Enhanced mechanical properties of glass fibre epoxy composites by 2D exfoliated graphene oxide filler

Graphene oxide (GO) received a significant attention in the scientific community due to their excellent mechanical properties identifying themselves as an alternative and combinatory to various other metals and composites. Though GO possess excellent strength, it was observed from the literature that graphene oxide consisting of hydroxyl group elements ensue in poor bonding. Thus reduced functional group density (rFGD) graphene is preferred which has an advantage of good bonding, alongside very small quantity as a filler is required to achieve the enhancement equivalent to graphene oxide which forms the novelty of the current work. In current case, 3, 6 and 9 wt% of rFGD is dispersed into E-glass fibre reinforced composite by traditional hand layup technique. The obtained results revealed that, the tensile, flexural and impact strength have shown superior enhancement with 3 and 6 wt% of rGO than neat E-glass epoxy (0 wt% rGO), whereas an asymptotic decrement is noticed at 9 wt% when tested with ASTM standards except for impact strength. The microstructural studies also indicated the proper adhesion and alignment of fibres without any agglomerations corroborate the enhancement of properties. These overall finding supports the suitability of the developed laminates for potential use in structural applications in aerospace industry.     

Investigation of thermal properties and mechanical properties of reduced graphene oxide/polyimide resin composites

In this article, reduced graphene oxide/polyimide resin composites which exhibited enhancements in mechanical properties were successfully fabricated by hot‐pressing, and reduced graphene oxide nanosheets were synthesized by thermal reduced method, which can readily mix with PI powders in aqueous solution by sonication process. The chemical structures of rGO were carefully characterized by X‐ray diffraction, Fourier transfer infrared spectroscopy and X‐ray photoelectron spectroscopy. The field emission scanning electron microscopy observations showed that the rGO displayed excellent dispersibility and compatibility with the PI matrix. The mechanical analysis indicated that the tensile and flexural strength values of the rGO/PI resin composite with 1.5 wt% rGO loading reached 80.7 and 133.3 MPa, respectively. Compared with pure PI, the optimized rGO/PI resin composite exhibited an enhancement of 30% in tensile strength, 19% in flexural strength and 27% in impact strength, due to the fine dispersion of high specific surface area of graphene nanosheets and the good adhesion between the rGO and the matrix. In addition, thermogravimetric analysis, dynamic mechanical analysis, and dielectric properties were also investigated. POLYM. COMPOS., 38:2321–2331, 2017. © 2015 Society of Plastics Engineers     

Preparation of Ag/reduced graphene oxide reinforced copper matrix composites through spark plasma sintering: An investigation of microstructure and mechanical properties

The reduced graphene oxide (rGO) decorated with Ag nanoparticles was synthesized by the chemical reduction of graphene oxide in an aqueous solution containing AgNO₃, in the presence of hydrazine hydrate as a reducing agent. The reduction of graphene oxide was confirmed by FT-IR and raman spectroscopy analyses. The x-ray diffraction pattern and UV–visible investigations demonstrated the formation of Ag particles on the surface of rGO sheets. After successful decoration, the Ag/rGO nano-composite was used as the reinforcement in the copper matrix composite. Cu–Ag/rGO composites with different percentages of Ag/rGO (0.4, 0.8, 1.6 and 3.2 vol%.) were prepared by mechanical milling and spark plasma sintering (SPS). The effects of the Ag/rGO content on the consolidation process, micro-hardness, bending strength and also, fracture surface of the prepared samples were then investigated. The three-point bending strength of the sintered samples was increased from 285 to 472 MPa by the addition 0.8 vol%. of Ag/rGO, as compared to the pure Cu. Moreover, increasing the reinforcement content to the 3.2 vol%. Ag/rGO led to decreasing the bending strength to 433 MPa. The highest micro-hardness (81 Hv) was obtained for the composite sample containing the 1.6 vol%. Ag/rGO. By increasing Ag/r-GO as the reinforcement (3.2 vol%.), the Vickers hardness was decreased to 69 Hv. Also, investigation of the fracture surface morphology showed transformation of fracture mechanism from plastic changes to brittle ones by raising the Ag/rGO content volume from 0.8 to 1.6 vol %.     

Preparation of well‐dispersed reduced graphene oxide and its mechanical reinforcement in polyvinyl alcohol fibre

The current work reports the preparation and characterization of polyvinyl alcohol (PVA) composite fibres reinforced with graphene reduced from graphene oxide (GO) by using oligomeric proanthocyanidin (OPC) as a reductant. After reduction, most of the oxygen‐containing groups were removed from the GO and reduced graphene oxide (rGO) was prepared. As a result of combined OPC as a dispersant, rGO could be well dispersed in a dimethyl sulfoxide/H₂O mixed solvent and in PVA matrix, and the PVA/rGO dispersion was wet spun followed by hot drawing to prepare continuous PVA/rGO composite fibres. The PVA/rGO composite fibres exhibited a significant enhancement of mechanical properties at low rGO loadings; in particular the tensile strength and Young's modulus of the 2.0 wt% rGO and PVA composite fibre increased to 244% and 294% respectively relative to neat PVA fibre. Moreover, the storage modulus (?10 °C) and T_g increased to 300% and 7.2 °C, respectively. © 2016 Society of Chemical Industry     

A facile one step electrostatically driven electrocodeposition of polyviologen–reduced graphene oxide nanocomposite films for enhanced electrochromic performance

Polyviologen (PV)–reduced graphene oxide (rGO) nanocomposite films were fabricated by simple, one-step reductive electropolymerization of cyanopyridinium based precursor monomer (CNP) in an aqueous dispersion of graphene oxide (GO). Since the polymer formation and reduction of graphene oxide occurs within the same potential window, electrocodeposition method was preferred for obtaining nanostructured PV–rGO films. Cyclic voltammetry experiments of PV–rGO displayed two well resolved, reversible one-electron redox processes typical of viologen. Being a redox polymer, incorporation of rGO further enhances the electroactivity of the PV in the composite films. Vibrational spectral analysis with surface characterization revealed structural changes after composite formation along with subsequent reduction of GO within the polymer matrix. The PV–rGO nanostructured film exhibits a high-contrast electrochromism with low driving voltage induced striking color changes from transparent (0 V) to purple (−0.6 V), high coloration efficiency, fast response times and better cycling stability compared to a pristine PV film. This improved performance can be attributed to the high stability of the electrochrome in the composite assembly induced by electrostatically driven non-covalent interactions between redox PV²⁺ and negatively charged rGO, improved electrical conductivity and enlarged surface area accessed through reinforced nanostructured graphene sheets for tethering PV molecules.     

Mechanical and dielectric properties of reduced graphene oxide nanosheets/alumina composite ceramics

Reduced graphene oxide (rGO) nanosheets/alumina (Al₂O₃) composite ceramics were fabricated by hot-pressing sintering. The density, porosity, microhardness, flexural strength and complex permittivity were investigated to study their mechanical and dielectric properties. The results revealed that the rGO nanosheets were uniformly distributed in the Al₂O₃ matrix and that the composite ceramics were highly dense at 3.67–3.99 g/cm³. Due to low rGO hardness and elevated porosity, the microhardness exhibits a decreasing trend as the rGO content increases. The flexural strength first increased and then decreased with the escalation of rGO content, and the highest strength of 313.75 MPa was obtained at 3 wt%, increasing by 37.61% relative to that of the hot-pressing sintered Al₂O₃ ceramic. Owing to the enhanced interfacial polarization, dipole polarization, polarization relaxation loss and conductance loss, the real part and imaginary part of complex permittivity increase from 10.40 to 52.73 and from 0.08 to 28.86 as the rGO content rose from 0 wt% to 4 wt%, respectively.     

Sintering effect on microstructural evolution and mechanical properties of spark plasma sintered Ti matrix composites reinforced by reduced graphene oxides

Ti matrix composites reinforced with 0.6?wt% reduced graphene oxide (rGO) sheets were fabricated using spark plasma sintering (SPS) technology at different sintering temperatures from 800?°C to 1100?°C. Effects of SPS sintering temperature on microstructural evolution and mechanical properties of rGO/Ti composites were studied. Results showed that with an increase in the sintering temperature, the relative density and densification of the composites were improved. The Ti grains were apparently refined owing to the presence of rGO. The optimum sintering temperature was found to be 1000?°C with a duration of 5?min under a pressure of 45?MPa in vacuum, and the structure of rGO was retained. At the same time, the reaction between Ti matrix and rGO at such high sintering temperatures resulted in uniform distribution of micro/nano TiC particle inside the rGO/Ti composites. The sintered rGO/Ti composites exhibited the best mechanical properties at the sintering temperature of 1000?°C, obtaining the values of micro-hardness, ultimate tensile strength, 0.2% yield strength of 224 HV, 535?MPa and 446?MPa, respectively. These are much higher than the composites sintered at the temperature of 900?°C. The fracture mode of the composites was found to change from a predominate trans-granular mode at low sintering temperatures to a ductile fracture mode with quasi-cleavage at higher temperatures, which is consistent with the theoretical calculations.     

Synthesis of MnOx/reduced graphene oxide nanocomposite as an anode electrode for lithium-ion batteries

We report the high performance of the manganese oxide/reduced graphene oxide (MnOx/rGO) nanocomposite as an anode electrode of a lithium-ion battery. The composite is synthesized by a low temperature (83 °C) chemical solution reaction, and shows relatively high specific capacities (660 mAh g⁻¹) after 50 cycles. For MnOx/rGO composites, the cycling stability is increased remarkably as compared to that seen with individual MnOx, and this is due to the synergistic effects of both the components in the composite. The rGO acts as a conductive buffer layer that suppresses the volume change of MnOx, and simultaneously promotes the conductivity of MnOx. The functional groups of graphene oxide facilitate MnOx formation at low temperature, and this retains the MnOx-graphene oxide connection, thus improving the capacity and cycling stability.     

Investigation of electrical,mechanical, and thermal properties of functionalized multiwalled carbon nanotubes‐reduced graphene Oxide/PMMA hybrid nanocomposites

Electrical, mechanical, and thermal properties of the poly(methyl methacrylate) (PMMA) composites containing functionalized multiwalled carbon nanotubes (f‐MWCNTs) and reduced graphene oxide (rGO) hybrid nanofillers have been investigated. The observed electrical percolation threshold of FHC is 0.8 wt% with maximum conductivity of 1.21 × 10^?3 S/cm at 4 wt% of f‐MWCNTs. The electrical transport mechanism and magneto resistance studied of hybrid composites have also been investigated. Progressive addition of f‐MWCNTs in rGO/PMMA composite results increase in mechanical (tensile strength and Young's modulus) and thermal (thermal stability) properties of f‐MWCNTs‐rGO/PMMA hybrid nanocomposites (FHC). The increased mechanical properties are due to the efficient load transfer from PMMA matrix to f‐MWCNTs and rGO through better chemical interaction. The strong interaction between PMMA and f‐MWCNTs‐rGO in FHC is the main cause for improved thermal stability. POLYM. ENG. SCI., 59:1075–1083, 2019. © 2019 Society of Plastics Engineers     

石墨烯/玻璃块体复合材料的制备及性能

本文报道了还原氧化石墨烯/钠钙硅(rGO/SLS)玻璃块体复合材料的热压制备和力学性能。首先以3-氨基丙基三乙氧基硅烷为表面活性剂修饰玻璃粉微粒;然后在水溶液中带负电的氧化石墨烯(GO)纳米片通过静电自组装与被氨基修饰过带正电的玻璃颗粒相结合生成复合颗粒。通过高温真空热压烧结,GO被还原成rGO,从而原位生成rGO/SLS玻璃块状复合材料。结果表明,rGO均匀分布在玻璃基质中,并明显增强了复合材料的机械性能。rGO/SLS玻璃块体复合材料中rGO的含量为0.5%(质量分数)时,复合材料的弯曲强度比纯的SLS玻璃提高了约一倍。     

Preparation and properties of reduced graphene oxide/fused silica composites

An in situ strategy for fabrication of reduced graphene oxide/fused silica (rGO/FS) composites using 3-aminopropyltriethoxysilane as surfactant is reported. GO nanosheets were bound to FS particles by an electrostatic assembly between ultra thin negatively charged GO sheets and positively charged amino-modified FS particles. After spark plasma sintering, rGO/FS bulk composites have been produced from the GO and FS composite particles with GO being reduced to rGO in vacuum at high temperatures. Results show that rGO sheets were well dispersed in the matrix, and conductivity of these rGO/FS composites at room temperature was strongly dependent on the rGO nanosheet concentration. i.e., the conductivity of rGO/FS was increased to 10⁻⁴ S/cm when a conducting network was formed inside the composites. The effect of GO nanosheets on the mechanical properties of rGO/FS bulk composites was also investigated. The addition of 1 wt.% GO sheets to FS resulted in 72% increase in Vickers hardness, indicating the stress transfering from the FS matrix to the rigid rGO sheets. With the same rGO content, the fracture toughness of the as-prepared composites was increased by 74%. The main toughening mechanisms were thought to be crack deflection, crack branching, pulling-out and bridging of the rGO sheets.     

Proanthocyanidin‐Induced Horizontal Arrangement in Poly(vinyl alcohol)/Graphene Composites with Enhanced Mechanical Properties

A green approach is employed to prepare mechanically enhanced composites by adding noncovalently proanthocyanidin (PC)‐modified graphene (PC‐rGO) into poly(vinyl alcohol) (PVA). Ascorbic acid (AA) is used as the reducing agent, and PC is used as a dispersant to synthesize low‐defect and fully dispersed graphene. After static treatment, the PC‐rGO sheets in the composite form a horizontally arranged structure. Compared with neat PVA, the Young's modulus of the graphene‐modified composites is significantly enhanced by approximately 79.3% with incorporation of 0.9 wt% PC‐rGO. The composites incorporated with GO or AA‐rGO (without PC) have randomly distributed GO structures and apparent rGO agglomeration, resulting in a weaker mechanical property. The dispersibility, degree of defects, distribution state of graphene, and interactions with the polymer matrix are directly related to the final mechanical performance. This new approach to mechanically enhance graphene‐embedded PVA composites provides the possibility for large‐scale production of graphene‐reinforced composite materials.     

Enhanced toughness and strength of boron carbide ceramics with reduced graphene oxide fabricated by hot pressing

Boron carbide (B₄C) hybrids with different contents of graphene oxide (GO) were prepared by a heterogeneous co-precipitation method using cetyltrimethyl ammonium bromide (CTAB) as the cationic surfactant. The as-obtained mixtures were further hot-pressed at 1950 °C for 60 min under 30 MPa, by which B₄C–reduced GO (rGO) composites were fabricated. It was found that the addition of only 0.5 wt% rGO could alter the predominance of trans-granular fracture in monolithic B₄C ceramic material to mixed trans-granular and inter-granular modes in B₄C–rGO composites. The flexural strength and fracture toughness of the B₄C–2 wt% rGO were increased by 31% (from 350 to 455 MPa) and 83% (from 3.20 to 5.85 MPa·m^1/2), respectively, compared with those of pure B₄C. The improved mechanical properties are attributed to the mechanisms of pull-out and bridging of rGO and crack deflection, as evidenced by microstructural observations. The energy dissipation in the present B₄C–rGO composites was further verified using two micromechanical models.     

Structural,dielectric, and magnetic properties of reduced graphene oxide-wrapped MnFe2O4 composites synthesized by in-situ sol-gel autocombustion method

Herein, the reduced graphene oxide (rGO) wrapped MnFe₂O₄ (MFO@rGO) composites with different rGO content of 10, 20, 30, and 40 wt% have been synthesized by a one-step in-situ sol-gel autocombustion method. The synthesized composites have been tested for their structural, electrical, dielectric, and magnetic characteristics. The composites are characterized by using standard techniques (XRD, HR-TEM, FTIR, and Raman spectroscopy). The composite having 20 wt% of rGO exhibits the highest value of dielectric constant (ε′～1.32 × 10⁴ at 100 Hz, ε′～143 at 1 MHz) and dc conductivity (σ_dc = 4.31 × 10^?6 Ω^?1-cm^?1) among the investigated composites. The dipole polarization contribution to the dielectric relaxation behavior of MFO@rGO composites is observed, which arises from the increased vacancy defect dipoles in rGO sheets. The impedance studies show the existence of two different time relaxation phenomena in MFO@rGO composites. The magnetic measurements reveal the superparamagnetic behavior of composites. The saturation magnetization of composites decreases first with the increase in rGO content up to 20 wt% and then increases with a further increase in rGO content. The findings of this research make these composites a potential candidate for various applications such as EMI shielding and energy storage devices.     

Mechanical properties and biomedical applications of a nanotube hydroxyapatite-reduced graphene oxide composite

As a result of the growing interest in the biological and mechanical performance of hydroxyapatite (HA)–graphene nano-sheets (GNs) composite systems, reduced graphene oxide (rGO) reinforced hydroxyapatite nano-tube (nHA) composites were synthesized in situ using a simple hydrothermal method in a mixed solvent system of ethylene glycol (EG), N,N-dimethylformamide (DMF) and water, without using any of the typical reducing agents. The consolidation process was performed by hot isostatic pressing (HIP) at 1150 °C and 160 MPa. The composites were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and Raman spectroscopy, enabling confirmation of the synthesis and reduction of the nHA and rGO, respectively. The structure of the synthesized powder and cell attachment on the sintered sample was confirmed by field emission scanning electron microscopy (FESEM). The effects of the rGO on the mechanical properties and the in vitro biocompatibility of the nHA based ceramic composites were investigated. The elastic modulus and fracture toughness of the sintered samples increased with the increase of the rGO content when compared to the pure nHA by 86% and 40%, respectively. Cell culture and viability test results showed that the addition of the rGO promotes osteoblast adhesion and proliferation, thereby increasing the biocompatibility of the nHA–rGO composite.     

Synergistic strengthening effect of graphene-carbon nanotube hybrid structure in aluminum matrix composites

High-performance reinforcement and tailored architecture are currently explored to develop advanced metal matrix composites. In this work, aluminum (Al) matrix composite reinforced by hybrid carbon nanofillers was fabricated by a composite flake assembly process. It was found that for various carbon nanofiller volume fractions, a striking synergistic strengthening effect was achieved by employing graphene (reduced graphene oxide, RGO) and carbon nanotube (CNT) hybrid structure as reinforcement in the Al matrix. Particularly, a tensile strength of 415 MPa was achieved with the addition of 1.5 vol.% of RGO-CNT hybrid, which is significantly higher than those reinforced by individual CNT or RGO (326 and 331 MPa, respectively). The synergistic strengthening effect was attributed to the formation of a planar network of RGO and CNT, which improves the load transfer efficiency between the matrix and the reinforcement in composites. Our study highlights the importance of reinforcement architecture for enhancing the strengthening ability in composites, and provides an effective route to fully take the advantage of the superior properties of various reinforcements.     

Enhancing toughness and strength of SiC ceramics with reduced graphene oxide by HP sintering

In this paper, the silicon carbide-reduced graphene oxide (SiC/rGO) composites with different content of rGO are investigated. The hot pressing (HP) at 2100?°C for 60?min under a uniaxial pressure of 40?M?Pa resulted in a near fully-dense SiC/rGO composite. In addition, the influence of graphene reinforcement on the sintering process, microstructure, and mechanical properties (fracture toughness, bending strength, and Vickers hardness) of SiC/rGO composites is discussed. The fracture toughness of SiC/rGO composites (7.9MPam^1/2) was strongly enhanced by incorporating rGO into the SiC matrix, which was 97% higher than the solid-state sintering SiC ceramics (SSiC) by HP. Meanwhile, the bending strength of the composites reached 625?M?Pa, which was 17.3% higher than the reference materials (SSiC). The microstructure of the composites revealed that SiC grains were isolated by rGO platelets, which lead to the toughening of the composite through rGO pull out/debonding and crack bridging mechanisms.     

聚偏氟乙烯/石墨烯复合材料的制备及性能研究

用溶液共混法制备出聚偏氟乙烯/氧化石墨烯复合材料(PVDF/GO),经高温热压将GO还原得到聚偏氟乙烯/还原氧化石墨烯复合材料(PVDF/rGO)。研究了填料种类及含量对复合材料电学性能、热稳定性和力学性能的影响。结果表明：随GO和rGO的添加,两种复合材料的介电常数(ε _r)均变大、介电损耗(tanδ)变化不大;低含量下GO和rGO均能提高PVDF的热稳定性,但rGO对PVDF性能的改善效果更好;随填料含量从0增加到8%(质量),100 Hz下PVDF/rGO复合材料的ε _r从3.60增加到38.30,PVDF/rGO[4%(质量)]复合材料失重率为5%的分解温度较纯PVDF提高了6.44℃。rGO增强了PVDF的刚性,PVDF/rGO复合材料的拉伸强度先增大后减小,杨氏模量逐渐增大,当rGO含量为4%(质量)时拉伸强度最大,拉伸强度和弹性模量分别较纯PVDF提高了35.30%、22.58%。但GO和rGO都降低了复合材料的击穿场强。     

Fabrication of ZrO2/rGO nanocomposites by flash sintering under AC electric fields

Ceramic matrix nanocomposites containing graphene possess superior mechanical properties. However, these nanocomposites are very difficult to be prepared using the conventional methods due to severe grain growth and simultaneous degradation of the graphene at high sintering temperatures and long dwell time. Herein, the dense ZrO₂/rGO (reduced graphene oxide) nanocomposites are successfully fabricated by flash sintering of the green compacts consisting of ZrO₂ nanoparticles and graphene oxide (GO) at 893–951℃ in merely 5 seconds under the alternating current (AC) electric fields of 130–150 V cm⁻¹. The GO can be in situ thermal reduced during the flash sintering. The as-prepared ZrO₂/rGO nanocomposites exhibit excellent mechanical properties. This study presents a green and simple approach to fabricate the dense ceramic matrix nanocomposites reinforced with graphene at low temperatures in a short time.     

Preparation of highly conductive reduced graphite oxide/poly(styrene-co-butyl acrylate) composites via miniemulsion polymerization

Polymer/reduced graphite oxide (rGO) composite nanoparticles with a high electrical conductivity were synthesized using the miniemulsion polymerization technique. The rGO was modified with a reactive surfactant, 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS), to facilitate monomer intercalation into the rGO nanogalleries. The AMPS-modified rGO was emulsified in the presence of styrene (St) and butyl acrylate (BA) monomers, and the stable miniemulsion was polymerized to form poly(St-co-BA)/rGO composite latex nanoparticles. The transition in the composite nanoparticles from an electrical insulator to an electrical conductor occurred at an rGO content of 10 wt% (relative to the monolayer content), yielding an electrical conductivity of 0.49 S/cm. The electrical conductivity of the composite nanoparticles reached 2.22 S/cm at 20 wt% rGO, yielding a much better conductivity than other polymer composites prepared using a GO filler. Importantly, the miniemulsion polymerization method for fabricating poly(St-co-BA)/rGO composite nanoparticles is easy, green, low-cost, and scalable, providing a universal route to the rational design and engineering of highly conductive polymer composites.