Preparation and properties of TPU micro/nanofibers by a laser melt‐electrospinning system

Laser melt electrospinning is a novel technology to fabricate scaffolds in the tissue engineering applications. The melt electrospinning is much safer than the conventional solution electrospinning due to without solvent effect. In this study, thermoplastic polyurethane (TPU) micro/nanofibers were successfully prepared by using this method. The effects of laser current and applied voltage on the fibers morphologies were investigated by scanning electron microscopy. The thermal behaviors and crystallization conditions of the TPU under different states were demonstrated by differential scanning calorimetry and X‐ray diffraction analysis. The mechanical property and the specific surface area of the TPU fibers membranes were also studied. All the analysis results showed that the effects of laser current and applied voltage on the average fiber diameter were complicated, the average fiber diameter ranging from 1.70 to 2.53 µm; the TPU is not an easily crystallized material; the electrospun fibers exhibited an amorphous phase; the average elongation at break laser of the electrospun TPU fiber membranes is about 134%; the average tensile strength is about 1.02 MPa and the specific surface area of the electrospun TPU fiber membrane is about 199 m²/g. POLYM. ENG. SCI., 54:1412–1417, 2014. © 2013 Society of Plastics Engineers     

Effect of solvent quality and humidity on the porous formation and oil absorbency of SAN electrospun nanofibers

In this study, nanofibrous mat with high oil sorption capability was prepared via one‐step electrospinning process without any further post‐treatments. For this purpose, the fabrication of styrene/acrylonitrile copolymer nanofibers was carried out using various dimethylformamide (DMF)/tetrahydrofuran and DMF/ethanol (DMF/EtOH) binary mixture ratios in an electrospining atmosphere with various relative humidity (RH) levels. Scanning electron microscope micrographs showed that DMF/tetrahydrofuran and DMF/EtOH ratio and RH value could considerably affect the diameter, surface, and interior morphology of the resultant nanofibers. The nanofiber morphology was dependent upon the polymer/solvent(s)/water ternary phase diagram behavior. In overall, the partial hydrophilicity of styrene/acrylonitrile copolymer resulted in electrospun nanofibers with wrinkled surface. In addition, the incorporation of nonsolvent in the spinning solution and using high RH atmosphere forced the polymeric solution jet to intensively phase separate and, therefore, produce the nanofibers with highly interior porous structure during drying process. The maximal capacity and rate of oil sorption (170 g/g) was observed for the nanofibrous mat prepared using EtOH/DMF (2/3: vol/vol) and RH value of 60% showing the highest internal porosity. The results showed that the oil sorption capability and mechanical strength of the fibrous mat are strongly dependent on nanofibers diameter and porous structure, which can be controlled through adjusting the RH and spinning solvent quality. The electrospun mat with highest Young's modulus (7.68 MPa) was prepared using EtOH/DMF (2/3) binary mixture and RH value of 45%. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45586.     

Preparation of poly(ether sulfone) nanofibers by gas‐jet/electrospinning

Poly(ether sulfone) (PES) nanofibers were prepared by the gas‐jet/electrospinning of its solutions in N,N‐dimethylformamide (DMF). The gas used in this gas‐jet/electrospinning process was nitrogen. The morphology of the PES nanofibers was investigated with scanning electron microscopy. The process parameters studied in this work included the concentration of the polymer solution, the applied voltage, the tip–collector distance (TCD), the inner diameter of the needle, and the gas flow rate. It was found from experimental results that the average diameter of the electrospun PES fibers depended strongly on these process parameters. A decrease in the polymer concentration in the spinning solutions resulted in the formation of nanofibers with a smaller diameter. The use of an 18 wt % polymer solution yielded PES nanofibers with an average diameter of about 80 nm. However, a morphology of mixed bead fibers was formed when the concentration of PES in DMF was below 20 wt % during gas‐jet/electrospinning. Uniform PES nanofibers with an average diameter of about 200 nm were prepared by this electrospinning with the following optimal process parameters: the concentration of PES in DMF was 25 wt %, the applied voltage was 28.8 kV, the gas flow was 10.0 L/min, the inner diameter of the needle was 0.24 mm, the TCD was 20 cm, and the flow rate was 6.0 mL/h. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Fabrication and characterization of nano‐SiC/ thermoplastic polyurethane hybrid heating membranes based on fine silver filaments

A novel method for fabricating flexible and waterproof heating membranes was presented in this study, nano‐SiC/thermoplastic polyurethane (TPU) hybrid membranes has been successfully prepared by pouring modified nano‐SiC/TPU solution into a mold with 0.05 mm silver filaments. Nano‐SiC particles were modified using silane coupling agent, subsequently, were dispersed evenly in the solvent, average diameter of nano‐SiC particles could reach 180.4 nm. Fourier Transform Infrared spectra showed organo‐functional groups were grafted on surface of nano‐SiC by covalent bond. TPU membrane with 10 wt % nano‐SiC had the highest decomposition temperature, and maximum stress. Thermal conductivity and the surface equilibrium temperature under the same loaded voltage of membranes ascended with increasing of nano‐SiC content. Flexible, waterproof nano‐SiC/TPU heating membranes have wide application prospect in active warming garments and other fields required flexible heating elements. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41498.     

Studying the Potential Application of Electrospun Polyethylene Terephthalate/Graphene Oxide Nanofibers as Electroconductive Cardiac Patch

Nowadays, engineering‐based cardiac patches aim to accelerate cardiac regeneration in myocardial infarcted tissues. Considering the fundamental role of cardiac electrophysiology in myocardial function, this study aims to investigate graphene oxide (GO) incorporation in the polyethylene terephthalate (PET) nanofibrous scaffold, as a conductive cardiac patch. The PET/GO nanocomposites are prepared using the uniaxial nozzle and coaxial nozzle electrospinning processes and comprehensively evaluated. The morphological observation indicates a uniform beaded free morphology with an average diameter of 147 ± 38 and 253 ± 67 nm for solid and core–shell nanocomposite fibers, respectively. Addition of GO to the PET nanofibers in a concentration of 0.05 wt% remarkably increases the Young modulus of mats from 30 ± 0.03 to 60 ± 0.02 and 69 ± 0.08 MPa for solid and core–shell nanofibers, respectively. Also, the electroconductivity is improved from 0.7 × 10^?6 to 1.175 × 10^?6 and 1.3 × 10^?6 S cm^?1 for solid and core–shell nanofibers, which are in the range of cardiac electroactivity values. PET/GO substrate interestingly supports human umbilical vein endothelial cells’ spreading morphology and cardiomyocyte elongated morphology, mainly where the GO nanosheets are distributed near the surface of nanofibers. In conclusion, the core–shell electrospun PET/GO nanocomposite fibers are suggested as a potential electroactive cardiac patch to improve cardiac cell attachment and proliferation.     

Effect of solution properties on nanofibrous structure of electrospun poly(lactic‐co‐glycolic acid)

Electrospinning of poly(lactic‐co‐glycolic acid) (PLGA) in chloroform or 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP) was investigated, focusing on its solution parameters, to develop nonwoven biodegradable nanofibrous structures for tissue engineering. PLGA nanofibers were obtained by electrospinning of 15 wt % PLGA solution and the resulting average fiber diameters were varied with the range of 270–760 nm, depending on solution property. When small amounts of benzyl triethylammonium chloride (BTEAC) was added to the PLGA/chloroform solution, the average diameter was decreased from 760 to 450 nm and the fibers were densely amounted in a straight shape. In addition, the average fiber diameter (270 nm) of nanofibers electrospun from polar HFIP solvent was much smaller than that (760 nm) of nanofibers electrospun from nonpolar chloroform solvent. Therefore, it could be concluded that conductivity or dielectric constant of the PLGA solution was a major parameter affecting the morphology and diameter of the electrospun PLGA fibers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1214–1221, 2006     

Preparation of chitosan bicomponent nanofibers filled with hydroxyapatite nanoparticles via electrospinning

Chitosan (CS) bicomponent nanofibers with an average diameter controlled from 100 to 50 nm were successfully prepared by electrospinning of CS and poly(vinyl alcohol) (PVA) blend solution. Finer fibers and more efficient fiber formations were observed with increased PVA contents. On this contribution, a uniform and ultrafine nanofibrous CS bicomponent mats filled with hydroxyapatite (HA) nanoparticles were successfully electrospun in a well devised condition. An increase in the contents of HA nanoparticles caused the conductivity of the blend solution to increase from 1.06 mS/cm (0 wt % HA) to 2.27 mS/cm (0.5 wt % HA), 2.35 mS/cm (1.0 wt % HA), respectively, and the average diameter of the composite fibers to decrease from 59 ± 10 nm(0 wt % HA) to 49 ± 10 nm (0.5 wt % HA), 46 ± 10 nm (1.0 wt % HA), respectively. SEM images showed that some particles had filled in the nanofibers whereas the others had dispersed on the surface of fibers, and EDXA results indicated that both the nanoparticles filled in the nanofibers and those adhered to the fibers were HA particles. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Optimization of centrifugally spun thermoplastic polyurethane nanofibers for air filtration applications

While our knowledge of fiber formation by using conventional nanofiber spinning techniques has increased to a considerable extent, there are still few studies on centrifugal spinning either in academia or in the industry. Centrifugal spinning is a comparatively new method of producing fibers having nano- or microscale diameters. In this study, three main parameters (nozzle orifice diameter, rotational speed, polymer concentration) of centrifugal spinning were optimized to produce air filter media from thermoplastic polyurethane nanofibers. The effect of concentration of polymer solution was found to be a major contributor in TPU fibers optimization estimating 77.5%. After the optimization studies, the average fiber diameter of nanofiber sample produced at optimum conditions (22G needle as an orifice, 4000 rpm, and 10 wt% concentration of polymer solution) was 205 ± 84 nm. Aerosol filtration performance of the produced webs was analyzed. Filtration efficiency of the optimized sample was found to be 99.4% for 0.3 µm particle size at an expense of 98 Pa pressure drop.

Copyright © 2018 American Association for Aerosol Research     

Influence of humidity,temperature, and annealing on microstructure and tensile properties of electrospun polyacrylonitrile nanofibers

This study investigates the microstructure and mechanical properties of electrospun nanofibers from polyacrylonitrile (PAN)‐dimethylformamide (DMF) solution at different relative humidity (RH) in the range from 14% to 60% and two different temperatures (20°C and 40°C). Nanofibers produced at low RH (22% or less at 20°C) exhibit relatively smooth surface and solid core, whereas at higher RH (30% or higher at 20°C) rough surface and porous core are observed. The resulting morphology is explained by means of H₂O/DMF/PAN ternary phase diagram. At higher RH, the water diffusion into polymer‐solution jet brings thermodynamic instability into the system leading to separation of polymer‐rich phase and polymer‐lean phase, where the later contributes to porosity. Higher process temperature (40°C) yields larger miscibility area in the ternary phase diagram leading to formation of porous structure at relatively higher RH (40%). Tensile strength of nanofibrous yarns is found to vary from 80 MPa to 130 MPa depending on the processing temperature and RH. The amount of porosity is found to affect the tensile properties of nanofibers most significantly, although diameter and crystallinity play important role. Annealing is found to alleviate surface roughness and porosity and increase crystallinity. Tensile strength of nanofibrous yarns is found to improve by up to 25% after annealing. POLYM. ENG. SCI., 58:998–1009, 2018. © 2017 Society of Plastics Engineers     

Aligned electrospun sulfonated polyetheretherketone nanofiber based proton exchange membranes for fuel cell applications

In this study, electrospinning of sulfonated poly(ether ether ketone) (SPEEK) at different degrees of sulfonation (DS) was investigated. The polymer solution concentration of 22 wt% was obtained to collect smooth fiber in nanoscale range of 112 to 131 nm at various conditions. SEM observations of SPEEK nanofibers showed the decrease of diameter with increasing DS from 74% to 81%, mainly due to the increase of electrical conductivity of polymer solution at higher DS. The increase of collecting speed from 20 to 305 m/min decreased the diameter of nanofibers slightly and improved their alignment. The presence of SO₃H groups in collected nanofibers was demonstrated with FT‐IR analysis. WAXD patterns of SPEEK nanofibers indicated featureless amorphous peak with no crystalline regions that was broaden at higher DS and aligned nanofibers. The electrochemical impedance spectroscopy of SPEEK nanofibers showed the through‐plane proton conductivity of fully hydrated nanofibrous membranes measured at room temperature were improved with DS. The proton conductivity of randomly oriented and aligned nanofibers were measured from 0.0098 to 0.0722 S/cm and from 0.0592 to 0.0907 S/cm, respectively. Aligned nanofibers exhibited more proton conductivity than randomly collected nanofibers. POLYM. ENG. SCI., 57:789–796, 2017. © 2016 Society of Plastics Engineers     

Drug‐loaded polyurethane/clay nanocomposite nanofibers for topical drug‐delivery application

In this study, polyurethane/nanoclay nanocomposite nanofibrous webs were prepared by electrospinning. An antiseptic drug, chlorhexidine acetate (CA), was loaded onto montmorillonite clay and was then incorporated into polyurethane nanofibers. For comparison, the CA drug was loaded directly into the polyurethane solution dope used to electrospin the nanofibers. The emphasis was on investigating the effect of the drug loading into the nanoclay vis‐à‐vis direct drug loading on the drug‐release behavior of nanofibrous webs. The nanofibrous webs were also evaluated for other properties, such as moisture vapor transmission, porosity determination, contact angle measurement, and antibacterial activity, which are important for topical drug‐delivery application. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40230.     

Modeling and optimization of sulfonated poly (ether ether ketone) nanofibrous proton exchange membranes with response surface methodology

The morphological control of proton conductive nanofibrous mat used in proton exchange membranes (PEMs) is a key issue to improve proton conductivity of PEMs. In this study, response surface methodology (RSM) was utilized to investigate the morphological characterizations of electrospun sulfonated poly (ether ether ketone) (SPEEK) nanofibrous membranes. The effects of electrospinning parameters namely solution concentration, applied voltage and tip to collector distance were studied on the average diameter, its standard deviation and the degree of alignment of SPEEK nanofibers. The adequacy of the response surface models was verified by the validation experiments. Optimized conditions were obtained to meet the desired status of collecting more uniform and finer nanofibers with improved alignment. After obtaining the significant factors and optimal test level, an additional optimization was conducted at different take‐up speeds to fabricate high‐grade aligned nanofibers. The resultant nanofibers had the diameter of 107 ± 22 nm at the optimum point which was in good agreement with the predicted response values. The highest degree of alignment was yielded at the take‐up speed of 8.8 m/s with the maximum second‐order orientation parameter of 0.869. Electrochemical spectroscopy analysis showed that the aligning of proton conductive nanofibers improved in‐plane proton conductivity about 67%. POLYM. ENG. SCI., 2017. © 2017 Society of Plastics Engineers     

Three‐layered electrospun PVA/PCL/PVA nanofibrous mats containing tetracycline hydrochloride and phenytoin sodium: A case study on sustained control release,antibacterial, and cell culture properties

The main objective of this work was to prepare a tailor‐made electrospun nanofibrous samples based on poly(?‐caprolactone) (PCL) containing tetracycline hydrochloride (TC‐HCl) as a middle layer and poly(vinyl alcohol) (PVA) including phenytoin sodium (PHT‐Na) as lateral layers. The characterizations of the three‐layered electrospun samples were carried out by using SEM, ATR‐FTIR spectroscopy along with swelling/weight loss, UV–vis spectrophotometry as well as HPLC, antibacterial and MTT tests. The SEM micrograph images showed that the average diameter of PCL nanofibers was decreased from 243 ± 7 nm to 181 ± 5 nm by adding TC‐HCl. The hydrolytic degradation of PVA nanofibers in the exposure of phosphate buffer solution (PBS) was confirmed by ATR‐FTIR results in which a change at the intensity of the characteristic peak located at 3333 cm^?1 corresponding to hydroxyl groups (? OH) was observed. The UV–vis outcomes revealed a sustained control release of TC‐HCl from the three‐layered nanofibrous samples (PVA/PCL/PVA) with an amount of about 43% compared to the PCL nanofibers which had an ultimate release of the drug about 79%. Furthermore, the HPLC chromatograms showed the released PHT‐Na from PVA nanofibers about 87%. Finally, the MTT assay along with the antibacterial evaluation exhibited that the surfaces of these electrospun three‐layered nanofibrous samples have no cytotoxicity as well as the controlled release of TC‐HCl from them enabled their prolonged use for preventing the bacterium growth such as S. aureus during 24‐h treatment time. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43309.     

Electrospinning of thermoplastic polyurethane microfibers and nanofibers from polymer solution and melt

Electrospinning technique was used to produce ultrafine fibers from thermoplastic polyurethane (TPU). A direct comparison between melt and solution electrospinning of TPU was provided for the evaluation of process–structure relationship. It was found that the deposition rate of melt electrospinning (0.6 g h^?1) is four times higher than that of solution electrospinning (0.125 g h^?1) for TPU under the same processing condition. However, the average fiber diameters of solution electrospun TPUs (220–280 nm) were much lower than those of melt electrospun TPUs (4–8 μm). The effect of processing variables including collection distance and electric field strength on the electrospun fiber diameter and morphology was also studied. The findings indicate that increasing the electric field strength yielded more electrical forces acting on polymer jet and resulted in a decrease in fiber diameter as a result of more fiber drawing in both solution and melt electrospun fibers. It was also demonstrated that increasing the collection distance led to an improvement in the solidification of melt electrospun fibers and thus less fused fibers were obtained. Finally, a close investigation of fiber structures revealed that melt electrospun TPU fibers had smooth surface, whereas solution electrospun TPU fibers showed high intensity of cracks on the fiber surface. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

A novel soluble PANI/TPU composite doped with inorganic and organic compound acid

A series of novel soluble and thermoplastic polyurethane/polyaniline (TPU/PANI) composites doped with a compound acid, which was composed of an organic acid (p‐toluene sulfonic acid) and an inorganic acid (phosphoric acid), were successfully prepared by in situ polymerization. The effect of aniline (ANI) content, ratio of organic acid/inorganic acid, and different preparation methods on the conductivity of the TPU/PANI composites were investigated by using conductivity measurement. Lithium bisoxalato borate (LiBOB) was added to the prepared in situ TPU/PANI to coordinate with the ether oxygen groups originating from the soft molecular chains of TPU, and thus the conductivity of the composites was further enhanced. The molecular structure, thermal properties, and morphology of the TPU/PANI composites were studied by UV–visible spectroscopy, differential scanning calorimetry, and scanning electron microscopy, respectively. The results show that the in situ TPU/PANI composites doped with the compound acid can be easily dissolved in normal solvents such as dimethylformamide (DMF) and 1,4‐dioxane. The conductivity of the TPU/PANI composites increases with the increase of the ANI content, in the ANI content range of 0–20 wt %; however, the conductivity of the composites reduces with further increment of ANI content. The conductivity of the TPU/PANI composites prepared by in situ polymerization is about two orders of magnitude higher than that prepared by solution blending method. LiBOB can endow the in situ TPU/PANI composites with an ionic conductivity. The dependence of the conductivity on temperature is in good accordance with the Arrhenius equation in the temperature range of 20–80°C. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Blends of thermoplastic polyurethane and polypropylene. I. Mechanical and phase behavior

Pure thermoplastic polyurethane (TPU), polypropylene (PP), and TPU/PP blends with different weight ratios prepared in a twin‐screw extruder were investigated by dynamic mechanical analysis (DMA), the universal tester for mechanical investigation, and by wide‐angle X‐ray diffraction (WAXD). The addition of PP above 20 wt % to the TPU stepwise changed the ductility and Young's modulus, i.e., apparently a kind of ductile → brittle transition occurred between TPU/PP 80/20 and TPU/PP 60/40 blends. This fact and the result of analysis of WAXD curves indicated matrix → dispersed phase inversion in this concentration region. TPU melt enabled easier migration of the PP chains and prolonged crystallization of PP matrix during solidification process affecting thus crystallite size, orientation, and crystallinity. In accordance to this fact, DMA results indicated partial miscibility of PP with polyurethane in the TPU/PP blends due to the lack of interfacial interaction and adhesion between the nonpolar crystalline PP and polar TPU phases. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104, 3980–3985, 2007     

Effects of processing parameters on morphology of electrospun polystyrene nanofibers

This study focused on the preparation of electrospun polystyrene (PS) nanofibers. PS solutions were prepared in single (dimethylformamide; DMF, dimethylacetamide; DMAc or tetrahydrofuran; THF) and mixed solvent (DMF/THF and DMAc/THF) systems with and without tetrabutylammonium bromide (TBAB) salt. The effects of PS concentration, solvent system, the addition of salt, appearance and diameter of PS fibers were examined. The average diameter of the as-spun fibers increased upon increasing PS concentration. The morphology of the fibers significantly depended on the properties of the solvents. The obtained fibers were smooth without any beads and their diameters were affected by the amount of THF in the solvent and PS concentration. The beads in the fibers disappeared and the fiber diameter significantly decreased after the addition of TBAB. The smallest diameter and the narrowest diameter distribution of PS nanofibers (376±36 nm) were obtained from 15% PS solution in DMAc with 0.025% w/v TBAB.     

The mechanical and rheological behavior of the PA/TPU blend with POE‐g‐MA modifier

In this research, we attempt to improve the impact strength and the viscosity of PA (polyamide) by blending two elastomers, TPU (thermoplastic polyurethane) and POE‐g‐MA (maleic anhydride‐grafted polyethylene‐octene elastomer), in PA matrix with twin screw extruder. The ratio of blending is 80PA/20TPU and 80PA/20TPU/20POE‐g‐MA (66.66PA/16.67TPU/16.67POE‐g‐MA). Results indicate that POE‐g‐MA improves the low viscosity of PA and TPU during the blending process, and also their compatibility. Thus, the 80PA/20TPU/20POE‐g‐MA blend has better tensile stress and elongation than 80PA/20TPU blend, and furthermore POE‐g‐MA significantly improves the impact strength of PA, even to super‐toughness grade. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Fabrication and characterization of chitosan/kefiran electrospun nanofibers for tissue engineering applications

Chitosan (CS)-based nanofibrous scaffolds are very promising in tissue engineering applications. However, electrospinning of CS is not possible unless using toxic solvents such as trifluoroacetic acid or by blending with other polymers. In the present study, we investigated CS-based nanofibers' fabrication by blending it with kefiran as a natural polysaccharide. A series of solutions with various CS to kefiran ratios were prepared and underwent electrospinning. The effects of main process parameters, including applied voltage and needle tip-to-collector distance on nanofibers' diameter and morphology, were also studied. Nanofibers containing 80% CS and 20% Kefiran with an average diameter of 81 ± 17 nm were successfully electrospun. Thermogravimetric analysis indicated the presence of both polymers in blend nanofibers. The diameter of CS/kefiran nanofibers increased with enhanced applied voltage, while needle tip-to-collector distance did not significantly affect the mean diameters. Appropriate viability of l929 cells on the obtained scaffolds was demonstrated utilizing Alamar blue assay. Also, cell attachment onto the fiber surface was confirmed by scanning electron microscopy. Results indicated that CS/kefiran nanofibrous scaffolds would be promising for tissue engineering applications.     

Fabrication of antibacterial silver nanoparticle‐modified chitosan fibers using Eucalyptus extract as a reducing agent

Green chemical method could be a promising route to achieve large scale synthesis of nanostructures for biomedical applications. Here, we describe a green chemical synthesis of silver nanoparticles (Ag NPs) on chitosan‐based electrospun nanofibers using Eucalyptus leaf extract. A series of silver salt (AgNO₃) amounts were added to a certain composition of chitosan/polyethylene oxide aqueous acetic acid solution. The solutions were then electrospun to obtain nanofibrous mats and then, morphology and size of nanofibers were analyzed by scanning electron microscopy (SEM). Incubation of AgNO₃‐containing mats into Eucalyptus leaf extract led to the formation of Ag NP clusters with average diameter of 91 ± 24 nm, depicted by SEM and transmission electron microscopy. Surface enhanced Raman spectroscopy also confirmed formation of Ag NPs on the nanofibers. The mats also showed antimicrobial activity against Escherichia coli and Staphylococcus aureus bacteria with bigger inhibition zone for extract‐exposed mats against S. aureus. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42133.