High-Temperature Exposure Studies of HVOF-Sprayed Cr<Subscript>3</Subscript>C<Subscript>2</Subscript>-25(NiCr)/(WC-Co) Coating

In this research, development of Cr₃C₂-25(NiCr) + 25%(WC-Co) composite coating was done and investigated. Cr₃C₂-25(NiCr) + 25%(WC-Co) composite powder [designated as HP2 powder] was prepared by mechanical mixing of [75Cr₃C₂-25(NiCr)] and [88WC-12Co] powders in the ratio of 75:25 by weight. The blended powders were used as feedstock to deposit composite coating on ASTM SA213-T22 substrate using High Velocity Oxy-Fuel (HVOF) spray process. High-temperature oxidation/corrosion behavior of the bare and coated boiler steels was investigated at 700 °C for 50 cycles in air, as well as, in Na₂SO₄-82%Fe₂(SO₄)₃ molten salt environment in the laboratory. Erosion-corrosion behavior was investigated in the actual boiler environment at 700 ± 10 °C under cyclic conditions for 1500 h. The weight-change technique was used to establish the kinetics of oxidation/corrosion/erosion-corrosion. X-ray diffraction, field emission-scanning electron microscopy/energy-dispersive spectroscopy (FE-SEM/EDS), and EDS elemental mapping techniques were used to analyze the exposed samples. The uncoated boiler steel suffered from a catastrophic degradation in the form of intense spalling of the scale in all the environments. The oxidation/corrosion/erosion-corrosion resistance of the HVOF-sprayed HP2 coating was found to be better in comparison with standalone Cr₃C₂-25(NiCr) coating. A simultaneous formation of protective phases might have contributed the best properties to the coating.     

Microstructure and Properties of HVOF-Sprayed WC-(W,Cr)<Subscript>2</Subscript>C-Ni Coatings

The composition WC-(W,Cr)₂C-Ni is one of the standard compositions used for the preparation of thermally sprayed coatings by high velocity oxy-fuel (HVOF) spraying. Surprisingly, this composition has been poorly investigated in the past. Frequent use of commercial designations WC-‘CrC’-Ni, WC-Cr₃C₂-Ni, and WC-NiCr indicates the insufficient knowledge about the phase compositions of these powders and coatings. The properties of these coatings differ significantly from those of WC-Co and WC-CoCr coatings. In this paper, the results of different series of experiments conducted on HVOF-sprayed WC-(W,Cr)₂C-Ni coatings are compiled and their specific benefits pointed out. The focus of this study is on the analysis of the microstructures and phase compositions of the feedstock powders and coatings. Unlike WC-Co and Cr₃C₂-NiCr, WC-(W,Cr)₂C-Ni is not a simple binary hard phase—binder metal composite. The phase (W,Cr)₂C with unknown physical and mechanical properties appears as a second hard phase, which is inhomogeneously distributed in the feedstock powders and coatings. As examples of coating properties, the oxidation resistance and dry sliding wear properties are compared with those of WC-10%Co-4%Cr coatings.     

Multiscale Experimental and Numerical Approach to the Powder Particle Shape Effect on Al-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Coating Build-Up

Aluminum (Al) powders with spherical and irregular particle shapes were mixed with two alumina (Al₂O₃) powders with either a spherical or an angular particle shape to achieve high-performance cold-sprayed coatings onto steel. Two effects of the aluminum particle shape were observed. First, coating microstructure observation showed impinging heterogeneity depending on particle shape. Second, particle jet differences depending on particle morphology were shown by velocity maps. From the latter, SEM and XRD, three effects of the alumina particle shape were also shown, i.e., higher in-flight velocity of angular particles, fragmentation of spherical hollow particles and embedding of alumina particles with aluminum. Numerical simulation of particle impacts was developed to study the densification of Al coating due to Al₂O₃ addition through elucidation of Al-Al₂O₃ interaction behavior at the scale of the coating. Al/Al and Al/Al₂O₃ interfaces were investigated using TEM to understand coating strengthening effects due to alumina addition at the scale of the particle. As a whole, Al and Al₂O₃ particle shape effects were claimed to explain coating mechanical properties, e.g., microhardness and coating–substrate bond strength. This study resulted in specifying criteria to help cold spray users in selecting powders for their applications, to meet economic and technical requirements.     

Preparation and optical properties of Y<Subscript>2</Subscript>O<Subscript>3</Subscript>/SiO<Subscript>2</Subscript> powder

Y(NO3)3 and NH3·H2O were used as a raw materials,and nano-Y2O3 powder was successfully synthesized by a precipitation method.Employing TEOS as a raw material,SiO2 powder was successfully prepared by a alkoxide-hydrolysis method,and a Y2O3/SiO2 composite powder was obtained by coating.The Y2O3,SiO2,and Y2O3/SiO2 powders were characterized using X-ray diffraction(XRD),scanning electron microscopy(SEM),and Fourier transform infrared spectrophotometer(FT-IR);the Y2O3 and Y2O3/SiO2 powders were further examined ...     

Mechanical alloying characteristic and thermal stability of Al<Subscript>78</Subscript>Fe<Subscript>20</Subscript>Zr<Subscript>2</Subscript> amorphous powders

The powders of pure Al, Fe, and Zr for preparing Al₇₈Fe₂₀Zr₂ were subject to a high-energy planetary ball milling. The microstructure evolution of the mixtures at the different intervals of milling was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). It was found that a nearly complete amorphization could be achieved in the mixtures after ball milling for 23 h. Further ball milling led to the crystallization of the amorphous powders. A long time ball milling, e.g., 160 h, led to a complete crystallization of the amorphous powders and the formation of Al₃Zr and Al1₃Fe₄. The crystallization products caused by ball milling are almost the same as that produced by isothermal annealing of the amorphous powders in vacuum at 800 K for 1 h.     

Influences of NiCO<Subscript>3</Subscript> content on the microstructure and magnetic properties of Ni<Subscript>0.5</Subscript>Zn<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> powders prepared by SHS

Stoichiometric Ni_0.5Zn_0.5Fe₂O₄ powders were produced by self-propagating high temperature synthesis (SHS). The effects of NiCO₃ content in the raw materials on the microstructure and magnetic properties of Ni-Zn ferrite powders were systematically studied. The Ni_0.5Zn_0.5Fe₂O₄ powders were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The magnetic properties of the powders were evaluated by vibrating sample magnetometry (VSM). The results show that the introduction of NiCO₃ into reactants improves the conversion percentage and refines the Ni_0.5Zn_0.5Fe₂O₄ particles. The increase of NiCO₃ content enhances the magnetic properties of Ni_0.5Zn_0.5Fe₂O₄. Particularly, the saturation magnetization reaches the maximum when the NiCO₃ content is 3 at.%.     

Preparation and characterization of nanostructured Bi<Subscript>2</Subscript>Se<Subscript>3</Subscript> and Sn<Subscript>0.5</Subscript>-Bi<Subscript>2</Subscript>Se<Subscript>3</Subscript>

Nanostructured Bi₂Se₃ and Sn_0.5-Bi₂Se₃ were successfully synthesized by hydrothermal coreduction from SnCl₂·H₂O and the oxides of Bi and Se. The products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and field emission scanning electron microscope (FESEM). Bi₂Se₃ powders obtained at 180°C and 150°C consist of hexagonal flakes of 50–150 nm in side length and nanorods of 30–100 nm in diameter and more than 1 μm in length. The product obtained at 120°C is composed of thin irregular nanosheets with a size of 100–200 nm and several nanometers in thickness. The major phase of Sn_0.5-Bi₂Se₃ synthesized at 180°C is similar to that of Bi₂Se₃. Sn_0.5-Bi₂Se₃ powders are primarily nanorod structures, but small amount of powders demonstrate irregular morphologies.     

Solvothermal synthesis and thermoelectric properties of skutterudite compound Fe（0.25）Ni（0.25）Co（0.5）Sb3

Nanostructured skutterudite-related compound Fe_0.25Ni_0.25Co_0.5Sb₃ was synthesized by a solvothermal method using FeCl₃, NiCl₂, CoCl₂, and SbCl₃ as the precursors and NaBH₄ as the reductant. The solvothermally synthesized powders consisted of fine granules with an average particle size of tens of nanometers. The bulk material was prepared by hot pressing the powders. Transport property measurements indicated a heavily doped semiconductor behavior with n-type conduction. The thermal conductivity is about 1.83 W·m⁻¹·K⁻¹ at room temperature and decreases to 1.57 W·m⁻¹·K⁻¹ at 673 K. The low thermal conductivity is attributed to small grain size and high porosity. A maximum dimensionless figure of merit of 0.15 is obtained at 673 K.     

The Influence of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Powder Morphology on the Properties of Cu-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Composites Designed for Functionally Graded Materials (FGM)

In order to meet the requirements of an increased efficiency applying to modern devices and in more general terms science and technology, it is necessary to develop new materials. Combining various types of materials (such as metals and ceramics) and developing composite materials seem to be suitable solutions. One of the most interesting materials includes Cu-Al₂O₃ composite and gradient materials (FGMs). Due to their potential properties, copper-alumina composites could be used in aerospace industry as rocket thrusters and components in aircraft engines. The main challenge posed by copper matrix composites reinforced by aluminum oxide particles is obtaining the uniform structure with no residual porosity (existing within the area of the ceramic phase). In the present paper, Cu-Al₂O₃ composites (also in a gradient form) with 1, 3, and 5 vol.% of aluminum oxide were fabricated by the hot pressing and spark plasma sintering methods. Two forms of aluminum oxide (αAl₂O₃ powder and electrocorundum) were used as a reinforcement. Microstructural investigations revealed that near fully dense materials with low porosity and a clear interface between the metal matrix and ceramics were obtained in the case of the SPS method. In this paper, the properties (mechanical, thermal, and tribological) of composite materials were also collected and compared. Technological tests were preceded by finite element method analyses of thermal stresses generated in the gradient structure, and additionally, the role of porosity in the formation process of composite properties was modeled. Based on the said modeling, technological conditions for obtaining FGMs were proposed.     

Chemical Stability and Biological Properties of Plasma-Sprayed CaO-SiO<Subscript>2</Subscript>-ZrO<Subscript>2</Subscript> Coatings

In this work, calcia-stabilized zirconia powders were coated by silica derived from tetraethoxysilane (TEOS) hydrolysis. After calcining at 1400 °C, decalcification of calcia-stabilized zirconia by silica occurred and powders composed of Ca₂SiO₄, ZrO₂, and CaZrO₃ were prepared. We produced three kinds of powders with different Ca₂SiO₄ contents [20 wt.% (denoted as CZS2), 40 wt.% (denoted as CZS4), and 60 wt.% (denoted as CZS6)]. The obtained powders were sprayed onto Ti-6Al-4V substrates using atmospheric plasma spraying. The microstructure of the powders and coatings were analyzed. The dissolution rates of the coatings were assessed by monitoring the ions release and mass losses after immersion in Tris-HCl buffer solution. Results showed that the chemical stability of the coatings were significantly improved compared with pure calcium silicate coatings, and increased with the increase of Zr contents. The CZS4 coating showed not only good apatite-formation ability in simulated body fluid, but also well attachment and proliferation capability for the canine bone marrow stem cells. Results presented here indicate that plasma-sprayed CZS4 coating has medium dissolution rate and good biological properties, suggesting its potential use as bone implants.     

Influence of Feedstock Powder Modification by Heat Treatments on the Properties of APS-Sprayed Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-40% TiO<Subscript>2</Subscript> Coatings

The formation and decomposition of aluminum titanate (Al₂TiO₅, tialite) in feedstock powders and coatings of the binary Al₂O₃-TiO₂ system are so far poorly understood. A commercial fused and crushed Al₂O₃-40%TiO₂ powder was selected as the feedstock for the experimental series presented in this paper, as the composition is close to that of Al₂TiO₅. Part of that powder was heat-treated in air at 1150 and 1500 °C in order to modify the phase composition, while not influencing the particle size distribution and processability. The powders were analyzed by thermal analysis, XRD and FESEM including EDS of metallographically prepared cross sections. Only a maximum content of about 45 wt.% Al₂TiO₅ was possible to obtain with the heat treatment at 1500 °C due to inhomogeneous distribution of Al and Ti in the original powder. Coatings were prepared by plasma spraying using a TriplexPro-210 (Oerlikon Metco) with Ar-H₂ and Ar-He plasma gas mixtures at plasma power levels of 41 and 48 kW. Coatings were studied by XRD, SEM including EDS linescans of metallographically prepared cross sections, and microhardness HV1. With the exception of the powder heat-treated at 1500 °C an Al₂TiO₅-Ti₃O₅ (tialite–anosovite) solid solution Al_2?xTi_1+xO₅ instead of Al₂TiO₅ existed in the initial powder and the coatings.     

Crystallographic Features of Phases Involved in the Oxidation of Ti<Subscript>3</Subscript>Ni<Subscript>3</Subscript>CrSi<Subscript>6</Subscript>

The oxidation behaviour of Ti₃(Ni,Cr)₃CrSi₆ and Ti₄Ni₄Si₇ was studied in air both at 1000 and 1100 °C. The formation of the oxidation products and the phase transformation were characterized by in situ X-ray diffraction and SEM-FEG post-mortem observations. The crystal structure of Ti₃(Ni,Cr)₃CrSi₆ was also determined using powder X-ray diffraction and Rietveld refinement in order to describe this phase as a pseudolamellar structure comparable to the one of Ti₄Ni₄Si₇. Results evidenced that diffusion in solid state governs the oxidation rate of these silicides. Ti₄Ni₄Si₇ oxidation rate was assessed as being one order of magnitude lower than the one of Ti₃(Ni,Cr)₃CrSi₆, while this latter readily transformed into Ti₄Ni₄Si₇ during the first time of oxidation. The understanding of this particular behaviour in which the oxidation rate of Ti₃(Ni,Cr)₃CrSi₆ was not affected by the phase transformation implied to consider the crystallographic lamellar features of these compounds that play a major role in the diffusion of the most oxidizable elements.     

Phase Diagram of the Quaternary Al(NO<Subscript>3</Subscript>)<Subscript>3</Subscript>-Cu(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>-Zn(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>-H<Subscript>2</Subscript>O System

The phase diagram of the H₂O-Zn(NO₃)₂-Al(NO₃)₃-Cu(NO₃)₂ quaternary system at 30 °C has been established by using the conductivity measurements. The solid-liquid equilibria of the H₂O-Zn(NO₃)₂-Al(NO₃)₃, H₂O-Zn(NO₃)₂-Cu(NO₃)₂, H₂O-Al(NO₃)₃-Cu(NO₃)₂ ternary systems and two isoplethic sections were determined experimentally. The solid phases in equilibrium with the saturated solution are the tri- and hemipentahydrate of copper nitrate, the hexahydrate α and β of the zinc nitrate and the nonahydrate of aluminum nitrate. The copper and zinc nitrates are relatively soluble in opposition to the aluminum nitrate which presents some important precipitation domains.     

Synthesis and characterization of Li<Subscript>1.3</Subscript>Al<Subscript>0.3</Subscript>Ti<Subscript>1.7</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>-coated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> by wet chemical route

Li_1.3Al_0.3Ti_1.7(PO₄)₃-coated LiMn₂O₄ was prepared by wet chemical route. The phase, surface morphology, and electrochemical properties of the prepared powders were characterized by X-ray diffraction, scanning electron micrograph, and galvanostatic charge-discharge experiments. Li_1.3Al_0.3Ti_1.7(PO₄)₃-coated LiMn₂O₄ has similar X-ray diffraction patterns as LiMn₂O₄. The corner and border of Li_1.3Al_0.3Ti_1.7(PO₄)₃-coated LiMn₂O₄ particles are not as clear as the uncoated one. The two powders show similar values of lithium-ion diffusion coefficient. When cycled at room temperature and 55°C for 40 times at the charge-discharge rate of 0.2C, Li_1.3Al_0.3Ti_1.7(PO₄)₃-coated LiMn₂O₄ shows the capacity retentions of 98.2% and 93.9%, respectively, which are considerably higher than the values of 85.4% and 79.1% for the uncoated one. Both the capacity retention differences between Li_1.3Al_0.3Ti_1.7(PO₄)₃-coated LiMn₂O₄ and LiMn₂O₄ cycling at room temperature and 55°C become larger with the increase of charge-discharge rate. When the charge-discharge rate reaches 2C, the capacity retention of LATP-coated LiMn₂O₄ becomes 8.4% higher than the uncoated LiMn₂O₄ for room temperature cycling, and it becomes 11.1% higher than the latter when cycled at 55°C.     

Microstructure and Mechanical Behavior of Microwave Sintered Cu<Subscript>50</Subscript>Ti<Subscript>50</Subscript> Amorphous Alloy Reinforced Al Metal Matrix Composites

In the present work, Al metal matrix composites reinforced with Cu-based (Cu₅₀Ti₅₀) amorphous alloy particles synthesized by ball milling followed by a microwave sintering process were studied. The amorphous powders of Cu₅₀Ti₅₀ produced by ball milling were used to reinforce the aluminum matrix. They were examined by x-ray diffraction (XRD), scanning electron microscopy (SEM), microhardness and compression testing. The analysis of XRD patterns of the samples containing 5 vol.%, 10 vol.% and 15 vol.% Cu₅₀Ti₅₀ indicates the presence of Al and Cu₅₀Ti₅₀ peaks. SEM images of the sintered composites show the uniform distribution of reinforced particles within the matrix. Mechanical properties of the composites were found to increase with an increasing volume fraction of Cu₅₀Ti₅₀ reinforcement particles. The hardness and compressive strength were enhanced to 89 Hv and 449 MPa, respectively, for the Al-15 vol.% Cu₅₀Ti₅₀ composites.     

MO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>–ZrO<Subscript>2</Subscript> coatings with M=Al,Mg, Zr,Ti, and Nb on valve metals

Coatings formed on aluminum, titanium, magnesium, zirconium, and niobium by means of plasma-electrolytic oxidation in an aqueous electrolyte containing MgZrF are studied. All elements involved in the composition of the complex compound are present in the coatings. Contents of the elements involved in the inner sphere are the largest. Phase and elementary compositions of the coatings depend on the nature of the valve metal. All coatings contain ZrO₂ in either cubic or monoclinic modifications. The main phase of the coatings formed on magnesium is MgF₂. According to the surface structure, the coatings can be divided into three groups: large-pore (on Mg, Al, and Ti), small-pore (on Nb), and compact with a wavy surface (on Zr).     

Oxidation Behavior of TiAl<Subscript>3</Subscript>/Al Composite Coating on Orthorhombic-Ti<Subscript>2</Subscript>AlNb Based Alloy at Different Temperatures

This paper reports the oxidation behavior of TiAl₃/Al composite coating deposited by cold spray. The substrate alloy was orthorhombic-Ti-22Al-26Nb (at.%). The oxidation kinetics of the coating was tested at 650, 800, and 950 °C, respectively. The parabolic rate constant for the coating oxidized at 650 °C was k _p = 7.2 × 10⁻² mg·cm⁻²·h^−1/2 for the tested 1200 h. For the coating oxidized at 800 °C, the oxidation kinetics could be separated into two stages with k _p value of 39.8 × 10⁻² mg·cm⁻²·h^−1/2 for the initial 910 h and 17.7 × 10⁻² mg·cm⁻²·h^−1/2 for the stage thereafter. For the coating oxidized at 950 °C, the oxidation kinetics can be separated into three stages with k _p of 136.9 × 10⁻² mg·cm⁻²·h^−1/2 in the first 100 h, followed by 26.9 × 10⁻² mg·cm⁻²·h^−1/2 from 100 to 310 h, and 11.8 × 10⁻² mg·cm⁻²·h^−1/2 from 310 to 1098 h. XRD, SEM, and EPMA were used to study the microstructure of the coating. The results indicated that the oxidation took place throughout the entire coating instead of only at the surface. The aluminum phase in the composite coating was soon oxidized to Al₂O₃ in all tested cases. The aluminum in TiAl₃ phase was depleted gradually and oxidized to Al₂O₃ along with the degradation of TiAl₃ to TiAl₂ and TiAl as the temperature increased and time proceeded. AlTi₂N was also a typical oxidation product at temperature higher than 800 °C. The experimental results also indicated that the protection of the coating was attributed greatly to the interlayer formed between the coating and the substrate.     

Development and Application of Binary Suspensions in the Ternary System Cr<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for S-HVOF Spraying

Compositions in the system Cr₂O₃-TiO₂-Al₂O₃ are among the most used ceramic materials for thermally sprayed coating solutions. Cr₂O₃ coatings present good sliding wear resistance; Al₂O₃ coatings show excellent insulation behavior and TiO₂ striking corrosion properties. In order to combine these properties, coatings containing more than one oxide are highly interesting. The conventional spraying process is limited to the availability of binary feedstock powders with defined compositions. The use of suspensions offers the opportunity for tailor-made chemical compositions: within the triangle of Cr₂O₃-TiO₂-Al₂O₃, each mixture of oxides can be created. Criteria for the selection of raw materials as well as the relevant aspects for the development of binary suspensions in the Cr₂O₃-TiO₂-Al₂O₃ system to be used as feedstock for thermal spraying are presented. This formulation of binary suspensions required the development of water-based single-oxide suspensions with suitable behavior; otherwise, the interaction between the particles while mixing could lead up to a formation of agglomerates, which affect both the stability of the spray process and the coating properties. For the validation of this formulation procedure, binary Cr₂O₃-TiO₂ and Al₂O₃-TiO₂ suspensions were developed and sprayed using the S-HVOF process. The binary coatings were characterized and discussed in terms of microstructure and microhardness.     

Effects of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nano-Particles on Corrosion Performance of Plasma Electrolytic Oxidation Coatings Formed on 6061 Aluminum Alloy

Corrosion resistance improvement of plasma electrolyte oxidation coatings on 6061 aluminum alloy in silicate electrolyte containing Al₂O₃ nano-particles was studied, with particular emphasis on the microstructure, coating growth, and corrosion behavior in 3.5 wt.% NaCl solution. The microstructure of coatings, their thickness, and phase composition were characterized using scanning electron microscopy and x-ray diffraction. All characterization data showed that the maximum coating thickness and lowest amount of porosity were obtained in a low concentration of KOH, a high concentration of Na₂SiO₃, and moderate concentration of Al₂O₃ nano-particles in the electrolyte. This combination describes the optimum plasma electrolytic oxidation electrolyte, which has the best conductivity and oxidizing state, as well as the highest incorporation of electrolyte components in the coating growth process. On the other hand, incorporation and co-deposition of Al₂O₃ nano-particles were more pronounced than SiO₃ ^2? ions in some level of molar concentration, which is due to the higher impact of electron discharge force on the adsorption of Al₂O₃ nano-particles. The electrochemical results showed that the best protective behavior was obtained in the sample having a coat with the lowest porosity and highest thickness.     

Mechanical synthesis and rapid consolidation of nanocrystalline 3Fe<Subscript>0.67</Subscript>Cr<Subscript>0.33</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite by high frequency induction heating

Nanopowders of 3Fe_0.67Cr_0.33 and Al₂O₃ were synthesized from CrO₃ and 2FeAl powders by high-energy ball milling. A highly dense nanocrystalline 3Fe_0.67Cr_0.33-Al₂O₃ composite was consolidated by a high frequency induction heated sintering (HFIHS) method within three minutes from mechanically synthesized powders of Al₂O₃ and 3Fe_0.67Cr_0.33. The average grain size and mechanical properties of the composite were investigated.