym. Compos. 25:521–526, 2004. © 2004 Society of Plastics Engineers.     

Effect of coupling agents on the thermal and mechanical properties of polypropylene–jute fabric composites

Composites with different jute fabric contents and polypropylene (PP) were prepared by compression molding. The composite tensile modulus increased as the fiber content increased, although the strain at break decreased due to the restriction imposed on the deformation of the matrix by the rigid fibers. Moreover, and despite the chemical incompatibility between the polar fiber and the PP matrix, the tensile strength increased with jute content because of the use of long woven fibers. The interfacial adhesion between jute and PP was improved by the addition of different commercial maleated polypropylenes to the neat PP matrix. The effect of these coupling agents on the interface properties was inferred from the resulting composite mechanical properties. Out‐of‐plane instrumented falling weight impact tests showed that compatibilized composites had lower propagation energy than uncompatibilized ones, which was a clear indication that the adhesion between matrix and fibers was better in the former case since fewer mechanisms of energy propagation were activated. These results are in agreement with those found in tensile tests, inasmuch as the compatibilized composites exhibit the highest tensile strength. Scanning electron microscopy also revealed that the compatibilized composites exhibited less fiber pullout and smoother fiber surface than uncompatibilized ones. The thermal behavior of PP–compatibilizer blends was also analyzed using differential scanning calorimetry, to confirm that the improvements in the mechanical properties were the result of the improved adhesion between both faces and not due to changes in the crystallinity of the matrix. Copyright © 2006 Society of Chemical Industry     

Preparation and performance characteristics of short‐glass‐fiber/maleated styrene–ethylene–butylene–styrene/polypropylene hybrid composites

Eighty/twenty polypropylene (PP)/styrene–ethylene–butylene–styrene (SEBS) and 80/20 PP/maleated styrene–ethylene–butylene–styrene (SEBS‐g‐MA) blends reinforced with 30 wt % short glass fibers (SGFs) were prepared by extrusion and subsequent injection molding. The influence of the maleic anhydride (MA) functional group grafted to SEBS on the properties of SGF/SEBS/PP hybrid composites was studied. Tensile and impact tests showed that the SEBS‐g‐MA copolymer improved the yield strength and impact toughness of the hybrid composites. Extensive plastic deformation occurred at the matrix interface layer next to the fibers of the SGF/SEBS‐g‐MA/PP composites during impact testing. This was attributed to the MA functional group, which enhanced the adhesion between SEBS and SGF. Differential scanning calorimetry measurements indicated that SEBS promoted the crystallization of PP spherulites by acting as active nucleation sites. However, the MA functional group grafted to SEBS retarded the crystallization of PP. Finally, polarized optical microscopy observations confirmed the absence of transcrystallinity at the glass‐fiber surfaces of both SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrid composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1303–1311, 2002     

Composition,tensile properties,and dispersion of polypropylene composites reinforced with viscose fibers

The reinforcement mechanics of viscose‐fiber‐reinforced polypropylene (PP) composites were studied. The effect of the coupling agent, maleated polypropylene (MAPP), was of special interest. The fibers, coupling agent, and PP were extruded and injection‐molded. The composition, mechanical properties, fracture morphology, and dispersion of the composites were examined. Thermogravimetric analysis showed that the fiber content in the tensile specimens varied slightly with the sample location; however, the differences in the values were within 1.0%. Scanning electron microscopy images of the fracture surfaces of the composites showed that the surfaces of the composites without MAPP were covered with fibers pulled out from the matrix. A lack of adhesion further appeared as a cracked matrix–fiber interface. A new scanning thermal microscopy method, microthermal analysis, was used to study the dispersion of the fibers in the composites. Local thermal analyses gave further information about the location of the fibers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2676–2684, 2004     

Long jute fiber‐reinforced polypropylene composite: Effects of jute fiber bundle and glass fiber hybridization

Two types of long jute fiber pellet consisting of twisted‐jute yarn (LFT‐JF/PP) and untwisted‐jute yarn (UT‐JF/PP) pellets are used to prepare jute fiber–reinforced polypropylene (JF/PP) composites. The mechanical properties of both long fiber composites are compared with that of re‐pelletized pellet (RP‐JF/PP) of LFT‐JF/PP pellet, which is re‐compounded by extrusion compounding. High stiffness and high impact strength of JF/PP composites are as a result of using long fiber. However, the longer fiber bundle consequently affects the distribution of jute fiber. The incorporation of 10 wt % glass fibers is found to improve mechanical properties of JF/PP composites. Increasing mechanical properties of hybrid composites is dependent on the type of JF/PP pellets, which directly affect the fiber length and fiber orientation of glass fiber within hybrid composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41819.     

Mechanical properties and morphology of impact modified polypropylene–wood flour composites

The mechanical properties and morphology of polypropylene/wood flour (PP/WF) composites with different impact modifiers and maleated polypropylene (MAPP) as a compatibilizer have been studied. Two different ethylene/propylene/diene terpolymers (EPDM) and one maleated styrene–ethylene/butylene–styrene triblock copolymer (SEBS–MA) have been used as impact modifiers in the PP/WF systems. All three elastomers increased the impact strength of the PP/WF composites but the addition of maleated EPDM and SEBS gave the greatest improvements in impact strength. Addition of MAPP did not affect the impact properties of the composites but had a positive effect on the composite unnotched impact strength when used together with elastomers. Tensile tests showed that MAPP had a negative effect on the elongation at break and a positive effect on tensile strength. The impact modifiers were found to decrease the stiffness of the composites. Scanning electron microscopy showed that maleated EPDM and SEBS had a stronger affinity for the wood surfaces than did the unmodified EPDM. The maleated elastomers are, therefore, expected to form a flexible interphase around the wood particles giving the composites better impact strength. MAPP further enhanced adhesion between WF and impact-modified PP systems. EPDM and EPDM–MA rubber domains were homogeneously dispersed in the PP matrix, the diameter of domains being between 0.1–1 μm. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:1503–1513, 1998     

Effects of alkali and silane treatment on the mechanical properties of jute‐fiber‐reinforced recycled polypropylene composites

Jute‐fibers‐reinforced thermoplastic composites are widely used in the automobile, packaging, and electronic industries because of their various advantages such as low cost, ease of recycling, and biodegradability. However, the applications of these kinds of composites are limited because of their unsatisfactory mechanical properties, which are caused by the poor interfacial compatibility between jute fibers and the thermoplastic matrix. In this work, four methods, including (i) alkali treatment, (ii) alkali and silane treatment, (iii) alkali and (maleic anhydride)‐polypropylene (MAPP) treatment, and (iv) alkali, silane, and MAPP treatment (ASMT) were used to treat jute fibers and improve the interfacial adhesion of jute‐fiber‐reinforced recycled polypropylene composites (JRPCS). The mechanical properties and impact fracture surfaces of the composites were observed, and their fracture mechanism was analyzed. The results showed that ASMT composites possessed the optimum comprehensive mechanical properties. When the weight fraction of jute fibers was 15%, the tensile strength and impact toughness were increased by 46 and 36%, respectively, compared to those of untreated composites. The strongest interfacial adhesion between jute fibers and recycled polypropylene was obtained for ASMT composites. The fracture styles of this kind of composite included fiber breakage, fiber pull‐out, and interfacial debonding. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers.     

Study on depositing SiO2 nanoparticles on the surface of jute fiber via hydrothermal method and its reinforced polypropylene composites

To improve the interfacial compatibility of jute fiber reinforced polypropylene (PP) composites, hydrothermal method was used to deposit SiO₂ nanoparticles on the surface of pretreated jute fibers and the effect of reaction factors (tetraethoxysilane [TEOS] concentration, ammonia concentration, and reaction temperature) on the deposition of SiO₂ nanoparticles were evaluated. The results of FTIR, XRD, SEM, and TEM showed that the amorphous SiO₂ nanoparticles with an average particle size of 65.0 nm were successfully deposited on the surface of jute fibers at the TEOS/H₂O volume ratio of 1:2, ammonia of 0.55 M, reaction temperature of 100 °C (0.15 MPa) for 5 h. Compared with the sol–gel method, SiO₂ nanoparticles obtained by the hydrothermal method possessed smaller particle size and were less agglomerated, which can better fill in the surface defects of the jute fibers and result in a 12.9% increase in the tensile strength. The study on the mechanical properties and interface performance of the jute fiber reinforced PP composites indicated that the interfacial compatibility between jute fibers and PP was obviously improved. The tensile and impact strength of the composites reinforced with nano‐SiO₂ deposited jute fibers were increased by 26.87% and 25.65%, respectively, compared with the untreated jute fibers. J. VINYL ADDIT. TECHNOL., 26:43–54, 2020. © 2019 Society of Plastics Engineers     

Mechanical properties and water absorption of fiber‐reinforced polypropylene composites prepared by bagasse and beech fiber

The present study investigates the tensile, flexural, notched Izod impact, and water absorption properties of bagasse and beech reinforced polypropylene (PP) composites as a function of fiber content. The surface of fibers was modified through the use of maleated polypropylene (MAPP) coupling agent. From this study, it was found that mechanical properties increase with an increase in fiber loading in both cases. However, the addition of wood fibers resulted in a decrease in impact strength of the composites. The water absorption property at varying fiber loading was evaluated and found maximum for the BA/PP composites. The weight gains for all specimens were less than 7%. In general, the results showed the usefulness of bagasse fiber as a good alternative and reinforcing agent for composite. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Lignin in jute fabric–polypropylene composites

In this work, the feasibility of using lignin as a compatibilizer for composites made from jute fiber fabric and polypropylene (PP) was studied. Since lignin contains polar (hydroxyl) groups and nonpolar hydrocarbon, it was expected to be able to improve the compatibility between the two components of the composite. It was found that lignin acted as β nucleation, fire retardant, and toughening agent for PP matrix. Jute composites exhibit higher stiffness, tensile strength, and impact behavior in respect to those of neat PP. Although scanning electron micrographic observations indicate that PP‐jute adhesion was slightly improved by lignin addition, additional benefits were only obtained from impact behavior. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Influence of maleated polypropylene on mechanical properties of composite made of viscose fiber and polypropylene

The purpose of this work was to study how viscose fiber behaves in polypropylene (PP) matrix when maleated polypropylene (MAPP) is used as a coupling agent. The influences of processing conditions on composite properties was of interest. Composites were characterized by FTIR and mechanical testing. The most notable result was the effect of the MAPP concentration on the tensile strength of the composites; the tensile strength increased from 40 to 69 MPa when MAPP was added in amounts up to 6 wt % of the fiber weight. The interaction between MAPP and fiber was confirmed with FTIR. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1895–1900, 2003     

Effect of the delignification of wood fibers on the mechanical properties of wood fiber–polypropylene composites

The effect of the delignification of hornbeam fibers on the mechanical properties of wood fiber–polypropylene (PP) composites was studied. Original fibers and delignified fibers at three levels of delignification were mixed with PP at a weight ratio of 40:60 in an internal mixer. Maleic anhydride (0.5 wt %) as the coupling agent and dicumyl peroxide (0.1 wt %) as the initiator were applied. The produced composites were then hot‐pressed, and specimens for physical and mechanical testing were prepared. The results of the properties of the composite materials indicate that delignified fibers showed better performance in the enhancement of tensile strength and tensile modulus, whereas the hardness of the composites was unaffected by delignification. Delignified fibers also exhibited better water absorption resistance. Notched impact strength was higher for delignified fiber composites, but it was reduced at higher delignification levels. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4759–4763, 2006     

汽车内饰用PP/黄麻纤维复合材料力学性能

采用转矩流变仪混合造粒,通过注射成型方法制备了聚丙烯(PP)/黄麻纤维复合材料,研究了对纤维表面进行处理的NaOH浓度、纤维含量和相容剂的含量对PP/黄麻纤维复合材料力学性能的影响,采用扫描电镜对纤维表面及复合材料的断面形貌进行分析。结果表明:黄麻纤维经过碱处理后PP/黄麻纤维复合材料的力学性能优于纤维未处理的复合材料的力学性能,随着NaOH浓度的提高,PP/黄麻纤维复合材料的拉伸强度和冲击强度增加,在NaOH浓度为16%时,其拉伸强度和冲击强度最佳;其弯曲强度随着NaOH浓度的提高先增加而后下降,在8%浓度时,弯曲强度最大。随着纤维含量的提高,PP/黄麻纤维复合材料的拉伸强度和弯曲强度先增加后下降,在纤维含量达到20%时,PP/黄麻纤维合材料的拉伸强度和弯曲强度达到最大。随着纤维含量的提高,PP/黄麻纤维复合材料的冲击强度降低。相容剂的加入使得PP/黄麻纤维复合材料的拉伸强度和弯曲强度明显增加。     

Effect of hybridization and compatibilization on the mechanical properties of recycled polypropylene‐hemp composites

Hemp fibers and particles, with different sizes and contents, were used to make hybrid composites based on recycled polypropylene (PP). In particular, the effect of maleated polypropylene (MAPP) addition on the morphology and mechanical properties is reported. The results show that better adhesion is obtained with MAPP addition. In general, fiber content and size had a substantial effect on the tensile, flexural, torsion, and impact properties of the resulting composites. Although, adding MAPP to the samples improved the impact strength of the composites, the values were always lower than neat PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

腰果酚接枝黄麻纤维不饱和聚酯复合材料的力学性能及界面调控

用甲苯二异氰酸酯与腰果酚(CNSL)合成大分子偶联剂接枝黄麻纤维。以接枝的黄麻纤维为增强体,通用的不饱和聚酯树脂为基体,采用热压方式制备复合材料。比较了纯饱和聚酯树脂、5 %CNSL增韧的不饱和聚酯树脂、25 %碱处理的黄麻纤维不饱和聚酯树脂复合材料和25 %的CNSL接枝黄麻纤维不饱和聚酯树脂复合材料的拉伸强度和冲击强度。结果表明,CNSL接枝于黄麻纤维上;CNSL的加入能提高材料的韧性,黄麻纤维能提高材料的拉伸强度而不能提高材料韧性;25 %CNSL接枝的黄麻纤维不饱和聚酯树脂能提高材料的拉伸强度和韧性,25 %CNSL接枝的黄麻纤维增强含5 %CNSL的不饱和聚酯复合材料,其冲击强度为12.10 kJ/m^2。     

Physico-mechanical studies of wood fiber reinforced composites

Wood polypropylene composites (WPC) of different compositions (30, 40, and 50%) have been prepared using maleic anhydride–polypropylene copolymer of different percentage (5 and 10% relative to their wood fiber content). Tensile, flexural, fracture toughness, and impact test of the prepared WPC were carried out. From the results, it is observed that the hard wood fiber–polypropylene composites, by using maleated polypropylene (MAH-PP), show comparatively better performance to soft wood fiber–polypropylene composites. Tensile strength and charpy impact strength have been increased to a maximum of 50 and 20%, respectively. The damping index has been decreased by 60% when 10% of MAH-PP has been used. Water absorption and scanning electron microscopy of the composites are also investigated.     

Impact modification of polypropylene‐based composites using surface‐coated waste rubber crumbs

Blends of maleated polypropylene (MAPP) with high contents of waste rubber powder, namely ground tire rubber and waste ethylene propylene diene monomer (EPDM) powder, were used as impact modifiers for polypropylene (PP) based composites with different reinforcements (hemp, talc, and milled glass fiber). Adding reinforcements led to increase in modulus (tensile, flexural, and torsion moduli) of PP, while its impact strength decreased noticeably. Impact modification of PP‐based composites was successfully performed via inclusion of MAPP/waste rubber compounds, especially compounds containing waste EPDM powder. Inclusion of such impact modifiers increased impact strength of composites over 80%. The effects of impact modification were more significant for hemp‐ and glass‐filled composites compared to composites containing talc. However, slight decrease in tensile, flexural, and torsion moduli (up to 30%) of the composites was also observed after inclusion of impact modifiers. POLYM. COMPOS., 35:2280–2289, 2014. © 2014 Society of Plastics Engineers     

黄麻纤维增强聚丙烯的力学性能

本文讨论了注塑成型黄麻纤维增强聚丙烯的制备方法和力学性能.将纤维重量含量分别为10%、20%和30%的复合材料进行比较,分析纤维含量对复合材料拉伸、弯曲和冲击性能的影响;将纤维分别切成约3mm、5mm和10mm长制成复合材料进行比较,分析纤维长度对复合材料拉伸、弯曲和冲击性能的影响.掺入黄麻纤维能使聚丙烯的拉伸和弯曲性能提高,但使其冲击强度降低;随纤维含量的增加或纤维长度的增加,复合材料的强度和模量是递增的,而冲击强度是递减的.