Influence of cryogenic coolant on turning performance characteristics: A comparison with wet machining

Machining of 17-4 Precipitation Hardenable Stainless Steel (PH SS) is one of the difficult tasks because of its high cutting temperatures. Conventional cutting fluids are used to overcome the high cutting temperatures, but these are not acceptable from the health and environmental sustainable points of view. Cryogenic cooling is one of the potential techniques to overcome such problems. In the current work, comparison is made of cryogenic turning results, such as tool flank wear, cutting forces (feed force, main cutting force), cutting temperature, chip morphology and surface integrity characteristics with wet machining during machining of heat-treated 17-4 PH SS. The result showed that in cryogenic machining, a maximum of 53%, 78%, 35% and 16% reductions was observed in tool flank wear, cutting temperature, surface roughness and cutting force, respectively, when compared with wet machining. It was also evident from the experimental results that cryogenic machining significantly improved the machining performance and product quality even at high feed rates.     

Environment Friendly Machining of Ni–Cr–Co Based Super Alloy using Different Sustainable Techniques

In order to eradicate the use of mineral based cutting fluid, the machining of Ni–Cr–Co based Nimonic 90 alloy was conducted using environment friendly sustainable techniques. In this work, uncoated tungsten carbide inserts were employed for the machining under dry (untreated and cryogenically treated), MQL, and cryogenic cutting modes. The influence of all these techniques was examined by considering tool wear, surface finish, chip contact length, chip thickness, and chip morphology. It was found that the cryogenically treated tools outperformed the untreated tools at 40 m/min. At cutting speed of 80 m/min, MQL and direct cooling with liquid nitrogen brought down the flank wear by 50% in comparison to dry machining. Similarly at higher cutting speed, MQL and cryogenic cooling techniques provided the significant improvement in terms of nose wear, crater wear area, and chip thickness value. However, both dry and MQL modes outperformed the cryogenic cooling machining in terms of surface roughness value at all the cutting speeds. Overall cryotreated tools was able to provide satisfactory results at lower speed (40 m/min). Whereas both MQL and cryogenic cooling methods provided the significantly improved results at higher cutting speeds (60 and 80 m/min) over dry machining.     

Simplified MQL system for drilling AISI 304 SS using cryogenically treated drills

In machining operations, cutting fluids have been comprehensively used to improve the cutting tool life, but the issues related to manufacturing cost, environment and health call for reducing their use by possible methods. Minimum quantity lubrication (MQL) is a technique that overcomes these problems by spraying a small amount of cutting fluid (<100?ml/hr) as mist using compressed air. In this work, the basic MQL technique is used to achieve flow rates slightly higher (～880?ml/hr) than MQL using simple techniques like paint sprayer and compressor, which is more generally called reduced quantity lubrication (RQL). Another method to increase the tool life is by cryogenic treatment, which increases the hardness of the tool. Tungsten carbide drill bits were subjected to cryogenic treatment (?185 °C). Drilling studies were carried out on AISI 304 stainless steel (SS) using untreated and cryo-treated WC drill bits under RQL and conventional wet lubrication conditions. The tool wear on the treated WC drill bits with RQL was comparatively less than on the untreated ones with RQL and wet lubrication. These improvements were established through microhardness, SEM images, XRD, wear studies and surface roughness measurements comparisons.     

Machining of 6061 aluminium alloy with MQL, dry and flooded lubricant conditions

This paper reports on the effect of different lubricant environments when 6061 aluminium alloy is machined with diamond-coated carbide tools. The effect of dry machining, minimum quantity of lubricant (MQL), and flooded coolant conditions was analyzed with respect to the cutting forces, surface roughness of the machined work-piece and tool wear. The three types of coolant environments are compared. It is found that MQL condition will be a very good alternative to flooded coolant/lubricant conditions. Therefore, it appears that if MQL properly employed can replace the flooded coolant/lubricant environment which is presently employed in most of the cutting/machining applications, thereby not only the machining will be environmental friendly but also will improve the machinability characteristics.     

Experimental investigation of dry,wet and cryogenic boring of AA 7075 alloy

In this research work, an attempt has been carried out to examine (investigate) and study the dry, wet and cryogenic boring of AA 7075 alloy, which is predominantly used in transport applications in defense (aeronautical parts), oceanic and automaker industries. To ensure direct supply of the coolant, and real-time measurement of cutting temperature a modified boring bar is used (modification is carried out using EDM to accommodate placement of a thermocouple to obtain real-time measurement of temperature readings during the boring cycle). It is observed that during cryogenic boring of AA 7075 alloy there is a considerable reduction in the cutting force (F_c), cutting temperature (T_c) and surface roughness (R_a) by 56.16%, 84.70%, 58.98% compared to dry boring and 48.43%, 80.70%, 34.70% compared to wet boring, respectively. Decrease in F_c and T_c leads to a reduction in high stresses at localized points during machining and in turn curtail wear in workpiece and tool. Lubrication provided by cryogenic fluids also plays a sizable role in reduction of F_c and T_c. Reduction in lower F_c and T_c has a glaring effect on the surface characteristics of the hole produced during the boring process. Tool wear is reduced in cryogenic boring by 36.96% and 17.57% compared to dry and wet boring, respectively. Taguchi and ANOVA was carried out which helped in determining feed as an important parameter with respect to F_c and R_a during boring of AA 7075 under dry, wet and cryogenic conditions whereas speed as an important parameter in determining T_c in dry and wet conditions and feed for T_c in cryogenic boring condition. TOPSIS analysis highlighted speed of 770 rpm and feed of 0.055 mm/min as the most closest to ideal solution for all three different cutting conditions. Surface morphology study after boring of AA 7075 highlighted better surface characteristics in cryogenic bored surface compared to dry and wet boring. Roughness measured in AFM for tool used in boring highlighted a decrease in 86.79% and 66.01% in cryogenic boring in juxtaposition with dry and wet boring, respectively. A surge in compressive residual stress is observed in cryogenic bored surface by 10.41% and 3.5% in juxtaposition with dry and wet boring, respectively, highlighting an abatement in tensile residual stress and better workpiece integrity as compared to dry and wet boring conditions.     

Experimental investigation into the effects of nozzle position,workpiece hardness,and tool type in MQL turning of AISI 1045 steel

Minimum quantity lubrication (MQL) is a replacement for dry machining in which a minimum quantity of lubricant fluid is mixed up with compressed air and sprayed periodically on the machining area. In this research the effects of different parameters on the MQL turning of AISI 1045 steel have been investigated to evaluate the cutting force, surface roughness, and tool wear in comparison with the wet and dry machining. The research is aimed to study the effect of the MQL nozzle position, workpiece hardness and tool type on the output parameters. During MQL machining experiments, the nozzles were placed in three different arrangements relative to the tool to investigate the effect of the nozzle position. The effect of workpiece hardness and tool type were also studied experimentally for different lubrication conditions. The results indicated that the MQL system significantly increases the cutting efficiency in AISI 1045 steel machining. The experiments results have also confirmed a significant influence of the nozzle position, workpiece hardness, and tool type on the outputs. Machining with MQL is also beneficial to the environment and machine tool operator health as lubricant consumption during operation with MQL is 7-fold lower than in the conventional system.     

Experimental investigations on cryogenic cooling by liquid nitrogen in the end milling of hardened steel

Milling of hardened steel generates excessive heat during the chip formation process, which increases the temperature of cutting tool and accelerates tool wear. Application of conventional cutting fluid in milling process may not effectively control the heat generation also it has inherent health and environmental problems. To minimize health hazard and environmental problems caused by using conventional cutting fluid, a cryogenic cooling set up is developed to cool tool–chip interface using liquid nitrogen (LN₂). This paper presents results on the effect of LN₂ as a coolant on machinability of hardened AISI H13 tool steel for varying cutting speed in the range of 75–125 m/min during end milling with PVD TiAlN coated carbide inserts at a constant feed rate. The results show that machining with LN₂ lowers cutting temperature, tool flank wear, surface roughness and cutting forces as compared with dry and wet machining. With LN₂ cooling, it has been found that the cutting temperature was reduced by 57–60% and 37–42%; the tool flank wear was reduced by 29–34% and 10–12%; the surface roughness was decreased by 33–40% and 25–29% compared to dry and wet machining. The cutting forces also decreased moderately compared to dry and wet machining. This can be attributed to the fact that LN₂ machining provides better cooling and lubrication through substantial reduction in the cutting zone temperature.     

Development of ANFIS model and machinability study on dry turning of cryo-treated PH stainless steel with various inserts

This present investigation deals about the machinability comparison of cryogenically treated 15-5 PH stainless steel with various cutting tools such as uncoated tungsten carbide, cryogenic-treated tungsten carbide and wiper geometry inserts. Cryo-treated PH stainless steel is considered as the work material in this investigation and experimental trials were performed under dry turning condition. The machinability aspects considered for evaluation are cutting force (F_z), surface roughness (R_a) and tool wear. The outcomes of experimentation reveal that the tungsten carbide inserts which are cryogenically treated provide improved performance in machining while comparing with conventional and wiper geometry inserts at all machining conditions. The measured cutting force and the observed flank wear were less for the cryo-treated inserts. However, wiper tool produces a better surface finish during machining. An artificial intelligence decision-making tool named Adaptive Neuro Fuzzy Inference System has been evolved to determine the relation among the considered input machining variables and output measures, namely cutting force and surface roughness of the machined surface. An analysis has been performed to compare the results obtained from developed models and experimental results.     

Cryogenic turning of the Ti–6Al–4V alloy with modified cutting tool inserts

Productivity in the machining of titanium alloys is adversely affected by rapid tool wear as a consequence of high cutting zone temperature. Conventional cutting fluids are ineffective in controlling the cutting temperature in the cutting zone. In this research work, an attempt has been made to investigate the effect of liquid nitrogen when it is applied to the rake surface, and the main and auxiliary flank surfaces through holes made in the cutting tool insert during the turning of the Ti–6Al–4V alloy. The cryogenic results of the cutting temperature, cutting forces, surface roughness and tool wear of the modified cutting tool insert have been compared with those of wet machining. It has been observed that in the cryogenic cooling method, the cutting temperature was reduced by 61–66% and the surface roughness was reduced to a maximum of 36% over wet machining. The cutting force was decreased by 35–42% and the flank wear was reduced by 27–39% in cryogenic cooling over that of wet machining. Cryogenic cooling enabled a substantial reduction in the geometry of tool wear through the control of the tool wear mechanisms. The application of liquid nitrogen to the heat generation zones through holes made in the cutting tool insert was considered to be more effective over conventional machining.     

Tool wear in cryogenic turning of Ti-6Al-4V alloy

Though titanium alloys are being increasingly sought in a wide variety of engineering and biomedical applications, their manufacturability, especially machining and grinding imposes lot of constraints. Rapid tool wear encountered in machining of titanium alloys is a challenge that needs to be overcome. Cryogenic machining with liquid nitrogen as coolant is being investigated by researchers to reduce the cutting zone temperatures and enhance the tool life. The effects of cryogenic cooling have been studied on growth and nature tool wear in the present investigation while turning Ti-6Al-4V alloy bars with microcrystalline uncoated carbide inserts under dry, wet and cryogenic cooling environments in the cutting velocity range of 70-100 m/min. Cryogenic cooling by liquid nitrogen jets enabled substantial improvement in tool life through reduction in adhesion-dissolution-diffusion tool wear through control of machining temperature desirably at the cutting zone.     

Increased Surface Integrity in Porous Tungsten from Cryogenic Machining with Cermet Cutting Tool

In order to eliminate the process of backfilling porous tungsten with a plastic infiltrant during machining to prevent unwanted smearing of surface pores, cryogenic machining is investigated as a viable alternative. Porous tungsten is mainly used in the manufacture of dispenser cathodes where demands for surface quality and dimensional tolerances are extremely high. For these reasons, the ability of cryogenic machining to provide increased surface integrity and tool life compared to conventional dry machining is explored. Moreover, some preliminary results of machining with various cutting edge radii and effects on surface stress state are presented. Overall, cryogenic machining does provide significant surface quality and tool wear improvements over conventional dry machining practices.     

On Applicability of Multilayer Coated Tool in Dry Machining of Aerospace Grade Stainless Steel

The present research work has been undertaken with a view to investigate the influence of CVD multilayer coated (TiN/TiCN/Al₂O₃/ZrCN) and cutting speed on various machining characteristics such as chip morphology, tool wear, cutting temperature, and machined surface roughness during dry turning of 17-4 PH stainless steel. In order to understand the effectiveness of CVD multilayer coated tool a comparison has been carried out with that of uncoated carbide insert. The surface roughness and cutting temperature obtained during machining with chemical vapor deposition (CVD) multilayer coated tool was higher than that of uncoated carbide insert at all cutting velocity. However, the results clearly indicated that CVD multilayer coated tool played a significant role in restricting various modes of tool failure and reducing chip deformation compared to its uncoated counterpart. Adhesion and abrasion were found to be dominating wear mechanism with flank wear, plastic deformation, and catastrophic failure being major tool wear modes.     

Surface damages and tool wear mode in end milling of hastelloy‐C276 under dry and wet conditions

Hastelloy‐C276 is a nickel based superalloy that is widely used in chemical, petro‐chemical, environmental and nuclear industries due to its outstanding performance in a wide range of corrosive mediums. The superior properties of nickel based superalloys impair their machinability which increases the difficulty in obtaining a good surface finish. Because most of the components' failures are initiated from surface defects, several researchers have been concerned about surface integrity in machining aerospace superalloys particularly Inconel‐718. Due to the lack of studies done on machining corrosion‐resistant superalloys, this study aims to investigate surface damages and tool wear modes in milling Hastelloy‐C276 under dry and wet conditions. The absence of cooling and lubricating actions in dry machining resulted in the formation of craters, severe plastic deformation, voids, debris re‐deposition and materials drag. The breakage of the nucleated carbide phases resulted in the formation of nucleated cavities on the machined surface in both wet and dry machining. Adhesive tool wear was less in dry machining due to the formation of oxide layers on tool faces which suppressed the formation of built‐up edges due to the weak adhesion properties of oxide compounds which resulted in less surface roughness at v_c = 50 m/min. On the other hand, the higher temperature and friction in dry machining resulted in severer tool coating delamination.     

CRYOGENIC MACHINING OF KEVLAR COMPOSITES

Previous attempts to machine Kevlar aramid fibre reinforced plastics (KFRP) with conventional cutting tools have proven to be extremely difficult. This has somewhat restricted the material's usage, often negating the advantages of its high strength to weight ratio and fatigue tolerance. The present paper describes a novel technique of machining KFRP under cryogenic conditions with remarkable results compared to those obtained at ambient temperatures. The investigation carried out with turning operation shows dramatic improvement of the tool performance and surface quality. The effects of various machining parameters such as workpiece temperature, cutting speed and tool geometry on the machinability of KFRP are presented and analyzed. It appears that care is necessary to judge the tool life as the typical tool wear growth and surface finish or cutting force may produce contradictory results. It is also suggested that, for KFRP, surface finish of the machined workpiece is a very good criterion to determine the tool life. To aid the understanding of the machining mechanics, a microscopic investigation of the cutting zone while actually machining a testpiece at ambient and cryogenic temperatures is also reported.     

Effect of cryogenic minimum quantity lubrication on machinability of diamond tool in ultraprecision turning of 3Cr2NiMo steel

This work presents a series of experimental investigations and corresponding theoretical analyses to research on the effect of cryogenic minimum quantity lubrication (MQL) on machinability of diamond tool in ultraprecision turning of typical die steel. The tool wear and machined surface quality were determined as experimental indexes, which were measured using the scanning electron microscope and surface profiler, respectively. Besides, the maximum temperatures of diamond tool surfaces acquired by infrared thermal imager were used to indirectly evaluate the cutting process. The experimental results revealed that cryogenic MQL had obvious advantages in improving diamond tool durability and machined surface quality by comparison with flood cooling, cryogenic gas cooling, and MQL, and its essential function mechanisms were thoroughly understood. On the basis of this, carbon nanofluid was found to achieve optimal tool life in diamond turning compared with polyethylene glycol, castor oil, synthetic ester, and emulsified liquid. Ultimately, the combined machining method of ultrasonic vibration-assisted turning and cryogenic minimal quantity lubrication was proposed in this work. The results showed that this technique could observably improve the machinability of diamond tool and also provide a new direction for exploring a suitable processing method for ultraprecision machining of ferrous materials.     

Investigation on Some Machinability Aspects of Inconel 825 During Dry Turning

In the current study, attempt has been made to investigate the influence of cutting speed (Vc) (51, 84, and 124 m/min) on various machining characteristics like chip morphology, chip thickness ratio, tool wear, surface, and sub-surface integrity during dry turning of Inconel 825. Comparable study was carried out using uncoated and commercially available chemical vapor deposition multilayer coated (TiN/TiCN/Al₂O₃/ZrCN) cemented carbide (ISO P30 grade) insert. Chip morphology consists of chip forms obtained at different cutting conditions. Serrated chips were observed when machining Inconel 825 with both types of tool with more serration in case of uncoated insert. The chip thickness ratio increased as cutting speed was increased. Use of multilayer coated tool also resulted in increase in chip thickness ratio. Rake and flank surfaces were examined with scanning electron microscope and optical microscope. Abrasion, adhesion, and diffusion wears were found to be dominating tool wear mechanism during dry machining of Inconel 825. The beneficial effect of coated tool over its uncoated counterpart was most prominent during machining at high cutting speed (Vc = 124 m/min). The surface and sub-surface integrity obtained with coated tool were superior to that while machining Inconel 825 with uncoated tool.     

Experimental studies on the cryogenic machining of biodegradable ZK60 Mg alloy using micro-textured tools

Reducing the contact area between the cutting tool rake surface and chip promotes the machining performance of the work material and increases the tool life. Magnesium alloys are ductile-lightweight materials that form continuous chips during machining. The present investigation discusses the orthogonal turning of ZK60 magnesium alloy with linearly textured cutting inserts under both dry and liquid nitrogen (LN₂) cooling conditions. Linear grooves that are parallel and perpendicular to chip flow direction were created using Nd-YAG laser on the tungsten carbide cutting inserts. The effect of texturing combined with the application of LN₂ cooling is studied by evaluating the machining temperature and forces, microhardness, surface roughness and tool wear. Textured tools considerably minimize the liaison area of the chip with the rake plane compared to non-textured tools, which resulted in favorable effects in machinability. In case of cryogenic machining, textured tools substantially minimize the friction by the coupled effect of micro-pool lubrication and the formation of thin-film lubrication between the tool–chip/tool–work interfaces. Parallel-textured tools aided with cryogenic cooling exhibit superior performance during machining among the different types of tools employed in the present investigation.     

不同冷却润滑方式对切削SiCP/Al复合材料刀具磨损的影响

为探究不同冷却润滑方式对切削SiC_P/Al复合材料刀具磨损的影响,进行了干切削（Dry）、微量润滑（MQL）、液氮（LN₂）、切削油（Oil）和乳化液（Emulsion）共五种冷却润滑条件下的车削实验,分析了冷却润滑方式对刀具边界磨损、刀具破损和后刀面磨损的影响。结果表明:MQL和LN₂有更佳的流体冲刷效果,可以将脱落的SiC颗粒及时带离切削区,减少边界磨损; Oil和Emulsion冲刷效果较差,会加剧边界磨损。LN₂的使用会增加刀具受到的热应力和机械冲击,积屑瘤发生完全脱落,造成切削过程不平稳,当切削距离达到1 100 m时,刀具发生破损; Oil切削时,严重的边界磨损导致刀尖部位尺寸减小,强度降低,当切削距离达到825 m时发生了刀具破损。MQL良好的润滑渗透性和LN₂有效的冷却效果可以减少后刀面磨损。因此,MQL兼具冷却、润滑和流体冲刷效果,更加适合作为切削SiC_P/Al复合材料的冷却润滑方式。      

Machinability studies on Al 7075/BN/Al2O3 squeeze cast hybrid nanocomposite under different machining environments

Enforcement of stricter environmental policies demands alternative methods that could reduce the usage of cutting fluid during machining. Thus, dry machining and minimum quantity lubrication (MQL) machining are gaining practical importance. Due to enhanced mechanical and thermal properties, aluminium based nanocomposites have wide application in aerospace and automobile industries. In this work, asqueeze cast hybrid nanocomposite is developed with the reinforcement of 0.5?wt% hexagonal boron nitride and 1?wt% alumina particles in the base matrix of Al 7075 that is subjected to a squeezing pressure of 150?MPa. During the turning of this hybrid nanocomposite, thefeed rate is varied (0.1, 0.2, and 0.3?mm/rev)and its influence on the generated forces, tool wear and surface roughness under dry and MQL environments is performed. The results are compared with squeeze cast unreinforced aluminium alloy and presented.     

Experimental investigation of tool wear and chip formation in cryogenic machining of titanium alloys

Titanium alloys are one of the most important design materials for the aircraft industry.The high strength-to-density-ratio and the compatibility with carbon fibre reinforced plastic are the reasons for a raising application in this field.The outstanding properties lead to challenging machining processes.High strength and low heat conductivity affect high mechanical and thermal loads for the cutting edge.Thus,the machining process is characterized by a rapid development of tool wear even at low cutting parameter.To reach a sufficient productivity it is necessary to dissipate the resulting heat from the cutting edge by a coolant.Therefore the cryogenic machining of two different titanium alloys is investigated in this work.The results point out the different behavior of the machining processes under cryogenic conditions because of the reduced thermal load for the cutting tool.According to this investigation,the cryogenic cooling with CO_2enables an increase of the tool life in comparison to emulsion based cooling principles when machining theα+β-titanium alloy Ti-6Al-4V.The machining process of the high strength titanium alloy Ti-6Al-2Sn-4Zr-6Mo requires an additional lubrication realized by a minimum quantity lubrication(MQL) with oil.This combined cooling leads to a smoother chip underside and to slender shear bands between the different chip segments.