Review of suspension and solution precursor plasma sprayed thermal barrier coatings

As one of the promising methods that can be employed to fabricate high-performance thermal barrier coatings (TBCs), suspension plasma spraying (SPS) or solution precursor plasma spraying (SPPS) has received significant attention in academic research. Enhanced performances have been shown in the SPS-/SPPS-coatings due to their special microstructures, such as uniformly distributed micro-pores, vertical cracks or columnar structures. Since there are more complexities than conventional plasma spraying methods, many works have been devoted to study the mechanism and properties of SPS-/SPPS-coatings during the past decades. In this work, the latest development of SPS or SPPS is reviewed in order to discuss some key issues in terms of preparation of suspension or solution precursor, injection mode of liquid phase, interaction between liquid and plasma jet, microstructure of as-sprayed coatings and corresponding deposition mechanism. Meanwhile, the potential application of SPS or SPPS in some new-type TBCs is introduced at the end of this paper.     

Design of high lifetime suspension plasma sprayed thermal barrier coatings

Thermal barrier coatings (TBCs) fabricated by suspension plasma spraying (SPS) have shown improved performance due to their low thermal conductivity and high durability along with relatively low production cost. Improvements in SPS TBCs that could further enhance their lifetime would lead to their widespread industrialisation. The objective of this study was to design a SPS TBC system with optimised topcoat microstructure and topcoat–bondcoat interface, combined with appropriate bondcoat microstructure and chemistry, which could exhibit high cyclic lifetime. Bondcoat deposition processes investigated in this study were high velocity air fuel (HVAF) spraying, high velocity oxy fuel spraying, vacuum plasma spraying, and diffusion process. Topcoat microstructure with high column density along with smooth topcoat–bondcoat interface and oxidation resistant bondcoat was shown as a favourable design for significant improvements in the lifetime of SPS TBCs. HVAF sprayed bondcoat treated by shot peening and grit blasting was shown to create this favourable design.     

等离子喷涂羟基磷灰石涂层

羟基磷灰石由于具有优良的生物性能，被广泛应用于生物材料领域，而等离子喷涂制备羟基磷灰石涂层是应用最为广泛的制备方法之一。在综合国内外献的基础上，本从羟基磷灰石的本征性能、喷涂工艺的影响、结合强度和梯度涂层等方面进行综述。     

Wetting,infiltration and interaction behavior of CMAS towards columnar YSZ coatings deposited by plasma spray physical vapor

Thermal barrier coatings (TBCs) produced by electron beam physical vapor deposition (EB-PVD) or plasma spray (PS) usually suffer from molten calcium-magnesium-alumino-silicate (CMAS) attack. In this study, columnar structured YSZ coatings were fabricated by plasma spray physical vapor deposition (PS-PVD). The coatings were CMAS-infiltrated at 1250?°C for short terms (1, 5, 30?min). The wetting and spreading dynamics of CMAS melt on the coating surface was in-situ investigated using a heating microscope. The results indicate that the spreading evolution of CMAS melt can be described in terms of two stages with varied time intervals and spreading velocities. Besides, the PS-PVD columnar coating (～100?μm thick) was fully penetrated by CMAS melt within 1?min. After the CMAS attack for 30?min, the original feathered-YSZ grains (tetragonal phase) in both PS-PVD and EB-PVD coatings were replaced by globular shaped monoclinic ZrO₂ grains in the interaction regions.     

Laser thermal gradient testing of air plasma sprayed multilayered,multi-material thermal barrier coatings

Air plasma sprayed (APS) thermal barrier coatings (TBCs) are a widely used technology in the gas turbine industry to thermally insulate and protect underlying metallic superalloy components. These TBCs are designed to have intrinsically low thermal conductivity while also being structurally compliant to withstand cyclic thermal excursions in a turbine environment. This study examines yttria-stabilized zirconia (YSZ) TBCs of varying architecture: porous and dense vertically cracked (DVC), which were deposited onto bond-coated superalloys and tested in a novel CO₂ laser rig. Additionally, multilayered TBCs: a two-layered YSZ (dense + porous) and a multi-material YSZ/GZO TBC were evaluated using the same laser rig. Cyclic exposure under simulative thermal gradients was carried out using the laser rig to evaluate the microstructural change of these different TBCs over time. During the test, real-time calculations of the normalized thermal conductivity of the TBCs were also evaluated to elucidate information about the nature of the microstructural change in relation to the starting microstructure and composition. It was determined that porous TBCs undergo steady increases in conductivity, whereas DVC and YSZ/GZO systems experience an initial increase followed by a monotonic decrease in conductivity. Microstructural studies confirmed the difference in coating evolution due to the cycling.     

Experimental visualization of microstructure evolution during suspension plasma spraying of thermal barrier coatings

This paper investigates the evolution of microstructure of thermal barrier coatings (TBCs) produced by suspension plasma spraying (SPS) through a careful experimental study. Understanding the influence of different suspension characteristics such as type of solvent, solid load content and median particle size on the ensuing TBC microstructure, as well as visualizing the early stages of coating build-up leading to formation of a columnar microstructure or otherwise, was of specific interest. Several SPS TBCs with different suspensions were deposited under identical conditions (same substrate, bond coat and plasma spray parameters). The experimental study clearly revealed the important role of suspension characteristics, namely surface tension, density and viscosity, on the final microstructure, with study of its progressive evolution providing invaluable insights. Variations in suspension properties manifest in the form of differences in droplet momentum and trajectory, which are found to be key determinants governing the resulting microstructure (e.g., lamellar/vertically cracked or columnar).     

Thermal cycling behavior of nanostructured 8YSZ，SZ/8YSZ and 8CSZ/8YSZ thermal barrier coatings fabricated by atmospheric plasma spraying

The nanostructured single-ceramic-layer (SCL) 8YSZ thermal barrier coatings (TBCs), double-ceramic-layer (DCL) Sm₂Zr₂O₇ (SZ)/8YSZ and SZ doped with 8 wt% CeO₂ nanoscale particles (8CSZ)/8YSZ TBCs were fabricated by atmospheric plasma spraying (APS) on nickel-based superalloy substrates with NiCoCrAlY as the bond coating. The thermal cycling behavior of the three as-sprayed TBCs was investigated systematically at 1000 ℃ and 1200 ℃. The results reveal that the thermal cycling lifetime of the nanostructured DCL 8CSZ/8YSZ TBCs is the longest among them, which is largely due to the fact that the intermediate layer buffer effect of the DCL structure, more porosity and improvement of thermal expansion coefficient from doping CeO₂ nanoparticles can relieve thermal stress to a great extent at elevated temperature. The failure mechanism of the nanostructured TBCs has been discussed in detail.     

Effect of scandia content on the thermal shock behavior of SYSZ thermal sprayed barrier coatings

Nanostructured 4SYSZ (scandia (3.5 mol%) yttria (0.5 mol%) stabilized zirconia) and 5.5 SYSZ (5 mol% scandia and 0.5 mol% yttria) thermal barrier coatings (TBCs) were deposited on nickel-based superalloy using NiCrAlY as the bond coat by plasma spraying process. The thermal shock response of both as-sprayed TBCs was investigated at 1000 °C. Experimental results indicated that the nanostructured 5.5SYSZ TBCs have better thermal shock performance in contrast to 4SYSZ TBCs due to their higher tetragonal phase content and higher fracture toughness of this coating     

Failure analysis of thermally cycled columnar thermal barrier coatings produced by high-velocity-air fuel and axial-suspension-plasma spraying: A design perspective

Axial-suspension-plasma spraying (ASPS) is a fairly recent thermal spray technology which enables production of ceramic top coats in TBCs, incorporating simultaneously the properties of both the conventional-plasma sprayed (highly insulating porous structures) and electron-beam-physical-vapor-deposited (strain-tolerant columnar structures) top coats. TBCs are required to insulate the hot components in a gas turbine engine against high temperature and harsh operating conditions. Periodic heating and cooling of turbine engines during operation can create severe thermal cyclic fatigue conditions which can degrade the performance of these coatings eventually leading to the failure. An in-depth experimental investigation was performed to understand the failure behavior of columnar TBCs subjected to thermal cyclic fatigue (TCF) test at 1100?C. The study revealed that the TCF performance was influenced to an extent, by the top coat microstructure, but was primarily affected by the severity of thermally grown oxide (TGO) growth at the bond coat-top coat interface. Mixed failure modes comprising crack propagation through the bond coat-TGO interface, through TGO and within the top coat were identified. Based on the analysis of the experimental results and thorough discussion a novel design of microstructure for the high TCF performance columnar TBC is proposed.     

Thermal cycling performances of multilayered yttria-stabilized zirconia/gadolinium zirconate thermal barrier coatings

Gadolinium zirconate (Gd₂Zr₂O₇, GZO) as an advanced thermal barrier coating (TBC) material, has lower thermal conductivity, better phase stability, sintering resistance, and calcium-magnesium-alumino-silicates (CMAS) attack resistance than yttria-stabilized zirconia (YSZ, 6-8 wt%) at temperatures above 1200°C. However, the drawbacks of GZO, such as the low fracture toughness and the formation of deleterious interphases with thermally grown alumina have to be considered for the application as TBC. Using atmospheric plasma spraying (APS) and suspension plasma spraying (SPS), double-layered YSZ/GZO TBCs, and triple-layered YSZ/GZO TBCs were manufactured. In thermal cycling tests, both multilayered TBCs showed a significant longer lifetime than conventional single-layered APS YSZ TBCs. The failure mechanism of TBCs in thermal cycling test was investigated. In addition, the CMAS attack resistance of both TBCs was also investigated in a modified burner rig facility. The triple-layered TBCs had an extremely long lifetime under CMAS attack. The failure mechanism of TBCs under CMAS attack and the CMAS infiltration mechanism were investigated and discussed.     

Architecture designs for extending thermal cycling lifetime of suspension plasma sprayed thermal barrier coatings

Suspension plasma spraying (SPS) as a relatively new spraying technology has great potential on depositing high performance thermal barrier coatings (TBCs). In some cases, however, columnar SPS TBCs show premature failure in thermal cycling test. To explain the reasons of such failure, a failure mechanism for columnar SPS TBCs was proposed in this work. The premature failure of TBCs might be related to the radial stresses in the vicinity of top coat/bond coat interface. These radial stresses were introduced by the thermal misfit and the roughness of bond coat. According to this mechanism, two architecture designs of SPS TBCs were applied to improve the thermal cycling lifetime. One was a double layered top coat design with a lamellar atmospheric plasma sprayed (APS) sub-layer and a columnar SPS top-layer. The other one was a low roughness bond coat design with a columnar SPS top coat deposited on a low roughness bond coat which was grinded before the spraying. With both designs, lifetimes of SPS TBCs were significantly extended. Especially, a lifetime even better than conventional APS TBCs was achieved with the double layered design.     

Thermal stability and sintering behavior of plasma sprayed nanostructured 7YSZ, 15YSZ and 5.5SYSZ coatings at elevated temperatures

Nanostructured scandia, yttria doped zirconia (5.5SYSZ), 7 wt% yttria stabilized zirconia (7YSZ) and 15YSZ thermal barrier coatings (TBCs) were produced by plasma spraying on nickel-based superalloy substrates with NiCrAlY as the bond coat. The thermal stability and sintering behavior of the three as-sprayed TBCs at 1480 °C were investigated. The results indicated that the thermal stability of SYSZ and TBCs was longer than the 7YSZ TBCs due to higher amount of tetragonal phase. Furthermore, the results demonstrated that the nanostructured 7YSZ coating exhibits higher sintering resistance than 5.5SYSZ TBC.     

Structure-property relationship and design of plasma-sprayed La2Ce2O7/8YSZ composite coatings for gas turbine blades

Novel lanthanum-cerium oxide/8?wt% yttria partially stabilized zirconia (LC/8YSZ) thermal barrier coatings (TBCs) were deposited by supersonic atmospheric plasma spraying. The thermal insulation temperature and thermal shock resistance of LC/8YSZ double-ceramic-layer TBCs (DCL-TBCs) were quantitatively evaluated by a burner rig test. The results showed that the thermal insulation temperature increased with the increase of LC layer thickness in DCL-TBCs. When the thickness ratio between LC layer and 8YSZ layer was close to 1:1, the DCL-TBCs had the highest thermal shock resistance. LC/8YSZ thickness ratio significantly affected the energy release rate and the stress induced by thermal gradient or sintering. The sintering stress was found to be the main reason that caused the delamination of LC layer, however, the stress induced by thermal gradient resulted in the spallation of YSZ layer.     

Failure mechanisms of calcium magnesium aluminum silicate affected thermal barrier coatings

Depth profiles of the phase composition of two examples of calcium magnesium aluminum silicate (CMAS) affected thermal barrier coatings (TBCs) from an aero gas turbine engine were obtained using a monochromatic and collimated beam of synchrotron radiation. One TBC was deposited by plasma spray and the other by electron beam physical vapor deposition. These examples were complemented with an X‐ray diffraction (XRD) study of mixtures of TBC zirconia powder and sand heated in a furnace. The XRD results were compared with electron backscatter images and energy dispersive spectroscopy studies of the cross sections and mixtures. It was found that when liquid, the CMAS enhances mass transport leading to the densification of the zirconia, which then leads to spalling because of the increased residual stresses generated on cooling. Even without spalling densification will reduce a TBC's ability to thermally insulate. The enhanced mass transport can also lead to destabilization of the zirconia if yttrium ions preferentially transfer to the liquid or greater stabilization if calcium or magnesium ions transfer from the liquid to the zirconia. Zircon also precipitates when the zirconium from the TBC reacts with the silicon in the liquid CMAS.     

Evaluation of major factors influencing the TBC topcoat formation in axial suspension plasma spraying (SPS)

Suspension plasma spraying (SPS) is ideally suited to produce porous or dense columnar, strain-tolerant thermal barrier coatings (TBCs) and also offers the possibility of producing other microstructures such as feathery and dense vertically cracked coatings. The specific properties of the TBC are significantly influenced by the formed microstructure, that is, affected by feedstock material and process parameters. In this work, the effects of various process parameters in the SPS process are investigated. It was found that the suspension feed rate has a significant effect on the microstructure, especially on the column density of the coating, whereas the suspension solids content mainly affects the coating porosity. Additionally, the surface roughness and topography of the bond coat are crucial for the formation of columnar coatings and were therefore investigated. Despite comparable roughness values for as-sprayed bond coats for high velocity oxy fuel and vacuum plasma spray produced coatings, the surface structures differ significantly from each other and affect the microstructure of the deposited topcoat. Characterization of mechanical properties by means of micro-indenter can be suitable for columnar coatings to determine Young's modulus within a column. However, due to the heterogeneity of the coating, the method is not suitable to describe the mechanical properties of the topcoat.     

等离子喷涂羟基磷灰石涂层

羟基磷灰石由于具有优良的生物性能，被广泛应用于生物材料领域，而等离子喷涂制备羟基磷灰石涂层是应用最为广泛的制各方法之一。在综合国内外文献的基础上，本文从羟基磷灰石的本征性能、喷涂工艺的影响、结合强度和梯度涂层等方面进行综述。     

Challenging zircon coatings by suspension plasma spraying

Zircon is a ceramic material that decomposes at high temperature, limiting its use by conventional thermal spraying. In this work, it is intended to use thermal spraying from concentrated aqueous suspensions to evaluate the possibility of obtaining coatings in which a significant proportion of zircon could be preserved. For this purpose, stable concentrated suspensions of zircon have been prepared, which have been subsequently sprayed at two different spraying distances. The coatings were characterised in terms of microstructural features and the amount of zircon present in the coatings was quantified. All the coatings obtained display the typical microstructure derived from the deposition of liquid feedstocks by plasma spraying. In all cases, the XRD analysis demonstrates the partial decomposition of zircon into zirconia and residual silica, but also that a significant percentage (about 20%) is preserved without decomposing, which marks a strong difference with respect to reported data for atmospheric plasma spraying.     

热喷涂技术的发展和应用

介绍了热喷涂技术的工艺特点.对超音速火焰喷涂、超音速等离子喷涂、激光喷涂、反应热喷涂和冷喷涂等5种不同的热喷涂工艺的优缺点进行了分析.总结了热喷涂技术的应用状况.探讨了新工艺、新材料在热喷涂技术中的应用前景.     

Laser surface modification of plasma sprayed CYSZ thermal barrier coatings

In this study, Inconel 738 LC superalloy coupons were first sprayed with a NiCoCrAlY bond coat and then with a ceria and yttria stabilized zirconia (CYSZ) top coat by air plasma spraying (APS). After that, the plasma sprayed CYSZ thermal barrier coatings (TBCs) were treated using a Nd:YAG pulsed laser. The effect of laser glazing on the microstructure of the coatings was investigated. The microstructures and surface topographies of both as-sprayed and laser glazed samples were investigated using field emission scanning electron microscope (FESEM) and atomic force microscope (AFM). The phases of the coatings were analyzed with X-ray diffractometry (XRD). The microstructural analysis results revealed that laser surface glazing of ceramic top coat reduced the surface roughness considerably, eliminated the surface porosities and produced a network of continuous cracks perpendicular to the surface. XRD patterns also showed that both as-sprayed and laser glazed top coats consisted of nonequibrium tetragonal (T′) phase.     

Thermal cycling and hot corrosion behavior of a novel LaPO4/YSZ double-ceramic-layer thermal barrier coating

LaPO₄ powders were produced by a chemical co-precipitation and calcination method. The ceramic exhibited a monazite structure, kept phase stability at 1400?°C for 100?h, and had low thermal conductivity (~ 1.41?W/m?K, 1000?°C). LaPO₄/Y₂O₃ partially stabilized ZrO₂ (LaPO₄/YSZ) double-ceramic-layer (DCL) thermal barrier coatings (TBCs) were fabricated by air plasma spray. The LaPO₄ coating contained many nanozones. Thermal cycling tests indicated that the spallation of LaPO₄/YSZ DCL TBCs initially occurred in the LaPO₄ coating. The failure mode was similar to those of many newly developed TBCs, probably due to the low toughness of the ceramics. LaPO₄/YSZ DCL TBCs were highly resistant to V₂O₅ corrosion. Exposed to V₂O₅ at 700–900?°C for 4?h, La(P,V)O₄ formed as the corrosion product, which had little detrimental effect on the coating microstructure. At 1000?°C for 4?h, a minor amount of LaVO₄ was generated.